Saving a file in Vi creates same file but with ~ added [SOLVED]

Hi,
I'm not sure if I pressed a key combination, but when I save a file in Vi I get another file that has the same name as the original file but with the ~ character added to the end of the filename.  For example, if I edit foo.txt and save it, then the original will be saved, but I'll also get a new file named foo.txt~.  Does anyone know how to fix this?
Thanks!
-nterpol
Last edited by nterpol (2008-11-09 12:30:59)

I think that the default backup settings (in /etc/virc if you use the basic vi package) changed with the recent upgrade to Vim 7.2.25.
For information on file backup setting combinations, see :help backup-table in Vim.
Edit:
fwojciec wrote:http://thehumblecoder.wordpress.com/200 … kup-files/
That article advocates disabling the use of swap files (:set noswapfile); however, I wouldn't recommend it. Whereas backup files are designated with a trailing tilde (~), swap files have names ending with .swp. The latter should be removed automatically when Vim exits (unless it is exited abnormally, such as when the user closes a terminal emulator without first quitting an instance of Vim that is running inside it).
Last edited by ssjlegendx (2008-11-10 04:13:24)

Similar Messages

  • To create 3 diff files with same content but with diff names in same target

    Hi SapAll.
    i have got a a requirement where pi need to create 3 different files with same content but with different names under same target from a single Idoc.
    its an IDOC to 3 File Inteface.
    can any body help me in providing the differnt solutions for this without use of any script executions.
    will be waiitng for response.
    regards.
    Varma

    > i want to use only one communication channel to produce 3 different file names with same content ,so here i should use only one message mapping in 3 operation mappings .
    This is not possible to produce 3 different file names with single CC. You have to use 3 different CCs. unless you have going to use some other trick e.g some script to rename the file etc..
    As I suggested in my previous reply use Multi-Mapping Or create 3 different Interface Mappings (by using the same MM).
    Note: You have to create 3 different Inbound Message Interfaces (you can use the same Inbound Message Type) otherwise while creating the 3 Interface Determination it won't allow because of same Outbound & Inbound Message Interface. It will simply say Interface alreday exists..
    So, just use the Multi-Mapping which is best solution in my opinion, because the benefit of using multi-mapping are:
    1. You have to create only single Message Mapping
    2. Single Interface Mapping
    3. Single Receiver Determination
    4. Single Interface Determination
    5. 3 Receiver CCs (3 you have to use in any case)
    6. Performance wise it is good (read the blog's last 2 para)
    7. And last but not the least easy to maintain the scenario.

  • To create multiple files with same content but with different names

    Hi SapAll.
    here i have got a tricky situation on Idoc to File Scenario.
    in my interface of an Idoc to file ,there  is requirement to create multiple files with different file names but with same content based on one Idoc Segment.
    which means there will be one Zsegment with two fields in the idoc,where one field with (content refers to the name which file name should start with .so lets say if this segment is repeated for 3 times then PI should create 3 files in the same directory with same content but with different file names (from the filed).
    so here for now iam using one reciever file communication channel.
    can any body give me the quick answer.
    regards.
    Varma

    What do you mean by different names?
    when i make proper setting in the Receiver Channel....on how to create the filename (what to append) like add Timestamp, counter, date, messageid.....even in this case you will ahve file with different names and that too from same File channel.
    You can perform multi-mapping in XI/ PI and then your File channel will place the files in the target folder with relevant names. You cannot use Dynamic Configuration with Multi-Mapping!
    If you intend to use different File channels, then do the configuration as required (normal)...even over here you can follow multi-mapping.
    Do not use a BPM!
    Regards,
    Abhishek.

  • I am trying to create mp3 version of itune songs.  I have gone through the preference sequence to be mp3 encoder but this is not having any effect.  I have also tired from file tab to create a version but this is not available to action

    I am trying to create mp3 version of itune songs.  I have gone through the preference sequence to be mp3 encoder but this is not having any effect.  I have also tired from file tab to create a version but this is not available to action showing as lite grey.
    Any help would be appreciated

    I am trying to create mp3 version of itune songs.  I have gone through the preference sequence to be mp3 encoder but this is not having any effect.  I have also tired from file tab to create a version but this is not available to action showing as lite grey.
    Any help would be appreciated

  • I worked with files in LR that were originally on my C drive, then were moved to an external HD for storage. I now want to do some more work on those files (which have the same file name as on the C drive). I plugged the drive into my computer and it show

    I worked with files in LR that were originally on my C drive, then were moved to an external HD for storage. I now want to do some more work on those files (which have the same file name as on the C drive). I plugged the drive into my computer and it shows in LR under folders as the F drive and the little green light is on, but LR is showing only the first 6 files and not the remaining 200 or so. How do I expand the F folder to expose all files?

    I worked with files in LR that were originally on my C drive, then were moved to an external HD for storage. I now want to do some more work on those files (which have the same file name as on the C drive). I plugged the drive into my computer and it shows in LR under folders as the F drive and the little green light is on, but LR is showing only the first 6 files and not the remaining 200 or so. How do I expand the F folder to expose all files?

  • Ability to process several raw files with the same content but with different exposure into the single picture

    Can you add to the Lightroom an ability to process several raw files with the same content but with different exposure into the single picture?
    Base raw files can be given with exposure bracketing during shooting, for example.
    The goal - to get maximum details in darks and lights (if we use the "ligths recovery" or "fill lights" we lose the quality because raw file just have no all required information).
    The similar (but not the same, only the idea) thing - is High Dynamic Range Photography in Adobe Photoshop
    Thank you

    The plugin LR/Enfuse does this already. And of course Photomatix have a plugin available for Lightroom. This essentially amounts to pixel editing, which is beyond the range of Lightroom's metadata editing.

  • Can we create same party site with same customer in different OU

    I am able to create same party sites with same customer in different Operating Unit through front end but I am not able to do so using TCA Api HZ_CUST_ACCOUNT_SITE_V2PUB.create_cust_acct_site .I am getting the below error 'Value for cust_account_id - party_site_id must be unique'.Ineed to migrate customer details from one OU to another OU and the party site number need to be same .Can anyone suggest a way in which I can do the above ?
    Reeja

    We can create multiple customer acct site across different OU pointing to same party_site_id with API's also. I am sure that you have initialise the org context in your code somewhere and thus its giving you this error. Reinitialise the org to target org before calling this API.
    Thanks
    Amit Singh

  • I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .

    HI All,
    I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
    Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
    The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
    here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
    show run-config
    Press Enter to continue...
    System Inventory
    NAME: "Chassis"   , DESCR: "Cisco 5500 Series Wireless LAN Controller"
    PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    System Information
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.235.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
    Build Type....................................... DATA + WPS
    System Name...................................... WLAN Controller 5508
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 10.125.18.15
    Last Reset....................................... Software reset
    System Up Time................................... 41 days 5 hrs 14 mins 42 secs
    System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... US - United States
    --More or (q)uit current module or <ctrl-z> to abort
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    External Temperature............................. +20 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 10
    Number of Active Clients......................... 61
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    AP Bundle Information
    Primary AP Image  Size
    ap3g1             5804
    ap801             5192
    ap802             5232
    c1100             3096
    c1130             4972
    c1140             4992
    c1200             3364
    c1240             4812
    c1250             5512
    c1310             3136
    c1520             6412
    c3201             4324
    c602i             3716
    Secondary AP Image      Size
    ap801             4964
    c1100             3036
    --More or (q)uit current module or <ctrl-z> to abort
    c1130             4884
    c1140             4492
    c1200             3316
    c1240             4712
    c1250             5064
    c1310             3084
    c1520             5244
    c3201             4264
    Press Enter to continue or <ctrl-z> to abort
    Switch Configuration
    802.3x Flow Control Mode......................... Disable
    FIPS prerequisite features....................... Disabled
    secret obfuscation............................... Enabled
    Strong Password Check Features:
           case-check ...........Enabled
           consecutive-check ....Enabled
           default-check .......Enabled
           username-check ......Enabled
    Press Enter to continue or <ctrl-z> to abort
    Network Information
    RF-Network Name............................. OGR
    Web Mode.................................... Disable
    Secure Web Mode............................. Enable
    Secure Web Mode Cipher-Option High.......... Disable
    Secure Web Mode Cipher-Option SSLv2......... Enable
    OCSP........................................ Disabled
    OCSP responder URL..........................
    Secure Shell (ssh).......................... Enable
    Telnet...................................... Disable
    Ethernet Multicast Forwarding............... Disable
    Ethernet Broadcast Forwarding............... Disable
    AP Multicast/Broadcast Mode................. Unicast
    IGMP snooping............................... Disabled
    IGMP timeout................................ 60 seconds
    IGMP Query Interval......................... 20 seconds
    User Idle Timeout........................... 300 seconds
    ARP Idle Timeout............................ 300 seconds
    Cisco AP Default Master..................... Enabled
    AP Join Priority............................ Disable
    Mgmt Via Wireless Interface................. Disable
    Mgmt Via Dynamic Interface.................. Disable
    --More or (q)uit current module or <ctrl-z> to abort
    Bridge MAC filter Config.................... Enable
    Bridge Security Mode........................ EAP
    Mesh Full Sector DFS........................ Enable
    AP Fallback ................................ Enable
    Web Auth Redirect Ports .................... 80
    Web Auth Proxy Redirect ................... Disable
    Fast SSID Change ........................... Enabled
    AP Discovery - NAT IP Only ................. Enabled
    IP/MAC Addr Binding Check .................. Enabled
    Press Enter to continue or <ctrl-z> to abort
    Port Summary
               STP   Admin   Physical   Physical   Link   Link
    Pr Type   Stat   Mode     Mode     Status   Status Trap    POE   SFPType  
    1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
    2 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    3 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    4 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    5 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    6 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    7 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    8 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    Press Enter to continue or <ctrl-z> to abort
    AP Summary
    Number of APs.................................... 8
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1       US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1       US       1
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1       US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1       US       1
    Anham_AP03           2     AIR-LAP1142N-A-K9     70:81:05:88:15:b5 default location 1       US       1
    ANHAM_AP01          2     AIR-LAP1142N-A-K9     70:81:05:b0:e4:62 Small Conference 1       US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1       US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9     70:81:05:96:7a:49         Copy Room 1       US       1
    AP Tcp-Mss-Adjust Info
    AP Name             TCP State MSS Size
    KNOWLOGY_DC01       disabled   -
    KNOWLOGY_DC02       disabled   -
    --More or (q)uit current module or <ctrl-z> to abort
    KN1252_AP01         disabled   -
    KN1252_AP02         disabled   -
    Anham_AP03           disabled   -
    ANHAM_AP01           disabled   -
    ANHAM_AP04           disabled   -
    ANHAM_AP02           disabled   -
    Press Enter to continue or <ctrl-z> to abort
    AP Location
    Total Number of AP Groups........................ 3  
    Site Name........................................ ANHAM8075
    Site Description................................. ANHAM 8075 Location
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Anham_AP03           2     AIR-LAP1142N-A-K9   70:81:05:88:15:b5 default location 1     US       1
    ANHAM_AP01           2     AIR-LAP1142N-A-K9   70:81:05:b0:e4:62 Small Conference 1     US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1     US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9   70:81:05:96:7a:49         Copy Room 1     US       1
    Site Name........................................ Knowlogy_DC
    --More or (q)uit current module or <ctrl-z> to abort
    Site Description................................. DC Center Access points
    WLAN ID         Interface         Network Admission Control         Radio Policy
    2               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1     US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1     US       1
    Site Name........................................ OGR
    Site Description................................. 1934 OGR Office
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                        None
    4               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    --More or (q)uit current module or <ctrl-z> to abort
    7               knowlogy_ogr        Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1    US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1     US       1
    Site Name........................................ default-group
    Site Description................................. <none>
    WLAN ID        Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    5               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                          None
    --More or (q)uit current module or <ctrl-z> to abort
    9               knowlogy_ogr         Disabled                         None
    10             management           Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Press Enter to continue or <ctrl-z> to abort
    AP Config
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch IP Address.................. 10.125.18.15
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
        Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
        Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
    --More or (q)uit current module or <ctrl-z> to abort
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 11
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
    --More or (q)uit current module or <ctrl-z> to abort
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
          CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
          36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
         Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 44
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
          Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W  Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    --More or (q)uit current module or <ctrl-z> to abort
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
        Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
    --More or (q)uit current module or <ctrl-z> to abort
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 1
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
         Coverage exception level................... 25 %
    --More or (q)uit current module or <ctrl-z> to abort
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
           36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
        Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 36
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
          Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 5
    Cisco AP Name.................................... KN1252_AP01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:ef:06:50
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.125.18.101
    IP NetMask....................................... 255.255.255.0
    Gateway IP Addr.................................. 10.125.18.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Enabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ Knowlogy Conference Rooms Side
    Cisco AP Group Name.............................. OGR
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.4.10.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. PoE/Medium Power (15.4 W)
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1252AG-A-K9
    AP Image......................................... C1250-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX122990L5
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 118
          WLAN 1 :........................................ 111
          WLAN 2 :........................................ 111
          WLAN 4 :........................................ 112
          WLAN 6 :........................................ 112
          WLAN 7 :........................................ 111
          WLAN 9 :........................................ 112
          WLAN 8 :........................................ 112
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 26 days, 00 h 24 m 39 s
    --More or (q)uit current module or <ctrl-z> to abort
    AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
    Join Date and Time............................... Wed Oct 9 10:59:07 2013
    Join Taken Time.................................. 0 days, 00 h 00 m 50 s
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211n-2.4
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 7
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:df:a5:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           11000 Kilo Bits.......................... MANDATORY
         MCS Set
           MCS 0.................................... SUPPORTED
           MCS 1.................................... SUPPORTED
           MCS 2.................................... SUPPORTED
           MCS 3.................................... SUPPORTED
           MCS 4.................................... SUPPORTED
           MCS 5.................................... SUPPORTED
           MCS 6.................................... SUPPORTED
           MCS 7.................................... SUPPORTED
           MCS 8.................................... SUPPORTED
            MCS 9.................................... SUPPORTED
           MCS 10................................... SUPPORTED
           MCS 11................................... SUPPORTED
           MCS 12................................... SUPPORTED
           MCS 13................................... SUPPORTED
           MCS 14................................... SUPPORTED
           MCS 15................................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
    --More or (q)uit current module or <ctrl-z> to abort
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 ..........

    Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
    Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
    There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
    Sent from Cisco Technical Support iPhone App

  • Restore database in the same server but with other sid (name)

    i try to restore the database in the same server but with other sid (name) . The backup is on tape and
    I want to know the steps I should follow.
    thank.

    To perform restore of database in same host to choose another DB name you can go for
    1) duplicate using RMAN.
    Directory structure should be different so take care of db_file_name_convert & log_file_name_convert parameters
    Also check the Tns services exactly is it pointing to target & auxiliary
    http://www.shutdownabort.com/quickguides/clone_rman.php
    http://www.oracle-base.com/articles/9i/DuplicateDatabaseUsingRMAN9i.php

  • Creating same files on Different FTP Locations

    Hi All,
    My scenario is like this
    IDOC which is coming from SAP has to be sent to two FTP locations (XYZ20082210.dat both same structures)...
    Can any one please give me the best approach to handle this...
    I know i can do this by creating in two ways
    1) Using 1:N mapping 
    but this also i dont think the right approach as i need to duplicated the same Message Type and rename into 2 Message Type and use in the 1:N mapping.
    2) creating 2 Message Mappings and two Interface mappings and two recievers ..
    But this one XI processess the Mappings two times which is not good as we recieve multiple Idocs at a time...
    Please suggest me a suitable approach for which way i can achieve by more Optmizing ...
    Thanks and Regards,
    sridhar reddy

    Hi Sridhar,
    If you want to work out this issue using OS command, then you configure your receiver file adapter to place the file in one folder say 'Source' . Let your two destinations be Target 1 and 2 in the network. Paste the below two lines in notepad, edit the path names and save as .bat extension.
    xcopy D:\Source\.* "
    NetworkPath\Target1"*
    xcopy D:\Source\.* "
    NetworkPath\Target2"*
    If you receiver folders are in Windows network :
    You should run the above mentioned bat file to copy your messages to the destination in network.
    Note :  XI can NOT execute a OS command/ shell script on the receiver FTP server. The OS Command for the file adapter only runs on the system in which the Adapter Framework is running.
    If you receiver folders are in FTP Server :
    Refer this link : 
    http://www.circa.ufl.edu/handouts/networks/ftp.html

  • How to create Same File Name in Recever side

    Hi Frnds,
    1)In my sender side i am having one XML file Name:  vendor123.xml
    i have to send this file to receiver side with same file name, what are setting i need to do in file adapter.
    In receiver side i dont have any file, i have to crete with same file name.
    2)
    In my scenario my message interface name Vendor123_mt.
    In receiver side my file name should be Vendor123_mt, How to do handle this situation.
    Regards,
    Raja Sekhar

    Hi Raja,
    Regarding you 1st question: It can be easily achieved using the Adapter specific Message Attributes. You can refer the Michal's blog for it.
    /people/michal.krawczyk2/blog/2005/11/10/xi-the-same-filename-from-a-sender-to-a-receiver-file-adapter--sp14
    Regarding your 2nd question:
    Here you will need to use Variable Substitution. Use the following link:
    http://help.sap.com/saphelp_nw70/helpdata/EN/ae/d03341771b4c0de10000000a1550b0/frameset.htm
    Hope it helps.
    Regards,
    Sanjeev.

  • Sender File Adapter picking the same file twice

    We are facing a weird issue with File Sender Adapter
    We are using PI File Adapter ( NFS ) to read files for a NFS folder and
    processing those in PI.Normally it works fine. But for a scenario we
    are noticing it sometimes process the same file twice before archiving,
    thus duplicating the financial postings.
    What we have is :
    File Sender Adapter - NFS, Polling interval 60 secs, and Processign
    mdoe Archive. File name includes Wildcards - JE_Upload*.txt
    what we are noticing is that :
    when it picks up a file, it immediately polls again to check for
    another file, and sometimes the file is not yet archived so it picks up
    and reprocess the same file.
    If you see the message below, both belong to the same file, and it
    picked up the same file again in 12 secs after processing it the first
    time
       Successful 02.11.2009 15:01:00 02.11.2009 15:01:01   APMANUAL     urn:bl:i2g:003:100
    SI_SKF_FIDOC_OB XI Message
       Successful 02.11.2009 15:00:49 02.11.2009 15:00:50   APMANUAL     urn:bl:i2g:003:100
    SI_SKF_FIDOC_OB XI Message
    Anyone seen this behavior before?

    Hi,
    Please check the script which creates file in source NFS Folders. There is possibility that script is making change in file when PI is picking up the file.
    When PI picks the file first time it creates one message ID in system. After that if script is making any change in file without file name change (This need not necessary data change), for PI it becomes new file and new message gets generated in PI for same file.
    This error normally comes when File adapter is not able to archive file succesfully. For eg. file with same name alredy exists in Archive folder.
    File adapter generates the new message id whenfile get modified(eg.change in its length or data change) even though
    the file name is same and when file get change ,XI file adapter thinks that its new file and hence generate the new message id for same file.
    If file has same name and notmodified then XI adapter will not generate new message id and will keep on throw the error till you remove that file with same name from the
    archieve directory.
    -Warm Regards,
    Gouri

  • How to pick the sender files dynamically using the same File CC

    hi,
    My requirements is like , Same Sender File communication Channel has to pick up the different file which are having differnt file conventions and which are placed in different directories .. then it has to send to diffentn directories in the receiver side..
    how to do this?
    Regards,
    Balaji

    Hi Stefen,
    They have tried the Generic Sender File adapter concept to handle filenames with different names and from different directories instead creating many file channels. In my project many channels are configured as generic File sender channel.. And Eventhough the Generic file sender channels processing the filenames from different directories, all processed files are archieved in one common directories.. now they wanna generic solution to archieve the processed files in a particular folder based upon the directories they got processed from....
    and There are no such message mapping or Operation mapping since they used AAE concept. So do you  have any idea to make Generic File sender channels to archieve the files as per requirements i said before??
    Two doubts can we use like Module programming or can we do any OS level command acchieve this ? if yes please explain in detail .... Please help me out here
    please refer the following link .. exact way we used in our project
    http://wiki.sdn.sap.com/wiki/display/XI/SingleSenderFileCCForMultipleDirectories
    Regards,
    Balaji
    Edited by: Balaji Pichaimuthu on Feb 5, 2010 5:55 AM

  • How can I access a response file on the same computer but with different login?

    When trying to access a response file on the same computer that was used to set it up, but with a different login, I get an error message that the network resource was not found. How can I retrieve the responses on the same computer but under a different login/username?

    The response file is associated with a specific login (as determined under Edit > Preferences > Identity) so you cannot retrieve it if you're using a different login.

  • MATMAS05 Idoc to Flat File : Multiple material into same file

    Hi ,
      I am struck in simple scenario .Sending Materail Master data to flat file using idoc MATMAS05.  I made following changes to MATMAS05.xml file.
    I added MaxOccurs -=Unbounded and imported it in the interface mapping.
    <?xml version="1.0" encoding="UTF-8"?>
    <xsd:schema xmlns:xsd="http://www.w3.org/2001/XMLSchema"><xsd:element name="MATMAS05"><xsd:complexType><xsd:sequence><xsd:element name="IDOC" type="MATMAS.MATMAS05" maxOccurs="unbounded"
    I am able to get multiple materials extracted in same file .However the XML fails to open the file completely saying there is error.
    Can anybody send me an xml file of Material Master having 2 matrials so I can compare it?
    Regards
    Prashanta

    Hello Prasanta,
    If I understand correctly you are sending MATMAS from SAP to File.
    And you want to split the Matmas into multiple files .
    If this is the case then do not change the Idoc field occurance on the target side. In the Message mapping , messages tab change the occurance of the target to unbounded.
    And use enhanced interface determination for the same.
    Cheers,
    Himadri

Maybe you are looking for