Replaced Hdrive, now FCP STudio won't start up

HELP!!!!
I've experienced so much down time with all of this.
FCPro crashed when I tried to open, trashed preferences, still to no avail.
REInstalled FC Studio and updated to 6.06.
Still same problem, FCP crashes during Video Effects section of startup.
Usually during FX Factory, which I removed, but for some reason, the logo
still pops up.
Sherwood
<Edited by Host>

http://discussions.apple.com/thread.jspa?threadID=2349681&tstart=0
x

Similar Messages

I deleted my extensions manager and now my Mac won't start up. Please Help!!

I have an IMac, 24" model, running OS X. For the past several days, little warning windows have been popping up with this annoying beep, telling me that my computer was infected with various viruses. 4, to be exact. Also, while on the internet, random pop-up windows have appeared, so I thought I did have a virus. So, to correct the matter (or attempt to), I deleted my preferences folder from the system folder, as well as the extensions manager.
Now, the computer won't start up past the white logo screen with the turning gear thingy. I've tried resetting the PRAM, and starting in safe mode, and safe mode with the progress screen, and even something there while holding the option key (that one gave me an icon of my HD, but clicking on it took me back to an endless wait on the white screen). I've tried starting from the disk that came with the computer (I held the C key) but not only doesn't the computer start from the disk, it spits the disk out. I don't understand. The computer was fine until I deleted the ext. mgr and preferences, so it can't be that the computer went bad or something.
I don't know what else to do here. I do have an extended service warranty with Best Buy, but I wanted to see if there was some way to fix this before hauling this thing off to the store. Any suggestions? I'm desperate here, because anything and everything I've tried (based on all the try-this and try-thats I found on the internet), nothing has worked.
Please help.
Thanks in advance.

Well done! You've succeeded in turning your Mac into a useless brick.
Deleting the System/Library/extensions folder and the associated manager removed most of the functionality from your OS.
And all to get rid of what sounds like the MacDefender trojan or a variant.
ref; http://support.apple.com/kb/HT4650 and http://support.apple.com/kb/HT4651
You may have a slim chance of recovering if it will still boot in Target Disc Mode; in which case you can use another Mac to install the system remotely.
And I doubt your warranty with Best Buy is going to cover user "error."
Message was edited by: noondaywitch

SP1 for Exchange 2013 install fails with ECP virtual directory issues and now transport service won't start and mail is unavailable

SP1 for Exchange 2013 install failed on me with ECP virtual directory issues:
Error:
The following error was generated when "$error.Clear();
          $BEVdirIdentity = $RoleNetBIOSName + "\ecp (name)";
          $be = get-EcpVirtualDirectory -ShowMailboxVirtualDirectories -Identity $BEVdirIdentity -DomainController $RoleDomainController -ErrorAction SilentlyContinue;
          if ($be -eq $null)
          new-EcpVirtualDirectory -Role Mailbox -WebSiteName "name" -DomainController $RoleDomainController;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -FormsAuthentication:$false -WindowsAuthentication:$true;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -InternalUrl $null -ExternalUrl $null;
          . "$RoleInstallPath\Scripts\Update-AppPoolManagedFrameworkVersion.ps1" -AppPoolName:"MSExchangeECPAppPool" -Version:"v4.0";
        " was run: "The virtual directory 'ecp' already exists under 'server/name'.
Parameter name: VirtualDirectoryName".
Error:
The following error was generated when "$error.Clear();
          $BEVdirIdentity = $RoleNetBIOSName + "\ECP (name)";
          $be = get-EcpVirtualDirectory -ShowMailboxVirtualDirectories -Identity $BEVdirIdentity -DomainController $RoleDomainController -ErrorAction SilentlyContinue;
          if ($be -eq $null)
          new-EcpVirtualDirectory -Role Mailbox -WebSiteName "name" -DomainController $RoleDomainController;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -FormsAuthentication:$false -WindowsAuthentication:$true;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -InternalUrl $null -ExternalUrl $null;
          . "$RoleInstallPath\Scripts\Update-AppPoolManagedFrameworkVersion.ps1" -AppPoolName:"MSExchangeECPAppPool" -Version:"v4.0";
        " was run: "The operation couldn't be performed because object 'server\ECP (name)' couldn't be found on 'DC0xx.domain.com'.".
Error:
The following error was generated when "$error.Clear();
          $BEVdirIdentity = $RoleNetBIOSName + "\ECP (name)";
          $be = get-EcpVirtualDirectory -ShowMailboxVirtualDirectories -Identity $BEVdirIdentity -DomainController $RoleDomainController -ErrorAction SilentlyContinue;
          if ($be -eq $null)
          new-EcpVirtualDirectory -Role Mailbox -WebSiteName "name" -DomainController $RoleDomainController;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -FormsAuthentication:$false -WindowsAuthentication:$true;
          set-EcpVirtualdirectory -Identity $BEVdirIdentity -InternalUrl $null -ExternalUrl $null;
          . "$RoleInstallPath\Scripts\Update-AppPoolManagedFrameworkVersion.ps1" -AppPoolName:"MSExchangeECPAppPool" -Version:"v4.0";
        " was run: "The operation couldn't be performed because object 'server\ECP (name)' couldn't be found on 'DC0xx.domain.com'.".
!! And now transport service won't start and mail is unavailable !!
Any help would be appreciated.
I have removed the ecp site from default site and attempting to rerun SP1 now. I do not have high hopes. :(

Hi,
Thanks for your response.
From the error description, you need to manually remove the ECP with IIS manager in both the Default Web Site and the Exchange Back End firstly. And then continue the upgrade to check the result.
Hope this can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support

Took apart Macbook pro 13 to remove broken headphone tip in the jack. Had to remove battery to get to the headphone jack. Now the laptop won't start. The power button is just not responding. Battery indicator showed charge of 3 dots initially but now only

Took apart Macbook pro 13 to remove broken headphone tip in the jack. Had to remove battery to get to the headphone jack. Now the laptop won't start. The power button is just not responding. Battery indicator showed charge of 3 dots initially but now only the last dot is blinking. The power cable used to light up green initially but now the green light is gone. I have tried SMC reset, which didn't work. What are my options?

Macbook Pro2067 wrote:
<snip>
What are my options?
Take it to an authorized service center.

While updating the firmware Update, i disrubted the download and now my macbook won't start up! Any suggestions on how to fix it? i only see a black screen

While updating the firmware Update, i disrubted the download and now my macbook won't start up! Any suggestions on how to fix it? i only see a black screen and when i press the power button i hear the noise that it would make if it was going to start up. But i only see black.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Harddrive was replaced and now my computer won't recognize the IPOD

I recently had the hardrive replaced and now I can't seem to get it to charge, my itunes to recognize the ipod. I have tried several times restore and update. All I get is error messages "install wizard could not be completed" and "error in update manager". One thing...I have the IPOD with the color display and when I got it back and plugged it in (it worked long enough to download my music, but the display was in black and white. When I do get something on the screen it is a file with an exclaimation point and the www.apple.com/support/ipod website. HELP!!!!!

Hi,
A colour iPod without a workable system files, will display in play and white. I suggest that you should do a format first, before the Restore.
Please read the following for some suggestions
Hello,
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/ipod/download/
http://www.apple.com/itunes/download/
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iPod Updater and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iPod Updater and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“Partition Magic”.
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iPod updater.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
http://www.ipodresq.com/index.php
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning ! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.

NVRM error, now mt MBP won't start

Over the last 2 weeks, my MBP would crash (mostly during playing games). At first, I could just restart it and after a few restart it would be fine. But yesterday it crashed again after I managed to restart it (after another crash). But now it won't start up.
At start up, I would get the grey screen with Apple logo and then after 30 seconds or so, the grey screen gets distorted and generally the graphics are all messed up (and crash). I have tried booting up from Leopard CD, but it gets to a certain part and I get the Mac crash screen where it says the Mac has crashed and I need to restart.
Before it got to this stage, I have managed to restart it and after a restart, I got a noticed saying my Mac has crash and would I like to send report to Apple. So I did (3 times) and below is the error I got.
Fri Feb 6 22:56:59 2009
panic(cpu 0 caller 0x00405DEB): "NVRM: Read Error: GPU 0, PCI 0x00000100, BAR0 0x92000000 0x3a0e2000"@/SourceCache/xnu/xnu-1228.9.59/iokit/Kernel/IOLib.cpp:724
Backtrace (CPU 0), Frame : Return Address (4 potential args on stack)
0x39cb7548 : 0x12b4f3 (0x45b13c 0x39cb757c 0x1335e4 0x0)
0x39cb7598 : 0x405deb (0x49da40 0xda3280 0x39cb75dc 0x39cb75cc)
0x39cb75b8 : 0xb744f7 (0xda3280 0xda3280 0xd67c88 0x0)
0x39cb75f8 : 0xe2bd1a (0x4d73404 0x4d78804 0x100b80 0xbb356a)
0x39cb7638 : 0xe10feb (0x4d78804 0x100b80 0x0 0x0)
0x39cb7688 : 0xddb6ef (0x4d78804 0x4d8f804 0x39cb77b8 0x0)
0x39cb77f8 : 0xe44d16 (0x4d78804 0x4b7c004 0x0 0x1)
0x39cb7878 : 0xe1bd79 (0x4d78804 0x4bbc604 0x40 0x3e8)
0x39cb7998 : 0xcd6a00 (0x4d78804 0x4eeb804 0x39cb7a88 0x39cb7a88)
0x39cb7ab8 : 0xcd66c2 (0x4d78804 0x4ef4804 0x0 0x0)
0x39cb7b38 : 0xe14392 (0x4d78804 0x4ef4804 0x6 0x2)
0x39cb7bb8 : 0xe1517e (0x4d78804 0x4eeb804 0x1000 0x39cb7cdc)
0x39cb7d38 : 0xe46320 (0x4d78804 0x4eeb804 0x0 0x0)
0x39cb7e88 : 0xcca16f (0x4d78804 0x4bbc604 0x0 0x0)
0x39cb7ed8 : 0xb749b6 (0x4d78804 0x4bbc604 0x0 0x0)
0x39cb7f18 : 0x4224ff (0x0 0x4fb1c80 0x1 0x19eb5b)
Backtrace continues...
Kernel loadable modules in backtrace (with dependencies):
com.apple.nvidia.nv50hal(5.3.6)@0xdb8000->0x100cfff
dependency: com.apple.NVDAResman(5.3.6)@0xb5b000
com.apple.NVDAResman(5.3.6)@0xb5b000->0xdb7fff
dependency: com.apple.iokit.IONDRVSupport(1.7.1)@0xb4d000
dependency: com.apple.iokit.IOPCIFamily(2.5)@0x5d2000
dependency: com.apple.iokit.IOGraphicsFamily(1.7.1)@0xaee000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
9G55
Kernel version:
Darwin Kernel Version 9.6.0: Mon Nov 24 17:37:00 PST 2008; root:xnu-1228.9.59~1/RELEASE_I386
System model name: MacBookPro3,1 (Mac-F4238BC8)
This sounds very much like this error http://support.apple.com/kb/TS2377 but in this doc, nothing was said about not being able to start up the MBP.
The thing is I really need to boot up one last time to get some files off there, is there anyway I could boot up one last time? As I said before it won't boot up from HDD, not from CD, I tried booting up from external HDD but that system is 10.4 so it didn't show up.
Would appreciate any help so I can get these files off before I take it into repair!
Thanks

I just had a whole day of kernel panics and screen flicker (video flicker - not backlight) yesterday. I had stuck and incorrectly updated windows on the screen. Soon after that the machine crashed. A few reboots later the MacBook would freeze after a few minutes of use and then finally it would only boot into the dimmed screen of death or a stuck spinning wheel (even when booting form CD!!!). Inbetween, I managed to boot it from CD, but the machine crashed during disk check and finished the check (no errors) the third time!
I followed all instructions (5 secs power button while without battery and power) did NOT help.
I disconnected battery and power supply and let the MacBook sit for a few hours. That helped and magically the machine booted as if nothing happened.
I ran the loooong hardware test. Everything fine. I ran the disk check everything fine. I am clueless.
Today I had the same crash again, but at least everything was fine after a hard reboot. It even crashed the attached iPhone, which suddenly showed the Apple icon ?!? Hard to believe!
Remark: many of the crashes did not result in a kernel panic, but just froze the computer.
Kernel Panic Backtraces:
Backtrace continues...
Kernel loadable modules in backtrace (with dependencies):
com.apple.NVDAResman(5.4.4)@0xb6d000->0xdcbfff
dependency: com.apple.iokit.IONDRVSupport(1.7.3)@0xb5f000
dependency: com.apple.iokit.IOPCIFamily(2.6)@0x5cd000
dependency: com.apple.iokit.IOGraphicsFamily(1.7.3)@0xac6000
com.apple.iokit.IONDRVSupport(1.7.3)@0xb5f000->0xb6cfff
dependency: com.apple.iokit.IOPCIFamily(2.6)@0x5cd000
dependency: com.apple.iokit.IOGraphicsFamily(1.7.3)@0xac6000
com.apple.iokit.IOGraphicsFamily(1.7.3)@0xac6000->0xae2fff
dependency: com.apple.iokit.IOPCIFamily(2.6)@0x5cd000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
9J61
Kernel version:
Darwin Kernel Version 9.7.0: Tue Mar 31 22:52:17 PDT 2009; root:xnu-1228.12.14~1/RELEASE_I386
========== (Booted from CD) ===============
Backtrace continues...
Kernel loadable modules in backtrace (with dependencies):
com.apple.NVDAResman(5.1.6)@0x64308000->0x64534fff
dependency: com.apple.iokit.IONDRVSupport(1.5)@0x54eb1000
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x54efc000
dependency: com.apple.iokit.IOGraphicsFamily(1.5)@0x55146000
com.apple.iokit.IONDRVSupport(1.5)@0x54eb1000->0x54ebefff
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x54efc000
dependency: com.apple.iokit.IOGraphicsFamily(1.5)@0x55146000
com.apple.iokit.IOGraphicsFamily(1.5)@0x55146000->0x55161fff
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x54efc000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:35:55 PDT 2007; root:xnu-1228~1/RELEASE_I386
System model name: MacBookPro3,1 (Mac-F42388C8)
Message was edited by: katzlbt

G'day Matt Vass from AUS. I just installed mavericks and now garage band won't start due to BFD folder invalid,

Hi there, hoping for help pls. I just installed mavericks and now garageband old version won't start because the BFD folder is invalid.

Click Software Update from your Apple menu  drop down menu.
If there's nothing available from Software Update, you may need to purchaase the newest GB version 10.0.2 from the App Store.

IMovie lock up. I did hard reboot. Now Mac laptop won't start

iMovie lock up. I did hard reboot. Now Mac laptop won't start

Can you start up holding Command R to access your recovery partition? If so run Disk Utility to repair the boot volume, if not your hard drive may have failed. Without more information it's kinda hard to tell.

Moved system fonts now MacBook Pro won't start.

I have an early 2011 MacBook Pro running OS10.9.x and in an attempt to troubleshoot another issue I moved all the system fonts into a folder on the desktop. I didn't delete the font folder, just moved the fonts. When I went to restart the computer all it would do is flash between a white and gray screen and randomly display a progress wheel but won't start up.
Thanks for any help on how to resolve the issue.

Restart the computer with the Command and S keys held down and run the following, replacing the bold text:
mount -uw /
mv /Users/username/Desktop/foldername/* /System/Library/Fonts/*
exit
(117771)

Virus protector deleted plugins now my mac won't start up

I have downloaded a virus protector and deleted malware now my mac won't boot up only goes to grey screen with the gears turning help

I have the Maverick system and the virus protector had three upper case letters in the name as can't get on computer can't recall as just put on

Upgraded to Yosemite and now my laptop won't start HELP!!!

Last night I upgraded my Mac BookPro with yosemite and don't know if I did the right thing, my laptop won't startup, where the apple logo appears, after like 10-20sec, it appear a Decline logo and won't start, WHAT CAN I DO? Is there a way back? I had it for like 5 minutes and my computer was really slow and Microsoft Office, iMessages didn't open. I had to restart my computer and then I got stuck with the Decline LOGO!

Troubleshooting Apple Mail
Troubleshooting sending email messages

Replaced hard drive and upgraded RAM, now my Macbook won't start up?

At the suggestion of a "genius," I recently replaced the hard drive on my 2008 macbook with an SSD while also upgrading my RAM to 8 GB. When I attempt to power up, I get only a flashing gray folder with a question mark. I've tried several of the fixes from these forums (PRAM reboot, hold down "option" key, D, X, etc.) but nothing works. I rechecked the installation of the SSD and RAM and they look solid. Any suggestions?

My old hard drive crashed, so my intent was to restore the OS and everything else via my time machine back-up. (That's the direction I got from the genius rep.) Am I missing a key step somewhere?

FCP Studio won't launch

Hi,
I have a MacBook Pro and have used Final Cut Studio for the past 4 months. When I turned on my computer this morning, FCP will not launch when I double click it- i've tried launching it from my applications folder, turned my computer on and off- but nothing happens when I do this. I click on it and the icon just sits there and the program won't launch.
Yesterday I down loaded the newest upgrade- perhaps this has something to do with it.
Thank you!

Start with REPAIR PERMISSIONS... use DiskUtility from your Utilities folder.
If that doesn't work... trash your preferences with FCP Rescue.
CaptM

Replaced HDD, now MacBook Pro won't power on.

Just bought a new HDD, Seagate Momentus 750Gb (link below). Installed it in my MacBook Pro, replacing the old 160Gb drive (also a Seagate Momentus, older version though) and when I tried to boot my laptop back up it won't even power on. I don't hear anything starting up, and the status light on the front doesn't turn on either. Putting the old drive back in and booting up it works perfectly fine, just like it did before swapping drives. The drive is supposed to be compatible with my laptop (MacBook Pro 3,1 Late 2007 15"). The drive is not partitioned or formatted, but this should not affect the laptop from powering up. I have no other computer to try the drive in to see if it is DOA but even if it were it again should not affect the laptop from powering up. Any advice on what could be causing the problem or something that I may have overlooked would be much appreciated.
Thanks, Chris
http://www.seagate.com/ww/v/index.jsp?name=st9750420as-momentus-7200-sata-3gbs-7 50-gb-hd&vgnextoid=25dcb937455b7210VgnVCM1000001a48090aRCRD&locale=en-AU&pf=1

Hi c,
Your options, as I see them:
1. Contact Seagate tech/warranty support and see what they have to say.
2. Get an external enclosure to try the HD in.
3. Find another MBP to try the HD in.

Replaced Hdrive, now FCP STudio won't start up

Similar Messages

Maybe you are looking for