Satellite M30-704 boot slow and 0203 failure IDE#2 message after drive replace

Hi,
two problems:
firstly after replacing the cd/dvd drive my computer will not now boot automatically and shows an '0203 failure IDE#2' message. I can then boot it but this all takes time?
second problem: before I can access any programme, a message reading: 'apdproxy.exe - Application Error - the application failed to initialize properly (0xc0000006)' appears twice before I can continue and the computer is then very slow.
Can anyone offer any solutions? (ps - these two problems are not linked as they occurred months apart).
Thanks, Gardiner

1.) I would say the BIOS cannot handle the new drive properly because of the wrong master/slave/c-sel settings but its strange that the drive runs.
I think you should check in the device manager the primary and secondary IDE channels.
The transfer mode should be set to DMA if available and device type Auto detection
2.) It seems the 'apdproxy.exe is a part of the Adobe Photoshop or similar application.
This software could cause an error. So simply try to reinstall this program

Similar Messages

0203 failure IDE#2 message after drive replacement

My DVD is UJ-820B and i replaced it with the exact same one.
The dif is that the old is FW: 1.00 while the new one is FW: 1.05
1. Is the only solution to fix pin? If yes can you pls confirm with which pins.
2. The error IDE#2 means that: DVD bay is on Primary Slave while DVD is Secondary Master or vice versa?
Can you extra please let me know.
If you wish contact me via email at [email protected]

I guess the CD/DVD drive supports another master/slave/c-sel setting.
The IDE#2 error appears because the BIOS cannot recognize the drive correctly.
The problem is that its not possible to change such settings like on a external drives by changing the jumper a special internal firmware controls such settings.
You have suggested that the drive is the same but the firmware is different.
Well, in my opinion this is a reason for the issue

My iPod(4g) is slow and when i open a app, after few minutes it automatically closes and also takes about 4 minutes to enter settings app.

My iPod(4g) is slow and when i open a app, after few minutes it automatically closes

Sounds like a software issue. Back-up the iPod to a computer and then restore the software via iTunes and set it up as a new device. If it is working fine then restore your backup to the device. If it is still playing up before you put your information back on then it is most likely a faulty device, and would need a service.

Node failed to join the cluster because it ould not send and receive failure detection network messages

One of my customers has a Windows Server 2008 R2 cluster for an Exchange 2010 Mailbox Database Availability Group. Lately, they've been having problems with one of their nodes (the one node that is on a different subnet in a different datacenter) where
their Exchange databases aren't replicating. While looking into this issue it seems that the problem is the Network Manager isn't started because the cluster service is failing. Since the issue seems to be with the cluster service, and not Exchange,
I'm asking here.
When the cluster service starts, it appears to start working, but within a few minutes the following is logged in the system event log.
FailoverClustering
1572
Critical
Cluster Virtual Adapter
Node 'nodename' failed to join the cluster because it could not send and receive failure detection network messages with other cluster nodes. ...
It seems that the problem is with the 169.254 address on the cluster virtual adapter. An entry in the cluster.log file says: Aborting connection because NetFT route to node nodename on virtual IP 169.254.1.44:~3343~ has failed to come up.
In my experience, you never have to mess with the cluster virtual adapter. I'm not sure what happened here, but I doubt it has been modified. I need the cluster to communicate with its other nodes on our routed 10. network. I've never experienced
this before and found little in my searches on the subject. Any idea how I can fix this?
Thanks,
Joe
Joseph M. Durnal MCM: Exchange 2010 MCITP: Enterprise Messaging Administrator, Exchange 2010 MCITP: Enterprise Messaging Administrator, MCITP: Enterprise Administrator

Hi,
I suspected an issue with communication on UDP port 3343. Please confirm the set rules for port 3343 on all the nodes in firewall and enabled all connections for all the profiles
in firewall on all the nodes are opened, or confirm the connectivity of all the node.
Use ipconfig /flushdns to update all the node DNS register, then confirm the DNS in your DNS server entry is correct.
The similar issue article:
Exchange 2010 DAG - NetworkManager has not yet been initialized
https://blogs.technet.com/b/dblanch/archive/2012/03/05/exchange-2010-dag-networkmanager-has-not-yet-been-initialized.aspx?Redirected=true
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

I have checked all of my permissions and contiue to get this message after 68% mark when trying to install Adobe flash player. User does not have sufficient privileges to install adobe flash player. A required file (C:\windows\syswow64\macromed\flash\flas

I have checked all of my permissions and contiue to get this message after 68% mark when trying to install Adobe flash player. User does not have sufficient privileges to install adobe flash player. A required file (C:\windows\syswow64\macromed\flash\flashplayer.xpt:5) could not be written due to insufficient permission.

Perform a clean install as described in https://forums.adobe.com/thread/928315

My Firefox won't quit and gives a "not responding" message after I use Google Mail. I have tried starting in "safe" mode and the problem still occurs.

I have an issue where Firefox wont' quit and gives a "not responding" message after I have been using Google Mail. It works fine when I am not using that program. I have tried Safe Mode and the problem still happens when I go to Google Mail, so it is not connected with add-ons, extensions, etc.

Many site issues can be caused by corrupt cookies or cache. 
Clear the Cache 
'''''Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"'''''
 and 
Remove Cookies '''''Firefox/Tools > Options > Privacy.''''' 
Under '''History''', select Firefox will '''Use Custom Settings'''. 
There is a button on the right side called '''Show Cookies'''. 
If there is still a problem,
'''''[https://support.mozilla.org/en-US/kb/troubleshoot-firefox-issues-using-safe-mode Start Firefox in Safe Mode]'''''
 While you are in safe mode; '''''Firefox Options > Advanced > General'''''. 
Look for and turn off '''Use Hardware Acceleration'''. 
Poke around safe web sites and see if there is still a problem. Then restart.

Satellite A30 wont boot up and is stuck on "exiting PXE ROM"

A30 wont boot up and is stuck on a loop
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM.
I dont have recovery discs and bios does not allow to turn off any relevant settings.

The error message PXE-E61: Media test failure, check cable appears because the notebook tries to boot from the LAN.
There could be a different reason why the notebook doesnt boot from the HDD or from another source.
Firstly the wrong booting order could prevent the notebook from HDD booting.
Secondly the missing HDD or an HDD malfunction could cause this issue.
You should definitely try to access the BIOS pressing the F2 button immediately after notebook starting. There you should check if the HDD was recognized.
If not, then I recommend replacing the HDD and to reinstall the OS.
Best regards

"No Bootable Device -- insert a boot disk and press any key" Error Message.

Last month I just got a HP netbook (HP Mini 110-3100) and when I got it from the box, the error message; "No bootable device -- insert a boot disk and press any key" appeared. But then I managed to boot up the netbook normally. After that, I can use the netbook normally but the error message keeps appeared and becomes more frequent and now I even cannot turn on the netbook.
Is it a hard disk failure?
p/s: yesterday accidentally I can turn on the netbook without any problems. Did a lot of Hard Disk Maintenance by some softwares downloaded from the internet. But now already cannot turn on.
p/s/s: i have no cd/dvd drive, and also no 8GB usb drive.
p/s/s/s: what should i bring if i want to send the netbook to the HP centre? just bring the netbook?

I would suggest try and reseat the hard drive and check...If you still have the issue, than take it to the service center...And you will need to take only netbook to Service center...
Although I am an HP employee, I am speaking for myself and not for HP.
Make it easier for other people to find solutions, by marking my answer with 'Accept as Solution', if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

Computer freezes 9/10 times on start up, running slow, and a lot of error messages

Hi guys,
Im new tot his site, but am trying to find someone that can help resolvemy computer issues.
it started off running really slow and freezing during programs, and then i started getting error messages every time ibooted the computer, and now 9 out of 10 times i try to bootup orrestartthe computer will freeze and just shows a black screen. only
computer is a HP pavilion tx2000 (notebook)
i have used a forum website called spyware ware warrior to try and resolve the issues, which they help check for malware but were unable to resolve what is wrong...
i would apreciate any help you can give.
cheers

Hi Steve,
I think the most likely answer to solve this problem would be to reinstall the operating system using your Recovery Discs ( not the Recovery Partition on the Hard Drive ) as there are probably corrupt Windows files caused by the malware infection that the system file check cannot detect or repair.
I realise reinstalling the OS can be a pain, so you may want to try the following first.
Start the notebook and let Windows fully load. Hold down the Windows key and press R. In to the Run box type msconfig and hit enter. In the following window, click the Start up tab, remove the tick next to each start up item and then click Apply to make the change. Reboot the notebook and see if it now starts and runs normally. If it does, re-enable one start up item at a time, click Apply and reboot to check if it still runs ok. Keep doing this until you encounter the problem again and you will know the last program you set to start is causing the issue.
If the above process doesn't help, the best option left would be to reinstall the OS - Make sure to backup all your personal files etc first. If you don't have your Recovery Discs, you can order a replacement set of using the link below - these are around $30 in the US.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00810334&cc=us&lc=en&dlc=en
If you have any problem with this link, order them directly from HP.
If you live in the US, contact HP Here.
If you are in another part of the world, start Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

I just updated to new software, this was my first mistake, at first contacts were not there and my pics, and it deleted all my messages, after alot of research i got all this back, but now cant text, getting error "sms box is full"

i just updated to the new software, now im getting error when i send a txt "cannot receive in box is full" ive deleted alot and cant get this fixed, also when i first did the update i lost all contacts, pics and it deleted all txt conversations after several restores i did get all that back but cannot receive txt, any suggestions?

Close all open apps by double-tapping the home button, then swiping up and off the screen with the app window (not the smaller icon).
Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. (No data loss)

U410 booting slow and windows app slow

My Lenovo U410 is taking a lot longer to boot up nowadays (5-7mins) compared to when I purchased it less than a year ago (about 20 seconds).
I think the mSATA (24GB) is not working properly, but I am not 100% sure.
From other threads and other sources on the internet, I have tried the following things.
Downloaded HDTune and ran Error Check
- Got 1340 disck errors by the 83 MB mark in 3hrs of scanning. Decided to abort since scanning the full 24GB would take too long.
BIOS
- Rapid Start was Enabled, but the iRST PARTITION STATUS was INVALID, but SATA controller mode was AHCI (when I tried to change to RAID, the system would report an error on startup and be stuck in a restart loop)
Also read that Lenovo uses expresscache (does it not use intel rapid start technology?)
- type command eccmd.exe -info
- returned HFS volume not mounted **ERROR** eccmd exited with error 0x45d (1117)
However, my computer seems to be able to detect the 24GB mSATA. It also passes a chkdsk.
Another problem I am having is with Windows applications. For example, when i try to run msconfig it takes 5mins to load a simple and small program.
In the recent past, Windows wouldn't restart (just hangs there), windows installer wouldn't install some programs (just hangs), but it seem to fix itself recently.
I am hoping for steps to restore my original boot time. (do i look to install expresscache or intel rapid start?)
Is there anything anybody could suggest? Is there a definitive way to check if the mSATA is defective?

hi leon09,
In addition to what have already been suggested, I'm positive that the cause of the slow boot-up is the SSD drive. The 1340 disk errors that you received after running an error scan on the SSD proves that the SSD needs to be replaced.
If you're still able to boot into Windows, try to go to the Control Panel (large icon view) > Programs and Features and uninstall Diskkeeper Expressache. After uninstallation, reboot the PC and observe.
For the SSD, you may need to contact lenovo for service on how to go about getting the SSD replaced.
If you purchase the laptop in Canada, here's the number:
Country or Region
Product
Language
Telephone number
Hours of operation
Africa
THINK-branded products
English, Afrikaans
South Africa
0800 110756
9AM - 6PM
Saturday - Wednesday
Central Africa
Contact the nearest Business Partner
Algeria
THINK-branded products
French, English
+33-6-7348 1739
Argentina
THINK-branded products
Spanish
0800-666-0011
9AM - 7PM
Monday - Friday
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
Spanish, English
0800-266-0570
8AM - 10PM
Monday - Sunday
Aruba
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
English
1-877-4-LENOVO
1-877-453-6686
24 hours a day
7 days a week
Australia
THINK-branded products
English
1-800-041-267
6 AM – 8 PM AEST Monday to Friday
ThinkServer
English
1-800-041-267
6 AM – 8 PM AEST Monday to Friday
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
English
1-800-041-021
24 hours a day
7 days a week
Austria
THINK-branded products
German
0810-100-654
9 AM - 6 PM
Monday - Friday
ThinkServer
German
01-211-454-610
8AM - 4PM
Monday - Friday
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
German
0810-151-500
(zum Ortstarif)
9AM - 6PM
Monday - Friday
Bahamas
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
English
1-877-4-LENOVO
1-877-453-6686
9AM - 6PM
Bahrain
THINK-branded products
Kanoo IT :
00-973-1771-1722
Bahrain Business Machine LLC :
00-973-1758-4302
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
English, Arabic
00-9731-749-0330
9AM - 6PM
(Sunday - Thursday)
Bangladesh
All Lenovo Products
AWSP Flora Limited:
19-011-014-918
88-018-1708-2968
(Mobile)
Email: [email protected]
AWSP Global Brand Pvt Ltd:
70-200-6853
88-0171-000-0000 (Mobile)
Email: [email protected]
Barbados
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
English
1-877-4-LENOVO
1-877-453-6686
24 hours a day
7 days a week
Belgium
THINK-branded products
Dutch, French
02-339-36-11
(Warranty service and support)
9 AM - 5 PM
Monday - Friday
ThinkServer
Dutch, French
02-339-36-11
24 hours/day
7 days/week
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
Dutch, French
02-700-73-77 (lokaal tarief)
9AM - 6PM
Monday - Friday
Bermuda
THINK-branded products
English
1-800-426-7378
24 hours/day
7 days/week
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
English
1-877-4-LENOVO
1-877-453-6686
24 hours a day
7 days a week
Bolivia
THINK-branded products
Spanish
0800-10-0189
8AM - 6PM
Monday - Friday
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
Spanish, English
0800-10-0982
8AM - 10PM
Monday - Sunday
Bosnia and Herzegovina
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
Bosnian
387-3356-3170
9AM - 5PM
Monday - Friday
Brazil
THINK-branded products
Brazilian Portuguese
Calls made from within the Sao Paulo region
11-3889-8986
8 AM - 6 PM
Monday - Friday
Calls made from outside the Sao Paulo region
0800-701-4815
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
Brazilian Portuguese
Technical Support:
Sao Paulo Brazil
11-3140-0500 - Toll
0800-885-0500 -Toll Free
9AM - 8PM
Monday - Friday
General Information:
Sao Paulo Brazil
11-4003-5366 - Toll
0800-888-5366 - Toll Free
9AM - 5PM
Saturday (Except holidays)
Brunei Darussalam
THINK-branded products
English, Bahasa Melayu
Dial 800-1111,
then dial 866-273-5446
9AM - 6PM
Monday - Friday
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
English, Bahasa Melayu
Dial 800-1111,
then dial 877-404-9661
9AM - 6PM
Monday - Friday
9AM - 3PM
Saturday
Bulgaria
ThinkServer
359-2-9734618
359-2-9693650
8:30 AM - 5PM
7 days/week
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
Bulgarian
00800-11-944-26
9AM - 6PM
Monday - Friday
Canada
IDEA-branded and
B, C, E, G, H, K, N, Q, V, Y Series Products
English
1-877-4-Lenovo
(1-877-453-6686)
24 hours/day
7 days/week
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Macbook Pro Running Slow and have NO Idea Why!

For the last few days, my 10 month old Macbook Pro has been running really slowly. Sometimes, it is perfectly normal. But other times, it just is really slow. Typing will show up a few seconds later, it will take a few seconds to switch tabs in safari/chrome, and it takes a while for an application to open. Anyone have any idea what could be going on?

First, back up all data immediately, as your boot drive might be failing.
There are a few other possible causes of generalized slow performance that you can rule out easily.
Reset the System Management Controller.
If you have many image or video files on the Desktop with preview icons, move them to another folder.
If applicable, uncheck all boxes in the iCloud preference pane.
Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
Check your keychains in Keychain Access for excessively duplicated items.
Boot into Recovery mode, launch Disk Utility, and run Repair Disk.
Otherwise, take the steps below when you notice the problem.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
Select the CPU tab of the Activity Monitor window.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
Step 2
If you have more than one user account, you must be logged in as an administrator to carry out this step.
Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long.

I messed up while installing Boot Camp and now I can't restore my drive to a single partition.

Hey all, I have a late 2013 iMac on 10.9.4. Just got it a few days ago and tried to install my copy of 8.1 on it.
After taking a while to create a bootable USB disk, I partitioned ~470GBs through Boot Camp Assistant to use as a Windows partition. Long story short, during my install, I ran into some problems while choosing the drive to install Windows onto. Now I remember when installing Windows 7 on my MBP, deleting the partition and reformatting did the trick, so I tried that. Windows gave me a prompt saying it will create new partitions for system files. I didn't think much of it, so I said sure. After all that, still ran into some problems.
Was about to give up to I rebooted into OSX to restore my drive, but was met with this error:
I checked my disk utility and I had 2 extra partitions--disk 1s4 and 1s5 or something similar. Managed to get rid of one, but the other one was impossible to get rid of, despite my efforts. Now I have my main partition, a disk1s4 partition I can't get rid off, and and 478.09GBs of free space that I can't get back at the moment.
So. I messed up. What are my options now?
Here's what it says in diskutil list:
Thanks guys, any help is appreciated.

I tried to restore the previous session as I've done so several times before, but I was not given the option. It simply did not show up on my browser history. I also tried to restore a previous version of the sessionstore file, but it did not do anything except erase my browser history from the restoration point. Also, after i restored the sessionstore file, the ability to see my "ghost" tabs that were open is now gone, so I assume it's lost forever. I deleted the sessionstore file before restoring it, and put it back into the folder, but that did not restore my history. What am I doing wrong?

Slow and crash when activity in Windows network drive

A weeks ago I clean install my Mac Pro using Snow Leopard and upgrade it to 10.6.2, I fell that connection to network drive is very slow, got crash and stuck when delete file in the network drive. I tried to relaunch the Finder but it become dead finder I can't execute the finder anymore then I have to restart my machine. And also I got Kernel panic several times that I never have any in 10.5.7. And also so many problem I got since I install Snow Leopard on my machine.
I really disappointed and just wasting my money and my time dealing with all these problems, and downgrade to 10.5 I think the cheapest way to deal with this.

HI,
*"And also I got Kernel panic several times that I never have any in 10.5.7"*
*"And also so many problem I got since I install Snow Leopard on my machine."*
Anytime you upgrade from one Mac OS X to the next it's reallly important do check to see if all your peripherals, third party software are compatible BEFORE you upgrade your Mac. You can save yourself the problems you are experiencing.
Read the post here by "a brody"..
http://discussions.apple.com/thread.jspa?messageID=10180165#10180165
Go here for help to Resolve Kernel Panics
Carolyn

HT6114 i have a mac mini that wont boot up and the screen says unable to find driver for this platform: \ powermac10.2 it also says mac os version not yeet set...how can i fix it

the mac mini wont boot up it says you need to restart yuor computer and that its unable to find river for platform can i download software free from the internet to fix this

What OS were you using on the mini before this problem started? If 10.7.8.9, boot to the Recovery Volume (command - R on a restart or hold down the option key during a restart and select Recovery Volume). Run Disk Utility Verify/Repair and Repair Permissions. Then reinstall the OS.
OS X Recovery
OS X Recovery (2)

Satellite M30-704 boot slow and 0203 failure IDE#2 message after drive replace

Similar Messages

Maybe you are looking for