SuperDuper! clone & Snow Leopard

In my MacPro I have a two 1tb HD setup where the 2nd drive is an exact clone of the 1st using 'Superduper!' When I installed 'Snow Leopard' I chose to replace the 1st HD and test the system for a week before making a new clone. Having done so without any problems (SN actually seems to be a good solid update).
*My question is this: (updating or replacing the clone)*
Should I reformat the 2nd drive and make a completely fresh bootable clone of the 1st, or ask 'Superduper' to do a normal 'Smart Update', where it only changes what's different. I'm wondering since this is a major system update if this is indeed sensible, or am I just being too cautious?
+NB: I have updated to the latest SN friendly version of 'Superduper!'+

For safety, I would do a completely new Clone. Updating a clone with the same OS is one thing, but I would not be secure doing the same from one OS to another. This is the time to spend a little extra time to be sure all is going to be right in the future. Be sure and use the SL-ready version of SuperDuper (i.e., you may need to update SuperDuper).
Message was edited by: donv (The Ghost)

Similar Messages

  • Tiger 10.4.11 to Snow Leopard using USB PENDRIVE Help..!

    Dear All;
    I have an Intel macbook which had TIGER10.4.11 earlier. As i realised that snow Leopard can be Installed Bypassing "Leopard 10.5" i tried it out but in Vain. please see below;
    My Macbooks Internal Optical Drive has Fried as usual & the Install DVD of OS 10.6 is a 10A432 build (which i assume is enough for a SL clean install). connecting a USB External DVD drive i double clicked MAC OS X DVD on Tiger platform and followed the instructions which said to restart,on restart if i remember correctly (no customize options were present)and using Disk utility i erased the Whole internal drive thereby removing Tiger completely.
    Restored the "MAC OS X INSTALL DVD" to a new 8 gb hp Pendrive (after formatting in mac os- journaled).
    On startup clicked Option > chose USB install > clicked language Tab (Please Note no customize Tab or anything else was present which i assume is the case with all) . It showed "installing mac os x " and then a dialogue appeared saying +"Installation requires that Mac os x 10.5 be already insatlled on computer"+ alongwith two tabs RESTORE FROM BACKUP + Restart. Meanwhile the top menu Bar is inactive and greyed. so i chose "Restore from backup" at which point the top Menu bar becomes active. Using Disk Utility i made sure to frmat teh whole drive again but after quitting it there was no change and installation didnt move further.
    Please Tell me is it absolutely necessary to install 10.5 or is it some problem with USB or where else i maybe going wrong.
    I would be glad if any of you experts can clearly state the steps to Install Mac OS 10.6 on this macbook (with no OS whatsoever on a clean internal Disk) using only a USB Pendrive.
    Thanks much in Advance.

    Welcome to Apple Discussions!
    Regardless of what you do, you must backup your data at least twice before installing anything*:
    http://www.macmaps.com/backup.html
    Furthermore, make sure all your software is Snow Leopard compatible in these links:
    http://snowleopard.wikidot.com/
    http://support.apple.com/kb/HT3669
    Now as for your installation:
    Restored the "MAC OS X INSTALL DVD" to a new 8 gb hp Pendrive (after formatting in mac os- journaled).
    You are approaching it the wrong way. Either:
    1. Verify the PRAM battery of the Mac in question isn't dead. Sometimes internal "dead" optical drives get revived when the PRAM battery is replaced. Anytime a Mac is over 4 years, the battery might need replacing, and that might fix the optical drive.
    2. Connect a bootable optical drive to the Mac and run the installer from it to the hard drive of the Mac. http://www.macsales.com/ has both internal and external optical drives.
    3. Have a technician clean the drive and make sure your disc is usable on their computer to verify your problem isn't with your installer disc.
    Your pen drive is too small to install the operating system. You'd need a minimum of a 16GB pen drive to install. Furthermore, double check your machine has at least 1 GB of RAM in Apple menu -> About This Mac. 512MB of RAM, or 768MB of RAM won't cut it. If you choose a pen drive method, here's what you must do:
    4. Find another Mac of the same vintage and model with a working optical drive. Format a 16 GB pen drive GUID partitioning with Disk Utility. Install the operating system on the pen drive. Boot from the pen drive off the Mac with the bad optical drive, and use a cloning software such as Superduper, to clone Snow Leopard. Mind you this method would require you to erase the hard drive on the Mac. It is best if you just fix the optical drive on the other Mac if you wish to have a chance of preserving your data.
    Another thing I realized reading your post:
    dialogue appeared saying "Installation requires that Mac os x 10.5 be already insatlled on computer"
    If you got that dialog you are using the wrong disc. That disc is only to be used with Macs which shipped 3 weeks prior to Snow Leopard's release to the date of Snow Leopard's release. The $29.95 installer available from the Apple Store has no such limit. Your procedure of restoring I doubt will work with a flash drive. My method might work if you have the correct disc*:
    http://www.macmaps.com/bootcd.html
    - * Links to my pages may give me compensation.

  • Airport signal fades in snow leopard

    Since Snow Leopard arrived I was plagued by a fading airport signal and resorted to a USB adapter in place of Airport. After about 20 minutes of use Airport signal fades and the network is lost.
    A friend recently updated to Snow Leopard and has now got similar Airport and network problems.
    All day today I have been working off a SuperDuper clone of Leopard on an external drive. I use page layout software that is not available for Snow Leopard. The surprising thing is that Airport has been full strength all day.
    Is there a known problem?
    AW.

    I just downloaded the 10.6.2 update, and I can now print wirelessly to my HP 1012 via an older Airport Express! Give it a try. Maybe you'll be lucky, too!

  • Howto downgrade a MacBook Pro from Lion to Snow Leopard

    Preliminary:
    - another Mac running Snow Leopard 10.6.8
    - the Snow Leopard 10.6.3 Retail Install DVD
    - the Mac OS X 10.6.8 Update Combo v1.1 (http://support.apple.com/kb/DL1399)
    - Carbon Copy Cloner (http://bombich.com/)
    - 8GB USB stick
    ### Preparing a USB-Stick with a patched Snow Leopard 10.6.3 Install ###
    - Create an DVD/CD-Master image of the 10.6.3 Retail Install DVD with Disk Utility
    - Eject the 10.6.3 Retail Install DVD
    - Mount the new CDR image in a Terminal
    # hdiutil attach /Path/to/MacOSX-10.6.3-Install.cdr -readwrite
    - Change the current folder to the CDR image
    # cd /Volumes/Mac\ OS\ X\ Install\ DVD/
    - Double check that you are on the CDR image
    # pwd
    - Backup the Kernel
    # mv ./mach_kernel ./mach_kernel-10.6.3
    - Copy the new 10.6.8 Kernel from the Snow Leopard HD to the CDR image
    # sudo cp -pv /Volumes/SnowLeo-HD/mach_kernel ./
    - Copy the 10.6.8 Kernel Extensions from the Snow Leopard HD to the CDR image
    # sudo cp -Rpv /Volumes/SnowLeo-HD/System/Library/Extensions/* ./System/Library/Extensions/
    - Delete all Kext Caches on the CDR image
    # sudo rm -rf ./System/Library/Caches/com.apple.*
    # sudo rm -f ./System/Library/Extensions.mkext
    - edit the Boot.plist on the CDR image
    # sudo nano ./Library/Preferences/SystemConfiguration/com.apple.Boot.plist
    <?xml version="1.0" encoding="UTF-8"?>
    <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
    <plist version="1.0">
    <dict>
        <key>Kernel Flags</key>
        <string>-v -f -x</string>
    </dict>
    </plist>
    # cd
    - Now copy the content of the CDR image to the USB-Stick using Carbon Copy Cloner
    ### Snow Leopard Installation on MacBook Pro 8,2 ###
    - Boot your MacBook Pro from the USB-Stick
    - Install Snow Leopard
    - Reboot again from the USB-Stick
    - Select your language
    - Open a Terminal and type
    # cd /
    - Find your new MacBook SnowLeo-HD        
    # df -h
    - Copy the 10.6.8 Kernel    
    # cp -pv  ./mach_kernel /Volumes/MacBook_SnowLeo-HD/
    - Copy the 10.6.8 Kernel Extensions    
    # cp -Rpv ./System/Library/Extensions/* /Volumes/MacBook_SnowLeo-HD/System/Library/Extensions/
    - Exit Terminal
    - Repair permissions on your new MacBook SnowLeo-HD with Disk Utility
    - Quit Installer
    - Now boot from your new MacBook SnowLeo-HD in Secure Mode (hold down Shift while booting)
    - Repair permissions on your new MacBook SnowLeo-HD with Disk Utility
    - Update the Extensions Cache in a Terminal
    # sudo kextcache -e --local-root --system-cache (just ignore all warnings about invalid kexts)
    - Install the 10.6.8 Combo Update
    - Reboot

    Holy Moly!
    Your'e answer is really for those kids with no experience in a terminal.
    The command line is only for pro users and should no be used by any DAU. Therefore no problem at all with "rm -rf" if you have changed into the correct directory first.
    One suggetion is adding these lines to your "~/.profile"
    TERM=xterm-color
    # colors for misc things
    export TERM=xterm-color
    export GREP_OPTIONS='--color=auto' GREP_COLOR='1;32'
    export CLICOLOR=1
    # Set colors
    export LS_COLORS='di=1;36:fi=0:ln=4;34:pi=5:so=4;5:bd=5:cd=5:or=4;91:mi=4;92:ex=35:*.r b=90'
    alias rm="rm -i"
    alias cp="cp -i"
    PS1="(\u) \[\033[01;31m\]\h\[\033[01;34m\] [\w]# \[\033[00m\]"
    Than do a
    # source .profile
    at the terminal prompt in order to active the settings immediatelly.
    Now the "rm" command will always ask before deleting any file or folder.
    Unfortunately if you like to delete a folder containing other folders with several files inside you will go mad!
    One possible intermediate solution is
    # unalias rm; rm -rf ./System/Library/Caches/com.apple.*; alias rm="rm -i"
    But as mentioned before, if you have "sweaty fingers" while typing in Unix commands you should better stay away from the terminal.

  • Snow Leopard 10.6.1 Clone not appearing in Startup Disk

    Before attempting to upgrade to 10.6.2, I made a bootable clone using Disk Utility of 10.6.1. I followed the same procedure I used successfully to create a bootable clone of 10.4.11 just a few days ago on a separate partition of my external drive. After finishing the SL clone of 10.6.1, I went to Startup Disk because I wanted to test if the computer would boot from it, but my new SL clone wasn't there--just my internal hard drive and the Tiger clone. I tried ejecting the external drive, then reconnecting it, and now neither the Snow Leopard nor the Tiger clones appear in Startup Disk. They do appear in Disk Utility, and I verified both of them, so Disk Utility says they're okay, but Startup Disk doesn't see them at all.

    lakeshore wrote:
    I tried resetting PRAM, but that did nothing. The only thing I did earlier that might have caused this is that when I originally partitioned the drive, I named the volumes "Tiger Clone" and "Snow Leopard Clone." While making the bootable clone of SL, I noticed that Disk Utility automatically changed the name of that volume to "Macintosh HD." So immediately after the clone was finished, I went into Get Info and changed the name of it back to "Snow Leopard Clone." Then I checked Startup Disk, and the SL clone wasn't there, but the "Tiger Clone" was. I then changed the name of "Tiger Clone" to "10.4.11" and that's when the Tiger Clone volume disappeared from Startup Disk. Could changing the names of the volumes have the effect of the volumes no longer showing up in Startup Disk?
    this really should not matter. try this. run the following terminal command
    sudo bless --folder /volumes/"Snow Leopard Clone"/System/Library/CoreServices --bootinfo --bootefi
    you'll have to enter your admin password (which you won't see). that's normal. then see if it shows up in the startup disk preferences.
    If I have to access those clones using the option-hold restart, which seems to work for me, that's fine. I just want to make sure that the two clones on my external drive are safe and bootable.

  • Is there any way to clone a machine using boot camp running WinXP. The Mac side is running Snow Leopard. I want to clone a newly set up machine on to a number of machines in a student lab. I am wanting to clone both particians

    Is there any way to clone a machine using boot camp running WinXP. The Mac side is running Snow Leopard. I want to clone a newly set up machine on to a number of machines in a student lab. I am wanting to clone both particians

    AFAIK, there's no app that'll clone the Mac and PC volumes so you can restore them. System Image Utility.app or Deploy Studio for Mac and Ghost for PC are needed. See these for starters:
    http://clc.its.psu.edu/Labs/Mac/Resources/blastimageconfig/
    http://blog.macadmincorner.com/
    http://lists.apple.com/archives/System-imaging/

  • Can I clone Indesign CS3 from a Snow Leopard disk to a Lion disk, or will I need to reinstall Indesign from CD.

    I have a Mac Pro with CS3 and it has been updated from a previous version of CS. I don't have the previous version, so if I need to upgrade my Mac Pro can I just clone it (Snow Leopard) with the already installed CS applications onto a Lion hard drive? I am not sure if the extensions will work in Lion.

    OSX applications cannot run on external drives because there are usually several "system dependencies".  These dependencies are wide-spread and hard to track down manually.
    To "clone an application", you would need to clone each and every "system dependency", with the additional twist of finding the correct correlating Lion directory.

  • Rsync command line to optain a bootable snow leopard clone

    Hello,
    I want to do a bootable clone of my snow leopard system on an external hard drive. I am doing this from a shell script as I am doing other things via the script before.
    To accomplish this I am using rsync 3.0.6.
    Here is the command I am using: (from http://www.bombich.com/mactips/image.html )
    sudo rsync -xrlptgoEv --progress --delete / /Volumes/Backup
    But the resulted clone won't boot at all (blue screen) What am I doing wrong ?
    Should I add something to the command line ?
    Also, do you know which folders I should exclude from the backup ?
    Thanks for your answers

    Did you Bless the System Folder after the Clone?
    sudo bless --folder "/Volumes/Clone of Macintosh HD/System/Library/CoreServices"
    I use the following rsync options:
    /usr/local/bin/rsync -aNHAXv --one-file-system --fileflags --force-change --delete
    --exclude='.Spotlight-V100' --exclude='/.fseventsd' --exclude='/Volumes/*'
    --exclude='/private/var/vm/*' --exclude='/private/tmp/*'
    --human-readable --stats --progress "$source" "$destination"
    You may need to compile rsync 3.0.6 as follows (see: also http://discussions.apple.com/message.jspa?messageID=10383609#10383609 )
    Follow these instructions in Terminal on both the client and server to
    download and compile rsync 3.0.?:
    Download and unarchive rsync and its patches
    Move patches directory to rsync-3.0.?
    cd rsync-3.0.?
    Apply patches relevant to preserving Mac OS X metadata
    patch -p1 <patches/fileflags.diff
    patch -p1 <patches/crtimes.diff
    Configure, make, install
    (note: creation times are not preserved in x64, so…)
    ./prepare-source
    CFLAGS=-m32 CPPFLAGS=-m32 CCASFLAGS=-m32 ./configure
    CFLAGS=-m32 CPPFLAGS=-m32 CCASFLAGS=-m32 make
    sudo make install
    Verify your installation
    rsync --version
    By default, rsync will be installed in /usr/local/bin. If that isn't
    in your path, you will need to call your new version of rsync by its
    absolute path (/usr/local/bin/rsync).
    Also, be aware that rsync 3.0.6 does properly not handle the metadata for the new HFS+ filesystem compression.
    Sub-test: creation time ... ok
    Verifying: hfs-compression ...
    Sub-test: decmpfs xattr ... not preserved
    Sub-test: UF_COMPRESSED flag ... not set
    Sub-test: file contents ... match
    Sub-test: creation time ... ok
    Sub-test: modification time ... ok
    Sub-test: hard link inode ... ok
    Sub-test: hard link decmpfs xattr ... not preserved
    Sub-test: hard link UF_COMPRESSED flag ... not set
    Sub-test: hard link modification time ... ok
    ok
    Verifying: hfs-compression_large ...
    Sub-test: decmpfs xattr ... not preserved
    Sub-test: UF_COMPRESSED flag ... not set
    Sub-test: file contents ... match
    Sub-test: creation time ... ok
    Sub-test: modification time ... ok
    Sub-test: hard link inode ... ok
    Sub-test: hard link decmpfs xattr ... not preserved
    Sub-test: hard link UF_COMPRESSED flag ... not set
    Sub-test: hard link modification time ... ok

  • I want to upgrade to snow leopard from 10.5.8. Im hesitant to proceed because I'm running iPhoto 7 and word 2004. I want to be sure these programs will still run and I won't lose my photos or the events I have ordered them by. Should i makea clone o

    I want to upgrade to snow leopard from 10.5.8. Im hesitant to proceed because I'm running iPhoto 7 and word 2004. I want to be sure these programs will still run and I won't lose my photos or the events I have ordered them by. Should i make a partition on my new Iomega external and clone it just in case? I'm running time machine and backing up all the time onto an old LaCie, and right now I have a copy of my iPhoto library on new Iomega, which I recopy every couple of weeks. I got the computer new several years ago and it came with iLife and 10.4 OS I think.

    Word 2004 is almost 10 years old, you will not be able to upgrade beyond Snow Leopard with it. IMHO you have gotten your money's worth out of the application and need to upgrade to Office for Mac 2011, this will work just fine and read your old files just fine too. What will not run beyond SL are all PowerPC (PPC) apps such as Word 2004. You will need to update, upgrade or replace any PPC based apps you want to use. I would recommend taking a little time and check for updates to each of your apps. Then open System Profiler (Applications - Utilities - System Profiler) click the Applications link on the left and then look for any PPC based apps, those are the ones that will not run. You can upgrade to SL just fine with the apps you currently have however if you want to go beyond SL (it's already 2 generations behind) you will need to update or upgrade your apps. You can take your time doing it but eventually you're going to have to begin

  • Can I continue using Carbon Copy Cloner after upgrading to Snow Leopard?

    Hi the last time that I backed up my Mac Pro to my external hard drive using Carbon Copy was when I was on Leopard. I recently upgraded to Snow Leopard, can I continue using Carbon Copy Cloner on Snow Leopard or do i have to format the external Drive? Thanks

    For compatibility make sure you have the latest version (3.3)
    http://forums.bombich.com/viewtopic.php?t=14836

  • Yosemite on internal HD and boot Snow Leopard from external HD clone

    Hey Everyone,
    I recently cloned my Snow Leopard 10.6.8 internal HD to an external FW800 HD which I can boot off. I have backup of everything, both Time Machine and straight backups.
    I am thinking of upgrading to Yosemite and am wondering will I still be able to boot into Snow Leopard from the Clone?
    I had heard somewhere that Yosemite makes some changes to the logic board which makes it troublesome but I am not up to scratch on this stuff.
    My System is an iMac 2011, identifier 12,1 with 2.5GHz i5 and 4Gb Ram(soon to be upgraded to 16Gb)
    Many thanks in advance
    J

    Hello. I have a similar question. I recently purchased a new iMac (21.5-inch, Late 2013, 3.1 GHz Intel Core i7, 16 GB 1600 MHz DDR3) running OS X 10.10.2 Yosemite.
    My issue: I have an external drive that I partitioned into two partitions, one is for all my music, pictures and videos. The other partition drive is Snow Leopard 10.6.3.
    On my old iMAc (still set up and using it) which is a 2007 machine and running Mt. Lion, I was able to select which drive to start from, between Snow Leopard and Mt. Lion.
    This allowed me to keep playing Sid Meier's Civilization III (the last version where you can build a palace).
    Anyway, on the new iMac, when I choose the Snow Leopard disk as startup, and it reboots, I get a gray screen with the apple on it, and nothing happens.
    Is there something else I need to do? Any idea why this does not work as easily as it did on the old machine?
    Thanks.

  • Am using Macbook pro mid 2010 running on OSX 10.9.5. It does not read my old Seagate back up plus ITB ext hard disk which opens and works on snow leopard. The back ups were made on snow leopard and mountain lion. How do I make it work on Mavericks?

    I have been making back ups on a Seagate Back up plus drive on a macbook pro running on Mountain lion. Sadly the mac was stolen and all I had was the seagate back up. I tried opening it on my old iMac running on snow leopard and after several visits to this forum managed to open it. The data was safe and sound. Now I have received a hand me down macbook pro which runs on osx 10.9.5. I'm assuming there is a compatability issue as the drive does not come on at all when I hook it up to the usb port. I checked the seagate drive once again on the imac and its light came on on that system. Then I suspected there may be a problem with this macbook pro usb port. But it seemed to work fine when i hooked my camera cord into it. Is it that I must reinstall mavericks. In which case how do I back up before reformatting or reinstalling. BTW I did the command+ R thingy and repaired my internal Hard disc which was showing errors. What do I do next, your help is most appreciated if you have had a similar problem.

    Your 2010 MBP would be able to handle Yosemite, but I would strongly suggest that you get the current problem sorted out before trying to upgrade to Yosemite. I'd also recommend another backup that isn't created by Time Machine if you are thinking of upgrading. SuperDuper and CarbonCopyCloner can make bootable clones of hard drives. If you clone your existing system to a fresh external drive, you would be able to boot from that drive and recover quickly in the event that your Yosemite upgrade didn't work out. Time Machine backups are not 100% reliable.
    It's possible that, if your internal HD is the one that shipped with your MBP in 2010, it may be failing. If it keeps needing repairs, that is probably a sign that it is approaching the end of its useful life.
    Have you run Disk Utility's Repair tool on the external drive as well?
    I mentioned the hub because some people have reported here that attaching their USB 3 drives through a USB 2 hub solved some disconnection problems. A good-quality powered USB 2 hub won't cost much.
    My most recent brush with random disconnections involved a nice new OWC drive enclosure. I used the cable that came with the drive, but the drive kept disconnecting. Using a different cable solved the problem. You wouldn't expect that what appeared to be a high quality cable would be a problem straight out of the box, but it was.

  • Time Machine and Snow Leopard installation problem

    I'm trying to install Snow Leopard, but keep getting an error saying that my hard drive is used for time machin back ups. I have unplugged my external device, turned off time machine, yet this keeps happening. What am I doing wrong? I have been able to install Leopard on the computers that I haven't used time machine.

    BusyChris18 wrote:
    1) Do I have to do anything special with Time Machine BEFORE I install SL? I have been doing regular backups with TM.
    Do a "final" backup and turn TM off.
    2) should Time machine disc be off/disconnected when I do the install?
    It's safest to eject and disconnect it, "just in case."
    3) After I reconnect TM disc after SL install, do I have to "migrate" stuff from TM? OR will it just do a new backup and work like normal from that point forward.
    If you do the normal install, there's no migration needed. 99.9 % of everything will be fine. In some rare cases of 3rd-party apps putting things in unusual places, there may be a problem, and you may need to re-enter some 3rd-party app purchase codes.
    If you erase the drive, then install SL, then yes, of course, you'll have to transfer your data. There should be no reason to do that, but some folks seem to do it out of habit. If you do that, when your Mac boots up again, you can transfer your data from the TM backups. And if you do that, I'd strongly recommend making a separate full backup on a second external drive, again "just in case," preferably a "bootable clone." CarbonCopyCloner and SuperDuper are the most common. (There was a post here just last week where someone did this, the restore got to 99%, then BAM! the TM disk failed.)
    TM backups should just continue normally, although there will almost certainly be a long "Calculating Changes" phase (used to be called "Preparing"). And they've added a progress bar, which doesn't seem to be particularly accurate.
    However, it may try a new, full backup. If it does, cancel the backup and do a Restart. That may reset whatever confused it. If not, there's nothing you can do to prevent it.
    4) Will I be able to access files that were backuped when I have just Leopard?
    Yes.

  • How do I set up my Snow Leopard from Leopard easily w

    Hi,
    Can anyone help? I am running Leopard on my iMac and have just been sent a Snow Leopard Disc from Apple which I would like to now install.  I don't have an external HD but do have lots of photo's in iphoto, tracks in itunes and files and folders I don't want to lose. 
    When I install Snow Lopard, will all my pics, tracks, files and folders still be where they were before?  Will it just have all the new features set up and everything else will stay the same?
    Help is very much appreciated.
    Thanks
    Adam

    Adam Mac User wrote:
    ...  I don't have an external HD but do have lots of photo's in iphoto, tracks in itunes and files and folders I don't want to lose. ...
    BEFORE...  attempting any Major Upgrade... get yourself an External Hard Drive... and create a Bootable Clone Backup of your current Hard Drive...
    By far the easiest way to make such a Backup, is to use something like
    SuperDuper  http://www.shirt-pocket.com/
    or CCC  http://www.bombich.com/
    That way, should anything untoward happen during the Upgrade,
    You will NOT LOSE ANYTHING.
    (Get an EHD that is at least equal to your current Drive...)

  • How to Downgrade to Snow Leopard from Retail disk

    Hi there
    We have a new iMac at work bought through Apple's refurb site. It is running the latest version of Lion with all firmware updates, etc. It is replacing a G5 running Tiger.
    The problem is this – it is supposed to be running Adobe CS5, but also CS4 (and Office would be handly also)
    We have other macs here, some running Leopard, some Snow Leopard, but the Adobe apps are not happy at all in Lion, and InDesign CS4 crashes all the time and won't even print without jumping through a million hoops (obviously the Office 2004 app won't run at all).
    Due to the level of issues we are having with Lion (and the reliability of the all the software under Snow Leopard) I am looking to downgrade to Snow Leopard.
    I have a full retail version of Snow Leopard (10.6.3), but the Lion system won't boot from the disk, it just gets to the grey screen, and beeps three times. I presume this means that there isn't the required drivers on the disk to run the hardware, or there's a firmware update that doesn't allow installation.
    Am i totally stuck with this OS? I was looking to install Snow Leopard on a partiton, but when i run the install disk from the Lion desktop, it reports that I can't run it because 'I have Install Mac OS X 23.1.1.'
    I would really like to just have Snow Leopard on my iMac, or failing that, Lion on a small partition, and Snow Leopard and all the programs on the larger partition that I would boot from.
    Any ideas how I can get this done? Adobe CS suite is just rubbish on Lion macs, and runs worse than on my old Tiger mac.
    Thanks in advance,
    M.

    Mac_fool wrote:
    oh right - so clone Mac B onto Mac A HD in taget disk mode using SuperDuper (or Carbon Copy Cloner), then i'll be able to boot Mac A in SL.
    I understand that Mac A wouldn't boot, I was going to make Mac A's SL partition the start-up partition for Mac B, and then try and install OS updates to 10.6.8 from Mac B. Once updates are installed - change Mac B's startup disk back, and then surely Mac A would be able to boot all on it's own...
    I'm not sure if this would work in Target Disk Mode, but if you succeed in cloning Mac B to Mac A, you may be able to apply the Combo 10.6.8 update to Mac A while booting from Mac B. The key is that the Combo updater may be able to customize the Snow Leopard installation for the hardware it's actually being applied to. Unless I missed it, we don't really know which iMac you have since it's a refurb. According to Mactracker, only the Late 2011 21.5" comes only with Lion and might not accept Snow Leopard at all. At the same time, it has the same Model Identifier as the Mid 2011, which came with 10.6.6 or 10.6.7 so it might work.
    If at that point Mac A does boot in Snow Leopard, I'd advise running the 10.6.8 Combo updater again while booting from Mac A just to be safe.

Maybe you are looking for