Split signal into XY components
Hi,
I am new to LabVIEW but have spend a huge amount of time (mainly going round in circles not getting anywhere) trying to get my VI design working. All very frustrating since I know what I want the VI to do but cannot figure out how to implement it in LabVIEW (despite hours of searching in this LabVIEW forum and in the help files).
I need to....
Take a signal from DAQ Assistant, when the signal is at a particular threshold (user configurable via Front Panel) log the data to Measurement File and stop logging when the signal reaches a higher threshold (I tried using the 'Trigger and Gate' VI in Express but it doesn't allow user configurable values for thresholds (only integers)).
Then I need to read back the Measurement File and split it into its XY parts to display on an XY Graph (and keep it displayed on the front panel for user observation).
Any help would be greatly appreciated but please explain in detail as I've already played with LabVIEW for hours and hours and haven't got anywhere.
Regards,
Hi bunnykins,
I think you can try using normal greater than /less than comparison functions and log the data using the Write to measurement file with append to file option enable.I have attached the screenshot of the block diagram.Please have a look. Thanks and regards, srikrishnaNF
Attachments:
first.png.zip 21 KB
Similar Messages
-
How to split signal into xy components
i am simulating a digital signal and viewing it on a graph, I would like to input x and receive the corresponding y coordinate.
I have a attched a screen shot.
If anyone can help, I'd really appreciate it! Thanks!!
Attachments:
singal and graph.pdf 10 KBLook into the Get Waveform Subset. If you set the duration to 1 sample (or dt if indexing by relative time), you should only get 1 element. Just use Array Index and you got your value.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
xy point graph_BD.png 63 KB -
Split string into its number and alphabetic​al components
I have a string constant "There are 100 pens and 200 pencils in the box".i want to split it into two parts one consisting of array of numbers i.e. 100 and 200,while the second part should display "There are pens and pencils in the box".
How should i proceed?That looks like homework.
What have you tried so far and where did you get stuck?
LabVIEW Champion . Do more with less code and in less time . -
How to adjust splitted lines into one line in Text file?
Hi Guys,
I have a text file with 3 fields(comma separated): GLCode (Number), Desc1 (Char), Desc2(Char) and need to load it into BW.
My Text file looks like:
1011.00,"Mejor PC Infrastructure","This line is ok."
1012.00,"Telephone Equipment $","This line ends in next line.
1)Need to change the equipment immediately.
2)Take immediate action"
1013.00,"V1 Computer Server Infrastructure # Equip","For purchases
of components that make up the company's network, such as servers, hubs, routers etc."
1014.00,"Flash Drive","Need to provide all IT Developer"
This is how file looks like. Now I need the followings:
1. Need to remove the space and need to adjust the splitted line into one. Say here
line/record 2 is splitted into 3 lines and need to adjust in 1 line.
2. In Line 5 (Record 3) data splitted into 2 lines and need to make 1 line.
3. Need to remove bad characters.
Could someone help me please how to proceed ?
Regards,Not quite correct by my testing. Try:
$i=0
Get-Content .\test.txt | ForEach {
If ($i%2){
("$Keep $($_)").Trim()
}Else{
$keep=$_
}$i++
Good catch!
Boe Prox
Blog |
Twitter
PoshWSUS |
PoshPAIG | PoshChat |
PoshEventUI
PowerShell Deep Dives Book -
How to convert a waveform signal into array of complex numbers
How to convert a waveform signal into array of complex numbers.
Hi Chaks,
try this:
(Get Waveform components, convert to complex DBL)
Message Edited by GerdW on 01-28-2008 09:23 AM
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome
Attachments:
ToCDB.png 1 KB -
Equivalent of Split Signals for digital waveform
Hi , I read multi digital waveforms in a loop and I would like to split the channels. For analog waveform I can simply use split signals control. How about digital waveform, is there any equivalent for digital channels?
You can use firstly "Digital to Boolean Array VI" to get a 2D boolean aray equivalent of Digital Waveform samples...!!
But remember at this step, the sampling rate information (dt) will be lost (after you've converted the digital waveform to 2d array of boolean)...
Now next, if I'm not wrong, here each column would represent different waveforms...!!
At last, you can use "Boolean Array to Digital VI" to convert 2d array of boolean back to digital waveform...!! You will require dt (sampling rate info) here at this step...!!
Additionaly to extract sampling rate info from the digital waveform, before you convert it to boolean array, you can use "Get Waveform Components (Digital Waveform) Function"
I am not allergic to Kudos, in fact I love Kudos.
Make your LabVIEW experience more CONVENIENT. -
Hi all,
I am new to ABAP Development. I need to upload a .DAT file (the file doesn#t have any proper structure-- Please find the .DAT file in the attachment). After uploading the DATA (.DAT) fiel I need to split in into different columns. Refering the attached .DAT fiel the fields in bracets like:
[Arbeitstag], [Pecunia], [Mita], [Kunde], [Auftrag] and [Position] are different fields that need to be arranged in columns in an internal table. this .DAT fiel which I want to upload and then SPLIT it into various fields will will treated as MASTER DATA table for further programming. The program that I had written is as below. Also please refer the attached .DAT table.
Please if any one could help me. i searched a lot in different forums but couldn't find me a solution. Also note that the attached fiel is in text (.txt) format here but in real situation the same fiel is in DATA (.DAT) format.
*& Report ZDEMO_ZEITERFASSUNG9
REPORT ZDEMO_ZEITERFASSUNG9.
Types: Begin of ttab,
Rec(1000) type c,
End of ttab.
DATA: itab type table of ttab.
DATA: wa_tab type ttab.
DATA: file_str type string.
Parameters: p_file type localfile.
At selection-screen on value-request for p_file.
CALL FUNCTION 'KD_GET_FILENAME_ON_F4'
EXPORTING
* PROGRAM_NAME = SYST-REPID
* DYNPRO_NUMBER = SYST-DYNNR
* FIELD_NAME = ' '
STATIC = 'X'
* MASK = ' '
CHANGING
file_name = p_file.
* EXCEPTIONS
* MASK_TOO_LONG = 1
* OTHERS = 2
Start-of-Selection.
file_str = P_file.
CALL FUNCTION 'GUI_UPLOAD'
EXPORTING
filename = '\\10.10.1.92\Volume_1\_projekte\Zeiterfassung-SAP\BUP_ZEIT.DAT' " This the file source address
FILETYPE = 'DAT'
HAS_FIELD_SEPARATOR = ';'
* HEADER_LENGTH = 0
* READ_BY_LINE = 'X'
* DAT_MODE = ' '
* CODEPAGE = ' '
* IGNORE_CERR = ABAP_TRUE
* REPLACEMENT = '#'
* CHECK_BOM = ' '
* VIRUS_SCAN_PROFILE =
* NO_AUTH_CHECK = ' '
* IMPORTING
* FILELENGTH =
* HEADER =
tables
data_tab = itab
EXCEPTIONS
FILE_OPEN_ERROR = 1
FILE_READ_ERROR = 2
NO_BATCH = 3
GUI_REFUSE_FILETRANSFER = 4
INVALID_TYPE = 5
NO_AUTHORITY = 6
UNKNOWN_ERROR = 7
BAD_DATA_FORMAT = 8
HEADER_NOT_ALLOWED = 9
SEPARATOR_NOT_ALLOWED = 10
HEADER_TOO_LONG = 11
UNKNOWN_DP_ERROR = 12
ACCESS_DENIED = 13
DP_OUT_OF_MEMORY = 14
DISK_FULL = 15
DP_TIMEOUT = 16
OTHERS = 17
IF sy-subrc <> 0.
* MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
* WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
LOOP at itab into wa_tab.
WRITE: / wa_tab.
ENDLOOP.
I will be grateful to all you experts for ur inputs
regards
Chandan SinghFor every Auftrag, there are multiple Position entries.
Rest of the blocks don't seems to have any relation.
So you can check this code to see how internal table lt_str is built whose first 3 fields have data contained in Auftrag, and next 3 fields have Position data. The structure is flat, assuming that every Position record is related to preceding Auftrag.
Try out this snippet.
DATA lt_data TYPE TABLE OF string.
DATA lv_data TYPE string.
CALL METHOD cl_gui_frontend_services=>gui_upload
EXPORTING
filename = 'C:\temp\test.txt'
CHANGING
data_tab = lt_data
EXCEPTIONS
OTHERS = 19.
CHECK sy-subrc EQ 0.
TYPES:
BEGIN OF ty_str,
a1 TYPE string,
a2 TYPE string,
a3 TYPE string,
p1 TYPE string,
p2 TYPE string,
p3 TYPE string,
END OF ty_str.
DATA: lt_str TYPE TABLE OF ty_str,
ls_str TYPE ty_str,
lv_block TYPE string,
lv_flag TYPE boolean.
LOOP AT lt_data INTO lv_data.
CASE lv_data.
WHEN '[Version]' OR '[StdSatz]' OR '[Arbeitstag]' OR '[Pecunia]'
OR '[Mita]' OR '[Kunde]' OR '[Auftrag]' OR '[Position]'.
lv_block = lv_data.
lv_flag = abap_false.
WHEN OTHERS.
lv_flag = abap_true.
ENDCASE.
CHECK lv_flag EQ abap_true.
CASE lv_block.
WHEN '[Auftrag]'.
SPLIT lv_data AT ';' INTO ls_str-a1 ls_str-a2 ls_str-a3.
WHEN '[Position]'.
SPLIT lv_data AT ';' INTO ls_str-p1 ls_str-p2 ls_str-p3.
APPEND ls_str TO lt_str.
ENDCASE.
ENDLOOP. -
Reading fixed length flatfile & splitting it into header and lineitem data
Hi Friends,
I am reading a fixed length flat file from application server into an Internal table.
But problem is, data in flat file is in the below format with fixed start and end positions.
1 - 78 - control header
1 - 581 - Invoice header data
1 - 411 - Invoice Line item data
1 - 45 - trailer record
There will be one control header and one trailer record per file and number of invoice headers and its line items can vary.
There is unique identifiers to identify as below.
Control header - starts with 'CHR'
Invoice Header starts with - '000'
Invoice Lineitem stats with - '001'
trailer record - starts with 'TRL'
So its like
CHR.......control data..(79)000.....header data...(660)001....lineitem1...(1481)001...lineitem2....multiples of 411 and 581 and ends with... TRL...trailer record..
(position)
I am first reading the data set and store in internal table with a field of 255char.
by looping on above ITAB i have to split it into Header records and line item records.
Did anyone face this kind of scenario before. If yes appreciate if you can throw some ideas on logic to split this data.
Any help in splitting up the data is highly appreciated.
Regards,
Simha
ITAB declaration
DATA: BEGIN OF ITAB OCCURS 0,
FIELD(255),
END OF ITAB,
lt_header type table of ZTHDR,
lt_lineitem type table of ZTLINITM.Hi,
i am sending sample code which resembles your requiremeant.
data: BEGIN OF it_input OCCURS 0, "used for store all the data in one line.
line type string ,
END OF it_input,
it_header type TABLE OF string WITH HEADER LINE,"use to store all header with corresponding items
it_item type TABLE OF string WITH HEADER LINE.."used to store all item data
CALL FUNCTION 'GUI_UPLOAD'
EXPORTING
filename = 'd:\test.txt'
FILETYPE = 'ASC'
HAS_FIELD_SEPARATOR = ' '
HEADER_LENGTH = 0
READ_BY_LINE = 'X'
DAT_MODE = ' '
CODEPAGE = ' '
IGNORE_CERR = ABAP_TRUE
REPLACEMENT = '#'
CHECK_BOM = ' '
VIRUS_SCAN_PROFILE =
NO_AUTH_CHECK = ' '
IMPORTING
FILELENGTH =
HEADER =
tables
data_tab = it_input
EXCEPTIONS
FILE_OPEN_ERROR = 1
FILE_READ_ERROR = 2
NO_BATCH = 3
GUI_REFUSE_FILETRANSFER = 4
INVALID_TYPE = 5
NO_AUTHORITY = 6
UNKNOWN_ERROR = 7
BAD_DATA_FORMAT = 8
HEADER_NOT_ALLOWED = 9
SEPARATOR_NOT_ALLOWED = 10
HEADER_TOO_LONG = 11
UNKNOWN_DP_ERROR = 12
ACCESS_DENIED = 13
DP_OUT_OF_MEMORY = 14
DISK_FULL = 15
DP_TIMEOUT = 16
OTHERS = 17
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
LOOP AT it_input.
write : it_input-line.
ENDLOOP.
before doing the below steps just takethe controle record and trail record cutt of from the table input based up on the length
split it_input-line AT '000' INTO TABLE it_header IN CHARACTER MODE.
LOOP AT it_header.
split it_header AT '0001' INTO TABLE it_item IN CHARACTER MODE.
write :/ it_header.
ENDLOOP.
after this you need to cut the records in tocorresponding fields in to respective tables by putting loop on item and header table as i decleared above.
i think this may solve your problem you need to keep some minnor effort.
Regaurds,
Sree.. -
Split data into different fields in TR
I have a flat file with space (multiple spaces between different fields) as a delimiter. The problem is, file is coming from 3rd party and they don't want to change the separator as comma or tab delimited CSV file. I have to load data in ODS (BW 3x).
Now I am thinking to load line by line and then split data into different objects in Transfer rules.
The Records looks like:
*009785499 ssss BC sssss 2988 ssss 244 sss 772 sss 200
*000000033 ssss AB ssss 0 ssss 0 ssss 0 ssss 0
*000004533 ssss EE ssss 8 ssss 3 ssss 2 ssss 4
s = space
Now I want data to split like:
Field1 = 009785499
Field2 = BC
Field3 = 2988
Field4 = 244
Field5 = 772
Field6 = 200
After 1st line load, go to 2nd line and split the data as above and so on. Could you help me with the code pleaseu2026?
Is it a good design to load data? Any other idea?
I appreciate your helps..Hi,
Not sure how efficient this is, but you can try an approach on the lines of this link /people/sap.user72/blog/2006/05/27/long-texts-in-sap-bw-modeling
Make your transfer structure in this format. Say the length of each line is 200 characters. Make the first field of the structure of length 200. That is, the length of Field1 in the Trans Struc will be 200.
The second field can be the length of Field2 as you need in your ODS, and similarly for Field3 to Field6. Load it as a CSV file. Since there are no commas, the entire line will enter into the first field of the Trans Structure. This can be broken up into individual fields in the Transfer Rules.
Now, in your Start Routine of transfer rules, write code like this (similar to the ex in the blog):
Field-symbols <fs> type transfer-structure.
Loop at Datapak assigning <fs>.
split <fs>-Field1 at 'ssss' into <fs>-field1 <fs>-field2 <fs>-field3....
modify datapak from <fs>
endloop.
Now you can assign Field1 of Trans Struc to Field1 of Comm Struc, Field2 of Trans Struc to Field2 of Comm Struc and so on.
Hope it helps!
Edited by: Suhas Karnik on Jun 17, 2008 10:28 PM -
Split records into two files based on lookup table
Hi,
I'm new to ODI and want to know on how I could split records into two files based on a value in one of the columns in the table.
Example:
Table:
my columns are
account name country
100 USA
200 USA
300 UK
200 AUS
So from the 4 records I maintain list of countries in a lookup file and split the records into 2 different files based on values in the file...
Say I have records AUS and UK in my lookup file...
So my ODI routine should send all records with country into file1 and rest to file2.
So from above records
File1:
300 UK
200 AUS
File2:
100 USA
200 USA
Can you help me how to achieve this?
Thanks,
Sam1. where and how do i create filter to restrict countries? In source or target? Should I include some kind of filter operator in interface.
You need to have the Filter on the Source side so that we can filter records accordingly the capture the same in the File. To have a Filter . In the source data store click and drag the column outside the data store and you will have Cone shaped icon and now you can click and type the Filter.
Please look into this link for ODI Documentation -http://www.oracle.com/technetwork/middleware/data-integrator/documentation/index.html
Also look into this Getting started guide - http://download.oracle.com/docs/cd/E15985_01/doc.10136/getstart/GSETL.pdf . You can find information as how to create Filter in this guide.
2. If I have include multipe countries like (USA,CANADA,UK) to go to one file and rest to another file; Can I use some kind of lookup file...? Instead of modifying filter inside interface...Can i Update entries in the file?
there are two ways of handling your situation.
Solution 1.
1. Create Variable Country_Variable
2. Create a Filter in the Source datastore in the First Interface ( SOURCE.COLUMN = #Country_Variable)
3. Create a new Package Country File Unload
4. Call the Variable in Country_Variable in Set Mode and provide the Country (USA )
5. Next call the First Interface
6. Next call the Second Interface where the Filter condition will be ( SOURCE.COLUMN ! = #Country_Variable )
7. Now run the package .
Solution 2.
If you need a solution to handle through Filer.
1. Use this Method (http://odiexperts.com/how-to-refresh-odi-variables-from-file-%E2%80%93-part-1-%E2%80%93-just-one-value ) to call the File where you wish to create store the country name into the variable Country_Variable
2. Pretty much the same Create a Filter in the Source datastore in the First Interface ( SOURCE.COLUMN = #Country_Variable)
3.Create a new Package Country File Unload
4.Next call the Second Interface where the Filter condition will be ( SOURCE.COLUMN ! = #Country_Variable )
5. Now run the package .
Now through this way using File you can control the File.
Please try and let us know , if you need any other help. -
How to Split field into multiple fields in Import Manager without delem
Hi
Is there any method to Split a record in MDM without using delimitter?
I dont want to use any delemitter My field content in Source is PRODLABELPACK and I want to split it into 3 fields in destination Field1= PROD
Field2=LABEL Field3=PACK
I know how to split it if the content is PROD_LABEL_PACK .But we dont want to use delimiter in the firld and want to use some substring function
Regards
PrashantYou Can use below FM SWA_STRING_SPLIT -
First Use READ_TEXT FM.
then loop into
loop at tline.
Here use 'SWA_STRING_SPLIT' -> Pass tdline and append the text into other internal table.
endloop
Thank you
Seshu -
Splitting Application into separate projects
I'd tried to split my domain layer (annotated EJB3) into separate project, from my service layer (EJB3 session beans) - that used to run together happily but I got the following error against each entity.
Exception [TOPLINK-198] (Oracle TopLink - 10g Release 3 (10.1.3.0.0) (Build 060118)): oracle.toplink.exceptions.DescriptorException
Exception Description: In order to use ObjectChangeTrackingPolicy or AttributeChangeTrackingPolicy, class com.davinci.capital.domain.tran.Tran has to implement ChangeTracker interface.
Descriptor: RelationalDescriptor(com.davinci.capital.domain.tran.Tran --> [DatabaseTable(TRAN)])
When I put the projects back together I still got the problem. I think it might be related to the enhancement process and somehow picking the un-enhanced code.
Is there someway to 'reset' a project/application? I tried removing the project (and leaving the source) and then creating a new one with the source still in place, but the error remains.
Any ideas?
Thanks
Michael
Message was edited by:
mmcgovernSomewhat answered this myself.
Appears that I had some unenhanced domain class files lying around in the DAO layer - these where getting picked up instead of the enhanced ones.
However it appears I there is a problem having EJBs spread around different projects within the application. The above problem appears to be related to having two-way dependencies so I get two copies of classes file created - and it picks up the unenhanced one.
The real problem is that I can't have EJB's in multiple projects - its appears to only create an ejb-jar.xml for EJBs in the "target" project (embedded OC4J) - the EJB's in the related projects are ignored.
If could split EJBs into projects then I would not have two-way dependencies and the original problem goes away.
Any ideas?
null -
When downloading a CD album, if it contains different artists, the album is split up into separate albums/icons. How do I get all songs into one album (just like the original CD)?
Generally, in iTunes, all you need to do is fill in an appropriate Album Artist to keep things together. For older iPods each track from the same album should have the same artist, or be marked as a compilation where appropriate. For iOS devices you may need to go to Settings > Music > Group By Album Artist > On.
For more details see my article on Grouping Tracks Into Albums, in particular the topic One album, too many covers.
tt2 -
Revision: 1384
Author: [email protected]
Date: 2008-04-24 07:54:58 -0700 (Thu, 24 Apr 2008)
Log Message:
Splitting DefineFont into the various DefineFont 1, 2, 3, etc SWF tag formats but retaining a common base DefineFont class so that embedded fonts are still retained as symbols for the SWF dictionary no matter what version of the SWF tag is used.
Also improving [Embed] so that it can recognize .TTC files as assets (previously these were only recognized through CSS @font-face rules).
QE: Yes, please add a test case for using [Embed] to embed fonts from a TTC file in addition to our tests for @font-face. Note that the AFEFontManager must be configured for this scenario.
Doc: No
Checkintests: Pass
Mxunit: AtEmbed Font suite: Pass
Modified Paths:
flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/media/AbstractTranscoder.java
flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/media/FontTranscoder.java
flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/util/MimeMappings.java
flex/sdk/trunk/modules/compiler/src/java/flex2/tools/PreLink.java
flex/sdk/trunk/modules/swfutils/src/java/flash/fonts/CachedFontManager.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/Dictionary.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/MovieEncoder.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/TagDecoder.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/TagEncoder.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/TagHandler.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/TagValues.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/builder/tags/FontBuilder.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/tags/DefineFont.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/tags/DefineFontAlignZones.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/tags/DefineFontInfo.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/tools/SwfxPrinter.java
Added Paths:
flex/sdk/trunk/modules/swfutils/src/java/flash/fonts/DefineFont3Face.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/tags/DefineFont1.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/tags/DefineFont2.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/tags/DefineFont3.java
flex/sdk/trunk/modules/swfutils/src/java/flash/swf/tags/DefineFont4.java
Removed Paths:
flex/sdk/trunk/modules/swfutils/src/java/flash/fonts/DefineFontFace.javaRunning the script by python2 solves it for me:
su - mythtv -c "nice -n 19 python2 /usr/bin/tv_grab_nl_py --output ~/listings.xml"
Best regards,
Cedric -
video downloaded from DVD will not split into clips for editing how can I split into clips. The DVD is from an old camerea not compatable with windows 7 so have to download from DVD . jules
juliej44
It sounds like whatever was put on disc was put on a DVD-R Intenso brand disc.
Probably the tape content was put on that DVD-R disc in DVD-VIDEO format. It gets more complicated if it gets put on the DVD-RAM type disc (which does not seem to be the case).
To verify the format of the material on your DVD disc, put the disc in the burn tray, go to computer, and Open the drive. You should see at least two folders, OpenDVD, VIDEO_TS, and maybe AUDIO_TS. Those folders are indicative of a DVD-VIDEO format.
http://www.fileinfo.com/help/video_ts_folder
Now back to Premiere Elements and the Video Importer. The video editor is not going to rip off clips from the DVD-VIDEO format. It is going to rip off VOB video files which contain a fixed number of files before it generates additional of its kind for additional video content.
Once you have the video VOB files (typically starting with VTS_01_1.VOB...spot the larger file size ones), in the Video Importer, you bring them into the project where you split them into clips that you want. You can do that in the Preview Window with the Set In Set Out point.
http://help.adobe.com/en_US/premiereelements/using/WSA27F29AF-97BB-4bdc-AF98-65113182EDF6. html
http://www.atr935.blogspot.com/2013/06/pe11-project-assets-organization-for.html
Please review the above and then let us know if any of it helped for the task that you want to perform with Premiere Elements.
Thanks.
ATR
Maybe you are looking for
-
How do you eject a CD stuck in the drive from an imac that won't start?
My Imac won't start. Its stuck on the Apple screen with the little gear going around. Other discussion have suggesting trying to boot directly from the install disc, which I want to try but can't because when it crashed there was a DVD in the optical
-
Hello All, I have sap BI installed on server A. Now I can access BI from my local machine. Now I installed BO edge series on my local machine and followed all the steps mentioned in Ingo Hilgefort 's blogs. when i logon to CMC using administrator I
-
Some sites are displayed weird on 64bit version on Ubuntu, 32bit version is ok
most text are invisible. the same thing happened to other sites too, like http://forums.yourkit.com/viewtopic.php?f=3&t=3131
-
Playing wav files at different pitch
Hi! I get the impression that the java sound package is overcomplicated. What I want to do is to generate music by playing sound files at different pitch (nothing special, I think). This means, program start -> load some files. mouse click -> play a
-
can i upgrade my ipod touch 2g to ios5