SG-300 28P switches problem with VLAN Data and Voice, working all the time as Voice VLAN
Hi Everyone,
Thank you very much for your help in advance. I’m pulling my hair to fix the problem.
I just got the new SG-300 28P switches. My Bios ordered for me. I did not know how it runs until now... not an IOS based. I really do not know how to configure it.
I have 2 VLAN are Data and Voice.
- Data VLAN ID is 2 IP 192.168.2.X/255.255.255.0
- Voice VLAN ID is 200 IP 192.168.22.X/255.255.255.0
- I created two vlans, in switch, Data and Voice.
- On the port number 28, it is trunk by default, so I add Data vlan ID 2 tagged.
- On the port number 26, it is trunk by default, so I add Voice vlan ID 200 tagged.
- On the port number 27, I add Data vlan ID 2 tagged for Data vlan out.
- Port settings No.1
I set it up as Trunk with Data vlan 2 untagged, and 200 Tagged (voice vlan). I plugged in a phone with a pc attached. But the PC will get to the vlan 200 to get the DHCP address, but no from vlan 2. The Phone works with correct vlan ip.
- Port settings No.2
Trunk with vlan 1UP, 2T, and 200T. The phone is even worse. Would never pick up any IP from DHCP.
- Port settings No.3
Access with 200U...of course the phone will work... and the PC could not get to its own vlan. Instead, the PC got an ip from the voice vlan. Not from VLAN 2.
I have Linksys phone I’m not sure if this help.
For more information I setup in switch,
- enable voice vlan
- set the port on auto voice vlan
- enable LLDP-MED globally
- create a network policy to assign VLAN 200
- assign this network policy to the port the phone is connected to.
I hope this information help to help me to setup Data and Voice vlans, to plug the phone to work with vlan Voice 200 (IP rang 192.168.22.X), from phone to Pc and pc work as Data vlan 2 (IP rang 192.168.2.X).
I just got done setting up voice VLANs on an SF 300-24P and verified working. This was working with Cisco 7900 series phones connected to a Cisco UC setup.
Here's my sample config.
Note that I edited this by hand before posting, so doing a flat out tftp restore probably won't work. However, this should give you a clue. Also, don't take this as 100% accurate or correct. I've only been working with these things for about a week, though I've worked with the older Linksys SRW switches for a couple of years. I'm a CCNP/CCDP.
VLAN 199 is my management VLAN and is the native VLAN on 802.1q trunks.
VLAN 149 is the data/computer VLAN here.
VLAN 111 is the voice/phone VLAN here.
VLAN 107 does nothing.
interface range ethernet e(1-24)
port storm-control broadcast enable
exit
interface ethernet e1
port storm-control include-multicast
exit
interface ethernet e2
port storm-control include-multicast
exit
interface ethernet e3
port storm-control include-multicast
exit
interface ethernet e4
port storm-control include-multicast
exit
interface ethernet e5
port storm-control include-multicast
exit
interface ethernet e6
port storm-control include-multicast
exit
interface ethernet e7
port storm-control include-multicast
exit
interface ethernet e8
port storm-control include-multicast
exit
interface ethernet e9
port storm-control include-multicast
exit
interface ethernet e10
port storm-control include-multicast
exit
interface ethernet e11
port storm-control include-multicast
exit
interface ethernet e12
port storm-control include-multicast
exit
interface ethernet e13
port storm-control include-multicast
exit
interface ethernet e14
port storm-control include-multicast
exit
interface ethernet e15
port storm-control include-multicast
exit
interface ethernet e16
port storm-control include-multicast
exit
interface ethernet e17
port storm-control include-multicast
exit
interface ethernet e18
port storm-control include-multicast
exit
interface ethernet e19
port storm-control include-multicast
exit
interface ethernet e20
port storm-control include-multicast
exit
interface ethernet e21
port storm-control include-multicast
exit
interface ethernet e22
port storm-control include-multicast
exit
interface ethernet e23
port storm-control include-multicast
exit
interface ethernet e24
port storm-control include-multicast
exit
interface range ethernet g(1-4)
description "Uplink trunk"
exit
interface range ethernet g(1-4)
switchport default-vlan tagged
exit
interface range ethernet e(21-24)
switchport mode access
exit
vlan database
vlan 107,111,149,199
exit
interface range ethernet g(1-4)
switchport trunk allowed vlan add 107
exit
interface range ethernet e(21-24)
switchport access vlan 111
exit
interface range ethernet g(1-4)
switchport trunk allowed vlan add 111
exit
interface range ethernet e(1-20)
switchport trunk native vlan 149
exit
interface range ethernet g(1-4)
switchport trunk allowed vlan add 149
exit
interface range ethernet g(1-4)
switchport trunk native vlan 199
exit
voice vlan aging-timeout 5
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
voice vlan oui-table add 108ccf MyCiscoIPPhones1
voice vlan oui-table add 40f4ec MyCiscoIPPhones2
voice vlan oui-table add 8cb64f MyCiscoIPPhones3
voice vlan id 111
voice vlan cos 6 remark
interface ethernet e1
voice vlan enable
exit
interface ethernet e1
voice vlan cos mode all
exit
interface ethernet e2
voice vlan enable
exit
interface ethernet e2
voice vlan cos mode all
exit
interface ethernet e3
voice vlan enable
exit
interface ethernet e3
voice vlan cos mode all
exit
interface ethernet e4
voice vlan enable
exit
interface ethernet e4
voice vlan cos mode all
exit
interface ethernet e5
voice vlan enable
exit
interface ethernet e5
voice vlan cos mode all
exit
interface ethernet e6
voice vlan enable
exit
interface ethernet e6
voice vlan cos mode all
exit
interface ethernet e7
voice vlan enable
exit
interface ethernet e7
voice vlan cos mode all
exit
interface ethernet e8
voice vlan enable
exit
interface ethernet e8
voice vlan cos mode all
exit
interface ethernet e9
voice vlan enable
exit
interface ethernet e9
voice vlan cos mode all
exit
interface ethernet e10
voice vlan enable
exit
interface ethernet e10
voice vlan cos mode all
exit
interface ethernet e11
voice vlan enable
exit
interface ethernet e11
voice vlan cos mode all
exit
interface ethernet e12
voice vlan enable
exit
interface ethernet e12
voice vlan cos mode all
exit
interface ethernet e13
voice vlan enable
exit
interface ethernet e13
voice vlan cos mode all
exit
interface ethernet e14
voice vlan enable
exit
interface ethernet e14
voice vlan cos mode all
exit
interface ethernet e15
voice vlan enable
exit
interface ethernet e15
voice vlan cos mode all
exit
interface ethernet e16
voice vlan enable
exit
interface ethernet e16
voice vlan cos mode all
exit
interface ethernet e17
voice vlan enable
exit
interface ethernet e17
voice vlan cos mode all
exit
interface ethernet e18
voice vlan enable
exit
interface ethernet e18
voice vlan cos mode all
exit
interface ethernet e19
voice vlan enable
exit
interface ethernet e19
voice vlan cos mode all
exit
interface ethernet e20
voice vlan enable
exit
interface ethernet e20
voice vlan cos mode all
exit
interface ethernet e1
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e2
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e3
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e4
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e5
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e6
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e7
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e8
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e9
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e10
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e11
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e12
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e13
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e14
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e15
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e16
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e17
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e18
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e19
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e20
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e21
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e22
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e23
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e24
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet g1
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet g2
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet g3
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet g4
lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
exit
interface ethernet e1
lldp med notifications topology-change enable
exit
interface ethernet e2
lldp med notifications topology-change enable
exit
interface ethernet e3
lldp med notifications topology-change enable
exit
interface ethernet e4
lldp med notifications topology-change enable
exit
interface ethernet e5
lldp med notifications topology-change enable
exit
interface ethernet e6
lldp med notifications topology-change enable
exit
interface ethernet e7
lldp med notifications topology-change enable
exit
interface ethernet e8
lldp med notifications topology-change enable
exit
interface ethernet e9
lldp med notifications topology-change enable
exit
interface ethernet e10
lldp med notifications topology-change enable
exit
interface ethernet e11
lldp med notifications topology-change enable
exit
interface ethernet e12
lldp med notifications topology-change enable
exit
interface ethernet e13
lldp med notifications topology-change enable
exit
interface ethernet e14
lldp med notifications topology-change enable
exit
interface ethernet e15
lldp med notifications topology-change enable
exit
interface ethernet e16
lldp med notifications topology-change enable
exit
interface ethernet e17
lldp med notifications topology-change enable
exit
interface ethernet e18
lldp med notifications topology-change enable
exit
interface ethernet e19
lldp med notifications topology-change enable
exit
interface ethernet e20
lldp med notifications topology-change enable
exit
interface ethernet e21
lldp med notifications topology-change enable
exit
interface ethernet e22
lldp med notifications topology-change enable
exit
interface ethernet e1
lldp med enable network-policy poe-pse
exit
interface ethernet e2
lldp med enable network-policy poe-pse
exit
interface ethernet e3
lldp med enable network-policy poe-pse
exit
interface ethernet e4
lldp med enable network-policy poe-pse
exit
interface ethernet e5
lldp med enable network-policy poe-pse
exit
interface ethernet e6
lldp med enable network-policy poe-pse
exit
interface ethernet e7
lldp med enable network-policy poe-pse
exit
interface ethernet e8
lldp med enable network-policy poe-pse
exit
interface ethernet e9
lldp med enable network-policy poe-pse
exit
interface ethernet e10
lldp med enable network-policy poe-pse
exit
interface ethernet e11
lldp med enable network-policy poe-pse
exit
interface ethernet e12
lldp med enable network-policy poe-pse
exit
interface ethernet e13
lldp med enable network-policy poe-pse
exit
interface ethernet e14
lldp med enable network-policy poe-pse
exit
interface ethernet e15
lldp med enable network-policy poe-pse
exit
interface ethernet e16
lldp med enable network-policy poe-pse
exit
interface ethernet e17
lldp med enable network-policy poe-pse
exit
interface ethernet e18
lldp med enable network-policy poe-pse
exit
interface ethernet e19
lldp med enable network-policy poe-pse
exit
interface ethernet e20
lldp med enable network-policy poe-pse
exit
interface ethernet e21
lldp med enable network-policy poe-pse
exit
interface ethernet e22
lldp med enable network-policy poe-pse
exit
lldp med network-policy 1 voice vlan 111 vlan-type tagged
interface range ethernet e(1-22)
lldp med network-policy add 1
exit
interface vlan 199
ip address 199.16.30.77 255.255.255.0
exit
ip default-gateway 199.16.30.3
interface vlan 1
no ip address dhcp
exit
no bonjour enable
bonjour service enable csco-sb
bonjour service enable http
bonjour service enable https
bonjour service enable ssh
bonjour service enable telnet
hostname psw1
line console
exec-timeout 30
exit
line ssh
exec-timeout 30
exit
line telnet
exec-timeout 30
exit
management access-list Management1
permit ip-source 10.22.5.5 mask 255.255.255.0
exit
logging 199.16.31.33 severity debugging description mysysloghost
aaa authentication enable Console local
aaa authentication enable SSH tacacs local
aaa authentication enable Telnet local
ip http authentication tacacs local
ip https authentication tacacs local
aaa authentication login Console local
aaa authentication login SSH tacacs local
aaa authentication login Telnet local
line telnet
login authentication Telnet
enable authentication Telnet
password admin
exit
line ssh
login authentication SSH
enable authentication SSH
password admin
exit
line console
login authentication Console
enable authentication Console
password admin
exit
username admin password admin level 15
power inline usage-threshold 90
power inline traps enable
ip ssh server
snmp-server location in-the-closet
snmp-server contact [email protected]
ip http exec-timeout 30
ip https server
ip https exec-timeout 30
tacacs-server host 1.2.3.4 key spaceballz timeout 3 priority 10
clock timezone -7
clock source sntp
sntp unicast client enable
sntp unicast client poll
sntp server 199.16.30.1
sntp server 199.16.30.2
ip domain-name mydomain.com
ip name-server 199.16.5.12 199.16.5.13
ip telnet server
Similar Messages
-
Serious problem with xorg - keyboard and mouse locks all the time.
In the last week I've notices serious problems with xorg.
After some event, I am not sure which one, keyboard stops responding.
Mouse cursor works, but I can't click on anything.
I can't switch to text console.
But I can kill xorg with CTRL+ALT+BACKSPACE.
Have you noticed something similiar?
I use xfce4, [testing] repository.Jacek Poplawski wrote:
In the last week I've notices serious problems with xorg.
After some event, I am not sure which one, keyboard stops responding.
Mouse cursor works, but I can't click on anything.
I can't switch to text console.
But I can kill xorg with CTRL+ALT+BACKSPACE.
Have you noticed something similiar?
I use xfce4, [testing] repository.
I had that a few days ago, couldn't reproduce it. I was also running xfce4. I havn't had it today and im running xfdesktop+xfce-mcs-manager+pekwm+xfce4-panel... so it may have been xfwm4.
James -
a few months ago I bought an imac 27 inch late 2013 .. §16GB - and flash memory) - 3,3 Ghz Intel Core 15
ever since I have continuously problems with my external HDD that disconnect all the time and cause problems in other software (Lightroom, Adobe PS CS6) ... it is not a HDD problem, because it occurs with my 3TB WD HDD (Time Machine), my 1TB WD and 1TB IOMEGA
any one have a solution? anyone dealt with this problem in the apple care program?You are still under warranty and/or have AppleCare. Call them. Let them deal w/it.
-
Please help. At work we have netgear and tplink. Since I updated my mini iPad and iPhone 4S with ios 7wifi drops all the time. What is the problem?
Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased. http://support.apple.com/kb/ht1430
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are drooping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
iPad: Issues connecting to Wi-Fi networks
http://support.apple.com/kb/ts3304
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h Mt
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
10 Ways to Boost Your Wireless Signal
http://www.pcmag.com/article2/0,2817,2372811,00.asp
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Ssrs 2008 r2 date parameter not working all the time
In an SSRS 2008 r2 report, I am not getting some records selected when I run the report in the ssrs 2008 r2 report.
However when I run the sql in ssis manager, the records are selected. Thus I am trying to determine why some of the records are not selected whe running the ssrs report.
In the table called 'transactionfile', the fields that I am trying to determine where there is a problem is the following:
SchoolNumber (varchar(50),null), and
TransactionPaymentDate (varchar(50),null).
Examples of data are SchoolNumber = '121' and TransactionPaymentDate = '04162014'
In the SSRS report, the parameter value for @SchoolNumber is text and the parameter value for @EndDate and @StartDate is date/time.
The following is the query I am having a problem with:
SELECT s.SchoolNumber,
CONVERT(smalldatetime,substring(TransactionPaymentDate,5,4) + '-' + substring (TransactionPaymentDate,1,2)+ '-' +
substring(TransactionPaymentDate,3,2)) as TransactionPaymentDate
from [eF].[dbo].[transactionfile] f
INNER JOIN
[eF].[dbo].schools] s
on rtrim(ltrim(s.SchoolNumber)) =rtrim(ltrim(f.SchoolNumber))
where rtrim(ltrim(s.SchoolNumber)) = rtrim(ltrim(@SchoolNumber))
AND
Cast(Right(TransactionPaymentDate,4)+Left(TransactionPaymentDate,4) as Date)
>= @StartDate
AND
Cast(Right(TransactionPaymentDate,4)+Left(TransactionPaymentDate,4) as Date) <= @EndDate
Thus could you suggerst what could be wrong when selecting some records by date?First check whether transaction payment date has 8 digit or not. In yes then try the below query,
SELECT s.SchoolNumber,
CONVERT(smalldatetime,substring(TransactionPaymentDate,5,4) + '-' + substring(TransactionPaymentDate,1,2)+ '-' +
substring(TransactionPaymentDate,3,2)) as TransactionPaymentDate
from [eF].[dbo].[transactionfile] f
INNER JOIN [eF].[dbo].schools] s
on rtrim(ltrim(s.SchoolNumber)) =rtrim(ltrim(f.SchoolNumber))
where rtrim(ltrim(s.SchoolNumber)) = rtrim(ltrim(@SchoolNumber))
AND
cast(substring(TransactionPaymentDate,5,4) + '/' +
substring(TransactionPaymentDate,1,2)+ '/' +
substring(TransactionPaymentDate,3,2) as date) between @StartDate AND @EndDate
Regards, RSingh -
I have iphone 4s and i did by mistake a restore with different id so i lost all my data and i got all the other id data , contacts .....etc , please how can i fix that mistake
How to Restore from a backup: http://support.apple.com/kb/ht1766
-
Having problems with ipad mini and Siri. Works sporadically, will work once and then the second time not. Worked all the time with the original Mailbox app. Then started doing the same thing when I installed the new update so wondering if it is software?
Hi,
I have the check box on a second Partition but not on the Time Machine one
I forget what I did now to get this called "Recovery HD"
For the rest try https://discussions.apple.com/docs/DOC-4055 User Tip that links to Pondini's work on Time Machine.
10:17 pm Friday; May 2, 2014
iMac 2.5Ghz i5 2011 (Mavericks 10.9)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
Couple of iPhones and an iPad -
hi im having problems with my internet and email Ive reset the network even with my WiFi on Ive also turned off and on airplane mode help please thank you
hi Ive reset my network toggled the airplane on and off and turned off my carrier off then turned my phone off and turned my carrier back on but still problem persists
-
Macbook battery life, is there a problem If I keep it plugged almost all the time?
Hello.
New Mac user here, so I was wondering if there's a problem if I keep my MBP plugged all the time.
Most of the time I'm on my room using my MBP fully charged and I don't disconnect it.
Is there a problem with my batter life if I do that?
Or it's recommended to unplug and use it till the battery run off and then charge it again?
Because I work a lot on my MBP and that way in a simple day I could charge it and run uff the energy of the battery 2 to 3 times at day.
What's better for the life of my battery?
And if you could give me some advices to maintenance my battery and Macbook pro (also programs) I would appreciate it.
I own a Macbook Pro 13-inch, Mid 2012
2.9 GHz Intel Core i7
8 GB 1600 MHz DDR3
Intel HD Graphics 4000 1024 MB
With OS X 10.9
ThanksTamarizz wrote:
New Mac user here, so I was wondering if there's a problem if I keep my MBP plugged all the time.
No. I do that most of the time. Perhaps monthly I discharge it to the 40% level to keep the battery happy. Do not discharge the battery completely. If you are forced to use only battery power and you see the battery is low warning terminate your session or plug into AC if you can.
Here are Apple articles with official battery usage guidelines:
http://www.apple.com/support/macbookpro/batteries_power/
Ciao. -
Has anybody experienced the iPhone off switch not working all the time.
I have an iPhone 5, it's about 16 months old and it has experienced an annoying issue. The off button does not work all the time, sometimes I have to press it multiple times and other times it just works. The worst case is when it does not work at all, very frustrating. I didn't expect this type of issue for a phone that is not even a year and a half old.
I did some searching on the internet and there are 2 schools of thought, the first is that this is a hardware fault and Apple know about it but won't admit it because it would cost them too much to repair/replace phones with the issue. The second school of thought is that it is a software issue and a backup/reset/restore will fix it; I tried doing this but it did not resolve the issue.
Further digging seemed to suggest that it was really a hardware fault and the only option was to get a refurb from Apple for a ton of money, not cool.
Anyway, if anyone has any more information that could help me resolve this issue I would greatly appreciate it.
//*eggbox23@diesel vdub, thanks for your suggestion, I setup an appointment with the Genius Bar and found out in about 5 minutes that everything I have read up on so far is true.
Firstly the technician admitted that there is a sporadic fault on the iPhone 4s and iPhone 5 switches, something to do with the design of the switch that included a rubber element that rolls up (whatever that means) and causes the switch to fail. He then indicated that the iPhone 5s does not have the issue because the switch has been completely redesigned.
Since I was stupid enough to not take out the extended warranty the only options he gave me were to purchase a new phone or to get a refurb for $269, not cool. Why would anyone think that a phone would not work correctly for 2 whole years when the phone only cost about $600!
Since I have about 7-8 months left on my phone contract I am not prepared to pay for either option. I find it amazing that a phone can develop this type of issue in such a short time and then expect the customer to pay for their failures. Apple supposedly sells a very high quality product for a very high price, looks like they have taken a step back from this philosophy.
I am disappointed in the options that he gave me (I don't blame the technician) but I suppose I expected more from Apple in terms of quality and service.
//*eggbox23 -
i formated my macbook pro with windows 7 and i lost all the drivers, does anyone know how to recover the drivers?
How did you get them to install the first time and where did you get them?
Read the Installation Guide, Boot Camp 4.0 FAQ and the Windows 7 FAQ.
Here's the Boot Camp Manual. -
i did a restore and this is all the time coming up but i bouth this from someone and i cant sign in with my id :-(
i forgot my apple id and now when i reset my phone .... in setup process its askin the apple id but i forgot it what to do now
-
Whenever I try to sync my phone with my computer it won't automatically sync my new music from my computer to my phone. When i select it to sync it says that it is going to delete all the music off my phone because its already with another device (or something along those lines) but I use my itunes from my computer to my phone. Does anyone know how I can fix this so it will sync. Will all the songs on my phone be on my computer so it won't matter if it deletes them off of my phone?
In the course of your troubleshooting to date, have you worked through the following document?
iOS: Device detected but not identified properly on iTunes for Windows -
IPad Retina Problem: Wireless Internet Connection Stops Working All The Time
the wireless would all the sudden stop working. What happen is, I'd be going from one page to another and then BOOM. No more loading, the little circular "loading" icon never ending.
Also happens with iTunes trailers app, in general all the wifi.
What i've already tried:
Performing a full ipad restoration (as new restoration). I dont have issues with my ipod touch 5 or my galaxy sIII or my pc's, so i assume the ipad retina is faulty?Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Problem with Java Dates and UPDATE for SQL2000
I am having problems with the date formats for Java. I am trying to put the current date time into a SQL table, here it the code I am using:
var Today = new Date()
var conn = Server.CreateObject( "ADODB.Connection" )
conn.Open( "Provider=SQLOLEDB;Server=(local);Database=BillTracking;UID=sa;PWD=;")
var sql = "UPDATE BillAssignments SET DatePosted = " + Today + " WHERE AssignmentID = '" + Request.QueryString("AssignmentID") + "'"
var rs = conn.execute(sql)
I keep getting different errors and I have been unable to find a solution yet. I know that I need to change the date format from the Java standard to the one that SQL likes.
Help....
Norm...Please tell us where the Java part of this comes in. I see that you are using JavaScript to load up data via an ADO connection (presumably on an IIS platform) - but I do not see where you are using Java
Lee
Maybe you are looking for
-
Can i use hdd + SSD in my macbook pro 2011 ?
can i use hdd + SSD in my macbook pro 2011 ? cause i already had 750GB and now i am palnnin gto buy SSD to install my system on it and keep the 750Gb as a storge can i ?
-
New DNS error for Back to My Mac?
when i check Back to my Mac i am getting an error that says "Contact your internet service provider for a different DNS server address, enter it in Network Preferences and try again." does anyone know what this means and what is going on with this? w
-
Good Morning all - I am using Captivate 8. I have noticed that when I am working in the project design - sometimes the timeline "ruler" disappears. I can no logner adjust where I want to start listing to the video, I can drag or move the progress i
-
I need a picture from an event that I only have video of. Is there a way to get a jpeg/still shot exported from imovie clip? I'm a fairly new mac user.
-
How can a Macbook Pro desktop folder font color be changed in Yosemite?
Would like to change the white text color on the desktop folders. Cannot find anywhere to change folder font colors in Yosemite OS. Using a Macbook Pro.