System powers off during boot and I have to repair

Hello,
I am having a niggling problem with a Lenovo 3000 n200 with both Vista and Windows 7
1. close lid, system goes into standby
2. After a couple of hours system powers off ( power cable is in)
3. Power on, system starts booting and powers off, turn power on again and problem repeats indefinitely
4 To overcome problem I select repair and recovery, this sometimes powers off once or twice too, but eventually system boots, repairs and works fine.
I have rebuilt system several times and tried 3 different hard disks.
Problem occurs with both 3.03 & 3.05 firmwares
thanks for your help,
Taggn8tor
Solved!
Go to Solution.

Does this still happen when the battery is removed and is on PSU only, if it does then I have bad news for all you guys, the laptop will require a new motherboard and unless you have an extended warranty then this could be an expensive repair.
Apparently Lenovo call this fault a "Boot on cold issue" and seems to be a common problem with the N series which are over a year old. I personally think it's a single part failure on the motherboard or manufacturing fault.
To find the part number for the motherboard remove the RAM and under there will be the part number for the motherboard which will look something like 1r7694, 43n7652, 41r7695, 43n7654 etc.
The problem you have here is will a replacement motherboard after a year have the same fault?
I would also look up the Consumer Protection act and check out the part which says Fit for Purpose.

Similar Messages

TS3694 So I have an iphone4g in recovery mode. followed all the steps to the T. Error pops up in itunes 1602. Prior it was powered off during erase all content and settings mode waiting to reboot

So I have an iphone4g in recovery mode. Followed all the steps to the T. Error pops up in itunes 1602. Prior it was powered off during erase all content and settings mode while waiting to reboot. Now its back to the apple logo. Any ideas if powering it off during the erase all content damaged the software?

You should really read the manual.
"How do you restore from backup? "
Restore. When given the choice, choose to use backup.
"And how can I check to see if the pics and videos are on my computer somewhere first??"
They would only be where you put them. What program did you use to import them? Pics/vids taken with ipod are not part of the sync process at all. You should be importing them just as you would with any digital camera.
If you did not import them, then they are not on your computer.

Aspire One D255 monitor shuts off during boot

Every time I boot, immediately after the kernel lauches init, my screen powers off. About 15 seconds later, it comes back on.
The delay before coming back on seems to be independent of the init process. If I speed init up, by the time it comes back on it's waiting at the login prompt. If I slow it down, it comes back on while init is still running.
I tried adding an echo -e -n '\033[13]' to my init scripts in an effort to unblank the display, but it doesn't help.
This happens both booting of the install image and after installation. It makes it extremely hard to figure out what's going on during startup.
Has anyone seen this before?

I have a similar issue with my aspire one, but the display is not turning off, it is actually the backlight turning off during boot. I use fbsplash with a dark theme but a bright progress bar. During boot, it appears as if the screen has turned off, but looking closely, I can still see the progress bar.
I have tried several different methods of keeping the backlight on to no avail.
Personally I am thinking it is monitor signal detection during a monitor mode reset during boot, ie from console resolution switching to KMS resolution. Most monitors lose signal detection when changing mode (in my experience). Some display a "No Signal" message of some sort, some briefly turn off until signal is detected again, and in the Aspire One case, the backlight turns off. Put it down to monitor manufacturers built in power saving "features".
Tha same thing happens when I boot windows.
Of course, if anyone does come up with a solution, I am eagerly listening!
Cheers.

Build-in webcam issue: how to turn it off during boot-up?

Hi,
I have a laptop - Asus K52J & x86_64 - with a built-in webcam. During boot-up, the webcam turns on in - rough guess - 50% of the time. I don't find any obvious pattern when/why the webcam turns on.
Searching this forum/internet doesn't give me a good answer...
1/ I prefer a solution where the webcam is turned off on boot and where I can turn it on when necessary.
2/ I can afford to disable the webcam when running linux.
3/ Disabling in BIOS (often given solution) is not an option.
For 1/, the only solution I got was running following and closing mplayer window. This turns off the webcam, but this is not an efficient manner. Is there another software-based work-around?
mplayer tv:// -tv driver=v4l2:device=/dev/video0
For 2/ I hear blacklisting the module is the solution. But how do I find the correct module?
lsmod
gives a whole list (pastebin).
Is it videodev and/or v4l2_compat_ioctl32? How can I be sure? Any advice on this for other users with other laptops?
Thanks for any help on advance!
Kind regards,
davidbe

Your webcam uses the uvcvideo module so blacklist that one in /etc/rc.conf.

[SOLVED] USB Harddrive via fstab turned off during Boot - Error

Hello^^
I'm trying to mount my external USB Drive.
I put the following line in fstab:
/dev/sdb1 /media/Musik ext4 noauto,user,default 0 1
I only want to start the Harddive occasionally.
The problem is, when the drive is completly turned off during boot I get the following error:
No such file or directory while trying to open /dev/sdb1
Possibly non existend device?
I thought that the noauto Option should prevent fstab from mounting the hdd???
regards
cl10k
PS: Manual mounting works without any problems...
Last edited by cl10k (2011-03-20 22:49:43)

Let me give you a hand then. The following I have in my /etc/udev/rules.d/11-media-by-label-auto-mount.rules, and what it does is:
-- pick the name of a drive,
-- create a dedicated /media/mountpoint name (certainly, "mountpoint" is replaced by the name of your drive),
-- mount the drive on boot,
-- unmount the drive on shutdown and delete the /media/mountpoint.
KERNEL!="sd[a-z][0-9]", GOTO="media_by_label_auto_mount_end"
# Import FS infos
IMPORT{program}="/sbin/blkid -o udev -p %N"
# Get a label if present, otherwise specify one
ENV{ID_FS_LABEL}!="", ENV{dir_name}="%E{ID_FS_LABEL}"
ENV{ID_FS_LABEL}=="", ENV{dir_name}="usbhd-%k"
# Global mount options
ACTION=="add", ENV{mount_options}="relatime"
# Filesystem-specific mount options
ACTION=="add", ENV{ID_FS_TYPE}=="vfat|ntfs", ENV{mount_options}="$env{mount_options},utf8,gid=100,umask=002"
# Mount the device
ACTION=="add", RUN+="/bin/mkdir -p /media/%E{dir_name}", RUN+="/bin/mount -o $env{mount_options} /dev/%k /media/%E{dir_name}"
# Clean up after removal
ACTION=="remove", ENV{dir_name}!="", RUN+="/bin/umount -l /media/%E{dir_name}", RUN+="/bin/rmdir /media/%E{dir_name}"
# Exit
LABEL="media_by_label_auto_mount_end"
Plenty of handy examples you can find in /lib/udev/rules.d/ and modify them so they meet you needs. I hope it clarifies the matter a bit.
Last edited by bohoomil (2011-03-19 16:57:36)

Equium A300D suddenly powers off during use

I just got an Equium A300D about 3wks ago and it suddenly powers off during use.
What can be caused this?
Though it doesn't do it frequently but am still very concerned.

Sounds like its overheating. My previous laptop did a similar thing.
Is the laptop used in a dusty environment? Perhaps there is dust buildup in the heatsink.
When you use the laptop, are the vents covered by other objects?
Otherwise if its not an overheating issue, and you are using the original Toshiba AC Adapter, bring the laptop to an Authorized Service Center for repair.

HT201413 ipod powers off during restore

Cannot get my ipod touch to restore. It powers off during restoration. Is this normal?

Hi tckm,
A restart is normal, as in step 4 here:
iTunes: Restoring iOS software
http://support.apple.com/kb/ht1414
However, if the device is powering off and staying off, this article is probably the way to go:
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808
I hope this helps!
- Ari

Why am I getting this error message: Unable to write the email to the mailbox. Make sure the file system allows you write privileges, and you have enough disk s

I am getting this error message, just starting today: Unable to write the email to the mailbox. Make sure the file system allows you write privileges, and you have enough disk space to copy the mailbox. I have tried several solutions (cleaning out my inbox, compacting folders, rebooting, checking through the webmail side), all to no avail, Can anyone help?

which os do you have?

Was attempting to use my itouch 4 th generation to play my itunes through my receiver the 1 st song started and stoped after a few seconds so I powered off the itouch and the clockwise circle has been spinning fro the past 20 min ...any thoughts or ideas?

I was attempting to play itunes through my receiver with my itouch 4 the 1 st song started and stopped a few seconds later so I powered off my itouch and the clockwise circle has ben spinning for close to 1/2 hour any suggestions as how to get the thing back to normal...............

I was attempting to play itunes through my receiver with my itouch 4 the 1 st song started and stopped a few seconds later so I powered off my itouch and the clockwise circle has ben spinning for close to 1/2 hour any suggestions as how to get the thing back to normal...............

Why does Mobile Data notification keep coming up saying 'Mobile Data is turned off for "Numbers" and I have to click on OK to get rid of it? I KNOW it's turned off for that program because that is what I want it to be set at. What I DON'T want is to have

Why does Mobile Data notification keep coming up saying 'Mobile Data is turned off for "Numbers" and I have to click on OK to get rid of it? I KNOW it's turned off for that program because that is what I want it to be set at. What I DON'T want is to have to click on OK EVERY TIME I open the program when I'm away from wifi.

That is how it works in general, not just for Numbers. It irritates me on other apps at times, although I can see an argument that if it didn't do that then people would complain about missing functionality after they forgot they had turned data off for an app. At any rate, this is a user to user support forum and we can't do anything about it. If you want to make a suggestion to Apple, following is a place to do that: http://www.apple.com/feedback/

My airport turns off by itself and I have to restart the computer for it to work again and it only turns off again. I have Mac OS X version 10.6.8. What can I do to solve this problem?

My airport turns off by itself and I have to restart the computer for it to work again and it only turns off again. I have Mac OS X version 10.6.8. What can I do to solve this problem?

Usually the HDD is the frist place to look. Use the original install disk and start up the MBP with the C key down. Go through the installation process until you see on the display a menu bar on top.
Click on UTILITIES.
From the drop down menu select Disk Utility.
Open Disk Utility>First Aid and run Verify and Repair.
What are the results?
Also look at these articles:
https://discussions.apple.com/docs/DOC-3521
http://www.thesafemac.com/mpg/
Ciao.

Error: Unable to write the email to the mailbox. Make sure the file system allows you write privileges, and you have enough disk space to copy the mailbox.

when trying to download new messages into Thunderbird, I keep getting the error message:
Unable to write the email to the mailbox. Make sure the file system allows you write privileges, and you have enough disk space to copy the mailbox.
what does this mean and how do I correct it???
thanks

I have this problem too, but my Inbox is empty. There are 125 emails waiting on the server, including one i just sent from another address.
The site you recommended is "having difficulties".
May 4
I have now accessed the KB article above. None of the recommended actions made a difference. I deleted about half the 130 emails awaiting download from web-mail, but still got the same error. I can't clean out the inbox because I can't download emails yo it :-( I have 3 other addresses operating under the same server satisfactorily.

My ipod is freezing during booting and my pc doesnt recognize it

Hi
I did a restore ipod from my ipod and after it completed it , my ipod cant boot. It freezes during booting and my computer doesnt recognize it when i plug it.
Is there anything I can do ?
Thanks.

http://support.apple.com/kb/ht1808

TV screen frozen on Apple logo after pressing select button on remote. Have powered off Apple TV and router.

TV screen is frozen after pressing select button on remote. Have powered off both Apple TV and router. Menu does not come up. All that is on TV screen is Apple logo with black screen.

Welcome to the Apple Community.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Devices list, and then click Restore.
(You may already have a micro USB cable if you have a camera or other digital device)

RV180 (wired only) problems with firmware 1.0.4.14, fails to boot correctly + LAN ports power off during boot (downgrading to 1.0.3.10 = fine again).

Hi All,
A few months ago when 1.0.4.14 was released I was quick to update to this version from 1.0.3.10 but very quickly ran into issues.
Bit of background info... I am not doing anything complex with this box, basic IP4 network over all LAN ports, no VLANs, firewall enabled and allowing 2 port access rules to a static IP address. Any static IPs are assigned manual at host level but all other devices receive DHCP IP addresses. I don’t host VPN on this RV180 but I do with another. Routing VPN has no issues. WAN is connected to another switch provided by my ISP who provides DHCP IP Address with their DNS etc. Only LAN ports 1 and 2 are connected, port 1 to my Wireless AP (AP mode passing all requests to the RV180, DHCP etc.), port 2 connects to a 8 port Smart Switch (but all 'Smart' features are currently not in use, so basic switching only). All other settings on the RV180 are on recommended defaults.
Everything is working fine on 1.0.3.10 but I have all kinds of issues after updating to 1.0.4.14. Here are the actions and experiences I had...
1) Backup my RV180 config to txt file.
2) Navigate to the firmware upgrade page and follow steps to complete the upgrade process from 1.0.3.10 to 1.0.4.14. *router does the normal process of upgrading*
3) RV180 reboots to complete but doesn’t come back up even after waiting 5-10 mins. LAN ports enable during boot up (link lights on) but after about 2mins turn off (no link lights). WAN light is on alongside the Power Light.
4) Power cycle even with rest... Same results.
5) Reset the RV180 to default settings. I can sometimes get the unit to boot up and the LAN remains active and powered up. The web UI is VERY slow compared with 1.0.3.10. Internet sometimes works and sometimes doesn't (I would expect it all work without issue on default settings).
6) I repeat this a few times, various resets, powered off waiting periods, etc. but I always have issues. I did manage to get some log file information and the Kernel appears in the Alert, Error and also the Warning logs (please see attached files).
7) I gave up at this point. No major issues like this reported on the internet from a few google searches etc. So I then reset to defaults (1.0.4.14), downgrade to 1.0.3.10 and finally reset to defaults again + restore backup config settings (with some manual changes).
The router has remained like this and seem to be working fine, but I would like any security improvements from 1.0.4.14 firmware on my device.
Anyone able to help, have the same issue or can advise me in any other ways?
I see 1.0.3.10 isn’t displayed as a firmware download on the standard support page for the RV180 now. Only 1.0.2.6 and 1.0.4.14. Do I need to downgrade again to 1.0.2.6 before upgrading to the latest version?
Regards,
~FAZ~

Hi,
I recently bought a RV180 router and immediately I encountered the same problem; practically I am not able to access the web GUI.
The PC is directly connected to the router, nothing else is connected; the TCP/IP configuration is as follows:
PC: 192.168.1.100
RV180: 192.168.1.1
GATEWAY: 192.168.1.1
SUBNET MASK: 255.255.255.0
Once the router is turned on, the power LED flashes fastly, the Ethernet LED is on but after few minutes it disappears and the PC detects a disconnection of the Ethernet cable.
The router is not pingable and, as I said, the web interface is not reachable.
I have tried to power cycle the router, to reset it (pressing the reset button for more than 3 second and for more than one minute), to access the rescue mode and download a new firmware through TFTP, but nothing worked.
Few times, after many boot and reset trials,I was able to access the web interface and in one of these occasions I updated the firmware to 1.0.4.14 but once the router is powered off the problem arises again at the next power on.
I have not tried yet to downgrade to an older firmware version.
Can you suggest any solution? thank you.

System powers off during boot and I have to repair

Similar Messages

Maybe you are looking for