Slow booting for Satellite Pro P P300

My P300 has a slow boot and takes forever to go past the windows page. Any help on that?

Hi
My notebook booted slowly because I had too many processes running in the OS background.
I disabled it in msconfig.
I think you should try this too.
Furthermore you should update or remove the TEMPRO tool.
Check this!

Similar Messages

  • Win XP Display driver for Satellite Pro P300 PSPCDE requested

    After a clean XP installation I cannot install a proper display driver (Radeon 5145).
    No driver is offered at Toshiba's website.
    Is there any idea what I could do?
    Please help - thank you!!

    Hi
    From my knowledge this graphic card was built in other Toshiba series too.
    Satellite L500 PSLS9E
    Satellite L505 PSLS9E
    Satellite L550 PSLWSE
    Satellite L555 PSLWSE
    Satellite L630 PSK04E
    Satellite L650 PSK1JE
    Satellite L650D PSK1SE
    Satellite Pro L500 PSLSAE
    Satellite Pro L550 PSLWTE
    So try the drivers released fort the series listed above.

  • Need info about max HDD size available for Satellite Pro M30-813

    Hello,
    The following question is mainly to be addressed to authorized Toshiba support personnel. What exactly is the limitation of a maximum size of an internal HDD that I could use with my Satellite Pro M30-813?
    Recently, I have bought and installed seagate 160 GB SATA drive, onto which I have successfully installed WXP Pro and have been running it for quite a while with no problems. Recently, I have been copying large amount of data from an external hard drive to my new internal disk, and as the files were being copied as I noticed having about 50 GB free space left, I had experienced windows "delayed write failed" and a massive partition failure with no possibility to recover data. The system would no longer boot and the whole MBR was damaged. As the result, I have lost all data on my new disk.
    Although, I realize that Toshiba is not responsible for additional hardware that I use with my laptop and that is not officially supported by Toshiba, I am certain that as an end user of a Toshiba product I have the right to know about a max HDD size limitation information for my notebook model. Therefore, I request Toshiba technical support representative to give me a straight official answer to my question.
    Thank you in advance,
    Andrejs
    (You may also contact me privately at my e-mail address)

    Hi Andrew
    > The following question is mainly to be addressed to authorized Toshiba support personnel
    I think you are in the wrong area if you are looking for an answer from an authorized Toshiba support.
    This is a Toshiba user-to-user forum! You will meet here Toshiba notebook owner and enthusiasts who share knowledge and tries solve problems but nobody from Tosh :(
    I could provide my experience with the M30 Satellite and the HDD upgrade possibilities.
    In my knowledge the Sat M30 supports a 40GB, 60GB and 80GB HDD for sure.
    In my opinion you could use the 100GB HDD but bigger HDDs will not run and functions correctly.
    So switch to a lower HDD size and enjoy the notebook!
    Ive goggled a little bit and found compatible HDD and the part numbers
    HITACHI GBC000Z810 -> 80GB
    HITACHI GBC00014810 -> 80GB
    TOSHIBA HDD2188B -> 80GB
    HITACHI G8C0000Z610 -> 60GB
    HITACHI G8BC00013610 -> 60GB
    TOSHIBA HDD2183 -> 60GB
    TOSHIBA HDD2184 -> 60GB
    I hope this could help you a little bit!
    Best regards

  • ACPI Compliant BIOS for Satellite Pro A30

    Hello, I have a Satellite Pro A30 which has 1GB RAM and P4 2.8GHZ CPU. I was wondering when toshiba would be supplying ACPI compliant BIOS upgrades for these machines? Because I would like to upgrade to Windows Vista, upon running the Vista Upgrade Advisor, my machine will run Windows Vista Business, but I just want to use Windows Vista Basic.
    So I began the upgrade from within Windows XP and once the machine re-booted to begin the Vista installation I was confronted with the Blue Screen, stating that my BIOS wasn't fully ACPI compatible.
    This seems like such a shame as the machine is upto running Vista, but Toshiba have not provided ACPI bios upgrades. My bios revision is 1.80.
    Any idea?

    Hi Keith,
    I have an A30 also, after Googling around I've found that the A30 is ACPI 1.0 compliant and Vista requires ACPI 2.0, there is little difference and there are workarounds published on the net but they seem too complicated for me. The websites I've read think it is unlikely Tosh will release an updated BIOS as they would rather users upgraded their computers.
    I've been to the BIOS (Phoenix) makers website and followed a link to BIOS agent. They informed me they haven't produced an upgraded BIOS yet but I should try again in 6 months.
    I hope this helps a little, if I find anything constructive out I'll post it.

  • Memory Upgrade for Satellite Pro L10

    Can i add 512MB to the 256MB memory already on my laptop? And also what is the name of the memory supported by Satellite Pro L10.
    Thanx
    Femi

    Hi Femi,
    Your L10 has two memory slots available and will support a maximum of 2Gb RAM (2 X 1Gb modules).
    Check out the following URL for details of compatible modules for your notebook :-
    http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=11979&ft=m&st=3
    HTH

  • What is Toshiba part number for Satellite Pro L20

    Morning
    Does anyone happen to know the Toshiba Part Number for the Satellite Pro L20? I seem to have mislaid mine.
    Thanks
    Si

    Hi
    I dont know which number you mean exactly but there are many different Satellite Pro L20 models which different numbers.
    All necessary details and serial numbers you will find on the label which was placed at the bottom of the unit. Please check this.
    If you need these details for part ordering or recovery cd you should contact the Toshiba service partner. There you can order all supported parts.

  • Where can I get new charger for Satellite Pro L500-1D4?

    Hi, I would like to get a new charger for Toshiba. My first charger got lost and the second charger that I bought from ebay 3 months ago for 10,- has stopped working. Where can I get a charger from? I googled and I found couple of wesbites e.g.
    http://www.electronicavenue.co.uk/toshiba-satellite-pro-l500-1d4-laptop-charger-6380-p.asp
    Chargers cost around 25-30 GBP. I don't want anymore problems with a charger. I am already behind schedule...
    Where can I get a good charger from or that is genuine. Any other suggestions are welcome
    Thank you in advance

    Laptop: Satellite Pro L500-1D4
    Sorry I have been away to provide feedback to both your suggestions so here goes:
    @Macius The part number is not PA3716E-1AC3 as you have stated, it is PA3714E-1AC3. Find underneath the link to correct part number and I would appreciate it if you you or anybody else could confirm this.
    http://uk.computers.toshiba-europe.com/innovation/jsp/SUPPORTSECTION/discontinuedProductPage.do?service=UK&tab=1&Model= 1076043&Serie=1076038&Family=2327&x=76&y=16&Type=2 319&ACTION=SHOW_ATTRIBUTES&BV_UseBVCookie=yes&PROD UCT_ID=1076043
    The specs are as following:
    1. output current: 3.42 A
    2. output voltage: 19 V
    3. output voltage: 65 W
    4. input voltage: 100~240V 50/60Hz (Universal)
    5. dimension (WxHxD) in mm: 108 x 46 x 29.5
    6. AC Cable type: three-prong type (Minimum 1.7m long, black-colored)
    @Paolo30 I can get 10 -20 GBP charhger with a full year warranty.
    The two variant chargers that are coming up are, which one shall I select?:
    >A
    ># 3-pin UK Power Cord
    ># 1 Year Warranty
    ># Input: AC 100V-240V
    ># Output: DC 19v/3.42A 65W
    ># Connector: 5.5*2.5mm
    >B
    >Input : AC, 100-240V, 50-60HZ
    >Output :DC, 19V, 4.74A, 90W
    >Connecter size : interior diameter: 2.
    >external diameter: 5.5 mm
    >.Outlet: 3-prong
    Thank you for your time.

  • Floppy Disk drives for Satellite Pro 4200 and 4300 series

    I have four Satellite Pro laptops - a 4340, a 4310, a 4270 and a 4280 and I'm having difficulty getting the 4310 and the 4270 to recognise a particular FDD. My understanding was that Mitsumi D353G FDDs were compatible with these 4200 and 4300 series laptops but I can't get the 4270 and the 4310 to "see" them. They will both however "see" an alternative FDD I have - a Pansonic JU-226A202FC but I only have one of them and two laptops needing a replacement FDD. I have tried a D353G that I know works (from my 4280) in both the 4310 and the 4270 but to no avail. I'm keeping an eye out for another Pansonic JU-226A202FC FDD on ebay but no luck so far. It's so frustrating as I'm sure a D353G FDD should work in the 4270 and 4310 and I have two spare ones which I wanted to use. I've looked in TSETUP.exe and can see no settings I can change to make these laptops see the D353G FDDs so any help or insight greatly appreciated. Does anyone out there have a 4270 or a 4310 successfully running a D353G FDD or, is this a quirk and these two particular models were only made to work with a Pansonic JU-226A202FC FDD not the D353G FDDs? Any clues?

    Hello
    Unfortunately I am not technician but I assume that there is obviously some problem with compatibility. It is possible that pin assignment is different and you can not use them. If you want to have a precise explanation you should contact technicians. I am pretty sure that they have motherboard schemes and can give you a proper explanation and advice how to handle with this problem.
    Good luck!

  • Need new motherboard for Satellite Pro C50-A-1E0

    My son's Satellite Pro C50-A-1E0 went completely t*ts up. I think it is a common fault and requires a bios reset or something. Anyway I'm thinking a new motherboard will do the trick.
    Any help as to which motherboard to get that is compatible and would this actually help?
    Thanks.

    Hi nessie
    It is not easy to find new motherboard and believe me it is pretty expensive so you can buy new notebook.
    What you can do is to contact nearest Toshiba service provider at first. Explain the situation and ask if they can help you with this. They are also able to obtain new motherboard for you.
    Addresses and phone numbers you can find on http://www.toshiba.eu/innovation/generic/ASP_SUPPORT/

  • How install the LAN driver for Satellite Pro A120

    Actually, my problem is that i didnt know how to install the lan driver on my Satellite Pro A120 to connect throug the net.
    The issue that theres no installation to do to complete the install.
    And theres other issue that i need the Ethernet Controller
    My laptop was vista OS installed, But i change it and put Windows XP instead
    Plz help me

    Thats very easy to install the LAN driver.
    On the Toshiba website you can search for it:
    http://eu.computers.toshiba-europe.com => Support & Downloads => Download drivers
    Select the right notebook. In your case its the Satellite Pro => Satellite Pro A Series => Satellite Pro A120.
    And then choose at operating system Windows XP and at Driver type LAN Driver.
    Click on search and you will get the right driver.
    Download and install it. How this works did Jimi said.

  • Re: Cannot find drivers for Satellite Pro A300-1HE (PSAGDE)

    Hello,
    I have a Toshiba Satellite Pro A300-1HE (PSAGDE-00800QFR) with the serial number 78621314Q, but i find it anywhere on the toshiba site.
    I'am looking for drivers for the graphic card ATI, it has an ATI Mobility Radeon HD3650.
    Where can-i find drivers for this machine ?
    Thanks by advance

    Hi
    Go to Toshiba EU driver page
    http://www.toshiba.eu/innovation/download_drivers_bios.jsp?service=EU
    _Choose:_
    Notebook
    Satellite Pro
    Satellite Pro A
    Satellite Pro A300
    PSAGDE
    Thats all.

  • LAN driver for Satellite Pro L20 Windows 2000

    I am looking for a LAN (ethernet) drive for my Satellite Pro L20, which has Windows 2000 on it.
    I have found one for the WiFi, but not for the Ethernet (cable/CAT) connection.

    Hi
    Well, you cant find any LAN drivers for Win2000 on the Toshiba page because this unit was delivered and tested only with Windows Xp OS.
    Nevertheless I found the information that this unit has a Realtek 8100CL LAN card.
    In this case I assume to visit the Realtek website. There you will find a compatible driver for this LAN card.
    http://www.realtek.com.tw/downloads/downloads1-3.aspx?keyword=8100
    Bye

  • Which Solid State Hard Disk for Satellite Pro L670?

    I have a Satellite Pro L670 which I want to configure for presentation purposes and have to re-load the operating system anyway.
    Rather than over-write the existing disk, I thought it would be better to get a second one to fit instead.
    Replacing the current (old-fashioned) spinning disk with a solid state one seems to me the best way to go.
    Has anyone else fitted a solid state hard disk to a Satellite Pro?
    For budget reasons I am planning to go for a 120GB capacity which will be enough.
    However I have yet to find out from Toshiba what they might recommend. Anyone else yet gone this route?

    Hi
    Theoretically any SATA SSD drive should be compatible because the notebook supports an SATA controller.
    But in some cases it could be possible that an SSD drive would not be handled properly. In such cases the SDD drive manufacturers provides different firmware updates
    So before purchasing an SSD drive check the support pages of SSD drive manufacturers for further details maybe an firmware update would be available

  • Where can I find Vista drivers for Satellite Pro L450D?

    Hi, can anyone offer any help please?
    My toshiba Satellite Pro (Model L450D) came with Win 7 preinstalled. Unfortunately due to virus, I had to format the HDD and reinstall an operating system, but only had a legal copy of Vista. Now Toshiba utilities keeps coming up with a message saying it is blocked at start-up because it is not compatible with this version of Windows (vista).
    All the options to download anything for this laptop model is in Win 7, of course. Where can I find everything I need to be compatible with Vista please?
    Thanks in advance.

    And you think best solution for you is to use Vista or what?
    The whole problem is that you didnt follow Toshiba advice and create recovery disc. Can you confirm this?
    Using this disc you can have factory settings and Win7 again.
    In my opinion Vista is not solution. At first Vista is not supported so if you cannot find Vista stuff on Toshiba download page you will not be able to find it anywhere. Best option for you is to order original Toshiba recovery disc for your machine. You will get Win7 recovery image and you can use it anytime you want.
    For order check please https://backupmedia.toshiba.eu/landing.aspx
    If you have more questions you are welcome.

  • Need Vista 64-bit drivers for Satellite Pro P100

    Hello,
    I have one question about Drivers for Vista 64bit version. I have a notebook Satellite Pro P100 and search in the drivers catalogue and find only a BIOS update for 64-bit systems.
    But where can I find the Hardware drivers for 64-bit versions?
    Regards
    Mischa

    The 4 GB RAM issue is a known issue at the toshiba helpdesk (yes I had it and called) it's due to a problem programming the BIOS to handle more then 3GB.
    As for your drivers I can tell you in advance you can find everything except SD Card driver and the microphone jack in plug support driver.
    I'm sorry I forgot where I found those but the rest is out there (you can also try installing 32-bit version for the most).
    Ow and the BIOS - update for 64 bit doesn't work for me so don't count on it to much lol

Maybe you are looking for

  • MID YEAR GO LIVE ERROR

    MID YEAR GO LIVE ERROR Its a mid year go live and we have only year to date (YTD only and not QTD and MTD) data for gross pay ,deductions & taxes.Right now we are uploading the YTD gross in /101, YTD Social Secutiry in /403, YTD medicare in /405 , YT

  • CIN: Converting a C String to a LabVIEW String

    Hi all, I have been developing CINs in Microsoft Visual C++ 6.0 for LabVIEW as project needs. However, I am having a problem with converting a C String to a LabVIEW String in CIN. I used two ways to try to make the conversion work that were LStrPrint

  • Annoying NullPointer Exception

    Hi, I am writing a very simple Java applet (1.3) game (a 2d platformer) for my compsci project, and I have come across an annoying error at runtime: I have a boolean flag called collision which stores if a collision has occurred. It calls a chsckColl

  • Adding a Watermark after 'Importing Video'

    Hey there, I was hoping to create a watermark that fades into my videos 20 or so seconds in, then fades out after another 10 seconds. Here's what I've done so far in Flash CS4: - Import Video - Pointed the "player" to an external URL for the video. -

  • ISU_S_PARTNER_CHANGE - update business partner contact

    Hi There, Im trying to update a business partner's contact details. Currently I'm using ISU_S_PARTNER_CHANGE but it is not updating the details with the one being entered. and its still displaying the same old detail anyone if this is the correct fun