Setxkbmap no gives: Error loading new keyb.

I had this problem a while ago. I run pacman -Suy and updated everything. That fixed the problem. But a few days ago when i updated again, the problem came back. I'm not quite sure what was updated, but I did a -Suy. Running x.org.
Anyone have any idea what the problem might be?

Now, this is getting annoying. This is the fourth time it's back.
When I'm starting X I get the following output:
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Error: bad length in CompatMap
> Output file "/var/tmp/server-0.xkm" removed
Errors from xkbcomp are not fatal to the X server
(EE) Couldn't load XKB keymap, falling back to pre-XKB keymap
And again, it's only affecting users and not root. Have been searching around for some time without luck.
Any ideas?
This is what my xorg.conf says:
Section "InputDevice"
Identifier "Keyboard1"
Driver "kbd"
Option "AutoRepeat" "500 30"
Option "XkbRules" "xorg"
Option "XkbModel" "pc101"
Option "XkbLayout" "us"
EndSection
It came after the following upgrade
[03/17/05 09:26] upgraded arts (1.3.2-1 -> 1.4.0-4)
[03/17/05 09:26] upgraded atk (1.9.0-1 -> 1.9.1-1)
[03/17/05 09:26] upgraded db (4.2.52.2-2 -> 4.3.27-2)
[03/17/05 09:26] upgraded evolution (2.0.3-2 -> 2.2.0-1)
[03/17/05 09:26] upgraded evolution-data-server (1.0.3-2 -> 1.2.0-1)
[03/17/05 09:26] upgraded gal (2.2.4-1 -> 2.4.0-1)
[03/17/05 09:26] upgraded gconf (2.8.1-1 -> 2.10.0-1)
[03/17/05 09:26] upgraded gecko-sharp (0.6-2 -> 0.6-3)
[03/17/05 09:26] upgraded gnome-common (2.8.0-8 -> 2.8.0-9)
[03/17/05 09:26] upgraded gnome-keyring (0.4.1-1 -> 0.4.2-1)
[03/17/05 09:26] upgraded gnome-vfs (2.8.3-4 -> 2.10.0-1)
[03/17/05 09:26] upgraded gthumb (2.6.3-1 -> 2.6.4-2)
[03/17/05 09:26] upgraded gtkhtml (3.2.4-1 -> 3.6.0-1)
[03/17/05 09:26] upgraded gtk-sharp (1.0.6-1 -> 1.0.8-1)
[03/17/05 09:26] upgraded gtksourceview (1.1.1-1 -> 1.2.0-1)
[03/17/05 09:26] upgraded heimdal (0.6.3-2 -> 0.6.3-3)
[03/17/05 09:26] upgraded k3b (0.11.20-1 -> 0.11.21-1)
[03/17/05 09:26] installed jasper (1.701.0-1)
[03/17/05 09:26] warning: /opt/kde/share/config/kdm/kdmrc saved as /opt/kde/share/config/kdm/kdmrc.pacorig
[03/17/05 09:26] warning: /opt/kde/share/config/kdm/backgroundrc saved as /opt/kde/share/config/kdm/backgroundrc.pacorig
[03/17/05 09:26] installed kde-common (3.4.0-6)
[03/17/05 09:27] upgraded kdelibs (3.3.2-5 -> 3.4.0-5)
[03/17/05 09:27] installed gstreamer (0.8.9-1)
[03/17/05 09:27] upgraded kdeaccessibility (3.3.2-1 -> 3.4.0-4)
[03/17/05 09:27] installed cyrus-sasl (2.1.20-2)
[03/17/05 09:27] installed sysfsutils (1.2.0-1)
[03/17/05 09:27] installed pmount (0.6-1)
[03/17/05 09:27] upgraded kdebase (3.3.2-4 -> 3.4.0-5)
[03/17/05 09:27] upgraded kdepim (3.3.2-2 -> 3.4.0-5)
[03/17/05 09:27] installed gst-plugins (0.8.8-1)
[03/17/05 09:27] upgraded kdemultimedia (3.3.2-1 -> 3.4.0-4)
[03/17/05 09:27] upgraded kdegames (3.3.2-1 -> 3.4.0-4)
[03/17/05 09:27] upgraded kdeaddons (3.3.2-3 -> 3.4.0-5)
[03/17/05 09:27] upgraded kdeadmin (3.3.2-1 -> 3.4.0-5)
[03/17/05 09:28] upgraded kdeartwork (3.3.2-1 -> 3.4.0-4)
[03/17/05 09:28] upgraded kdebindings (3.3.2-3 -> 3.4.0-5)
[03/17/05 09:28] upgraded kdeedu (3.3.2-1 -> 3.4.0-4)
[03/17/05 09:28] upgraded kdegraphics (3.3.2-3 -> 3.4.0-4)
[03/17/05 09:28] installed qca (1.0-1)
[03/17/05 09:28] installed qca-tls (1.0-1)
[03/17/05 09:28] installed perl-net-ssleay (1.25-1)
[03/17/05 09:28] installed perl-io-socket-ssl (0.95-1)
[03/17/05 09:28] upgraded kdenetwork (3.3.2-1 -> 3.4.0-5)
[03/17/05 09:28] upgraded kdesdk (3.3.2-2 -> 3.4.0-5)
[03/17/05 09:28] upgraded kdetoys (3.3.2-1 -> 3.4.0-4)
[03/17/05 09:28] installed net-snmp (5.2.1-1)
[03/17/05 09:28] installed dosfstools (2.10-1)
[03/17/05 09:28] upgraded kdeutils (3.3.2-1 -> 3.4.0-5)
[03/17/05 09:29] upgraded kernel26 (2.6.10-3 -> 2.6.11.3-1)
[03/17/05 09:29] upgraded libbonoboui (2.8.1-1 -> 2.8.1-2)
[03/17/05 09:29] upgraded libgda (1.2.0-1 -> 1.2.0-2)
[03/17/05 09:29] upgraded libgnome (2.8.0-1 -> 2.10.0-1)
[03/17/05 09:29] upgraded libgnomecanvas (2.8.0-1 -> 2.10.0-1)
[03/17/05 09:29] upgraded libgnomeprint (2.8.2-1 -> 2.10.1-1)
[03/17/05 09:29] upgraded libgnomeprintui (2.8.2-1 -> 2.10.1-1)
[03/17/05 09:29] upgraded libgnomeui (2.8.0-2 -> 2.10.0-1)
[03/17/05 09:29] upgraded librsvg (2.8.1-3 -> 2.9.5-1)
[03/17/05 09:29] upgraded liferea (0.9.0b-2 -> 0.9.1-1)
[03/17/05 09:29] upgraded openldap (2.2.23-1 -> 2.2.23-2)
[03/17/05 09:29] upgraded pam (0.78-3 -> 0.78-4)
[03/17/05 09:29] upgraded pango (1.8.0-1 -> 1.8.1-1)
[03/17/05 09:29] upgraded perl (5.8.6-1 -> 5.8.6-2)
[03/17/05 09:29] upgraded python (2.4-2 -> 2.4-3)
[03/17/05 09:30] upgraded qt (3.3.4-3 -> 3.3.4-5)
[03/17/05 09:30] upgraded ruby (1.8.2-3 -> 1.8.2-4)
[03/17/05 09:30] upgraded startup-notification (0.7-1 -> 0.8-1)
[03/17/05 15:37] synchronizing package lists
[03/17/05 15:38] starting full system upgrade
[03/17/05 15:38] upgraded gal (2.4.0-1 -> 2.4.1-1)
[03/17/05 15:38] upgraded gtkhtml (3.6.0-1 -> 3.6.1-1)
[03/17/05 15:38] upgraded libsoup (2.2.2-1 -> 2.2.3-1)

Similar Messages

  • Creating new analysis gives "Error loading XML Document from ..."

    Trying to create analysis and getting "Error loading XML Document from saw.dll/answers/answersproperties.xml?fmapId=S1clug.
    The response given was:" after choosing subject area. Analysis editor is opened but Subject Areas is empty and can't do anything.
    The problem is on Mozilla 12 (16.0.2, 17.0.1) and IE 8. Chrome works fine.
    My system is Win 7, BI 11.1.1.6.0 is on Oracle Linux (and by the way Mozilla from Linux system works fine)
    What could be the reason of this?
    Edited by: 898973 on 4/12/2012 15:11

    Reinstalling Mozilla with "Remove personal data" option checked resolved the problem.

  • Key figure definition in BEx gives "Error loading template 0QUERY_TEMPLATE"

    Hi,
    On a BI 7.0 system I try to run a query in the BEx Analyzer and after I have the result in Excel. I wants to see the key figure definition by right clicking in a data cell.
    Then I get this error message after the browser has started up.
    Error loading template 0QUERY_TEMPLATE
    Notification Number BRAIN 276  
    Any ideas how this can be?
    Kind regards, Bjarne

    hi,
    Please check the below path in BI and set the template "0ANALYSIS_PATTERN" there:
    SPRO ->SAP Netweaver -> BI ->Settings for reporting and analysis ->BEX Web -> Set Standard Web Templates -> Ad-hoc analysis -> set the above template and save it.
    check wether it works afterwords or not.
    This is the standard web template called every time when we execute our query's.
    Thanks
    Dipika

  • Sapdba gives error after new QAS system build from PRD

    Hello All,
    I brought up a new QAS system by  copying oracle and sap executables, followed by restore from online backup. The system is up and running and sap is also up.
    When i try to execute sapdba, I get the follwoing error:
    <b>/usr/lib/pa20_64/dld.sl: Unable to find library 'libclntsh.sl.8.0'.
    Segmentation error.</b>
    other tools like svrmgrl and sqlplus works fine.
    Upon investigation i found that, i did not copy /oracle/client and that is causing this error.
    I copied the following /oracle directories
    /oracle/SID
    /oracle/version_number
    /oracle/stage
    I did not copy the following directories
    /oracle/client
    /oracle/oraInventory
    /oracle/jre
    /oracle/oui
    Since the system is up and running already , is it ok for me to copy the left out directories now? Also are they all needed essentially or just /oracle/client is enough.
    Please help me as this is very urgent task. Any help with be greatly appreciated with points.
    Thanks,
    Basis learner

    Hello,
    you can extract oracle client SAR archive in you /oracle/client, in order to be sure to have the right oracle client files.
    you will find SAR archive in download section of SAP support portal.
    Regards
    Ermanno

  • AdobeInDesign7_5_2_Patch-All gives "Error loading updater workflow"

    InDesign CS5.5 Version 7.5.0.142
    Any ideas please?
    Thanks.

    Mmh, if the program works okay, then it's probably one of those installer database blockages. Short of uninstalling everything, running the Creative Suite Cleaner Tool and reinstalling from scratch, this is usually impossible to fix, but you might provide the install logs and perhaps we can find soem clue in there.
    Mylenium

  • Netflix error loading content

    Netflix gives "error loading content"
    Thoughts to correct?

    I had the issue back in November & December where it was working however the quality was horrible.  That was fixed and now I'm getting the "An error occurred loading this content" as well.  Netflix is working great on my iPad so I tried to stream it using the Airplay and ended up with the same error. 
    Anyone called Netflix?  I'm on hold right now.  Odd's are they're going to blame Apple.

  • Error loading java applet

    I downloaded and installed j2se_1.4.1. Now every time I go to a site which needs the java applet, it gives "error loading java applet" (or something like that). I already uninstalled it and reinstalled it, but I keep getting that error. Can someone help me out please??
    I use win XP home and Internet Eplorer 6
    thanx

    I also have the same problem!
    can someone help us PLEASE ?!!!

  • Loading big XML files using JDBC gives errors

    Hi,
    I've created a XMLType table using binary storage, with the restriction that any document stored has a (any) schema:
    CREATE TABLE XMLBIN OF XMLTYPE
    XMLTYPE STORE AS BINARY XML
    ALLOW ANYSCHEMA;Then I use JDBC to store a relatively large document using the following code:
    Class.forName("oracle.jdbc.driver.OracleDriver").newInstance();
    String connectionString = "jdbc:oracle:thin:@host:1521:sid";
    File f = new File("c:\\temp\\big.xml");
    Connection conn = DriverManager.getConnection(connectionString, "username", "password");
    XMLType xml = XMLType.createXML(conn,new FileInputStream(f));
    String statementText = "INSERT INTO xmlbin VALUES (?)";
    OracleResultSet resultSet = null;
    OracleCallableStatement statement = (OracleCallableStatement)conn.prepareCall(statementText);
    statement.setObject(1,xml);
    statement.execute();
    statement.close();
    conn.commit();
    conn.close();Loading a file of 61Mb (real Mb, in non-IT Mb (where 1Mb seems to be 10^6) it is 63.9Mb) or less doesn't give any errors, loading a file bigger then that gives the following error:
    java.sql.SQLRecoverableException: Io exception: Software caused connection abort: socket write error
            at oracle.jdbc.driver.SQLStateMapping.newSQLException(SQLStateMapping.java:101)
            at oracle.jdbc.driver.DatabaseError.newSQLException(DatabaseError.java:112)
            at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:173)
            at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:229)
            at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:458)
            at oracle.jdbc.driver.T4CCallableStatement.executeForRows(T4CCallableStatement.java:960)
            at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1222)
            at oracle.jdbc.driver.OraclePreparedStatement.executeInternal(OraclePreparedStatement.java:3381)
            at oracle.jdbc.driver.OraclePreparedStatement.execute(OraclePreparedStatement.java:3482)
            at oracle.jdbc.driver.OracleCallableStatement.execute(OracleCallableStatement.java:3856)
            at oracle.jdbc.driver.OraclePreparedStatementWrapper.execute(OraclePreparedStatementWrapper.java:1373)
            at jdbctest.Tester.main(Tester.java:60)A succesful insert of a 63Mb file takes about 23 seconds to execute. The 70Mb file fails already after a few seconds, so I'm ruling out any time outs.
    I'm guessing there are some buffers that need to be enlarged, but don't have a clue which ones.
    Anyone any idea what might cause the problem and how to resolve?
    My server runs Oracle 11g Win32. The client is Windows running Sun Java 1.6, using ojdbc6.jar and Oracle 11g Client installed.
    Cheers,
    Harald

    Hi Mark,
    The trace log in the OEM shows me:
    Errors in file d:\oracle11g\app\helium\diag\rdbms\helium\helium\trace\helium_ora_6948.trc  (incident=7510): ORA-07445: exception encountered: core dump [__intel_new_memcpy()+613] [ACCESS_VIOLATION] [ADDR:0x0] [PC:0x6104B045] [UNABLE_TO_WRITE] []  If needed I can post the full contents (if I find out how, am still a novice :-))
    Cheers,
    Harald

  • Error loading control. a newer version needed. the default settings will be used

    Hi I am using LabVIEW DSC 7.1 for programming my application. My VI contains NI hypertrend which I am publishing on a browser using the web publishing tool. When I open the web browser on a different computer I get this error- Component works  Error loading Control. A newer version needed. The default settings for the control will be used. I have disabled firewall, pop up blocker etc...but for some reason it keeps giving me the same error. I read the knowledge base and it talks something about the .OCX file. I am not sure what I am supposed to do..I also have the DSC runtime installed in my machine. I'd appreciate it if someone could help me with this.

    If you're on a 64-bit OS, OCX files  must be in the folder: %windir% \ SysWOW64 
    and not in %windir% \ System32 (only for 32 bits OS)
    >> %windir% is  the environment variable that defines the Windows folder! (eg: C:\Windows)
    French version:
    Si tu es sur un OS en 64 bits, les fichiers .ocx doivent se trouver dans le dossier : %windir%\SysWOW64\
    et non pas dans %windir%\System32
    >> %windir% étant bien sur la variable d'environnement qui défini le dossier de Windows ! (par ex: C:\Windows)

  • "cwui"Error loading control. A newer version needed. The defaultsettings for the control will be used.

    各位先進:小弟最近在執行一個執行檔(.exe)時，跳出了"cwui"的視窗，上面寫著"Error loading control. A newer version needed. The defaultsettings for the control will be used."執行檔沒辦法動作，不知道是哪個地方出問題了...煩請各位解答我的苦惱之處!!感激不盡~

    請看看您的錯誤是否跟下面這個一樣
    http://digital.ni.com/public.nsf/allkb/627F8B1A99A72DBC862578770051FB9B
    若不是的話煩請提供您
    1. 錯誤訊息截圖
    2. 作業系統版本(是否是64-bit)
    3. LabVIEW版本
    4. 佈署端電腦所安裝的Runtime Engine版本
    5. 程式中有使用到的module或toolkit，例如：DSC, OPC server....等
    謝謝！

  • Firefox 8.0 loading MSN Homepage gives error 'problems loading page' every timebut the page eventually loads - Any solution?

    Firefox 8.0 gives error message "problem loading page" when loading MSN homepage. This occurs every time.
    The error is: "Firefox can't find the server at www.%3ciframe%20marginheight=%220%22%20marginwidth=%220%22%20name=%22wxbuttonframe%22%20id=%22wxbuttonframe%22%20height=%22283%22%20src=%22http.com."
    Is there a solution?

    I get an e-mail with go-comics and the ones I want to post links to I'll open in the browser as I read them in the e-mail so I regularly have a dozen tabs open (all the same site) by the time I'm through the e-mail. Every third or fourth page will hang up on something (connecting to or waiting for) sometimes not loading a single image, sometimes loading half the page, sometimes loading everything but the comic (because, hey, why put that as the first thing to load when you've got all these ads and crap to throw at your paying customers?).
    At some point a couple of months ago I got some malware associated with trovisearch (I do not know how that got past security and java blocker but it did, probably some hidden crap in something from CNET) that somehow spoofed a page for Housecall and added five or six pieces of malware and adware. I cleaned for two days after and still can't find anything left on the computer even though I've been running scans constantly to try to make Firefox work right. I downloaded and ran a scan using Kaspersky during that time and then uninstalled it. That very well may be the cause of the post-refresh SSL issue.
    I have Spybot and Malwarebytes scan logs from the time of the infection if that would help in any way. It doesn't look like there's a way to attach .xml files in this forum, though.
    I can also run hijack this and copy and paste if that would help.
    I'm currently running Windows Defender and rely on that and Noscript and adblocker plus to keep me isolated from most attacks (I don't have those add-ons re-installed yet). I also run Peerblock because they add malicious sites and known hacking sources (like Chinanet) to what they block as well as all the fake p2p stuff that's constantly pinging the computer. If I'm treading around in perilous waters I run Sandboxie.
    Chrome is working as normal but Firefox feels like dial-up or worse right now and without adblocker I might as well be using IE.

  • Error loading OS (first boot-up, new system, freeze at boot-up)

    I have built up a new system with:
    CPU: AMD3 Phenom II X4 945
    Board: MSI-7642 (890GXM-G65)
    Memory: DDR3 Dominator 2x2GB 1600Mhz
    Drive: SATAII 700GB Western Digital
    I am using the onboard graphics card
    I built the system up, turned it on and have the message:
    Error loading OS
    (the system then freezes on that message)
    at startup there is a single beep, the message "Error loading OS" is straight after the v890GXM-G65 splash. There is no BIOS message on the monitor, no RAM count, no chance to get into BIOS.
    Basically immediately after the MSI splash the error message shows.
    I would like to boot from my windows XP install CD and format the Hard-Drive and install Windows.
    After reading similar messages in the Forum I will:
    *reset the BIOS with the mainboard jumpers
    *set the Harddrive to SATA-I speed with the jumpers
    does anyone have any other suggestions?
    I don't have another PC that I can format my Harddrive on; it was formatted before simply with one partition (not a boot partition) as a backup drive.
    Seems to be a common problem, the "Error loading OS", pity MSI doesn't have a error code listing somewhere.

    I managed to sort the problem out.
    It seems that the BIOS system (Version 1.2) didn't accept hard drives when they are inappropriately formatted. It also had a problem with the USB Keyboard.
    I managed to sort this out by connecting SATA Harddrive that was used in my pervious system, which had windows XP already installed on it. Surprisingly this was not only accepted by the BIOS, I didn't have to reinstall Windows or any programmes at all - although the previous system ran on a Gigabyte Board, with a 939 socket AMD processor!
    Another problem was that my Keysonic Intuition-XL ACK-5600 USB2 keyboard wasn't accepted by the BIOS in the "new system state". Only after I had windows running, and the mainboard USB2 chipset drivers were installed in windows, was the USB2 keyboard accepted by windows or the BIOS. I couldn't connect a PS2 keyboard to the main board, because there is only one PS2 connector - which is taken be the mouse (more necessary for windows than a keyboard). Perhaps the BIOS had a problem with the keyboard, because it houses USB ports and audio connections.
    The conclusion:
    *The MSI-7642 (890GXM-G65) mainboard only accepted a SATA drive with a primary bootable partition. I couldn't start up with a Installation CD and install any drive.
    *The USB Keyboard didn't function during the BIOS boot until I installed the mainboard USB Chipset drivers in windows XP. This is strange, as normally the BIOS should be totally independent of the OS . The Keyboard itself doesn't need a windows driver.
     ;-))For a system builder it is advised to format SATA drives as primary bootable drives before building the system, and use a "simple" USB keyboard (with no electronic or ports), or better a PS2 Keyboard.

  • ITunes new version doesn't open at all. Gives error message

    I downloaded 7.4.3 version of iTunes and it doesn't open at all. Gives error message. "iTunes has encountered a problem and needs to close."
    I have previous version of iTunes in my spare HD, in the same computer, and it works perfectly fine.
    I have unistalled and re-installed again and again many times including with the help of Apple Support help in the phone and came up with no clues of what's going on.
    How can I get a previous version of iTunes to download to my PC? I have looking for a place on Apple's website where I could probably have my issue resolved, but I found nothing.
    Thank you.

    Thanks to Jim Zack, the problem is solved.
    If you're having this problem, go find the solution at the following page and read Jim's suggestion.
    http://discussions.apple.com/thread.jspa?threadID=1155613

  • Error message when starting Adobe Illustrator CC [Error loading plugins   AppBarControls.aip]

    Hello,
    I get the following error message when I start Adobe Illustrator CC.
    Error loading plugins
    AppBarControls.aip
    Then it gives me the option to continue by clicking okay. When it opens, the Application Bar is just blank.
    I've tried uninstalling, then ran Adobe CC Cleaner, then downloaded and reinstalled.
    Computer details : OS X 10.9.5, 1.3 GHz Intel Core i5, 8 GB 1600 MHz DDR3
    Help is kindly appreciated!

    I also have had a difficult time with Adobe Illustrator CC 2014 crashing upon launch.  The support staff was great even though we had to work through several sessions.  Below is the email explaining our final session.
    This email is in regards with the issue you had been facing with Illustrator CC 2014.
    While going through the installer logs, we found that there was an issue with the installation & the program installer had been denied access to several critical files & folders during installation.
    This was the main reason for Illustrator crash as several critical components had not been installed properly.
    We tried installing the program in a new user account & that worked.
    Though the program has been installed properly now & is working in your old account, I will still strongly recommend you to get your computer user account repaired with a Windows 7 operating system diskette.
    This is required so that you do not run into more trouble later while working with the Adobe Applications or even while installing other programs.
    Avanish Divya was the final support person that successfully resolved my problems.

  • Net.sf.jasperreports.engine.JRException: Error loading object from file : C

    I started using JasperReports for my web application report generation. I'm using JSPs for web development.
    I created a .jrxml file using iReport and used the following code to generate the report.
    try {
              JasperDesign jasperDesign = JRXmlLoader.load("C:\\tomcat\\webapps\\web\\JSP\\reports\\samples\\pmm-final.jrxml");
              JasperReport jasperReport = JasperCompileManager.compileReport(jasperDesign);
    // Second, create a map of parameters to pass to the report.
              Map parameters = new HashMap();
              parameters.put("Title", "JasperReport");
    // Third, get a database connection
              Connection conn = null;
              Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
              conn=DriverManager.getConnection("jdbc:odbc:driver={Microsoft Access Driver (*.mdb)};DBQ=C:/tomcat/webapps/db1/db1.mdb");
    // Fourth, create JasperPrint using fillReport() method
              JasperPrint jasperPrint = JasperFillManager.fillReport(jasperReport,
                                  parameters, conn);
    // You can use JasperPrint to create PDF
              //JasperExportManager.exportReportToPdfFile(jasperPrint, "C:\\tomcat\\webapps\\web\\JSP\\reports\\TestReport.pdf");
              JasperExportManager.exportReportToHtmlFile(jasperPrint, "C:\\tomcat\\webapps\\web\\JSP\\reports\\TestPMM.html");
              JRXlsExporter exporter = new JRXlsExporter();
              exporter.setParameter(JRExporterParameter.JASPER_PRINT, jasperPrint);
              exporter.setParameter(JRExporterParameter.OUTPUT_FILE_NAME, "C:\\tomcat\\webapps\\web\\JSP\\reports\\TestPMM.xls");
              exporter.exportReport();
    // Or to view report in the JasperViewer
              //JasperViewer.viewReport(jasperPrint);
    } catch (JRException e) {
              // TODO Auto-generated catch block
              e.printStackTrace();
    } catch (SQLException e) {
              // TODO Auto-generated catch block
              e.printStackTrace();
    The above pmm-final.jrxml uses a subreport 'top.jasper'. Error being thrown while loading top.jasper file. Error is as follows.
    java.io.InvalidClassException: net.sf.jasperreports.engine.base.JRBaseReport; lo
    cal class incompatible: stream classdesc serialVersionUID = 604, local class ser
    ialVersionUID = 606
    at java.io.ObjectStreamClass.initNonProxy(Unknown Source)
    at java.io.ObjectInputStream.readNonProxyDesc(Unknown Source)
    at java.io.ObjectInputStream.readClassDesc(Unknown Source)
    at java.io.ObjectInputStream.readNonProxyDesc(Unknown Source)
    at java.io.ObjectInputStream.readClassDesc(Unknown Source)
    at java.io.ObjectInputStream.readOrdinaryObject(Unknown Source)
    at java.io.ObjectInputStream.readObject0(Unknown Source)
    at java.io.ObjectInputStream.readObject(Unknown Source)
    at net.sf.jasperreports.engine.util.JRLoader.loadObject(JRLoader.java:86
    at net.sf.jasperreports.engine.util.JRLoader.loadObjectFromLocation(JRLo
    ader.java:236)
    at net.sf.jasperreports.engine.fill.JRFillSubreport.evaluate(JRFillSubre
    port.java:295)
    at net.sf.jasperreports.engine.fill.JRFillBand.evaluate(JRFillBand.java:
    340)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillPageBand(JRVert
    icalFiller.java:1224)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillPageHeader(JRVe
    rticalFiller.java:353)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillReportStart(JRV
    erticalFiller.java:205)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillReport(JRVertic
    alFiller.java:119)
    at net.sf.jasperreports.engine.fill.JRBaseFiller.fill(JRBaseFiller.java:
    613)
    at net.sf.jasperreports.engine.fill.JRBaseFiller.fill(JRBaseFiller.java:
    483)
    at net.sf.jasperreports.engine.fill.JRFiller.fillReport(JRFiller.java:77
    at net.sf.jasperreports.engine.JasperFillManager.fillReport(JasperFillMa
    nager.java:248)
    at org.apache.jsp.JSP.UserGuide_jsp._jspService(org.apache.jsp.JSP.UserG
    uide_jsp:74)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:99)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:802)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper
    .java:325)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:2
    95)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:245)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:802)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(Appl
    icationFilterChain.java:252)
    at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationF
    ilterChain.java:173)
    at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperV
    alve.java:214)
    at org.apache.catalina.core.StandardContextValve.invoke(StandardContextV
    alve.java:178)
    at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.j
    ava:126)
    at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.j
    ava:105)
    at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineVal
    ve.java:107)
    at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.jav
    a:148)
    at org.apache.jk.server.JkCoyoteHandler.invoke(JkCoyoteHandler.java:306)
    at org.apache.jk.common.HandlerRequest.invoke(HandlerRequest.java:385)
    at org.apache.jk.common.ChannelSocket.invoke(ChannelSocket.java:745)
    at org.apache.jk.common.ChannelSocket.processConnection(ChannelSocket.ja
    va:675)
    at org.apache.jk.common.SocketConnection.runIt(ChannelSocket.java:868)
    at org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadP
    ool.java:684)
    at java.lang.Thread.run(Unknown Source)
    NESTED BY :
    java.io.InvalidClassException: net.sf.jasperreports.engine.base.JRBaseReport; lo
    cal class incompatible: stream classdesc serialVersionUID = 604, local class ser
    ialVersionUID = 606
    at java.io.ObjectStreamClass.initNonProxy(Unknown Source)
    at java.io.ObjectInputStream.readNonProxyDesc(Unknown Source)
    at java.io.ObjectInputStream.readClassDesc(Unknown Source)
    at java.io.ObjectInputStream.readNonProxyDesc(Unknown Source)
    at java.io.ObjectInputStream.readClassDesc(Unknown Source)
    at java.io.ObjectInputStream.readOrdinaryObject(Unknown Source)
    at java.io.ObjectInputStream.readObject0(Unknown Source)
    at java.io.ObjectInputStream.readObject(Unknown Source)
    at net.sf.jasperreports.engine.util.JRLoader.loadObject(JRLoader.java:86
    at net.sf.jasperreports.engine.util.JRLoader.loadObjectFromLocation(JRLo
    ader.java:236)
    at net.sf.jasperreports.engine.fill.JRFillSubreport.evaluate(JRFillSubre
    port.java:295)
    at net.sf.jasperreports.engine.fill.JRFillBand.evaluate(JRFillBand.java:
    340)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillPageBand(JRVert
    icalFiller.java:1224)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillPageHeader(JRVe
    rticalFiller.java:353)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillReportStart(JRV
    erticalFiller.java:205)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillReport(JRVertic
    alFiller.java:119)
    at net.sf.jasperreports.engine.fill.JRBaseFiller.fill(JRBaseFiller.java:
    613)
    at net.sf.jasperreports.engine.fill.JRBaseFiller.fill(JRBaseFiller.java:
    483)
    at net.sf.jasperreports.engine.fill.JRFiller.fillReport(JRFiller.java:77
    at net.sf.jasperreports.engine.JasperFillManager.fillReport(JasperFillMa
    nager.java:248)
    at org.apache.jsp.JSP.UserGuide_jsp._jspService(org.apache.jsp.JSP.UserG
    uide_jsp:74)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:99)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:802)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper
    .java:325)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:2
    95)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:245)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:802)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(Appl
    icationFilterChain.java:252)
    at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationF
    ilterChain.java:173)
    at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperV
    alve.java:214)
    at org.apache.catalina.core.StandardContextValve.invoke(StandardContextV
    alve.java:178)
    at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.j
    ava:126)
    at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.j
    ava:105)
    at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineVal
    ve.java:107)
    at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.jav
    a:148)
    at org.apache.jk.server.JkCoyoteHandler.invoke(JkCoyoteHandler.java:306)
    at org.apache.jk.common.HandlerRequest.invoke(HandlerRequest.java:385)
    at org.apache.jk.common.ChannelSocket.invoke(ChannelSocket.java:745)
    at org.apache.jk.common.ChannelSocket.processConnection(ChannelSocket.ja
    va:675)
    at org.apache.jk.common.SocketConnection.runIt(ChannelSocket.java:868)
    at org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadP
    ool.java:684)
    at java.lang.Thread.run(Unknown Source)
    NESTED BY :
    net.sf.jasperreports.engine.JRException: Error loading object from file : C:\tom
    cat\webapps\web\JSP\reports\samples\top.jasper
    at net.sf.jasperreports.engine.util.JRLoader.loadObject(JRLoader.java:90
    at net.sf.jasperreports.engine.util.JRLoader.loadObjectFromLocation(JRLo
    ader.java:236)
    at net.sf.jasperreports.engine.fill.JRFillSubreport.evaluate(JRFillSubre
    port.java:295)
    at net.sf.jasperreports.engine.fill.JRFillBand.evaluate(JRFillBand.java:
    340)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillPageBand(JRVert
    icalFiller.java:1224)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillPageHeader(JRVe
    rticalFiller.java:353)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillReportStart(JRV
    erticalFiller.java:205)
    at net.sf.jasperreports.engine.fill.JRVerticalFiller.fillReport(JRVertic
    alFiller.java:119)
    at net.sf.jasperreports.engine.fill.JRBaseFiller.fill(JRBaseFiller.java:
    613)
    at net.sf.jasperreports.engine.fill.JRBaseFiller.fill(JRBaseFiller.java:
    483)
    at net.sf.jasperreports.engine.fill.JRFiller.fillReport(JRFiller.java:77
    at net.sf.jasperreports.engine.JasperFillManager.fillReport(JasperFillMa
    nager.java:248)
    at org.apache.jsp.JSP.UserGuide_jsp._jspService(org.apache.jsp.JSP.UserG
    uide_jsp:74)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:99)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:802)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper
    .java:325)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:2
    95)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:245)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:802)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(Appl
    icationFilterChain.java:252)
    at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationF
    ilterChain.java:173)
    at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperV
    alve.java:214)
    at org.apache.catalina.core.StandardContextValve.invoke(StandardContextV
    alve.java:178)
    at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.j
    ava:126)
    at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.j
    ava:105)
    at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineVal
    ve.java:107)
    at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.jav
    a:148)
    at org.apache.jk.server.JkCoyoteHandler.invoke(JkCoyoteHandler.java:306)
    at org.apache.jk.common.HandlerRequest.invoke(HandlerRequest.java:385)
    at org.apache.jk.common.ChannelSocket.invoke(ChannelSocket.java:745)
    at org.apache.jk.common.ChannelSocket.processConnection(ChannelSocket.ja
    va:675)
    at org.apache.jk.common.SocketConnection.runIt(ChannelSocket.java:868)
    at org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadP
    ool.java:684)
    at java.lang.Thread.run(Unknown Source)
    Caused by: java.io.InvalidClassException: net.sf.jasperreports.engine.base.JRBas
    eReport; local class incompatible: stream classdesc serialVersionUID = 604, loca
    l class serialVersionUID = 606
    at java.io.ObjectStreamClass.initNonProxy(Unknown Source)
    at java.io.ObjectInputStream.readNonProxyDesc(Unknown Source)
    at java.io.ObjectInputStream.readClassDesc(Unknown Source)
    at java.io.ObjectInputStream.readNonProxyDesc(Unknown Source)
    at java.io.ObjectInputStream.readClassDesc(Unknown Source)
    at java.io.ObjectInputStream.readOrdinaryObject(Unknown Source)
    at java.io.ObjectInputStream.readObject0(Unknown Source)
    at java.io.ObjectInputStream.readObject(Unknown Source)
    at net.sf.jasperreports.engine.util.JRLoader.loadObject(JRLoader.java:86
    ... 33 more
    Anyone pls help. It's bit urgent. Thanks.

    I was using iReport v0.5.0 and it uses jasperreports-0.6.7.jar (v0.6.7) of
    JasperReports. I compiled and i deployed my application in BEA weblogic server. I got the error listed below. Only after i saw your
    response explaining that iReport was the issue, i checked the iReport lib directory and found this version of jasperreport jar.
    iReport creates a java source file which is used to a jasper file.
    iReport will link in the v0.6.7 version of jasperReports. When you
    deploy your web application it will recognize this version through the compiled jasper file and give you the InvalidClassException, even
    though you only have one jasperReport jar deployed with your war file.
    The way i fixed this problem was to create my web application with the
    jasperreport jar comes with iReport.
    Thanks for mentioning iReport.
    Christopher
    Error:
    Caused by: java.io.InvalidClassException: net.sf.jasperreports.engine.base.JRBas
    eReport; local class incompatible: stream classdesc serialVersionUID = 607, local class serialVersionUID = 10002
    at java.io.ObjectStreamClass.initNonProxy(ObjectStreamClass.java:463)
    at java.io.ObjectInputStream.readNonProxyDesc(ObjectInputStream.java:1521)
    at java.io.ObjectInputStream.readClassDesc(ObjectInputStream.java:1435)
    at java.io.ObjectInputStream.readNonProxyDesc(ObjectInputStream.java:1521)
    ...

Maybe you are looking for