Remote Access VPN on Cisco ASA Problem

Hi, i configured Remote access VPN on Cisco ASA 8.x as per below configuration.
Problem is that my internet has stopped working, and default route is just showing stars.
i can ping internal server 10.110.10.150 fine , which i allowed on VPN ACL, but my other traffic not going to regular internet on my laptop,
what additional required to force my internet to go to regular internet instead of getting encrypted?
Also attaching output of route print at the point when VPN is connected.
ip local pool RA_VPN_POOL 10.1.200.100-10.1.200.150 mask 255.255.255.0
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto dynamic-map RA_VPN 65535 set transform-set ESP-AES-128-SHA
crypto dynamic-map RA_VPN 65535 set security-association lifetime seconds 28800
crypto dynamic-map RA_VPN 65535 set security-association lifetime kilobytes 4608000
crypto map VPN_MAP 65535 ipsec-isakmp dynamic RA_VPN
crypto map VPN_MAP interface outside
isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
tunnel-group ITT_RA type remote-access
tunnel-group ITT_RA general-attributes
address-pool RA_VPN_POOL
default-group-policy RA_VPN_GP
tunnel-group ITT_RA ipsec-attributes
pre-shared-key <group key>
group-policy RA_VPN_GP internal
group-policy RA_VPN_GP attributes
dns-server value 10.0.0.1 10.0.0.2
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Split_Tunnel_List
default-domain value mydomain.com
address-pools value RA_VPN_POOL
access-list Split_Tunnel_List extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
access-list nonattest extended permit ip host 10.110.10.150 10.1.200.0 255.255.255.0
nat (inside) 0 access-list nonattest
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface Metric
          0.0.0.0          0.0.0.0      10.111.36.1      10.111.36.9          276
          0.0.0.0          0.0.0.0         On-link      10.1.200.100            20
       10.1.200.0    255.255.255.0         On-link      10.1.200.100    276
     10.1.200.100 255.255.255.255         On-link      10.1.200.100    276
     10.1.200.255 255.255.255.255         On-link      10.1.200.100    276
    10.110.10.150 255.255.255.255       10.1.200.1     10.1.200.100    100
      10.111.36.0    255.255.255.0         On-link       10.111.36.9    276

Similar Messages

Remote access VPN with Cisco Router - Can not get the Internal Lan .

Dear Sir ,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .Please see the attachment for Scenario, Configuration and Ping status.
I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Below is the IP address of the device.
Local PC connect with Router -2 (Through MS Loopback) Router -2 Router-1 PC -01
IP Address :10.10.10.2 Mask : 255.255.255.0 F0/01
IP address:10.10.10.1
Mask:255.255.255.0 F0/0
IP Address :20.20.20.1
Mask :255.255.255.0
F0/1
IP address :192.168.1.3
Mask:255.255.255.0
F0/0
IP address :20.20.20.2
Mask :255.255.255.0
F0/1
IP address :192.168.1.1
Mask:255.255.255.0
I can ping from local PC to the network 10.10.10.0 and 20.20.20.0 .Please find the attach file for ping status .So connectivity is ok from my local PC to Remote Router 1 and 2.
Through Cisco remote vpn client, I can get connected with the VPN Router R1 (Please see the VPN Client pic.)But cannot ping the network 192.168.1.0
Need your help to fix the problem.
Router R2 Configuration :!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R2
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
ip tcp synwait-time 5
interface FastEthernet0/0
ip address 20.20.20.2 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 10.10.10.1 255.255.255.0
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
login
end
Router R1 Configuration :
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
aaa new-model
aaa authentication login USERAUTH local
aaa authorization network NETAUTHORIZE local
aaa session-id common
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
username vpnuser password 0 strongpassword
ip tcp synwait-time 5
crypto keyring vpnclientskey
pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp client configuration group remotevpn
key cisco123
dns 192.168.1.2
wins 192.168.1.2
domain mycompany.com
pool vpnpool
acl VPN-ACL
crypto isakmp profile remoteclients
description remote access vpn clients
keyring vpnclientskey
match identity group remotevpn
client authentication list USERAUTH
isakmp authorization list NETAUTHORIZE
client configuration address respond
crypto ipsec transform-set TRSET esp-3des esp-md5-hmac
crypto dynamic-map DYNMAP 10
set transform-set TRSET
set isakmp-profile remoteclients
crypto map VPNMAP 10 ipsec-isakmp dynamic DYNMAP
interface FastEthernet0/0
ip address 20.20.20.1 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map VPNMAP
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
ip local pool vpnpool 192.168.50.1 192.168.50.10
ip forward-protocol nd
ip route 10.10.10.0 255.255.255.0 FastEthernet0/0
no ip http server
no ip http secure-server
ip nat inside source list NAT-ACL interface FastEthernet0/0 overload
ip access-list extended NAT-ACL
deny ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
permit ip 192.168.1.0 0.0.0.255 any
ip access-list extended VPN-ACL
permit ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
end

Dear All,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .
Please see the attachment for Scenario, Configuration and Ping status. I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Waiting for your responce .
--Milon

Remote access vpn on cisco 866VAE-k9

Hi All,
I need to create a remote access vpn tunnel to a cisco 866VAE-k9 (interfaceport GE0).
i have tried multiple configuration options like i found them in the documentation, but wasn't able to get it to work.
the current setup is:
866VAE-k9 LAN ip: 192.168.178.1, public ip: 83.xx.xx.xx
remote pc local ip: 192.168.178.x, public ip: 90.xx.xx.xx
the current vpn configuration (not working) is:
aaa authentication login userauthen local
aaa authorization network groupauthor local
username user password 0 secret
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
sh run
crypto isakmp client configuration group vpnclient
key vpnkey
domain xxx.local
pool ippool
acl 101
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map clientmap client authentication list userauthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
interface gigabitethernet0/0
ip address 83.xx.xx.xx 255.255.255.0
ip nat outside
crypto map clientmap
ip local pool ippool 192.168.178.93 192.168.178.94
ip nat inside source list 111 interface GigabitEthernet0/0 overload
access-list 111 deny ip 192.168.178.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 111 permit ip any any
access-list 101 permit ip 192.168.178.0 0.0.0.255 192.168.1.0 0.0.0.255
What should i do to get a working vpn tunnel?

Hi David Castro,
Thanks for your answer,
I configed following your guide, but it have not worked yet. I saw that I cannot ping IP gateway Internet . I using ADSL Internet and config PPPoE and my router receive IP from ISP. Here show ip int brief :
GigabitEthernet0/0         192.168.1.1     YES NVRAM up                    up
GigabitEthernet0/1         unassigned      YES NVRAM up                    up
GigabitEthernet0/2         unassigned      YES NVRAM up                    up
Dialer1                    210.245.54.49   YES IPCP   up                    up
Dialer2                    101.99.7.73     YES IPCP   up                    up
NVI0                       192.168.1.1     YES unset up                    up
Virtual-Access1            unassigned      YES unset up                    up
Virtual-Access2            unassigned      YES unset up                    up
Virtual-Access3            unassigned      YES unset up                    up
But I cannot ping Interface Dialer 1, so may be VPN is does not worked. Do you have some ideal ?
Thanks very much !

Help with Remote access VPN on Cisco router 3925 via Dialer Interface

Hi Everybody,
I need help for my work now, I appreciate if someone can fix my problem.I have a Cisco router 3925 and access Internet via PPPoE link. I want config VPN Remote Access and using software Cisco VPN client. But it doesn't work.. Here my config router :
HUNRE#show running-config
Building configuration...
Current configuration : 5515 bytes
! No configuration change since last restart
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname HUNRE
boot-start-marker
boot-end-marker
enable secret 5 $1$vEFw$rLfvLglzUgddCVwXDx03K.
enable password cisco
aaa new-model
aaa session-id common
crypto pki trustpoint TP-self-signed-1050416327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1050416327
revocation-check none
rsakeypair TP-self-signed-1050416327
crypto pki certificate chain TP-self-signed-1050416327
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31303530 34313633 3237301E 170D3134 30393235 31313534
31395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30353034
31363332 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CC79 74FCFABE 81183B70 5A9F4A53 EB609754 7D5F8587 9150B76E 3207A86E
5B65F9E9 6CDAC21A 6D69221D 1FF61632 14763308 43B2A1CC 8EE5ABAC EF07530E
3F0D35FE F08C955B 60B52B92 F8F54D53 DD6DD623 01F83493 02F9C49A F0C3483D
3B48A008 8D96700E 88924BFE DE00201B DE5965DE 32898CAD 9012AB55 76B6F39B
2D470203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14C3418C BC35F3D9 B26B2475 2BB5F826 060525AB B3301D06
03551D0E 04160414 C3418CBC 35F3D9B2 6B24752B B5F82606 0525ABB3 300D0609
2A864886 F70D0101 05050003 81810070 AC7C26C6 4606A551 1A3FD6C5 2A5AEAE8
35DAC86E F8885E26 51F6EEAE 7565D3AA D532C8F3 55F6656F D103F38C 8FBDE7F1
83E77143 76469040 7FEA41E8 14963DB3 F7F28EA0 C5F2F42C B186B75C AAB04900
15F9CB38 A16964F5 4E7B4378 35041AA8 AE8EC181 D58D6A62 676E286A 7B9D80E6
35A0B9FB FB76E976 3D2A19D7 006078
        quit
ip name-server 210.245.1.253
ip name-server 210.245.1.254
ip cef
no ipv6 cef
multilink bundle-name authenticated
vpdn enable
vpdn-group 1
vpdn-group 2
license udi pid C3900-SPE100/K9 sn FOC1823839B
license boot module c3900 technology-package securityk9
username cisco privilege 15 secret 5 $1$aAjB$D3iLyPFTE7O1bHPnKSJcH0
username kdhong privilege 15 secret 5 $1$nfyX$FO1BPTabCUaE6uKQwpLT.1
redundancy
track 1 ip sla 1 reachability
track 2 ip sla 2 reachability
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group VPN-HUNRE
key hunre
dns 8.8.8.8
domain hunre
pool IP-VPN
acl 199
max-users 100
crypto ipsec transform-set encrypt-method-1 esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map DYNMAP 1
set transform-set encrypt-method-1
crypto map VPN client configuration address respond
crypto map VPN 65535 ipsec-isakmp dynamic DYNMAP
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip mtu 1492
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
interface GigabitEthernet0/1
description FPT
no ip address
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface GigabitEthernet0/2
description Connect to CMC
no ip address
ip mtu 1442
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
no cdp enable
interface Dialer1
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp dns request
crypto map VPN
interface Dialer2
description Logical ADSL Interface 2
ip address negotiated
ip mtu 1442
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1344
dialer pool 2
dialer-group 2
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp address accept
no cdp enable
ip local pool IP-VPN 10.252.252.2 10.252.252.245
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 10 interface Dialer1 overload
ip nat inside source list 11 interface Dialer2 overload
ip nat inside source static 10.159.217.10 interface Dialer1
ip nat inside source list 199 interface Dialer1 overload
ip nat inside source static tcp 10.159.217.10 80 210.245.54.49 80 extendable
ip nat inside source static tcp 10.159.217.10 3389 210.245.54.49 3389 extendable
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.159.217.0 255.255.255.0 192.168.1.8
ip sla auto discovery
ip sla responder
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
access-list 10 permit any
access-list 11 permit any
access-list 101 permit icmp any any
access-list 199 permit ip any any
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
transport input all
line vty 5 15
password cisco
transport input all
scheduler allocate 20000 1000
ntp master
end
However, I cannot ping interfac Dialer 1. I using Cisco vpn client software ver 5.0.07.0290.
Hopeful for your answers !
Thanks

Hi David Castro,
Thanks for your answer,
I configed following your guide, but it have not worked yet. I saw that I cannot ping IP gateway Internet . I using ADSL Internet and config PPPoE and my router receive IP from ISP. Here show ip int brief :
GigabitEthernet0/0         192.168.1.1     YES NVRAM up                    up
GigabitEthernet0/1         unassigned      YES NVRAM up                    up
GigabitEthernet0/2         unassigned      YES NVRAM up                    up
Dialer1                    210.245.54.49   YES IPCP   up                    up
Dialer2                    101.99.7.73     YES IPCP   up                    up
NVI0                       192.168.1.1     YES unset up                    up
Virtual-Access1            unassigned      YES unset up                    up
Virtual-Access2            unassigned      YES unset up                    up
Virtual-Access3            unassigned      YES unset up                    up
But I cannot ping Interface Dialer 1, so may be VPN is does not worked. Do you have some ideal ?
Thanks very much !

Remote access VPN-unable to connect inside-URGENT

Hi,
I have configured Remote access VPN in cisco ASA 5520.Whenever I am trying to connect from outside it's connecting fine.It aslo getting IP from pool but prob is i am unable to connect/ping inside nw.
Pls help me...how to resolve this issue.

I had the same problem on an IOS router (871). My solution was one of two things. I downloaded the most up-to-date version of the VPN client (5.0.02.90) as opposed to the version I had or it was a software firewall (Norton 360). I have two different computers. One works just fine...the other connects but no traffic passes through. Here is what I have:
Computer 1 (working)- VPN Client v5.0.02.0090 and Network Associates Enterprise VirusScan.
Computer 2 (not working) - VPN Client v5.0.00.0340 and Norton 360.
I highly doubt it is the VPN Client, but sometimes you never know. Check your software firewall and try disabling it. Let me know how this works.

Remote Access VPN, how to specify on which interface clients will be placed on?

Hi,
I have a general understanding problem with remote access VPN and Cisco ASA.
If I have an ASA with multiple interfaces and I want to make sure that a Remote Access VPN Client is placed onto a specific interface, how do I do this?
example:
ASA has 4 interfaces: outside, inside-clients, inside-workers, inside-lab.
I want to allow multiple Remote Access VPN configurations that put clients coming from "outside" to "inside-lab" and "inside-clients", with two different profiles and two different IP pools, as the IP addresses for each of the interfaces is different.
How do I do that?
If possible be as explanatory as possible for me to really grasp the concept.
Many thanks
Pat

Hi,
The ASA will view the hosts in its routing table behind the ASA interface which forms the VPN connection with the VPN Client. This is most of the time the interface called "outside".
By default the ASA allows all traffic coming from a VPN connection to bypass the interface ACL of the ASA. The thought process behind this is I guess the fact that the VPN devices/clients have already proven they have right to connect to the network to all traffic is allowed.
The configuration that controls this setting globally on the ASA is
sysopt connection permit-vpn
The above is the default setting of the command and it WONT show up in the CLI format configurations because its a default setting.
If you were to issue the following command
no sysopt connection permit-vpn
Then this would mean that the ASA would require an ACL statement on its VPN terminating interface (outside) to permit the traffic from the VPN Pool to the LAN networks.
Naturally you would have to take into consideration also that if you have existing VPNs and insert the above global command they would also need ACL statements on the "outside" interface ACL or the inbound traffic from the VPN will start to get blocked.
Other option (wihtout touching the above setting) would be to configure VPN Filter ACL that is a separate ACL that is only attached to a certain user or group of users.
I personally prefer the method of using the above global setting and using the "outside" interface ACL to control traffic.
Naturally it still leaves the question of how you are going to configure the Tunnel Groups, Group Policys and Usernames. To be honest, I have gotten a bit distracted from VPN client setups and have forgotten a lot of stuff since I dont work with them on a day to day basis. I mostly handle L2L VPN nowadays among normal firewall configurations.
If I had to suggest something simple at this point it would be this
Configure separate Tunnel Groups
Configure separate VPN Pools for the above Tunnel Groups
Configure separate Group Policys for the above Tunnel Groups
Configure the above mentioned Global setting to limit inbound traffic from VPN
Configure the "outside" interface ACL so that you only permit traffic from a certain VPN Tunnel Group users only to certain LAN networks
Configure the required NAT0 configurations for traffic between these networks
As Marcin said, there are multiple different ways to achieve the same thing as above.
And as I said I have gotten a bit rusty with the VPN Client side on the ASA so I am not sure if at the moment I can even consider all the possible options but surely the simple ones.
PS. The link that Marcin posted seems to point to a Group Policy setting that would let you lock the that VPN connection to use only a certain local Vlan (subinterface) on the ASA and therefore limit traffic from going to networks behind other interfacec
Hope this helps
- Jouni

Remote Access VPN ASA

Hi Guys
I have a problem with a Remote Access VPN on a ASA 5510 8.6.2
I have created a IPSEC Remote Access VPN through the wizard this is pretty much a base install on the ASA without much configuration.
I can connect to the ASA via the Remote Access client and get TX just no RX therefore i cannot access any of the LAN resources
here is a copy of the config any help would be appreciated.
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.252
interface Management0/0
nameif management
security-level 100
ip address 10.2.1.252 255.255.240.0
management-only
ftp mode passive
dns server-group DefaultDNS
domain-name perfectdomain.perfect-image.co.uk
same-security-traffic permit inter-interface
object network Inside-Network
subnet 10.2.0.0 255.255.240.0
description Inside Network
object network NETWORK_OBJ_192.168.1.0_27
subnet 192.168.1.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object-group network LOCAL_NETWORKS_VPN
access-list inside_access_in extended permit ip object NETWORK_OBJ_192.168.1.0_24 any
access-list outside_access_in extended permit ip object NETWORK_OBJ_192.168.1.0_24 object Inside-Network
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool RAIPSECPOOL 192.168.1.1-192.168.1.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside,outside) source static Inside-Network Inside-Network destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static Inside-Network Inside-Network no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable 4430
http 10.2.0.0 255.255.240.0 management
http 10.2.0.0 255.255.240.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 10.2.0.0 255.255.240.0 inside
telnet timeout 5
ssh 10.2.0.0 255.255.240.0 management
ssh 10.2.0.0 255.255.240.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 10
console timeout 0
dhcpd address 10.2.1.253-10.2.2.252 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RAIPSECTUNNEL internal
group-policy RAIPSECTUNNEL attributes
dns-server value 10.2.1.7 10.2.1.8
vpn-tunnel-protocol ikev1
default-domain value perfectdomain.perfect-image.co.uk
username KI-Admin password OMa9XVzN1OQ0Is.6 encrypted privilege 15
username PI-Admin password BEGl74DXS9pqUL6v encrypted privilege 15
tunnel-group RAIPSECTUNNEL type remote-access
tunnel-group RAIPSECTUNNEL general-attributes
address-pool RAIPSECPOOL
default-group-policy RAIPSECTUNNEL
tunnel-group RAIPSECTUNNEL ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:43c49a676e839e7821ff1473ddeaf90d
: end
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.252
interface Management0/0
nameif management
security-level 100
ip address 10.2.1.252 255.255.240.0
management-only
ftp mode passive
dns server-group DefaultDNS
domain-name perfectdomain.perfect-image.co.uk
same-security-traffic permit inter-interface
object network Inside-Network
subnet 10.2.0.0 255.255.240.0
description Inside Network
object network NETWORK_OBJ_192.168.1.0_27
subnet 192.168.1.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object-group network LOCAL_NETWORKS_VPN
access-list inside_access_in extended permit ip object NETWORK_OBJ_192.168.1.0_24 any
access-list outside_access_in extended permit ip object NETWORK_OBJ_192.168.1.0_24 object Inside-Network
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool RAIPSECPOOL 192.168.1.1-192.168.1.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside,outside) source static Inside-Network Inside-Network destination static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static Inside-Network Inside-Network no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable 4430
http 10.2.0.0 255.255.240.0 management
http 10.2.0.0 255.255.240.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 10.2.0.0 255.255.240.0 inside
telnet timeout 5
ssh 10.2.0.0 255.255.240.0 management
ssh 10.2.0.0 255.255.240.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 10
console timeout 0
dhcpd address 10.2.1.253-10.2.2.252 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RAIPSECTUNNEL internal
group-policy RAIPSECTUNNEL attributes
dns-server value 10.2.1.7 10.2.1.8
vpn-tunnel-protocol ikev1
default-domain value perfectdomain.perfect-image.co.uk
username KI-Admin password OMa9XVzN1OQ0Is.6 encrypted privilege 15
username PI-Admin password BEGl74DXS9pqUL6v encrypted privilege 15
tunnel-group RAIPSECTUNNEL type remote-access
tunnel-group RAIPSECTUNNEL general-attributes
address-pool RAIPSECPOOL
default-group-policy RAIPSECTUNNEL
tunnel-group RAIPSECTUNNEL ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:43c49a676e839e7821ff1473ddeaf90d
: end

Hi Jouni
Still not working I am afraid, here is the current running config, I have noticed when I connect via VPN client the default gateway address on the VPN client is 192.168.1.2 ?? anymore help would be appreciated
thank you
hostname PIFW01
domain-name perfectdomain.perfect-image.co.uk
enable password pBWHd.sDdzPIDYW/ encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0/0
nameif inside
security-level 100
ip address 10.2.1.251 255.255.255.0
interface GigabitEthernet0/1
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
nameif outside
security-level 0
ip address 212.135.154.130 255.255.255.252
interface Management0/0
nameif management
security-level 100
ip address 10.2.1.252 255.255.240.0
management-only
ftp mode passive
dns server-group DefaultDNS
domain-name perfectdomain.perfect-image.co.uk
same-security-traffic permit inter-interface
object network Inside-Network
subnet 10.2.0.0 255.255.240.0
description Inside Network
object network NETWORK_OBJ_192.168.1.0_27
subnet 192.168.1.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network VPNPool
subnet 192.168.1.0 255.255.255.0
description VPNPool
object network VPN-POOL
subnet 192.168.1.0 255.255.255.0
object network LAN
subnet 10.2.1.0 255.255.255.0
access-list inside_access_in extended permit ip object LAN any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool RAIPSECPOOL 192.168.1.1-192.168.1.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside,outside) source static LAN LAN destination static VPN-POOL VPN-POOL
nat (inside,outside) after-auto source dynamic any interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 212.135.154.129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable 4430
http 10.2.0.0 255.255.240.0 management
http 10.2.0.0 255.255.240.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 10.2.0.0 255.255.240.0 inside
telnet timeout 5
ssh 10.2.0.0 255.255.240.0 management
ssh 10.2.0.0 255.255.240.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 10
console timeout 0
dhcpd address 10.2.1.253-10.2.2.252 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RAIPSECTUNNEL internal
group-policy RAIPSECTUNNEL attributes
dns-server value 10.2.1.7 10.2.1.8
vpn-tunnel-protocol ikev1
default-domain value perfectdomain.perfect-image.co.uk
username KI-Admin password OMa9XVzN1OQ0Is.6 encrypted privilege 15
username PI-Admin password BEGl74DXS9pqUL6v encrypted privilege 15
tunnel-group RAIPSECTUNNEL type remote-access
tunnel-group RAIPSECTUNNEL general-attributes
address-pool RAIPSECPOOL
default-group-policy RAIPSECTUNNEL
tunnel-group RAIPSECTUNNEL ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f50aaad7c3ecaf94382ff0cc887bb5ac
: end

Remote Access VPN Query

Hi All,
I'm looking to setup a Remote Access VPN via my ASA 5510. The clients will be using Cisco Anyconnect (which I assume is compatible...?) When I use the wizard it only mentions Cisco VPN Client.
When my clients connect up to the ASA via Anyconect, can I get them to just use DHCP via my AD servers or do I need to configure a seperate independent scope specifically for VPN clients?
Thanks

Hi Grant,
When you configure Remote access VPN , you need to configure a seprated pool of ip address for the vpn user.
Regards,
Bikas R.Pandey.

Remote access VPN on ASA5520 Ping Issues.

Hi I hope someone might be able to help me. I have setup a remote access VPN on an ASA 5520. The VPN client connects ok, accepts my username and password and then I am in. I get an allocated IP address of 172.16.1.1 from the local pool. The problem is that I cannot then ping the inside LAN which is 192.168.1.1. I've got isakmp nat traversal set to default which is 20. I've been looking at this all day and I think I've gone crossed eyed, a fresh pair of eyes are definitley required, so any help would be gratefully received. My config is
Saved
ASA Version 7.0(8)
hostname Hospira-firewall
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
dns-guard
interface GigabitEthernet0/0
speed 100
duplex full
nameif outside
security-level 0
ip address 213.212.66.52 255.255.255.248
interface GigabitEthernet0/1
speed 100
duplex full
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
ftp mode passive
same-security-traffic permit intra-interface
access-list NONAT extended permit ip 192.168.1.0 255.255.255.0 172.16.1.0 255.255.255.0
access-list Split standard permit 192.168.1.0 255.255.255.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip local pool mypool 172.16.1.1-172.16.1.253 mask 255.255.255.0
no failover
asdm image disk0:/asdm-508.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list NONAT
nat (inside) 1 192.168.1.0 255.255.255.0
route outside 0.0.0.0 0.0.0.0 213.212.66.49 1
route outside 172.16.1.0 255.255.255.0 213.212.66.49 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00
timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
group-policy hospira internal
group-policy hospira attributes
vpn-simultaneous-logins 400
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Split
webvpn
username user password 08S9WUsiSMr3RauN encrypted
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set hospira esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map dmap 1 set transform-set hospira
crypto dynamic-map dmap 1 set security-association lifetime seconds 28800
crypto dynamic-map dmap 1 set security-association lifetime kilobytes 4608000
crypto dynamic-map dmap 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dmap
crypto map mymap 2 match address NONAT
crypto map mymap 2 set security-association lifetime seconds 28800
crypto map mymap 2 set security-association lifetime kilobytes 4608000
crypto map mymap interface outside
isakmp identity address
isakmp enable outside
isakmp policy 1 authentication pre-share
isakmp policy 1 encryption 3des
isakmp policy 1 hash sha
isakmp policy 1 group 2
isakmp policy 1 lifetime 86400
isakmp policy 65535 authentication pre-share
isakmp policy 65535 encryption 3des
isakmp policy 65535 hash sha
isakmp policy 65535 group 2
isakmp policy 65535 lifetime 86400
isakmp nat-traversal 20
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *
tunnel-group hospira type ipsec-ra
tunnel-group hospira general-attributes
address-pool mypool
default-group-policy hospira
tunnel-group hospira ipsec-attributes
pre-shared-key *
telnet timeout 5
ssh timeout 5
console timeout 0
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect dns maximum-length 512
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp
inspect icmp error
service-policy global_policy global
Cryptochecksum:98f85c39a5cbffe66b0f6585d5083c7c
: end
Many thanks

Hi Richard ,
- we don't need access-list with RA connection , we have the dynamic map that acts as a template , so your crypto config :
crypto map mymap 1 ipsec-isakmp dynamic dmap
crypto map mymap 2 match address NONAT
crypto map mymap 2 set security-association lifetime seconds 28800
crypto map mymap 2 set security-association lifetime kilobytes 4608000
crypto map mymap interface outside
map with seq 1 is being binded to the dynamic map , now map 2 you are using the nonat access list as the encryption trigger for this map , so this should not be there as it encrypt traffic from the inside subnet to the pool .
please remove the second entry, then test if not working please provide a capture from the inside interface .
HTH
Mohammad.

Remote Access VPN Setup

Hello Support,
I have a question regarding a remote access VPN setup with the following. I have a Cisco 6500 with multiple VLANs, and an FWSM setup in mutliple context mode. Each of our clients sits behind their own context, and has their own associated VLANs. Each context has a shared interface, so that one network (our management network) can see all of the networks. We are using a Cisco ASA to terminate P2P VPNs as the FWSms cannot do so, but I would like to setup a remote access VPN from the ASA, but I will need to connect in and have access to all networks. Currently the ASA has an outside interface for internet, two client inside interfaces, and one interface on the shared network.
If I setup a remote access VPN from the ASA with a separate scope will I be able to see all the networks that I setup routes and nonats for or is there more to it?
I provided a brief diagram showing all the vlans, I will need to be able to access all of the 6500s vlans when connected using the VPN.
Thanks in advance for all ideas, suggestions, and assistance.

Hello John,
You will need to configure the respective IP Address pool for the Anyconnect users,
Then create the no_nat rules from all of the internal subnets to the Anyconnect Pool.
That should do it bud . I mean just make sure the internal network (core) knows that in order to reach the anyconnect pool must send the traffic to the ASA.
Rate all of the helpful posts!!!
Regards,
Jcarvaja
Follow me on http://laguiadelnetworking.com

Remote Access VPN Clients Cannot Access inside LAN

I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with. I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA. Thay can ping each other. The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10. I do not need split tunneling to be enabled. The active WAN interface is the one labeled outside_cable.
: Saved
ASA Version 8.2(1)
hostname ASA5505
domain-name default.domain.invalid
enable password eelnBRz68aYSzHyz encrypted
passwd eelnBRz68aYSzHyz encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.100.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group dataDSL
ip address 76.244.75.57 255.255.255.255 pppoe
interface Vlan3
nameif dmz
security-level 50
ip address 192.168.9.1 255.255.255.0
interface Vlan10
nameif outside_cable
security-level 0
ip address 50.84.96.178 255.255.255.240
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit intra-interface
object-group service Netbios udp
port-object eq 139
port-object eq 445
port-object eq netbios-ns
object-group service Netbios_TCP tcp
port-object eq 445
port-object eq netbios-ssn
object-group network DM_INLINE_NETWORK_1
network-object host 192.168.100.177
network-object host 192.168.100.249
object-group service Web_Services tcp
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
object-group network DM_INLINE_NETWORK_10
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_11
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_2
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_3
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_4
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_5
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_6
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_7
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_8
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_9
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network VPN
network-object 192.168.255.0 255.255.255.0
access-list outside_access_in extended permit icmp any host 76.244.75.61
access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp
access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp-data
access-list outside_access_in extended permit tcp any host 76.244.75.62 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.62 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.59 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.59 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.60 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.60 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.58 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.58 eq https
access-list dmz_access_in remark Quickbooks
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_6 host 192.168.100.5 eq 56719
access-list dmz_access_in remark Quickbooks range
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_7 host 192.168.100.5 range 55333 55337
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_8 host 192.168.100.5 eq 1434
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_9 host 192.168.100.5 eq 49398
access-list dmz_access_in remark QB
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_10 host 192.168.100.5 eq 8019
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_2 host 192.168.100.5 eq 2638
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_11 host 192.168.100.5 object-group Netbios
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_3 host 192.168.100.5 object-group Netbios_TCP
access-list dmz_access_in extended deny ip host 192.168.9.4 host 192.168.100.5 inactive
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_4 any
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_5 any
access-list dmz_access_in remark Printer
access-list dmz_access_in extended permit ip 192.168.9.0 255.255.255.0 object-group DM_INLINE_NETWORK_1
access-list dmz_access_in extended permit tcp 192.168.9.0 255.255.255.0 any object-group Web_Services
access-list dmz_access_in extended permit udp 192.168.9.0 255.255.255.0 any eq domain
access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.255.0 255.255.255.0 echo-reply
access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.100.0 255.255.255.0 echo-reply log disable
access-list dmz_access_in remark QB probably does not need any udp
access-list dmz_access_in extended permit udp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
access-list dmz_access_in remark QB included in other rule range
access-list dmz_access_in extended permit tcp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
access-list dmz_access_in remark May be required for Quickbooks
access-list dmz_access_in extended permit icmp host 192.168.9.4 host 192.168.100.5
access-list CAD_capture extended permit ip host 192.168.9.4 host 192.168.100.5
access-list CAD_capture extended permit ip host 192.168.100.5 host 192.168.9.4
access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 172.16.10.0 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 172.16.20.0 255.255.255.240
access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.100.0 255.255.255.0
access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.9.0 255.255.255.0
access-list dmz_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
access-list outside_cable_access_in extended permit icmp any host 50.84.96.182
access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp
access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp-data
access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq https
access-list Local_LAN_Access standard permit host 0.0.0.0
access-list vpnusers_spitTunnelACL extended permit ip 192.168.100.0 255.255.255.0 any
access-list nonat-in extended permit ip 192.168.100.0 255.255.255.0 172.16.20.0 255.255.255.0
pager lines 24
logging enable
logging buffered informational
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
mtu outside_cable 1500
ip local pool VPN_IP_range 192.168.255.1-192.168.255.10 mask 255.255.255.0
ip local pool VPN_Phone 172.16.20.1-172.16.20.10 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat-control
global (outside) 10 interface
global (outside_cable) 10 interface
nat (inside) 0 access-list nonat-in
nat (inside) 10 0.0.0.0 0.0.0.0
nat (dmz) 0 access-list dmz_nat0_outbound
nat (dmz) 10 0.0.0.0 0.0.0.0
static (inside,outside) 76.244.75.62 192.168.100.25 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.61 192.168.9.123 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.59 192.168.9.124 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.58 192.168.9.4 netmask 255.255.255.255 dns
static (inside,dmz) 192.168.100.0 192.168.100.0 netmask 255.255.255.0
static (dmz,outside) 76.244.75.60 192.168.9.10 netmask 255.255.255.255 dns
static (inside,outside_cable) 50.84.96.183 192.168.100.25 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.182 192.168.9.123 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.180 192.168.9.124 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.179 192.168.9.4 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.181 192.168.9.10 netmask 255.255.255.255 dns
access-group outside_access_in in interface outside
access-group dmz_access_in in interface dmz
access-group outside_cable_access_in in interface outside_cable
route outside_cable 0.0.0.0 0.0.0.0 50.84.96.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.100.0 255.255.255.0 inside
http 204.107.173.0 255.255.255.0 outside
http 204.107.173.0 255.255.255.0 outside_cable
http 0.0.0.0 0.0.0.0 outside_cable
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_cable_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_cable_map interface outside_cable
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp enable outside_cable
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet 192.168.100.0 255.255.255.0 inside
telnet timeout 5
ssh 192.168.100.0 255.255.255.0 inside
ssh 204.107.173.0 255.255.255.0 outside
ssh 204.107.173.0 255.255.255.0 outside_cable
ssh 0.0.0.0 0.0.0.0 outside_cable
ssh timeout 15
console timeout 0
vpdn group dataDSL request dialout pppoe
vpdn group dataDSL localname [email protected]
vpdn group dataDSL ppp authentication pap
vpdn username [email protected] password *********
dhcpd address 192.168.100.30-192.168.100.99 inside
dhcpd dns 192.168.100.5 68.94.156.1 interface inside
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.100.5
vpn-tunnel-protocol IPSec l2tp-ipsec
group-policy cad_supplies_RAVPN internal
group-policy cad_supplies_RAVPN attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value cad_supplies_RAVPN_splitTunnelAcl
group-policy VPNPHONE internal
group-policy VPNPHONE attributes
dns-server value 192.168.100.5
vpn-tunnel-protocol IPSec
split-tunnel-policy excludespecified
split-tunnel-network-list value Local_LAN_Access
client-firewall none
client-access-rule none
username swinc password BlhBNWfh7XoeHcQC encrypted
username swinc attributes
vpn-group-policy cad_supplies_RAVPN
username meredithp password L3lRjzwb7TnwOyZ1 encrypted
username meredithp attributes
vpn-group-policy cad_supplies_RAVPN
service-type remote-access
username ipphone1 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone1 attributes
vpn-group-policy VPNPHONE
username ipphone2 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone2 attributes
vpn-group-policy VPNPHONE
username ipphone3 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone3 attributes
vpn-group-policy VPNPHONE
username oethera password WKJxJq7L6wmktFNt encrypted
username oethera attributes
vpn-group-policy cad_supplies_RAVPN
service-type remote-access
username markh password nqH+bk6vj0fR83ai0SAxkg== nt-encrypted
username markh attributes
vpn-group-policy cad_supplies_RAVPN
tunnel-group DefaultRAGroup general-attributes
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group cad_supplies_RAVPN type remote-access
tunnel-group cad_supplies_RAVPN general-attributes
address-pool VPN_IP_range
default-group-policy cad_supplies_RAVPN
tunnel-group cad_supplies_RAVPN ipsec-attributes
pre-shared-key *
tunnel-group VPNPHONE type remote-access
tunnel-group VPNPHONE general-attributes
address-pool VPN_Phone
default-group-policy VPNPHONE
tunnel-group VPNPHONE ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 1500
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8b25ecc61861a2baa6d2556a3679cc7c
: end

Hi,
You have your "group-policy" set so that you have excluding some networks from being tunneled.
In this access-list named Local_LAN_Access you specify "0.0.0.0"
Doesnt this mean you are excluding all networks from being tunneled? In other words no traffic goes to your tunnel.
This access-list should only contain your local LAN network from where you are connecting with the VPN Client. If you dont need to access anything on your local LAN while having the VPN on, you don't even need this setting on. You could just tunnel all traffic instead of excluding some networks.
- Jouni

Can i use same address pool for different remote access VPN tunnel groups and policy

Hi all,
i want to create a different remote access VPN profile in ASA. ihave one RA vpn already configured for some purpose.
can i use the same ip address pool used for the existing one for the new tunnel-group (to avoid add rotuing on internal devices for new pool) and its a temporary requirement)
thanks in advance
Shnail

Thanks Karsten..
but still i can have filtering right? iam planning to create a new group policy and tunnelgroup and use the existing pool for new RA and i have to do some filetring also. for the new RA i have to restrict access to a particualr server ,my existing RA have full access.
so iam planning to create new local usernames for the new RA and new group policy with vpn-filter value access-list to apply for that user as below, this will achive waht i need right??
access-list 15 extended permit tcp any host 192.168.205.134 eq 80
username test password password test
username test attributes
vpn-group-policy TEST
vpn-filter value 15
group-policy TEST internal
group-policy TEST attributes
dns-server value 192.168.200.16
vpn-filter value 15
vpn-tunnel-protocol IPSec
address-pools value existing-pool
tunnel-group RAVPN type ipsec-ra
tunnel-group RAVPN general-attributes
address-pool existing-pool
default-group-policy TEST
tunnel-group Payroll ipsec-attributes
pre-shared-key xxx

Remote Access VPN users unable to communicate with each other

Hi,
We have configured Remote Access VPN on Cisco IOS router. Users are able to access the inside resources but cant communicate to each other. Any suggestions on the issue?
Regards
Saif

Have you excluded the VPN traffic from being NATed when traffic is going between clients?
Please post a full sanitised configuration of the router so we can check it for configuration issues.
Please remember to select a correct answer and rate helpful posts

Remote access vpn going through another firewall segment

Hi,
Can i know that when use remote access vpn connect to asa firewall inside interface, after that the remote access vpn is it can connect to another firewall segment , the firewall segment is behind the inside interface?

Hello Sam,
As long as you include that traffic into the crypto acl and also on the NO_NAT configuration the answer would be yes. That is possible
Regards,
Julio

Easy VPN and remote access VPN

Hi all,
I have a pix running version 7.2, with two VPN connection:
1- normal remote access vpn with cisco vpn client.
2- easy vpn with another pix running version 6.3
both are working fine and i can access everything in HQ netweok.
questions is i need to enable communication between cisco vpn clinet to that remote side which has pix easy vpn . ??
please adivce what kind of configuration we need !!!!
regards,
hasan

Take a look at this link for easy VPN configuration.
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a008019e6d7.shtml

Remote Access VPN on Cisco ASA Problem

Similar Messages

Maybe you are looking for