Red eye correction not saving, Red eye correction not saving

I open iphoto and try to auto-fix red eye in one picture but it's not an option. So I manually fix it but once I hit "done" the red eye correction does not save. I have iphoto'11.

I hit "done" the red eye correction does not save.
Perhaps your library is corrupted. Try to repair your iPhoto library.
Launch iPhoto with the key combination ⌥⌘ held down and try the first aid options "repair permissions" and "repair database", if necessary also "rebuild database". Before you do any repairing, make sure that the backup of your iPhoto library is up to date.
Regards
Léonie

Similar Messages

One eye no result in red eye correction?

When I put a portrait photo into iPhone, and used red eye removal separately on both eyes, one eye only was corrected, but the second eye would not change, but remained red: tried one at a time, and also tried in Preview.
Any suggestions? Thanks

Well, now I can try to help your. Assuming you're running iPhoto 11 make a temporary, duplicate copy of the library and try the two fixes below in order as needed:
Fix #1
1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your Home/Library/Preferences folder.
2 - delete iPhoto's cache files that are located in your Home/Library/Caches/com.apple.iPhoto folder.
3 - reboot, launch iPhoto and try again.
NOTE: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding the the Option key. You'll also have to reset the iPhoto's various preferences.
Fix #2
Launch iPhoto with the Command+Option keys depressed and follow the instructions to rebuild the library. Select options #1, #2 and #6.
Click to view image full size

Saving red eye reduction

appears to save red eye reduction but it doesn't save. i follow the instructions: 1) open the photo in an album in edit mode 2)select red eye reduction tool 3)remove red eye 4)turn off red eye reduction tool 5)click "done". system says it's saving. when i check the red eye is still there.

Stephanie,
Welcome to the Apple Discuccions.
The first and easiest fix to try is to delete the iPhoto preference file. Close iPhoto. In the Finder, look inside Home/Library/Preferences. Find a file named com.apple.iPhoto.plist and drag it to the Trash. Launch iPhoto. It will create a new pref file, and your preferences will be reset to their defaults. Change them back to your liking. Try to edit a photo and see if it sticks now. If not, look to see if the file is locked.
Photos, Get Info brings up the iPhoto info. You need the Finder's Info. Right-click on the photo's thumbnail from within iPhoto and select "Show File" from the pop-up menu. A Finder window should then open up with the photo already selected. Type Command-I (or click the "More Info..." button below the thumbnail in column view) to bring up the Finder's info about that file.
The top section of the info window is called General. The last thing in that section is a little box by the word Locked. If there's an x in the box, click to remove it. You can also look at the bottom of the Info box, at the section called Ownership & Permissions. Next to "You can" it should say "Read & Write." Open the Details section below that to see who has Ownership of the file.

How can I add a red line below all those words, which are not technically correct? And how can I do Pages to do it automatically?

So, how can I add the red line below all those words, which are not technically correct.
I have tried everything, but nothing works. Red line should come there automatically, but I can't find nothing from settings to do this. Can you guys help me?

There isn't any finnish spellcheck in Pages
Inspector palette = Asetukset
I am trying to find out where to get a finnish dictionary that can work in Pages. I am not sure but try this
http://www.jkwchui.com/2010/03/spellchecking-latex-in-macosx/

How can I correct and prevent white eyes when taking picture with my Iphone4S?

How can I correct and prevent white eyes when taking picture with IPhone 4S?

Hi Friend,
To correct red eyes on pictures, go to Photos app, tap the photo you want correct, tap Edit, Tap a red ball placed in the bottom of the screen, tap manually the red eyes, and Confirm.
Hope it will be helpful

My blends in Illustrator CS4 are not saving or printing correctly. Why?

Why are my blends in Illustrator CS4 not saving or printing correctly???
SPECS:
Adobe CS4
MAC 10.5.8
I got a outlined Text blend with a drop shadow. And another text with a drop shadow on top. Not too complex at all.
Heres some screenshots of the problem.
(1) Adobe Illustrator Screenshot
(1) Screenshot of my saved TIff file. I saved as a PDF as well and still no luck.
Any suggestions?

Mylenium,
Thanks for you time and suggestions! You helped alot! My layers panel was crazy. I re-arranged, re-organized and stacked according to the graphic. Solved my problem first try. Not used to making sure the order is right in illustrator, only in photoshop.
Thanks again man!
-NightRed

Pages is not saving document correctly. After saving the changes either do not appear or you can not open the file. The error is "not a valid format" I am in Pages '09 4.1 (923). I also use Parallels. Anyone having similar issues?

Pages is not saving document correctly. After saving the changes either do not appear or you can not open the file. The error is "not a valid format" I am in Pages '09 4.1 (923). I also use Parallels. Anyone having similar issues?

I'm not sure that Lion AutoSave feature apply to network servers.
I'm just sure that the Versions feature doesn't.
Yvan KOENIG (VALLAURIS, France) samedi 21 janvier 2012
iMac 21”5, i7, 2.8 GHz, 12 Gbytes, 1 Tbytes, mac OS X 10.6.8 and 10.7.2
My Box account is : http://www.box.com/s/00qnssoyeq2xvc22ra4k
My iDisk is : http://public.me.com/koenigyvan

What does it mean when you get a "The iTunes library file cannot be saved. There is not enought memory available." ? And what can I do to correct it?

What does it mean when you get a "The iTunes library file cannot be saved. There is not enought memory available." ? And what can I do to correct it?

Well, I installed the latest iTunes this AM, works perfectly. Although for some reason it did lock up after playing a song today.
Horror stories? That's a bit overly dramatic.
No, it isn't.
The issue you are experiencing is one that has occurred in multiple versions of iTunes, a simple search would have revealed this.
A simple search was conducted, no one seemed to have an answer. Do you always adopt such a haughty attitude? Or was I just lucky.

Hi, I've just downloaded the latest release 10.1.1 and now I do not see any more correctly my clips either in the canvas and in the timeline. Playing clips, they now appears with garbled images, completely unstables: I can not editing in these conditions!

Hi, I've just downloaded the latest release 10.1.1 and now I do not see any more correctly my clips either in the canvas and in the timeline. Playing clips, they now appears with garbled images, completely unstables: I can not editing in these conditions!
Anyone can help me?
Thank you, Claudio

Hi Russ, Thank you for your reply!
System Spec:
2x2.26 Ghz QUAD-CORE
12 GB RAM 1066 MHz DDR3
I've stored the library in HARD DISK which is installed inside my computer (1 TB capacity) and different from my hard disk in which I've installed all my applications (600 GB capacity).
I've installed FCP since 2001, bought FCP X in 2012: never had a problem. Yesterday I was editing my video of my last vacations (in California!) and I have updated FCP X, downloading FCP X 10.1.1: then the problem!
Strange is the fact that I've just tried to export a short project, I can see the final product quite well.
What is impossible is playing the clips within Final Cut: they are jumpimg, moving, presenting some frame in green or red ...
Everything all right in iMovie.
I've just checked the RAM: 9GB out of 12 GB is busy, could this be the problem?
Motion is very slow: for 20 sec of project, it takes minutes to play. And once again, if you finalize the projet and export it in Quicktime, you can see it correctly.
I do hope you may suggest something, I'm getting crazy!
Thank you in adavance
Claudio

Windows not scaling dpiAware programs correctly on high DPI screens

I just upgraded to a new notebook with a high dpi screen (3200x1800)..
In the standard desktop (not modern), several programs do not display correctly- specifically Adobe programs, Sony Vegas, Sorenson Squeeze, etc..
The type and fonts for the menus etc are scaled properly, but the UI icons are extremely tiny.
See here.. The red boxed areas are what size the icons SHOULD be:
http://tinypic.com/r/nb82l5/8
If I edit the manifest for each .exe and change
dpiAware to FALSE, everything scales fine but is blurry (sections inside red box from link above)
If dpiAware is already true in the program, why isn't windows scaling the program interface icons correctly?

Hi,
Please check and uncheck the following option to see the result.
Also,please use a external display device to test it.
Regards,
Kelvin Xu
TechNet Community Support

HT201401 My iphone will NOT unlock with my CORRECT passcode.

My iphone will NOT unlock with my CORRECT passcode. I can't even backup and restore on itunes because it's locked. What can I do? Does anyone have experience with this and know how to fix it?

If You Are Locked Out Or Have Forgotten Your Passcode
iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
iOS- Understanding passcodes
A Complete Guide to Recover Your iDevice if You Forget Your Passcode
If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
     1. Verify that you are using the latest version of iTunes before attempting to update.
     2. Connect your device to your computer.
     3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
     4. Select the Summary tab.
     5. Select the Restore option.
     6. When prompted to back up your settings before restoring, select the Back Up
         option (see in the image below). If you have just backed up the device, it is not
         necessary to create another.
     7. Select the Restore option when iTunes prompts you (as long as you've backed up,
         you should not have to worry about restoring your iOS device).
     8. When the restore process has completed, the device restarts and displays the Apple
         logo while starting up:
           After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
          to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
          iOS, keep your device connected until the "Connect to iTunes" screen goes away or
          you see "iPhone is activated."
     9. The final step is to restore your device from a previous backup.
If you can not restore your device then you will need to go to recovery mode.
Placing your device into recovery mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
     1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the other end
         of the cable connected to your computer's USB port.
     2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the
         red slider appears, then slide the slider. Wait for the device to turn off.
          If you cannot turn off the device using the slider, press and hold the Sleep/Wake
          and Home buttons at the same time. When the device turns off, release the Sleep/Wake
          and Home buttons.
     3. While pressing and holding the Home button, reconnect the USB cable to the device.
         The device should turn on. Note: If you see the screen pictured below, let the device
         charge for at least ten minutes to ensure that the battery has some charge, and then
         start with step 2 again.
     4. Continue holding the Home button until you see the "Connect to iTunes" screen.
         When this screen appears you can release the Home button.
     5. If necessary, open iTunes. You should see the following "recovery mode" alert:
     6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Additional Information:
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

The XI does not send messages with correct IDOC structure

SAP XI 3.0 sends to ECC IDOC HRMD_A07
The XI does not send messages with correct IDOC structure.
In XI Design, Software Component RHEVOLU, Ive imported the Objects
HRMD_A.HRMD_A07 from SAP ECC; In Tools -> Export Reduced XSD, I saved
HRMD_A.HRMD_A07.xsd in Namespace http://suezambiental.com.br/HR . At
Message Mapping -> mmAdmissao, in Imported Message -> Import XML or
XSD, I imported the reduced Idoc file generated above, mapping source
fields to target fields.
The IDOC sent from XI to ECC has this structure (template: 22122)
E1PLOGI
E1PORIG
E1PITYP
E1P0000
E1P0001
E1P0002
Status 53 -HR: ALE inbound processing for HR master data
But does not update HR Master data.
The structure expected in ECC side (template: 20376) is:
E1PLOGI
E1PORIG
E1PITYP
E1P0000
E1PITYP
E1P0001
E1PITYP
E1P0002
Status 53 -HR: ALE inbound processing for HR master data
By using WE19 transaction, this structure was changed manually; so, the
HR Master data was updated.
Witch kind of customizing or correction could be made in XI, to send
the correct structure to ECC?
Best Regards
Claudio

Hi Claudio,
In your case, there are perhaps two causes:
1. perhaps when you have import the idoc, for a strange reason, a bad metadata was created by XI. You can clean this one in tcode <b>IDX2</b> (Idoc metadata cache).
2. but it's also probably an error in your Message Mapping. Have you correctly manage segment E1PITYP?
Regards
Mickael

OSS note 1044741 contains no correction instructions for 46C.

I am trying to apply OSS note 1044741 to fix BC Set creation for deleted table entries. However OSS note 1044741 contains no correction instructions for 46C. Please provide assistance.
Bruce Reeves

Dear Bruce,
How to raise an OSS note:
In service.sap.com, choose Keys and Requests -> Development Requests -> Create Development Request
The Create development request form appears. It is divided into the sections described below:
Classification
In the 'Classification' section of the form, you can classify your request by selecting various criteria from the listboxes. This information is used for reporting purposes and to assign your request to a processor at SAP.
Reporting unit is only displayed for information. It defines if you enter the request for yourself, on behalf of a Customer Competence Center (CCC), of a customer, or of a user group. Which entries are available depends on the organization you are working for.
Priority defines the priority this request has for you.
Industry is only displayed for information. This is the industry of your company.
Other Industry allows you to select further industries if the request refers not only to your industry. To select more than one industry, hold down the <Ctrl> key and select the desired items by clicking on them.
Component defines the application component to which your request applies.
Core release defines the R/3 release you are currently working with.
Add-on defines, in case the request applies to an industry solution, the specific add-on release you are currently working with.
General provides generic features for a better classification of your request. If you wish to define more than one category, hold down the <Ctrl> key and select the desired items by clicking on them.
Cross-component provides cross-component features for a better classification of your request. If you wish to define more than one application, hold down the <Ctrl> key and select the desired items by clicking on them.
Only relevant for country allows you to specify that your request is only relevant for the selected country.
Personal classification by requestor
In the 'Personal classification by requestor' section, you can add your own classification criteria to the request:
Classification 1 - 3: allows you to specify your own features, e.g., "Project xyz". You can enter any text up to 30 characters in these fields.
Description
In the Description section of the form, you can describe in detail the feature you request for the SAP software.
In the Language field, select the language in which you are describing your request. For processing at SAP, all non-English requests will be translated into English.
In the Short text field, enter a meaningful title for your request.
The Long text field is mandatory. Use it to describe your request in detail. Even if you attach external description files, please enter a detailed description here.
The Business need field is mandatory. Please use it to explain why the requested feature is needed for your business.
The Example field is collapsed by default. Click on the plus symbol to the left of the field to expand the entry field, and enter an example for the requested feature.
The Current workaround field is collapsed by default. Click on the plus symbol to the left of the field to expand the entry field, and describe which procedure you currently use instead of the requested feature.
The Proposed solution field is collapsed by default. Click on the plus symbol to the left of the field to expand the entry field, and describe how you propose to solve the issue related to your request.
Attaching documents
You can also attach files that further describe your request, for example, documents or presentations. All file types supported by this site can be attached, this includes all popular Office formats.
To be able to attach files to your request, you must have the Check In Wizard program installed on your computer. Otherwise, an error message will be displayed. If you do not have the Check In Wizard installed, click here to start the installation
NOTE:
This will automatically save your request with the status New. The request will, however, not yet be sent to SAP. If you have not yet filled in all required fields, the system will prompt you to do so before you can add an attachment. The attachments will be listed only after you have saved or sent the request.
To attach a file, choose Add attachment.
The Check in Files dialog box appears.
Select the file you want to attach, and choose Open.
A status dialog box appears. When the status The check in process has completed successfully is displayed, confirm with OK.
The file is now attached to the development request.
Repeat the above steps for any additional files, if required.
Saving the development request
When you have entered all required data you can save your request. To do this, choose Save. You can then edit the request and send it to SAP later. This allows a company or user group to internally manage, discuss and consolidate its development requests before it decides which development requests will be sent to SAP in the next step. (Development requests that are no longer relevant can be set to status Closed by author).
Sending the development request to SAP
When you have entered all required data, you can alternatively send the request to SAP immediately. To do this, choose Sent to SAP. You need a special authorization to use this function. If you had saved a request before but not yet sent it to SAP, you can send it to SAP later using this function.
Resetting the request form
If you make a mistake during data entry and want to reset all entries to the values they had when you opened the form, choose the Reset button.
Closing the request
If you find that you no longer need the request, you can close it. In this way, you specify that no further processing of the request is necessary.
To close the request, choose Closed by author.
(After closing, confirm the request to remove it from your inbox.)
Confirming the request
Confirm the request if you have received SAP's final decision. The development request will no longer be shown in your Inbox.
To confirm the request, choose Confirm.
You will find the answers in your SAP inbox.
Visit the following link for information regarding SAP Notes:
http://help.sap.com/saphelp_nw04/helpdata/en/b8/3cf839fd35384de10000000a11402f/frameset.htm
Hope this will help.
Regards,
Naveen.

I have iTunes 10.5 and a 4g iPod touch. WHen I upgraded to 5.01, my photos are not all in the correct folders. Any ideas?

When I load my photos on my 4g ipod touch with iOS 5.01, the photos are there but not all in the correct folders. How can I correct that?

I spent last week looking for a solution to that little yellow "!" needle haystack....
It is probably buried where nothing can touch or change it other than what I resorted to and would have saved time, clean install after I made sure to have two backup sets: Windows Easy Transfer plus Paragon clone OS and partitions to drive. Had to spend a full day reinstalling, updates, etc. Careful not to bring back any prefs or data that might be corrupt or wrong.
10.5 and iOS 5 on new iPod 4G works much better though and as they should and no issues like I had with AMS or other services or needing to restart first before launching iTunes.

790FX-GD70 not setting RAM to correct timing nor voltage from SPED

My 790FX-GD70 not setting RAM to correct timing nor voltage from SPED when set to auto. The RAM I have should be 6 6 6 20 @ 1.8V but the motherboard is setting it to 9 9 9 24 @ 1.5 V
The RAM is Crucial 2GB, Ballistix 240-pin DIMM, DDR3 PC3-10600 memory BL25664BA1336 • DDR3 PC3-10600 • 6-6-6-20 • Unbuffered • NON-ECC • DDR3-1333 • 1.8V • 256Meg x 64 of which i have two of then in the two black slots.
Just to rule out the RAM I also tried a different model of RAM whose timing is 7 7 7 24 @ 1.65 which will not allow to boot to windows unless I adjust the voltage manually to 1.70 (1.65 V will still not boot properly) it sets it also at 9 9 9 24 yet this same sticks of RAM will set correctly in a MSI 770 C45 without any adjustments.
Now i will say in the case of the 790FX-GD70 I require no changes in voltage for it to boot with the 1.8 V RAM just the timings are not as they should be. The 790FX-GD70 is stable as is and I will probably leave it at the auto settings but wondered if anyone else encountered similar issues with this board

Looks like this is a bit of an issue for some other users of your RAM and not necessarily a MSI thing! This user has a ASUS board! Good luck and hope you get it sorted out.
Backround:
I bought some DDR3-1333 ram that was advertised as 6-6-6-20 @ 1.8v and, as expected, running on my board's default 1.5v it was only getting like 9-9-9-24. In fact, @ stock voltage the best I could boot up with (unknown stability) was 9-7-7. In an attempt to get the best (advertised?) performance I went ahead and manually set the timings to 6-6-6-20, left all other timings on auto, and upped the voltage to 1.8v
Boots up fine and appears to be stable. However, I do notice the RAM is fairly warm to the touch whereas @ 1.5v it was pretty benign heat-wise. I tried running 1.785v but 3 out of 4 times it would hang on the windows desktop display. So I bumped it back up to 1.8v and I'll run Memtest 86 or something else later tonight.
My question, being a noob and all...
Is running at 1.8v going to hurt something? (See my setup MB, and CPU stats)
Just to repeat, the box and manufacturer do list it as 1.8v spec. (FYI: BL25664BA1336)

Red eye correction not saving, Red eye correction not saving

Similar Messages

Maybe you are looking for