Static NAT - VPN - Internet Access
Does anyone know how to configure the following?
1. An static NAT from an inside ip address to another inside ip address (not physical subnet).
2. The traffic static Natted at the step 1 need to go into a tunnel VPN and at the same time to have internet access.
My router just have two interfaces a WAN and a LAN.
I just created the VPN, the static NAT and the PAT for other users of the subnet to have internet access, but the traffic static Natted just goes over the ipsec tunnel but cannot have internet access.
I tried to apply a route map after the static nat command but since i do not have a physical interface in the same subnet were i am translating the route-map is not applied to the static nat command.
in an extract:
LAN traffic (specific server) --->> static nat to inside not real subnet --->> traffic goes over Tunnel (OK), but no internet access.
BTW. I need to configure the nat before de ipsec tunnel because both lan subnets of the ipsec tunnel endpoint are the same.
Why do you need an inside host to be natted to another inside IP address?
You need to configure a "no nat" policy, for the internet traffic.
Similar Messages
-
NAT overload has been done successfully as follows:
1. ip nat inside and ip nat outside configured on the appropriate interfaces i.e.fa0/0 and fa0/1
2. default route added on the router.
3.additional configuration is added:
ip nat inside source list 1 interface fa0/1 overload
access-list 1 permit 192.168.1.0 0.0.0.255
Now I am trying to use static NAT for FTP:
ip nat inside source static tcp 192.168.1.X 21 x.x.x.x 21 extendable
But this does not work please help. I am trying to access FTP server from LAN by entering public address in the browser. Can access the FTP server with private address but this defeats the purpose of FTP. Please help.Router(config)#interface fa0/0
Router(config-if)#ip address 192.168.1.254 255.255.255.0
Router(config-if)#no shut
Router(config-if)#ip nat inside
Router(config-if)#interface fa0/1
Router(config-if)#ip address 203.109.120.2 255.255.255.252
Router(config-if)#no shut
Router(config-if)#ip nat outside
Router(config)#ip route 0.0.0.0 0.0.0.0 interface fa0/1
Router(config)#ip nat inside source list 1 interface fa0/1 overlaod
Router(config)#access-list 1 permit 192.168.1.0 0.0.0.255 -
IPad and PPTP VPN - Internet access (e-mail & Safari) not working
Hi there!
I've got an iPad2 (WiFi only) and need to configure it to use Witopia PPTP VPN, which is the VPN provider I've been using for a long time on my desktop and netbook.
Configure the iPad was an easy task, and I was able to successfuly authenticate and establish a PPTP session with any of the Witopia servers.
The problem is that once established the PPTP session, if the "send all traffic" option is ON, I have no Internet access at all (no e-mail neither browsing with Safari). Then, if I stop VPN, turn OFF the "send all traffic" option in the iPad, and start VPN again, I have Internet communication back and everything starts working fine. I've been fiddling with this in my home network (D-Link Dir-655 router using the IP 192.168.0.1 addressing scheme for my LAN).
Obviously, I decided to leave the "send all traffic" option OFF, but then I discovered that doing this my Safari traffic is not encrypted and my IP is not masked, i.e. the VPN is up and running, I have normal Internet traffic, but the service to be provided by the VPN for some inknown reason is not happening.
Does anyone have a clue about what's going on ?
TIA
RTadeuHave you tried a battery pull? If not, give that a try and then try again.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you! -
Have 5 macs on an ethernet network - some wired and some wireless to a Linksys router. My provider uses static IP and DSL for internet access. I am replacing an existing Linksys router with the Time Capsule. The Static IP settings I have are IP address, Gateway, Mask, primary DNS and secondary DNS. The Airport Utility is not as straight forward as the Linksys setup. There is not a place to list gateway. Consequently I am unable to connect to the internet and am back on the Linksys router until I get this resolved. Any suggestions would be much appreciated !
You enter the static public IP address info on the TCP/IP tab within the Airport Utility. For a static address, use Configure IPv4 = Manually. You use the Router field for the Gateway address.
-
Hello,
I have a question about setting up a VPN connect, I have a Cisco VPN profile which is configured to exclude and include some IP addresses to be able to access some internet sites during connected to that VPN.
On Mac OS X 10.9.2 I have setup a native VPN yet I cannot find a way to exclude/include those ip addresses.
Is there any way to do that?The only place I know to add IP addresses and/or Domain Names is in your OS X VPN connection within System Preferences/Network.
Select your VPN connection then click the Advanced button. Click the DNS tab and this is where IP addresses (DNS Servers) and Domain Names (Search Domains) can be entered. -
Centralize internet access in MPLS VPN
Can i implement Centralize internet access (the Hub CE Router to performs NAT) in cisco MPLS VPN solution?
If so, is there any example about that? i can't find it at CCO~
Thanks a lot~If you run dynamic routing protocol in PE-CE,like rip2,ospf,bgp,do the following task.
1:set a default route in HUB CE;and generate the default route under its dynamic protocol.
2:in other CEs, make sure they can learn this route.
If you run static route and vrf static route between CE and PE,do the following task.
1.set default route in HUB CE, and set default route in other CEs.
2.In all PEs,redistribute the connected and static rotues to address-family ipv4 of customer vrf.
3.set the customer vrf default route in all PE which connected your all CEs.
Note: make sure all PEs can reach the GW address of vrf deafult route. GW IP address is the interface of which HUB CE towards PE.
command: "ip route vrf 0.0.0.0 0.0.0.0 global.
TRY -
NAT for remote access VPN clients
Hello,
I have a simple remote access VPN setup on a 2811 router. The remote subnet of the clients connecting have access to the local LAN subnet, but I am wondering if it is possible to somehow NAT those remote access users, so that they can go beyond the local LAN, and through the VPN routers outside connection, giving them access to other resources.
The remote subnet would need to be added to the NAT overload pool that the local LAN is on somehow, but since no interface is created, I am unsure where I would need to put "ip nat inside" if it even needs to be done, or if I am just missing something.
I guess really what I want to do is tunnel all traffic, and have that remote client IP translate to the NAT pool on the router for internet access.
Thanks.Have a look here for solution
http://www.cisco.com/en/US/products/sw/secursw/ps2308/products_configuration_example09186a008073b06b.shtml
Regards -
Static-nat and vpn tunnel bound traffic from same private address?
Hi guys,
I have site-to-site tunnel local host @192.168.0.250 and remote-host @172.16.3.3.
For this local host @192.168.0.250, I also have a static one-to-one private to public.
static (mgmt-192,outside-50) 216.9.50.250 192.168.0.250 netmask 255.255.255.255
As you can see, IPSec SA shows end-points in question and traffic is being decrypted but not encrypted host traffic never enter into the tunnel, why?
How can I resolve this problem, without complicating the setup ?
BurlingtonASA1# packet-tracer input mgmt-192 icmp 192.168.0.250 8 0 172.16.3.3
Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 outside-50
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.0.0 255.255.255.0 mgmt-192
Phase: 5
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group mgmt_intf in interface mgmt-192
access-list mgmt_intf extended permit icmp any any
access-list mgmt_intf remark *** Permit Event02 access to DMZ Intf ***
Additional Information:
Phase: 6
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: NAT-EXEMPT
Subtype:
Result: ALLOW
Config:
nat-control
match ip mgmt-192 host 192.168.0.250 outside-50 host 172.16.3.3
NAT exempt
translate_hits = 5, untranslate_hits = 0
Additional Information:
Phase: 9
Type: NAT
Subtype:
Result: ALLOW
Config:
static (mgmt-192,outside-50) 216.9.50.250 192.168.0.250 netmask 255.255.255.255
nat-control
match ip mgmt-192 host 192.168.0.250 outside-50 any
static translation to 216.9.50.250
translate_hits = 25508, untranslate_hits = 7689
Additional Information:
Phase: 10
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (mgmt-192,dmz2-172) 192.168.0.0 192.168.0.0 netmask 255.255.255.0
nat-control
match ip mgmt-192 192.168.0.0 255.255.255.0 dmz2-172 any
static translation to 192.168.0.0
translate_hits = 28867754, untranslate_hits = 29774713
Additional Information:
Phase: 11
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional Information:
Phase: 12
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 1623623685, packet dispatched to next module
Result:
input-interface: mgmt-192
input-status: up
input-line-status: up
output-interface: outside-50
output-status: up
output-line-status: up
Action: allow
BurlingtonASA1#
Crypto map tag: map1, seq num: 4, local addr: 216.9.50.4
access-list newvpn extended permit ip host 192.168.0.250 host 172.16.3.3
local ident (addr/mask/prot/port): (192.168.0.250/255.255.255.255/0/0)
remote ident (addr/mask/prot/port): (172.16.3.3/255.255.255.255/0/0)
current_peer: 216.9.62.4
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 53, #pkts decrypt: 53, #pkts verify: 53
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 216.9.50.4, remote crypto endpt.: 216.9.62.4
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: 37CA63F1
current inbound spi : 461C843C
inbound esp sas:
spi: 0x461C843C (1176273980)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, }
slot: 0, conn_id: 77398016, crypto-map: map1
sa timing: remaining key lifetime (kB/sec): (3914997/25972)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x003FFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0x37CA63F1 (936010737)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, }
slot: 0, conn_id: 77398016, crypto-map: map1
sa timing: remaining key lifetime (kB/sec): (3915000/25972)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001Hi
intersting VPN ACL
object-group network DM_INLINE_NETWORK_18
network-object YYY.YYY.YYY.0 255.255.255.0
object-group network DM_INLINE_NETWORK_22
network-object UUU.UUU.UUU.0 255.255.255.0
access-list outside_access_in extended permit ip object-group DM_INLINE_NETWORK_22 object-group DM_INLINE_NETWORK_18
Static NAT
static (Inside,outside) XXX.XXX.XXX.171 YYY.YYY.YYY.39 netmask 255.255.255.255
No NAT
object-group network DM_INLINE_NETWORK_20
network-object UUU.UUU.UUU.0 255.255.255.0
access-list Inside_nat0_outbound extended permit ip ZZZ.ZZZ.ZZZ.0 255.255.255.0 object-group DM_INLINE_NETWORK_20
VPN CLient Pool
No pool configured as it uses the interesting traffic or protected traffic in ASDM - UUU.UUU.UUU.0 is the IP address range at the far side of the site to site VPN.
I hope this helps
Thanks -
Static NAT causes unable to access server via internal IP
Hi all,
Need some help. I running site-to-site IPsec VPN in Cisco 2811 IOS 12.4 both site. Here I encounter a problem to access server on Site A from Site B
Site A having Leased Line connected to router with Public IP. I have done static mapping 1 web server to Public IP (NAT). This to allow external users to access the server via Public IP. At the same time, users at Site B would need to access to same server via Internal IP since they have Site-to-Site VPN established. But once I done Static Mapping (NAT), user at Site B unable to access the server at Site A using its internal IP. But external user can access server via Public IP. What went wrong here. Do i need to add extra command to get this done? We really need this.Hi sheik,
I'm accessing the server form Site B using its server's LAN IP.
If I remove the static NAT statement from my router at Site A, everything works well. I can access the server from site B using its LAN IP via Site-to-Site VPN. But in this case, external users unable to access server via Public IP since no Static NAT statement. -
No Internet access after cisco vpn client connection
Hi Experts,
Kindly check below config.the problem is vpn is connected but no internet access
on computer after connecting vpn
ASA Version 8.0(2)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Ethernet0/0
nameif outside
security-level 0
ip address 192.168.10.10 255.255.255.0
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.14.12 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list dubai_splitTunnelAcl standard permit 192.168.14.0 255.255.255.0
access-list INSIDE_nat0_outbound extended permit ip any 192.168.14.240 255.255.2
55.240
pager lines 24
mtu inside 1500
mtu outside 1500
ip local pool testpool 192.168.14.240-192.168.14.250
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list INSIDE_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.14.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set setFirstSet esp-3des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set setFirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
username testuser password IqY6lTColo8VIF24 encrypted
username khans password X5bLOVudYKsK1JS/ encrypted privilege 15
tunnel-group mphone type remote-access
tunnel-group mphone general-attributes
address-pool testpool
tunnel-group mphone ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
: end
ciscoasa#Hi Harish,
Please check the o/ps below and route print in attached file
Latest ASA Config
ASA Version 8.0(2)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Ethernet0/0
nameif outside
security-level 0
ip address 192.168.10.10 255.255.255.0
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.14.12 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list dubai_splitTunnelAcl standard permit 192.168.14.0 255.255.255.0
access-list INSIDE_nat0_outbound extended permit ip any 192.168.14.0 255.255.255
.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip local pool testpool 192.168.15.240-192.168.15.250
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.14.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set setFirstSet esp-3des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set setFirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
no crypto isakmp nat-traversal
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
group-policy mphone internal
group-policy mphone attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value dubai_splitTunnelAcl
username testuser password IqY6lTColo8VIF24 encrypted privilege 15
username testuser attributes
vpn-group-policy mphone
username khans password X5bLOVudYKsK1JS/ encrypted privilege 15
username khans attributes
vpn-group-policy mphone
tunnel-group mphone type remote-access
tunnel-group mphone general-attributes
address-pool testpool
tunnel-group mphone ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:12308d7ff6c6df3d71181248e8d38ba8
: end
ciscoasa#
Route Print after vpn connection
C:\>route print
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x40003 ...00 24 01 a2 e6 f1 ...... D-Link DFE-520TX PCI Fast Ethernet Adapter -
Packet Scheduler Miniport
0x250004 ...00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter - Packet Schedule
r Miniport
===========================================================================
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.10.1 192.168.10.211 20
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.10.0 255.255.255.0 192.168.10.211 192.168.10.211 20
192.168.10.211 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.10.255 255.255.255.255 192.168.10.211 192.168.10.211 20
192.168.14.0 255.255.255.0 192.168.15.1 192.168.15.240 1
192.168.15.0 255.255.255.0 192.168.15.240 192.168.15.240 20
192.168.15.240 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.15.255 255.255.255.255 192.168.15.240 192.168.15.240 20
213.42.233.97 255.255.255.255 192.168.10.1 192.168.10.211 1
224.0.0.0 240.0.0.0 192.168.10.211 192.168.10.211 20
224.0.0.0 240.0.0.0 192.168.15.240 192.168.15.240 20
255.255.255.255 255.255.255.255 192.168.10.211 192.168.10.211 1
255.255.255.255 255.255.255.255 192.168.15.240 192.168.15.240 1
Default Gateway: 192.168.10.1
===========================================================================
Persistent Routes:
None
C:\>
C:\>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : asu
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection 7:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : D-Link DFE-520TX PCI Fast Ethernet A
dapter
Physical Address. . . . . . . . . : 00-24-01-A2-E6-F1
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.10.211
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.10.1
DNS Servers . . . . . . . . . . . : 213.42.20.20
195.229.241.222
Ethernet adapter Local Area Connection 8:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Cisco Systems VPN Adapter
Physical Address. . . . . . . . . : 00-05-9A-3C-78-00
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.15.240
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : -
Static Policy NAT in VPN conflicts with Static NAT
I have a situation where I need to create a site-to-site VPN between an ASA 5505 using IOS 7.2 and a Sonicwall NSA4500. The problem arises in that the LAN behind the Cisco ASA has the same subnet as a currently existing VPN created on the Sonicwall. Since the Sonicwall can't have two VPNs both going to the same subnet, the solution is to use policy NAT on the ASA so that to the Sonicwall, the new VPN appears to have a different subnet.
The current subnet behind the ASA is 192.168.10.0/24 (The Sonicwall already has a VPN created to a different client with that same subnet). I am trying to translate that to 192.168.24.0/24. The peer LAN (behind the Sonicwall) is 10.159.0.0/24. The pertinent configuration of the ASA is:
interface Vlan1
ip address 192.168.10.1 255.255.255.0
access-list outside_1_cryptomap extended permit ip 192.168.24.0 255.255.255.0 10.159.0.0 255.255.255.0
access-list VPN extended permit ip 192.168.10.0 255.255.255.0 10.159.0.0 255.255.255.0
static (inside,outside) 192.168.24.0 access-list VPN
crypto map outside_map 1 match address outside_1_cryptomap
In addition to this, there are other static NAT statements and their associated ACLs that allow certain traffic through the firewall to the server, e.g.:
static (inside,outside) tcp interface smtp SERVER smtp netmask 255.255.255.255
The problem is this: When I enter the static policy NAT statement, I get the message "Warning: real-address conflict with existing static" and then it refers to each of the static NAT statements that translate the outside address to the server. I thought about this, and it seemed to me that the problem was that the policy NAT statement needed to be the first NAT statement (it is last) so that it would be handled first and all traffic destined for the VPN tunnel to the Sonicwall (destination 10.159.0.0/24) would be correctly handled. If I left it as the last statement, then the other static NAT statements would prevent some traffic destined for the 10.159.0.0/24 network from being correctly routed through the VPN.
So I tried first to move my policy NAT statement up in the ASDM GUI. However, moving that statement was not permitted. Then I tried deleting the five static NAT statements that point to the server (one example is above) and then recreating them, hoping that would then move the policy NAT statement to the top. This also failed.
What am I missing?Hi,
To be honest it should work in the way I mentioned. I am not sure why it would change the order of the NAT configurations. I have run into this situation on some ASA firewalls running the older software (older than 8.2) and the reordering of the configurations has always worked.
So I am not sure are we looking at some bug or what the problem is.
I was wondering if one solution would be to configure all of the Static NAT / Static PAT as Static Policy NAT/PAT
I have gotten a bit rusty on the older (8.2 and older) NAT configuration format as over 90% of our customer firewalls are running 8.3+ software.
I was thinking of this kind of "static" configuration for the existing Static PAT configurations if you want to try
access-list STATICPAT-SMTP permit tcp host eq smtp any
static (inside,outside) tcp interface smtp access-list STATICPAT-SMTP
access-list STATICPAT-HTTPS permit tcp host eq https any
static (inside,outside) tcp interface https access-list STATICPAT-HTTPS
access-list STATICPAT-RDP permit tcp host eq 3389 any
static (inside,outside) tcp interface 3389 access-list STATICPAT-RDP
access-list STATICPAT-TCP4125 permit tcp host eq 4125 any
static (inside,outside) tcp interface 4125 access-list STATICPAT-TCP4125
access-list STATICPAT-POP3 permit tcp host eq pop3 any
static (inside,outside) tcp interface pop3 access-list STATICPAT-POP3
Naturally you would add the Static Policy NAT for the VPN first.
Again I have to say that I am not 100% sure if this was is the correct format maybe you can test it with a single service that has a Static PAT. For example the Static PAT for RDP (TCP/3389). First entering the Static Policy NAT then removing the Static PAT and then entering the Static Policy PAT.
Remember that you should be able to test the translations with the "packet-tracer" command
For example
packet-tracer input outside tcp 1.1.1.1 12345
- Jouni -
This maybe stupid but may somebody help on this.
Site A --- Internet --- Site B
An IPSec VPN is implemented between Site A and Site B. Some "nat 0" commands are used on Site A PIX to avoid addresses being translated when communicating with site B.
But now there is a problem, there are several public servers which have static NAT entries by "static" command. And it looks like these entry will still be valid even if the "nat 0" is presenting. And thus those inside IPs which have a static NAT, will be translated once it reaches the PIX and can not go via the VPN tunnel.
May someone advise me how to overcome this? Thanks.Your question really pertains to the nat order of operations. Nat 0 (nat exemption) is first in the order. It preceeds all other including static nat. The servers you mention will absolutely be included in the nat 0 unless they are specifically denied in the nat 0 acl.
-
Hi
I could not quite find any information that was close enough to my problem that would enable me to solve it so hence I am now reaching out to you guys.
I have a Cisco ASA running 8.2(1) and I am using ASDM to manage the firewall. I have a Linux VPN server on the inside with and IP address of YYY.YYY.YYY.39 with a static NAT to the outside with an address of XXX.XXX.XXX.171 .
I have a site to site VPN tunnel which terminates on the outside of the ASA on the outside interface XXX.XXX.XXX.190 .
Traffic from the YYY.YYY.YYY.0/24 network can't transverse the site to site VPN as there is a conflict of IP address's on the far side so it is natted via a dynamic policy to host address ZZZ.ZZZ.ZZZ.100
Users remote into the inside(YYY.YYY.YYY.0/24) for support via the Linux VPN server (.39) and then need to communicate down the site to site VPN. The problem is that the static NAT for the incomming connections takes preference and bypasses the site to site VPN tunnel for outbound traffic. I tried to create a policy Static nat but it tries to modify the static nat that handels the incomming traffic to the Linux server.
I hope the above makes sense.Hi
intersting VPN ACL
object-group network DM_INLINE_NETWORK_18
network-object YYY.YYY.YYY.0 255.255.255.0
object-group network DM_INLINE_NETWORK_22
network-object UUU.UUU.UUU.0 255.255.255.0
access-list outside_access_in extended permit ip object-group DM_INLINE_NETWORK_22 object-group DM_INLINE_NETWORK_18
Static NAT
static (Inside,outside) XXX.XXX.XXX.171 YYY.YYY.YYY.39 netmask 255.255.255.255
No NAT
object-group network DM_INLINE_NETWORK_20
network-object UUU.UUU.UUU.0 255.255.255.0
access-list Inside_nat0_outbound extended permit ip ZZZ.ZZZ.ZZZ.0 255.255.255.0 object-group DM_INLINE_NETWORK_20
VPN CLient Pool
No pool configured as it uses the interesting traffic or protected traffic in ASDM - UUU.UUU.UUU.0 is the IP address range at the far side of the site to site VPN.
I hope this helps
Thanks -
MPLS-VPN w/NAT for Internet connectivity.
We have implemented MPLS-VPN and site-to-site connectivity seems to be working fairly well. However, we are having strange issue when trying to access the Internet. For some odd reason, we are not able to get to some sites such as ebay.com, latimes.com, nytimes.com, moviefone.com. We are running dynamic NAT and the topology looks like this:
Laptop----CE-------PE-----NAT------BR-----Internet
This is a simple layout of what we have currently in the lab. NAT router is not running MPLS but we are using VRF to create sub-interfaces on FE connecting PE and NAT router for each customers. I have access-list allowing 10.x.x.x/8.
Laptop-CE - 10.0.0.8/30
CE-PE - 10.0.0.0/30
PE-NAT - 10.0.1.0/30
Also, we are able to ping, trace, ftp, use remote desktop, pcanywhere. It seems to be only affecting http. We've been working on this for couple of days now and we've hit a wall. Any help will be greatly appreciated.
JKI had a slightly different yet similar problem a few months ago on our mpls network with the CE devices, and turned out the DF bit had to be set to 0 to enable fragmentation _prior_ to traffic entering the core.
Fixed it right up by setting a policy on the ethernet port.
-Jeff -
DM-VPN with Static NAT for Spoke Router. Require Expert Help
Dear All,
This is my first time to write something .
i have configure DM-VPN, and it's working fine, now i want to configure static nat.
some people will think why need static nat if it's working fine.
let me tell you why i need. what is my plan.
i have HUB with 3 spoke. some time i go out side of my office and not able to access my spoke computer by Terminal Services. because its by dynamic ip address. so what i think i'll give one Static NAT on my HUB Router that if any one or Me Hit the Real/Public IP address of my HUB WAN Interface from any other Remote location so redirect this quiry to my Terminal Service computer which located in spoke network.
will for that i try but fail.
will again the suggestion will come. why not to use .. Easy VPN. well sound great. but then i have to keep my notebook with me.
i'll also do it but now i need that how to do Static NAT. like for normal Router i am doing which is not part of VPN.
ip nat inside source static tcp 192.168.1.10 3389 interface Dialer1 3389
but this time this command is not working, because the ip address which i mention it's related HUB Network not Spoke
spose spoke Network: 192.168.2.0/24
and i want on HUB Router:
ip nat inside source static tcp 192.168.2.10 3389 interface Dialer1 3389
i am using Cisco -- 887 and 877 ADSL Router.
but it's not working, Need experts help. please write your comment's which are very important for me. waiting for your commant's
fore more details please see the diagram.
for Contact Me: [email protected]hi rvarelac thank you for reply :
i allready done that , i put a deny statements in nat access-list excluding the vpn traffic , but the problem still there !
crypto isakmp policy 10
encr aes
authentication pre-share
crypto isakmp key 12344321 address 1.1.1.1
crypto ipsec transform-set Remote-Site esp-aes esp-sha-hmac
mode tunnel
crypto map s2s 100 ipsec-isakmp
set peer 1.1.1.1
set transform-set Remote-Site
match address vpnacl
interface GigabitEthernet0/0
crypto map s2s
Extended IP access list lantointernet
30 deny icmp 172.17.0.0 0.0.1.255 192.168.1.0 0.0.0.255
40 deny igmp 172.17.0.0 0.0.1.255 192.168.1.0 0.0.0.255
50 deny ip 172.17.0.0 0.0.1.255 192.168.1.0 0.0.0.255
80 permit ip any any
Maybe you are looking for
-
I purchased Elements 12 from the trial version and have been trying to download and install for a week now. I have encountered errors about the files being downloaded to seperate areas to files being unable to be unzipped and am currently getting ha
-
IN photoshop 10 when I export an album to a dvd, I can't op@en it on my computer with windows 7. Help
-
Can we disable the default push buttons on the ALV Grid
Hi, Can we disable the default push buttons on the ALV Grid Control... If so, pls send me the procedure... thanks and regards raghu
-
Duplicate Cell Contents n-times based on value in neighboring cell?
I have a sheet/table that contains ~150 rows of 2 columns: A B COUNT CONTENT I am looking for a way to duplicate each CONTENT in a new sheet/table COUNT times, and do this for each row. For example A B 2 RED 1 BLUE 3 GREEN Would give me a sheet/table
-
Substitution Syntax in PL/SQL Process
Hey all, I've got a good one for you. I used to be able to do the following in a pl/sql page process. declare l_vc_arr2 HTMLDB_APPLICATION_GLOBAL.VC_ARR2; begin SELECT ca.account_number BULK COLLECT INTO l_vc_arr2 FROM hz_cust_accounts ca, hphc_enrol