The signal still the same!!!!
I have the linksys wireless-G range expander model WRE54G, I setup every thing correct but the signal still the same no change what should I do to make it expanded
Try this -
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your Expander, wait for 30 seconds and re-connect the power cable...
1. Connect your Expander to a computer, click on the Start button >>> Settings >>> Control Panel >>> Network Connections - Right click on the icon for Local area connection and go to properties- On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button- Select 'Use the following IP address'- Provide IP Address - 192.168.1.5, Subnet Mask - 255.255.255.0...Click on Ok button to Save and Click on "Close" on main Properties window...
2. Now open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.240.
Leave the Username blank & in Password use admin in lower case...It should open your Expander set-up...
3. Once you get to the set-up page you can follow this link to change the Expander Settings...
4. While changing the Expander settings you have to make sure that the Wireless Settings(SSID/Network Name and WEP/WPA Key) are identical on both the devices(Router and Expander)...Also make sure to change the Expander's default IP to match your network and Gateway Address should be your Router's address...ex. Expander's IP Address : 192.168.1.240(assuming your router's default IP Address is 192.168.1.1), Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1...
5. After configuring the Expander you should disconnect it from the Computer and go into Local Area Connection TCP/IP Properties and set it back to Obtain IP Address Automatically...Disconnect the Expander from the computer and power cycle both the devices(Expander and Router)...Your Expander should be configured...
In case if you don't get the Expander set-up just leave it connected to your computer and reset it for 30 seconds and follow Step 2, Step 3, Step 4 & Step 5...
Hope this helps.
Similar Messages
-
I had tried restore my iphone through the icloud several times, the result still the same. Getting my partner contact numbers instead. Connecting to PC, same result also. On/off contact in the icloud, also same result. Difficulttt
I had tried restore my iphone through the icloud several times, the result still the same. Getting my partner contact numbers instead. Connecting to PC, same result also. On/off contact in the icloud, also same result. Difficulttt
-
Fife days App Store not give it to me the verify code, I made I lot email adress, changed and created the new, still the same problem, and this is second iPad that I bought this month, if not help me I don't know how to deal, thank you in advance, maybe I will go to shop and want my money back
Do you have a technical question for us volunteer users?
-
i tried to restore my new ipad in my itunes but it keeping restore it to my old ipad. I did delete also all my backups in the iTunes, still the same problem is showing??? please I need a huge help to have my new iPad as I bought it???
pleeeeeeeeeeeeeeeeeeeeeeese I need an URGENT help,,, someone answer me back
-
Generated Pulse waveform is distorted when I deliver the signal to the output port in the DAQmx
Problem: Generated Pulse waveform is distorted when I deliver the signal to the output port in the DAQmx.
Environment: Windows XP sp3 (32bit), Visual Studio 2010 sp1, NI-Measurement Studio 2010
Device: NI - DAQmx PCI 6251
Analog Input: 1.00MS/s multi-channel (aggregate)
Analog Output: 2 Channel 2.00MS/s
Reference Example: AO_ContGenVoltageWfm_IntClk / AI_ContAcqVoltageSamples_IntClk
Generated Pulse:
1) AO0 = Square Waveform /0-5V / 8KHz / 0.5㎲/sample / sample 50% Duty
2) AO1 = Square Waveform /0-5V / 8KHz / 0.5㎲/sample / (Reverse Image)
Description: I’d like to deliver the waveform stream satisfied with specified constraints to the 2 channel output port in the DAQmx. To verify accuracy of the generated waveform, I did an electrical wiring from the Analog output channel (2 channels) to the Analog Input channel (2 channels) in DAQmx. As a result of this experiment, I could get a result which has signal distortion. Since the waveform has to satisfy with both high frequency (8KHz) and very short moment interval time (△t = 0.5㎲/sample) between samples, I cannot handle some parameters of the function in the referenced VC++ example. Following formulas shows an approach to deliver the generate pulse waveform to output port satisfied with constraints.
Analog Output Channel
Frequency = 8,000 cycles/sec (constraint)
Sample per Buffer = 2,000,000 = 2*106 samples/buffer
Cycles per Buffer = 80,000 cycles/buffer
Sample per Channel = 1,000,000 = 1*106 samples/channel
Sample Rate = Frequency * (Sample per Buffer / Cycle per Buffer)
= 8,000 * (2*106 / 80,000) = 2*106 samples / sec
△t = 1 sec / 2*106 samples / sec
= 0.5 * 10-6 sec/sample (constraint)
Buffer Cycle = Sample Rate / Sample per Channel
= (2*106 samples / sec) / (1*106 samples/channel)
= 2 channel / sec
Analog Input Channel
Sample per Channel = 1,000,000 = 1*106 samples/channel
Sample Rate = 1 MS/s * (2 Channel) = 5 * 105 Samples / Sec
Program Code
AO_ContGenVoltageWfm_IntClk / AI_ContAcqVoltageSamples_IntClk (VC++ Example)
Result: The proposed approach was implemented in the experiment environment (VS2010, MStudio2010). As shown in Figure 1, we could get the unsatisfied result. Although I intended to make a ‘square’ pulse wave, the result looks like ‘trapezoid’ pulse wave (Figure.1). However, there is other result which was undertaken with different parameter condition. It looks like the square shape not the trapezoid shape.
Please let me know what the conditions make the problem of signal distortion. (AO0 = Green line / AO1 = Red line)
[Figure. 1] Frequency 8000 Hz / Cycle per Buffer = 8000 Result
[Figure. 2] Frequency 1000 Hz / Cycle per Buffer = 1000 Result
Questions: Please let me know following questions.
1) Is it possible to deliver the generated pulse wave satisfied with constraints (f= 8KHz), △t = 0.5㎲/sample) to the output port without distortion using PXI 6251?
(Is it possible to solve the problem, if I use the LabView or MAX?)
2) Are there some mistakes in the proposed approach? (H/W or S/W program)
3) What is the meaning of the Cycle per Buffer?, It could effect to the result?Hi Brett Burger,
Thanks for your reply. For your information, I have set the sampling rate as 10000 as for the sound format, I have set the bits per sample as 16 bit, the rate as 11025 and the sound quality as mono. I tried using your method by changing the sampling rate as 8K but still my program encounter the same problem.
I wish to also create a button that is able to generate a preformatted report that contains VI documentation, data the VI returns, and report properties, such as the author, company, and number of pages only when I click on the button. I have created this in my program, but I am not sure why is it not working. Can you help troubleshoot my program. Or do you have any samples to provide me. Hope to hear from you soon.
Many thanks.
Regards,
min
Attachments:
Heart Sounds1.vi 971 KB -
there is a tick on the changed ringtone but when ringing the phone still the old ringtone is ringing.my phone is iphone 4s
ashibobytariq wrote:
Same thing happened to me, m still searching the solution, plz let me kno too if u find any wayout.
If the old ID is yours, and if your current ID was created by editing the details of this old ID (rather than being an entirely new ID), go to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID. Click edit next to the primary email account, change it back to your old email address and save the change. Then edit the name of the account to change it back to your old email address. You can now use your current password to turn off Find My iDevice, even though it prompts you for the password for your old account ID. Then save any photo stream photos that you wish to keep to your camera roll. When finished go to Settings>iCloud, tap Delete Account and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud). Next, go back to https://appleid.apple.com and change your primary email address and iCloud ID name back to the way it was. Now you can go to Settings>iCloud and sign in with your current iCloud ID and password. -
How do i run an external monitor with my macbook and change settings so that when i close the lid the signal to the monitor is not lost and i can continue using the mac with a mouse and a wireless keyboard?
No, nothing will prevent the computer from going to sleep when you close its display except third-party hacks that are designed to do exactly that. I strongly advise against using any of those, as they may interfere with successful entry into clamshell mode (and they carry other downside risks as well). Just wait until the computer is asleep (with its sleep light pulsing), then press any key on the keyboard. It sounds as though your setup is working as it's designed to do.
-
I have a router in my upstairs, main floor of the house. My iMac connects easily to the router, but the printer does not. If I purchase a second Airport, will it strengthen the signal from the router so the printer will connect wirelessly to the network?
I had the printer connected to the iMac by USB , but when I upgraded the iMac to Maverick OS10 my scanner no longer worked, the more I fussed with it the less productive it was. Now the printer no longer is available at all. The computer does not see it.
The message when I turn them on is that the USB is not compatible. I unplugged the USB cable, and would like to connect wirelessly.
Thank you for any hints
Carol HavensIf you have an Apple router now providing your wireless network, you could add another....like an AirPort Express, for example....to "extend" the signal wirelessly and provide more coverage.
This is always a bit tricky, because the AirPort Express would need to be located where it can receive a strong signal from the main AirPort wireless router.
For example, if you need more wireless signal in a bedroom at the end of the house, you would locate the AirPort Express about half way between the main AirPort router and the bedroom.
On a side note......only the print function will work when you connect an All-in-One device to the USB port on an AirPort, so connect the All-in-One using wireless for full functionality. -
How to fix the signal from the microphone to the computer when recording through an interface in logic pro? Every time i record and playback i get poor signal and a lot of fuzz.. how can i fix this problem?
Which model computer?
What operating system? -
Older Airport express won't see the signal from the cable modem.
Older Airport express won't see the signal from the cable modem.
My macbook sees the AP express and I can stream music to it but no internet. If I plug the ethernet cable directly into the macbook I can see the internetAnytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results. -
for five days bought ipione 4s and out of the blue loses the signal on the network and makes it very regularly, I have upgraded to version 5.0.1 if you can help me.
I had the previous model and forced to buy 4s to catch a better signal, the network I have is cosmote and where it is full house is important, I want your helpHi ChrisBell,
my Pixi shows me the missed calls in a list of its own? I don't have many, so maybe I'm missing something. But I agree with your half-ranting to some degree. As a long-time Palm-user (my last phone was a Treo 680, terrible form factor, good UI), I am really disappointed with the standard software on this phone. Memos and Tasks, which AFAIK were there and useful even on the first Newton's, have regressed beyond the point of usefulness now (solution: Toodledo and Done!, at least for now).
But ChrisBell: if you feel up for it, you could start tinkering. Many people love these phones so much they have started developing patches to solve the obvious problems skimmed over by developers. Try looking up "webosquickinstall" and "preware", and you will find over 300 patches and a lot of free software to help you out. I am not a computer wizard myself, but I am not scared of them either, and I have been able to make good use of all these extras made available by the community.
just a thought, might help you out on a few of your half-rants -
I am trying to hook my MacBook Pro to a Sony Bravia TV via DVI to HDMI cable and the TV will not recognize the signal. I have used the same setup with three other TV's, each a different brand with no problem. Any ideas?
Is the TV set to take input from the HDMI connection?
On your computer, if you open the Displays preferences and do not see an Arrangement tab (or there is an Arrangement tab that shows only a single monitor) then there is something physically wrong with your connection. Try clicking Detect Displays just to see if the computer can now sense the presence of the connection. Check your connections.
If you do have an Arrangement tab, and it shows two screens, then click Gather Windows to bring the TV's Displays preferences on to your main screen if the TV is not yet showing an image. Set the proper resolution (probably 720p, 1080i, or 1080p). Set the refresh rate (probably 60Hz) if that preference is shown. You should see a picture at this point. I recommend turning off mirrored displays if it is enabled. -
HT5922 My air play speakers both loose the signal at the same time
I recently started using Airplay with my itunes and internet radio. but the signal to my wifi speakers constantly cuts out. two speakers two different makes cut out at the same time. is it my ATTwirless modem?
I would suggest you to upgrade/reflash the router's firmware.you can download the firmware from www.linksys.com/downloads.
On the linksys setup page,click on the Administration tab to upgrade the firmware.
After upgrading the firmware,reset the router for 35 seconds,power cycle the router and re-configure the router from scratch. -
My id gave been disable but after reset password still come to same issue,the id still disable, kindly help to advice!
Contact itunes support
-
Collect files question. Why are the paths still the same?
So I collected all of my files from a project and the new project points to all of my old paths. So is there a way to collect the files and have the project point to the new files that were collected? Not sure why they would not be connected. Or am I missing something.....Luckily I had a small project now and replacing the footage is not a big deal, but I have a really big project I'm working on now and it will be pretty time consuming in the future when I access the archived file, to replace all of the missing files. Thanks in advance
Stanley Arthur wrote:
I've seen folks belly ache and go on and on about "if you offer this feature, why can't you make it work???", to the point of personal attacks on Adobe support people. To those, I just say "PICK YOUR FREEKIN BATTLES". There are quick and easy workflows that WORK. And that is the point. KEEP WORKING.
So it's just supposed to be understood that this feature flat out doesn't work and we're supposed to be roll over and be elated that we bought a $1000+ package program that touts certain features that in fact don't work? That sounds like the Apple fanboys who still swear by Final Cut Pro X despite it being anything BUT pro. "We don't need Bluray, Steve says so."
I think Adobe either needs to make it work, and work right, or remove the broken feature until they can get it right. What's unreasonable about that? That sounds obvious. If a feature is listed as a function of the program, we, the consumers have a right to expect that feature to work.
That's like telling somone who bought a 4x4 truck to pick his battles and only drive on the interstates in the summer and not venture off road or drive through snow because the four-wheel-drive feature doesn't work... and quit complaining it doesn't work, geez! Keep it on the nice summer highways, buddy. Duh!
This guy has every right in the world to expect his four-wheel-drive to work because it's a listed feature of the truck... heck, it even has a 4x4 button to push inside the car... with options!
At the very least, Adobe needs to make a disclaimer of the like: "use this feature with caution, still in beta.... still. In fact, it flat out doesn't do as the documentation states, but feel free to give it a try if you want. But please don't come fussing to us if it doesn't work; we're tired of hearing the complaints."
Or, just disable the dumb thing till they can figure it out like much inferior Edius easily did and, as much as I hate to say it, FCP7.
Maybe you are looking for
-
I think I have opened the sobig.f virus in my hotmail account and it keeps seding emails to my contacts. How do I stop it, and will it effect any of my other transactions like internet banking/shopping, is it safe To continue using my ipad ?
-
How do i backuup my library and playlists?
I need to restore my computer to factory settings, but I have a lot of music in my library - how do I back that up? I subscribed to ICloud and iMatch (I think), but When I RESTORE my computer, how do I get that back?
-
What is the best way to create a Flash site
Hello Everyone, I am realtively new to flash. I created the splash page of our site in flash but 1st off it takes to long to load as it is. But I would like to create the entire site in Flash. What is the best way to create a Flash site, and are ther
-
I can not get my new iPad 3 to work with iPhoto The sort order is NOT date and NOT by name I have tried to change on iMac to date and then sync But nothing ocuurs on iPhoto - iPad3 How do I get a proper sort order for occasions? Anyone know?
-
It is taking FOREVER to backup my ipod touch 4th g
last night i tried and i started at about 9pm and at 3 am it had barely moved. maybe 5 cm. and so far it's been 2 hrs and maybe 2 cm. what can i do? i am dying a slow death over here. all i want is the new io5. is there ANYTHING that i can do to spee