SNMP traps for tracking objects

Hi ,
I have the track objects configured as "boolean or" on my router. I want to configure to send SNMP traps when the "track 202" is down.
I know we can configure SNMP traps for IP SLA. Can we configure for the track as well ?. Below is the track CONFIG.
track 200 rtr 200 reachability
delay down 12
track 201 rtr 201 reachability
delay down 12
track 202 list boolean or
object 200
object 201
Thanks

Hi Rolf,
Thanks for the information. It helped me.
I have configured the trigger event to use the track instead insted of the syslog. And it send the traps to the server.
sysUpTime.0 = 1805405563
snmpTrapOID.0 = cEventMgrMIB.0.2
ceemHistoryEventEntry.2.3 = 211
ceemHistoryEventEntry.3.3 = 0
ceemHistoryEventEntry.4.3 = 0
ceemHistoryEventEntry.5.3 = 0
ceemHistoryEventEntry.6.3 =
ceemHistoryEventEntry.7.3 = applet: TRACK_SNMP_TRAP
ceemHistoryEventEntry.9.3 = 0
ceemHistoryEventEntry.10.3 = 0
ceemHistoryEventEntry.11.3 = DOWN
Cheers!
Win

Similar Messages

Css 11506 snmp trap for defective modules

is it possible that the css is sending a trap or mail if a module like the ssl module change the status to bad or powered-off. Are there scripts available for module monitoring
andre

Try this
snmp trap-host x.x.x.x community
snmp trap-type enterprise
snmp trap-type enterprise chmgr-module-transition
Syed

Sending snmp traps for SVM

i've got my box sending general traps, but i've noticed Sun Volume Manager requires separate configuration for this using /etc/snmp/conf/mdlogd.acl. How can i now verify that i will get traps if my internal drives (mirrored using meta commands) have issues or fail? is there a meta or md command i can issue as a check?
thanks

Hi Rolf,
Thanks for the information. It helped me.
I have configured the trigger event to use the track instead insted of the syslog. And it send the traps to the server.
sysUpTime.0 = 1805405563
snmpTrapOID.0 = cEventMgrMIB.0.2
ceemHistoryEventEntry.2.3 = 211
ceemHistoryEventEntry.3.3 = 0
ceemHistoryEventEntry.4.3 = 0
ceemHistoryEventEntry.5.3 = 0
ceemHistoryEventEntry.6.3 =
ceemHistoryEventEntry.7.3 = applet: TRACK_SNMP_TRAP
ceemHistoryEventEntry.9.3 = 0
ceemHistoryEventEntry.10.3 = 0
ceemHistoryEventEntry.11.3 = DOWN
Cheers!
Win

SNMP trap for STP

Hi,
does command "snmp-server enable traps bridge newroot topologychange" work for all spanning tree modes (PVST, RPVST, MST)?
i.e. will it be sent when there is new root in MST, or if there is new root in one VLAN in PVST+?
Is there information in the trap which bridge ID is new root?
And regarding topology change, shall all bridges send "topologychange" TRAP to SNMP server, since TCN is usually spread to all switches in MST (or PVST) region?
Thanks,
A

While I haven't tested this personally, the code indicates this trap is applicable to PVST, RSTP, and MSTP. The trap will only be sent from switches that have an STP port state change (i.e. a port goes from forwarding to blocking for an instance of ST).

Phantom SNMP Traps

Hi,
I've got most of my devices spouting SNMP traps for various different things, and Ciscoworks forwards these traps on via email, as you do.
For most things it works great, however since we've created a script to pull on the configs off the devices (Simply don't trust Ciscoworks), we're always spammed with SNMP traps like the one below:
ALERT ID                = 000071P
TIME                    = Mon 10-Jan-2011 16:19:07 GMT
STATUS                  = Active
SEVERITY                = Critical
MANAGED OBJECT          = lrouter-loo-0.mwam.local
MANAGED OBJECT TYPE     = Switches and Hubs
EVENT DESCRIPTION       = router1-loo-0.mwam.local: Cisco Configuration Management Trap:InformAlarm; PORT-lon-cr1-loo-0.mwam.local/10113 [Gi1/0/13] [Trunk to router2-gig-1-0-24]:OperationallyDown;
CUSTOMER IDENTIFICATION = networks-info
I know one port is down, and that's expected, I just haven't cleared the alert and turned off the monitoring in DFM.
We're using:
snmp-server enable traps config-copy
snmp-server enable traps config
on all of our devices, but only 4 out of 80+ devices throw this trap out when their config is copied by the script.
I've googled extensively, but I haven't come across any real help.
Has anyone got any idea what the situation is with this? I'm getting bored of deleting a bunch of emails every time our script runs, and I don't want to create a rule for fear of filtering real alerts.
Any ideas would be appreciated
Cheers

This isn't a trap. This is a DFM alert, which consists of multiple atomic events. In this case, it looks like the alert consists of two events. The first is a CISCO-CONFIG-MAN-MIB trap (i.e. ciscoConfigManEvent). If you look at the associated event in the DFM Alerts and Acitivities Display, I'll bet it will indicate the configuration was copied (per your script). The other event indicates that port Gi1/0/13 is operationally down on this switch. The two events are unrelated, but apply to the same device.

No SNMP traps from sun x4150 ILOM server

Hi all,
I have set up the ILOM alerts with SNMP traps (v2c,public) according to the ILOM user guide and pressed the "send test alerts". Nothing shows up in the SNMP trap monitor (using MG-SOFT software). When I add another alert of IPMI pet type (same destination ip as of SNMP trap alert) I see events in the trap monitor. It looks like the ILOM does not generate SNMP traps but only IPMI traps.
In the ILOM user guide there is an explicit example of traps sent from the ILOM (in addition to the fact that the ILOM features include SNMP traps AS WELL as IPMI) so it seems this is possible...
my ILOM version is
SP Firmware Version 2.0.2.6
Does anyone have any idea of any step I have missed ?
Thanks in advance.
Lior

Once the Network Device (Linux server in this case) is discovered you will still need a rule that targets that class and accepts incoming SNMP Traps for that OID, or All OIDs if you prefer. I found 2 links that may be of help, the first is just a basic
overview of the SNMP listener in SCOM 2012 as it has changed from the OS Listener in 2007 to a dedicated one.
http://systemcentertech.com/2012/05/17/scom-2012-built-in-snmp-trap-listener/
The second link covers SNMP setup, but starting at Step 7 there is a great how-to on creating your own SNMP rule which will be needed to collect your traps.
http://scom-2012.blogspot.com/2012/07/setting-up-snmp-monitoring-in-scom-2012.html
www.Practice2Perfect.com

SNMP traps from EMC SRM to SCOM 2012 R2

Hi,
I'm trying to configure SCOM 2012 R2 as an SNMP trap listner. I've seen many articles on setting this up but all are based around SNMP traps from network devices which must first be discovered and identified in the network device list.
However in my scenario I am trying to monitor/listen for traps send by a Linux box hosting EMC SRM - this management software can be configured to send SNMP traps out so it is these that I need to try and listen for/capture.
So can anyone explain how I can configure SCOM 2012 R2 to do this. I have tried to just used the IP of the Linux box and discover it as a network device but it fails - in Network Devices Pending Mgmt it says No response Ping, even though I can
ping the box from the Server OK - so I am guessing you cant cheat scom in discovering the Linux box as a network device in ths way?
Can anyone offer any advice for setting this up. Just to add I've ensured the RunAs Community String (public) and SNMP version is correct on both side...
Cheers...

Once the Network Device (Linux server in this case) is discovered you will still need a rule that targets that class and accepts incoming SNMP Traps for that OID, or All OIDs if you prefer. I found 2 links that may be of help, the first is just a basic
overview of the SNMP listener in SCOM 2012 as it has changed from the OS Listener in 2007 to a dedicated one.
http://systemcentertech.com/2012/05/17/scom-2012-built-in-snmp-trap-listener/
The second link covers SNMP setup, but starting at Step 7 there is a great how-to on creating your own SNMP rule which will be needed to collect your traps.
http://scom-2012.blogspot.com/2012/07/setting-up-snmp-monitoring-in-scom-2012.html
www.Practice2Perfect.com

SNMP Query for Byspass Status (AIP5)

I'd like to monitor the state of Bypass mode for the ASA-SSC-AIP-5 and would like to know if I can check this with SNMP and if so, which OID.
I started messing with SNMP and the SSC5 a while back and started a thread about snmpwalk causing it to crash. After that, I never really picked the project back up.
I've been known to miss the obvious every now and then, but I was dissapointed to see that there wasn't an (obvious) way for the device to alert you when it automatically goes into bypass mode. This should be a feature request.

IPS provides SNMP traps for different interface conditions like link going down or up, traffic bypass started, etc. Below is one such example
Received SNMPv2c Trap: Community: "public"
From: 10.89.149.204 mib_2.1.3.0 = 38429472
snmpModules.1.1.4.1.0 = ciscoMgmt.138.2.0.1
ciscoMgmt.138.1.3.3.1.3 = 3                      <====    index can be mapped to index obtained from snmpwalk
ciscoMgmt.138.1.3.3.1.4 = 5                      <====    Traffic bypass started
ciscoMgmt.138.1.3.3.1.5 = 4
ciscoMgmt.138.1.3.3.1.6 = 38429472
All you need to do is enable sending traps from the sensor.
qssp-8085(config)# service notification
qssp-8085(config-not)# enable-set-get true
qssp-8085(config-not)# enable-notification true
qssp-8085(config-not)# read-only-community public
qssp-8085(config-not)# read-write-community private
qssp-8085(config-not)# trap-destinations x.x.x.x           <===== trap destination
qssp-8085(config-not-tra)# exit
qssp-8085(config-not)# exit
You can configure separate community name under trap-destination. If not provided then the read-write-community will be used to send with the trap.
Hope this helps
Madhu

Snmp alerts for CPU utilization

Hi,
I want to enable snmp alerts on l2 and l3 switches to monitor CPU utilization.
I have Opmanager which is acting as SNMP server.
I have switches L2 and L3 which are running IOS 12.0, 12.1, 12.2
Do all these IOS versions support SNMP alerts?
And also I want to know the commands to be configured on switches for this.
Regards
skrao

You can configure SNMP traps for CPU Thresholding Notification.
http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a0080455772.html
You should be ok with the versions you list but check exact IOS version supports it at http://www.cisco.com/go/fn
If you do not want to use traps then there are specific oids that can be polled for 1minute average (1.3.6.1.4.1.9.2.1.57) and also 5 minute average (1.3.6.1.4.1.9.2.1.58). I've used these in the past with no problems. These oids may have been superceeded so check for latest. You can always snmpwalk a device to check oids.
The cisco SNMP navigator is helpful when it comes to oids.
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en
If you haven't got any SNMP configured yet on the switch check out http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Network%20Management&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddb4e54
HTH
--Phil

Disable default snmp traps

Hello,
I am trying to disable the default snmp trap for x25. I tried to use the "no" form of the command (no snmp-server enable traps x25), but after typing:
no snmp-server enable traps ?
x25 is not even listed.
The other workaround was to specify exactly what type of traps I wanted to be sent to my snmp-server using the commands:
snmp-server host ip_address community flash tty snmp
(x25 was not included), but that didn't solve the problem.
Any assistance would be highly appreciated.
Regards,
Katerina

Hi,
I have tried it with solarwinds and works fine for me. Talking about the traps. But they are too many.
The OID is : 1.3.6.1.4.1.14179.1.1.2.4.1.22
snmp info for polling:
MIB Value Type: Raw Value
Format: None
SNMP Get Type: Get Table
Polling Type: node
On WLC go to Managemnet (top TAB)
Right hand select > SNMP > Traps Control.
In this menu select what traps to need to be logged.
These traps will be shows on the oid polled.

Snmp Traps using in SSIS

Hi All,
I want to use Snmp Traps for SSIS packages.If any error in Package,
I want to send notifications to main server.
How can we implement in SSIS.Can we implement in SSIS?
If anybody knows please tell me it is very urgent.
Thanks in Advance.

I've not used it
But you may try code like below within script task in SSIS
http://www.c-sharpcorner.com/forums/thread/59866/sending-snmp-traps.aspx
Please Mark This As Answer if it solved your issue
Please Mark This As Helpful if it helps to solve your issue
Visakh
My MSDN Page
My Personal Blog
My Facebook Page

LMS 3.2.1 integration with Clarity NMS for snmp trap forwarding

Our client have integrated Clarity NMS to Ciscoworks LMS 3.2.1. So far they are receiving raw alarms/snmp traps but it lacks information/inventory of the originating device. Kindly see sample raw alarms below:
2420: 2011-11-25 12:10:46 Received trap ==> Received SNMPv1 Trap
Community=ciscoworks
Enterprise=1.3.6.1.6.3.1.1.5
Generip trap type=2
Specific Trap Type=0
Trap From=10.220.10.1
Trap ID=1.3.6.1.6.3.1.1.5.2
Trap Time=-1436283373
1.3.6.1.2.1.2.2.1.1.83=83
1.3.6.1.2.1.2.2.1.2.83=GigabitEthernet1/40
1.3.6.1.2.1.2.2.1.3.83=6
1.3.6.1.4.1.9.2.2.1.1.20.83=Lost Carrier
EndTrap
10933: 2011-11-24 11:57:53 Received trap ==> Received SNMPv1 Trap
Community=ciscoworks
Enterprise=1.3.6.1.4.1.9.1.291
Generip trap type=2
Specific Trap Type=0
Trap From=10.220.10.1
Trap ID=1.3.6.1.4.1.9.1.291.2
Trap Time=1628056965
1.3.6.1.2.1.2.2.1.1.8=8
1.3.6.1.2.1.2.2.1.2.8=E1 0/0/0
1.3.6.1.2.1.2.2.1.3.8=18
EndTrap
As you can see, those raw alarms doesn’t contain any information about the originating equipment or the physical card, port related information where those alarms were generated. Instead those alarms received are just NMS level alarms.
How do we resolve this so that the inventory of the equipment would be part of the trap to be received by Clarity from Ciscoworks.

Hi,
Is the issue you have the source IP address of the forwarded trap? Per RFC it is the IP of the actual device sending the trap. The originating IP should be contained within the packet. I have included some additional information you may find helpful.
Q. What is the difference between SNMP Raw Trap Forwarding and SNMP Trap alert/event Trap Forwarding? Does DFM support both?
A. You can configure raw trap forwarding at DFM > Other configuration > SNMP Trap forwarding, and processed event/alert trap forwarding at DFM > Notification Services > SNMP Trap Forwarding. Processed trap is "when DFM receives certain SNMP traps, it analyzes the data found in fields (Enterprise/Generic trap identifier/Specific Trap identifier/variable−bindings) of each SNMP trap message, and changes the property value of the object property (if required)". Raw trap is the trap that the device forwards to DFM and DFM has yet to process it. For more information, refer to the DFM User Guide. Yes, DFM supports both ways of trap forwarding.
http://www.cisco.com/en/US/products/sw/cscowork/ps2421/products_qanda_item09186a0080a9b35b.shtml
DFM will only forward SNMP traps from devices in the DFM inventory. It will not change the trap format—it will forward the raw trap in the format in which the trap was received from the device. However, you must enable SNMP on your devices and you must do one of the following:
Configure SNMP to send traps directly to DFM
Integrate SNMP trap receiving with an NMS or a trap daemon
The versions of SNMP traps supported by DFM are described in SNMP and ICMP Polling. For information on forwarding processed and pass-through traps, see Processed and Pass-Through Traps, and Unidentified Traps and Events.
Pass-through traps are traps that DFM receives from devices that are not in the DFM inventory, and DFM has not processed. Forwarding these traps is controlled using Configuration > Other Configurations > SNMP Trap Forwarding. These traps are shown in the Alerts and Activities display because of their relevance to fault monitoring. Pass-through traps are displayed as follows:
As one of the following events:
> InformAlarm
> MinorAlarm
> MajorAlarm
With the device type and the device name from which it was generated.
If DFM does not know which device generated the trap, it ignores the trap. Pass-through traps will be cleared after a default interval of 10 minutes to one hour
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_device_fault_manager/3.2/user/guide/dfm32ug_Book.html

Different Source Address for a SNMP trap paquet

We use a common platform to manage the CISCO routers for several customers. We are using to manage the devices w/ a loopback address as source of snmp paquet.
We use something like this ...
Router(config)#snmp-server host 172.25.1.1 ORATRAP
Router(config)#snmp-server trap-source loopback0
Router(config)#end
Now, there is some customers that request us to receipt the snmp-traps w/ an ip source of their own ip space (192.168.2.x/24).I cannot imagine how this can be achieve?... Please any idea?. Thks. Eduard.

Thks., for your help. This is important matter to us. We also working in the idea of snmp track collector close to our own NMC... but this may cost also money... . So, we are going to try another approach first..
Somewhat like this below....
snmp-server enable traps
snmp-server informs
snmp-server source-interface traps
snmp-server source-interface informs
snmp-server host traps version 1 community string publicCust
snmp-server host informs version 2 community string publicBT
For the get's every MNC sends to the declared IP, so We thing that will use the same IP in answer.
I will let you know. Eduard.

SNMP Trap Translation Wrong For Hebrew Language

SR 3-4956842281
sev 2
Cus ISRAEL CREDIT CARDS LTD
=====================
Customer is using OMS 10.2.0.5 on linux server.
They have created an user defined metric on DB cluster instance with alert message written in hebrew.
The OMS console showed the alert in hebrew as expected.
However when they send this alert with snmp trap notification to a second system (HP openview for windows) then the message appeared not cleared (with question marks). This second system get messages in hebrew from other systems without any problems.
+Does setting LANG variable at OMS level will impact this
+Any tracing which can help to find the cause of the issue

Closing as issue found at HP openview parameter settings

How to enable the "SNMP TRAP" Funcation in Prime Infrasructure 2.0 for receiveing the Third Party Device's SNMP TRAP

I already uploaded the third party device's MIB to PI2.0, but could not recive the third party device's SNMP TRAP properly .
what do I need check for the PI ? or what do I need to setup for the PI?
Thanks

Duplicate post of :
https://supportforums.cisco.com/discussion/12148626/how-enable-snmp-trap-funcation-prime-infrasructure-20-receiveing-third-party
-Thanks
Vinod

SNMP traps for tracking objects

Similar Messages

Maybe you are looking for