SCCM 2012 R2, DHCP and WDS and PXE same server

hi
I am using DHCP and PXE on same server and getting error PXE-E55: proxyDHCP did not reply to request on port 4011

HI,
To get WDS and DHCP to work on the same machine, you need to configure WDS to share the same server as DHCP, here is how it is done.
You must have a functioning DHCP server with an active scope. WDS will utilize PXE which requires a DHCP server.
Whether you plan to co-host WDS and DHCP on the same server or use two different servers you must configure WDS to listen on a specific port. DHCP and WDS both require port number 67. If you have co-hosted WDS and DHCP you can move DHCP or the PXE site role
to a separate server or use the procedure below to configure the WDS server to listen on a different port.
Modify the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WDSServer\Providers\WDSPXE              
Set the registry value to:
UseDHCPPorts = 0              
For the new configuration to take effect run the following command on the co-located DHCP and WDS server:
WDSUTIL /Set-Server /UseDHCPPorts:No /DHCPOption60:Yes
https://technet.microsoft.com/en-us/library/bb680753.aspx
-- My System Center blog ccmexec.com -- Twitter
@ccmexec

Similar Messages

  • How to install both solution manager and ECC Development on same server

    Hi All,
    Can anyone help me how to install Solution Manager and ECC Development on same server and also whether SLD is required? if yes, then how to setup.
    Pls let me know.
    Regards,
    Karthik

    Hi Karthik,
    I try to answer you message, my answer may not be sufficient for you.
    Install SAP Solution Manager and ECC development as separate systems sharing the same server. So each system will get it's own system id and installation number.
    Verify sizing of both systems.
    SLD is not mandatory for a SAP Solution Manager. If a SLD already exist in your System Landscape, you can connect SMSY (System Landscape) in transaction SMSY_SETUP with a SLD. Information on System will then be retrieved from SLD, rather via an RFC.
    Best regards,
    Ruediger Stoecker

  • How to Install R/3 and CRM on the same Server?

    Hi All,
    I would like to install R/3 and CRM on the same server (as the load is less). I know how to install them seperately.
    I would like to have some instructions how to have them installed on the same server.
    Thanks in advance.
    Regards,
    Vijay

    As Sunil explained - MCOD (or) you can think to have 2 differnt DB SID's as weel 2 different SAP SID's. By default 1st Installation takes Listener Name as LISTENER & port 1527 when you are doing second Oracle installation use another lister name as LISTENER002 & give port 1526 ( for example).
    MCOD will be the best option to unplug from oracle instalation requirement but - think of future plans. even it can be any size business don't think to do MCOD with SAP Business System like R3 .
    Becuase qwe may have different requirements from the Business / functionla Team for refreshing / building the development system with a copy of production system - don;t get confused there are Techniques for Refreshing a Development Instance with production system also.
    Any how you have to take decission to go with MCOD (or) not . I also request SUNIL to comment on MCOD installations  with R3 system .
    But  I beleive Sascha Version is wrong - i can have multiple application servers of differnet products on single Box if my OS supports.
    as application servers will have 3 individual mount point which points to different system
    <Central Instance>:/sapmnt/<SID>/global
    <Central Instance>:/sapmnt/<SID>/prfoile
    <Central Instance>:/sapmnt/<SID>/exe
    each SID  NFS mount point can point to different sever & i can multiple application server of differnt SAP Products on 1 BOX.
    Trans directory is problem - but it does not require either for installation (or) for runningAS instance .

  • Installation of EBS 12.1 and Database on the same server

    Hi,
    Due to resource crunch, I would like to do new installation of EBS 12.1 and Database on the same server where already EBS 12.1 and Database installed.
    I have one server where EBS 12.1 and Database installed (Single node installation).
    Now I want to create another environment for other purpose (another test env.). But I don't have another server .
    So Can I start new installation of EBS 12.1 and database on the same server ?
    I have enough space and memory on server.
    Are the installtion conflict with each other ? any implications happen on the first environment ?
    I want my first environment run fine without any prob., after installing EBS and DB on the same server.
    Please guide me.
    Regards,
    Sanjay Patel

    So Can I start new installation of EBS 12.1 and database on the same server ?
    I have enough space and memory on server.Yes you can as long as you have sufficient resources.
    Are the installtion conflict with each other ? any implications happen on the first environment ? If you install in different ORACLE_HOMEs you should be OK.
    Thanks,
    Hussein

  • Upgrade to SCCM 2012 R2: WinPE 5.0 and Legacy system.

    Hi,
    When upgrade to SCCM 2012 SP1 we get WinPE 4.0 boot images, and the PXE-boot did not working with CPU's that do not support NX/PAE/SSE2.
    SCCM 2012 R2 need "ADK for Windows 8.1" with WinPE 5.0. I think it is same with WinPE 5.0 that it dont working with CPU's that do not support NX/PAE/SSE2.
    Is there something else to considerations with WinPE 5.0 boot with Legacy systems?
    ref:
    http://blogs.technet.com/b/configmgr_geek_speak/archive/2013/03/03/winpe-4-0-boot-images-not-working-with-cpu-s-that-do-not-support-n
    /SaiTech

    I think the link you posted is broken, but this one works:
    http://blogs.technet.com/b/configmgr_geek_speak/archive/2013/03/03/winpe-4-0-boot-images-not-working-with-cpu-s-that-do-not-support-nx-pae-sse2.aspx
    You can still use WinPE3.1, for those legacy computers:
    http://blogs.technet.com/b/brandonlinton/archive/2013/06/21/how-to-create-and-import-a-winpe-3-1-boot-image-for-use-in-configmgr-2012-sp1-cu2.aspx
    http://technet.microsoft.com/en-us/library/dn387582.aspx
    http://technet.microsoft.com/en-us/library/hh397288.aspx
    Don
    (Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
    This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

  • SCCM 2012 R2 client version 1101 and 1104 queries

    There are several samples of collection query code for SCCM 2012 R2 client version 5.00.7958.1000, which is the base R2 client version. Patches can change this to 5.00.7958.1101 and 5.00.7958.1104. But there is a problem. These two patches
    display as 1101 and 1104 when you go to Control Panel\Configuration Manager\General tab but when you go to Programs and Features and look in there the DisplayVersion is 5.00.7958.1000--so all query code samples are unable to different between the base versions
    and version 1101 and 1004. I have been unable to find out how to write a query that finds version s 1101 and 1104. Does anyone know how to do this? Thanks.

    Use ClientVersion from SMS_R_System within a console query or ClientVersion0 from V_R_system in a SQL query.
    Even this can be deceptive though because the agent only reflects the highest version number of one of its subcomponets. This post, specific to 2007, describes the complexity: http://blog.configmgrftw.com/configmgr-client-hotfix-versioning/.
    Specific to your question though, why do you care if either of these hotfixes are distributed to your clients? 2905002 is only necessary during WinPE (and if you are actually not using download on demand content during OSD) and 2910552 is only applicable
    if you are rolling out Win 8.1 using a single TS to your XP systems using a refresh methodology.
    Jason | http://blog.configmgrftw.com

  • Software Asset Management Solution Accelerator for SCCM 2012 (Contracts, Licenses, Userights, Installations and net usage

    Hello All
    With the given need from the market to manage license compliance proactively - the givven toolsets from MS SCCM 2012 should be capable of handling the given complexity. (reference 27 processes out of SAM ISO 19.770-1:2012
    Where can I find the solution accelerator, which guides us to help clients on two tipical use-cases
    a.) Client has SCCM 2012 - however not yet established the SAM componentes to it (Contracts, Use-rights and License-Comparizons)
    b.) Client has no SCCM yet and wants to start his journey with the Commercial scope right away.
    Any guidance highly appreciated

    SCCM alone isn't going to fit this need.
    You need a License Compliance Solution / Software Asset Management (SAM) solution which SCCM is not.
    The issue with those system, they fail of providing clean /usefull data.
    Usually the best approach is to collect the data with SCCM, normalize the data for that I used BDNA Normalize, then pull in the SAM.
    Like this:
    SCCM 2012 - Normalize - SAM
    John Marcum | http://myitforum.com/myitforumwp/author/johnmarcum/

  • Is there Java API available for third-party integrations with SCCM 2012? I went through the "Developer's Survival Guide", and it seems that SCCM 2012 SDKs only support C# and PowerShell

    Hi All,<o:p></o:p>
    My team and I are developing a software using java that works closely with IT management software such as SCCM. Our software will be highly dependent on data stored in SCCM. Basically
    our software will talk to SCCM to get information about a system managed by SCCM. To be able to do that, our software needs to use a java API that talks to SCCM. Is there a java API for SCCM 2012 that we can use? If there is not, what is the work around to
    this issue (integrate a java project with SCCM SDKs)? Any help is appreciated! Thanks!<o:p></o:p>

    Hi,
    As you mentioned, it seems that there is no available Java API for SCCM .
    Just curious, what's information you want to get from SCCM.
    Based on my experience, you could query the SCCM site database to get almost all the information.
    Otherwise, your question seems to be related to SCCM 2012. You may also choose to post there to get more effictive help.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Does sccm 2012 supports ibcm for linux and unix operating systems

    folks,
    does SCCM 2012 supports linux and unix operating system for IBCM ..........as per my knowledge it dont what i have learn t through bing........

    I thought it's not supported for Linux and Unix, see also:
    http://blogs.msdn.com/b/teju_shyamsundar/archive/2014/05/23/installing-the-system-center-2012-r2-configuration-manager-client-on-linux-part-2.aspx
    My Blog: http://www.petervanderwoude.nl/
    Follow me on twitter: pvanderwoude

  • Orchestrator and SCCM 2012 integration: run task sequence and install assigned applications/packages?

    Dear,
    We do not have Orchestrator running in our SCCM 2012 R2 environment. Though I wonder if we could accomplish the following scenario with it:
    Task sequence Windows 7 => Orchestrator step which queries assigned installations to the computer object and installs them one by one.
    Could you advise?
    Kind regards,
    Stev.
    SteveWonB

    > > Define "assigned to computer objects". How is this done technically?
    Well, computer objects are members of collections via AD memberships, like the collection "W7-Google-Chrome" (exists of 100 computer objects).
    Deploy of packages is done to these collections. So a computer member of  "W7-Google-Chrome"  will automatically get Google Chrome.
    Some computers are member of 30 collections, some of 80.
    Goal is to have the task sequence run all applications/packages assigned (with their reboots if needed).
    Kind regards,
    Steven
    SteveWonB

  • SCCM 2012 Client - Powershell to Patch and Reboot

    Powershell script to install all outstanding security patches and reboot server having sccm 2012 client.
    ([wmiclass]'ROOT\ccm\ClientSDK:CCM_SoftwareUpdatesManager').InstallUpdates([System.Management.ManagementObject[]] (Get-WmiObject -Query 'SELECT * FROM CCM_SoftwareUpdate' -namespace 'ROOT\ccm\ClientSDK')); 
    while (!((gwmi -Namespace 'ROOT\ccm\ClientSDK' -Class 'CCM_ClientUtilities' -list).DetermineIfRebootPending().RebootPending)){
    Write-Host "Patching";Start-Sleep -s 120;
    if((gwmi -Namespace 'ROOT\ccm\ClientSDK' -Class 'CCM_ClientUtilities' -list).DetermineIfRebootPending().RebootPending)
    {(Get-WmiObject -Namespace 'ROOT\ccm\ClientSDK' -Class 'CCM_ClientUtilities' -list).RestartComputer()}

    If your clients are member of an Active Directory, you could also use a startup script to update the client.
    Jason has a very popular script you can use:
    http://blog.configmgrftw.com/configmgr-client-startup-script/
    Ronni Pedersen | Microsoft MVP - ConfigMgr | Blogs:
    www.ronnipedersen.com/ and www.SCUG.dk/ | Twitter
    @ronnipedersen

  • SCCM 2012 NAP Agent goes in and out of compliance approx every 2 min.

    I have deployed the SCCM 2012 NAP Agent on a few clients and it goes in and out of compliance approx every 2 min.
    So its compliant for 2 min then uncompliant for about 30 sec then compliant again. If I uninstall the single software update I have enforced with NAP on SCCM the update is remediated properly by NAP/SCCM but the cycling in and out of compliance continues.
    I did have the agent in sccm set to 2 min evaluation cycle for testing purposes but have now reverted it back to one day.  The Health Validation Point is set to 26hrs.
    tconners

    I reset the sccm NAP evaluation cycle again to 1 day and it took this time.
    I cant explain why it was still stuck on 2 min.
    tconners

  • Does anyone worked with SCCM 2012 with 1E shopping, Appclarity and Nomad

    HI all
    Is there any blog available for learning 1E products with sccm 2012?
    thanks in advance.

    1E blog site is here: http://blogs.1e.com/; however, for "learning" about 1E products, well that is something different. Our public product content is fairly high level, in an "overview" model of features and basic functions.
    You can find added info for each product on the core 1E web site under each product's subsection:
    Shopping: http://www.1e.com/shopping/. Note thee details on our newly achieved formal certification for ServiceNow integtration and the link to a "live" demo.
    AppClarity: 
    http://www.1e.com/appclarity-software-asset-management/
    Nomad: http://www.1e.com/nomad/
    NightWatchMan: http://www.1e.com/nightwatchman/
    Lastly, the Resource Center (http://www.1e.com/resource-center/0 has a wealth of case studies, white papers and so on that may be of interest.
    I'm a pre-sales technical solutions engineer, so feel free to reach out to me directly if I can be of any additional assistance in any way (Ed.Aldrich @ 1e.com)
    Ed Aldrich | 1E | Pre-Sales Solutions Engineer | ConfigManager MVP 2003-2012

  • Problem installing SCCM 2012 R2 Hotfix KB2905002 (WDS/OSD slowness issue)

    Hi everyone!
    Tried installing
    KB2905002 yesterday and although the update did get applied to our Primary, we get the following error when the hotfix attempts to create the Console and Client update packages...
    Here is the error from the log...
    "Task 'Create Software Update Catalog' completed, state is 'failed' ExceptionText: Error: Setup detected an unexpected problem during installation. Error message: A valid file name is required.
    Parameter name: fileName
    Error: Setup detected an unexpected problem during installation. Error message:    at Microsoft.SystemCenter.UpdateSetup.SystemUtilities.CalculateSHA1Base64(String fileName)
       at Microsoft.SystemCenter.UpdateSetup.Tasks.GenerateCatalog.ReplaceCommonInsertionStrings(String startText, String packageFile)
       at Microsoft.SystemCenter.UpdateSetup.Tasks.GenerateCatalog.GetServerUpdateXml()
       at Microsoft.SystemCenter.UpdateSetup.Tasks.GenerateCatalog.DoRun()
       at Microsoft.SystemCenter.UpdateSetup.Tasks.GenericTask.RunThread(Object taskObject)"
    Anyone have any ideas?
    Regards,
    JJ

     got the same problem this mostly happens if you re install the SCCM R2 due to any reason and you previously installed these Hot fixes too. IF you focus on the wizard deeply you got this message prior to error page Regard less of KB2910552 obvs on your
    screen you will see KB2905002. So the solution is
    1.Go to your "control panel" on your Primary site server
    2. Open "Program and Features" 
    3. Click oon "View installed Updates" on left pane.
    4.  Scroll down to the installed KBs of "System Center 2012 R2 Configuration Manager" 
    5. Uninstall you desired KB
    6. Try to install again by setup. Hope this time you will not get the error message.

  • Exchange 2013 Windows Server 2012 NLB and DAG on the same server

    Hi all, I am installing Exchange 2013 infrastructure with two servers. 
    Both servers have the CAS and Mailbox roles. 
    For mounting on High Availability, will create a DAG. 
    Client Access I have no external Network Load Balancer. 
    I thought about installing the NLB servers in the DAG members, this could not be done before. 
    I do not know if in Windows Server 2012 and Exchange 2013 
    Can I install NLB on members of a DAG? 
    regards
    Microsoft Certified IT Professional Server Administrator

    Hi,
    I’m afraid that WNLB and DAG cannot coexist in the same server. Because WNLB is incompatible with Windows failover clustering. If we're using an Exchange 2010 DAG and we want to use WNLB, we need to have the Client Access server role and the Mailbox server
    role running on separate servers.
    For more information, you can refer to the following article:
    http://technet.microsoft.com/en-us/library/ff625247(v=exchg.141).aspx
    Thanks,
    Angela Shi
    TechNet Community Support

Maybe you are looking for