Time format change after update to 4.0.7577.250 on aastra 6725ip

Hi,
i make an device update on my aastra 6725ip to version 4.0.7577.250.
After that update the time format is changed. I found in the changelog that this should be fixed?!
What todo?
regards,
Frank

Whats the format changed to?
Can you use settings to change the format? Or do factory reset on phone (hold 4 and 6 while booting).
Andrew Morpeth
Lync Server Specialist - Auckland, NZ
Check out my blog

Similar Messages

CONTACT NAMES NOT DISPLAYING & TIME FORMAT CHANGING AFTER SYNC

i live in kuwait and i was just gifted an officially unlocked 3g iphone from new zealand. i upgraded to 2.1. i have 2 problems
1. i have synced my contacts from address book. the format that it is stored in is +965XXXXXX. 965 is the country code for kuwait and all numbers in kuwait are of 7 digits. there is no area code as this is a small country. when someone calls me their name does not appear. only the number appears
2. i have set the time format on the iphone to the 24 hour format but every time i sync with my macbook the time format changes to 12 hour format.

Follow this procedure to get your contacts back (I assume they are on your Mac/PC):
1. Go to Settings, then Mail, Contacts, Calendars
2. Select your account which has the contacts you wish to sync
3. Turn syncing for Contacts to "Off". This will bring up a box telling you your iPhone is turning off Contacts. My iPhone actually hung at this stage, so after several minutes, I performed a hard restart (holding down Home and power buttons for 5 sec.)
4. Exit from Settings
5. Go to Settings, then Mail, Contacts, Calendars
6. Select your account which has the contacts you wish to sync
7. Turn syncing for Contacts to "On". This should restore your contacts
8. Go to Contacts to verify. They initially may not appear or just show up as numbers for a second or two, but then your contacts should appear.

Export to Excel format changed after update to new Office

Post Author: Ceraq
CA Forum: Exporting
I am using the XL export format as an intermediate step to some complex calculations and ties that are not supported in my legacy system. To get what I want I simply used a CR XI report to create a mid way data file and then used a second report to crunch the final numbers from the data file. Its a long painful story as to exactly why I have to do it this way... not my choice.
Prior to the update when I exported more than ~65k lines to an XL format they remained in one sheet. So the second report would grab all the data and go... Now, after the update of office, the report gets split into seperate sheets each of ~65k records long and the second report sees each sheet as a seperate data table! I'm pushing over 1.25 million records into less than 400k in the mid data file so I'm getting about 7 sheets instead of the original 1.
I have a lot of work and time invested in this method so I would like to fix it so it still works in the previous manner... I have tried to export to a different format, but it seems that CR XI cannot export to a format that it can also read in... at least that I have found and not without creating a whole new DB for it to export into (Access). I cannot unroll the new office either as it is already enterprise wide...
Reomendations? Suggestions? Should I simply go get a few cases of Dr. Pepper and tell my wife I wont be home this week and re write everything (no plan on how I'd do that either...)?
Best regards,
Michael

Hi Debbei
I think u have to use microsoft office 2003
Regards Reeha

When creating a new window in safari, using command T, the marker have not activated the search field. It means you have to click there every time. Changed after upgrading to Mavericks. Anyone knows how to change this?

When creating a new window in safari, using command T, the marker have not activated the search field. It means you have to click there every time. Changed after upgrading to Mavericks. Anyone knows how to change this?

Yes, you can do something like that. What you would do is create a button for each image and then hide them. When I do this type of thing I place all of the buttons on a template page and then hide the template.
You can then use JavaScript to copy the icon from any of the hidden buttons to the main button that you've set up to display the image. For example, suppose you set up 10 buttons named b1, b2, b3, ...b10. The code to copy the icon from one of them to the button used to display the image (b0) would be something like this:
// Get the icon from the b3 button
var oIcon = getField("b3").buttonGetIcon();
// Get reference to the b0 button
var f = getField("b0");
// Set the icon of the b0 button to the icon retrieved from the hidden button
f.buttonSetIcon(oIcon);
// Show the b0 button
f.display = display.visible;
This code would go in the Mouse Up event of the smaller button.

Hello, my 1st time here..after updates my mac yosemite my illustrator can't open. It ask me to install "legacy Java SE 6 runtime" it also affecting my dreamweaver and flash rest are fine. Im bought adobe creative suite 6 DWP. thanks

hello, my 1st time here..after updates my mac yosemite my illustrator can't open. It ask me to install "legacy Java SE 6 runtime" it also affecting my dreamweaver and flash rest are fine. Im bought adobe creative suite 6 DWP. thanks

rezala,
You should be able to get round the issue altogether without the legacy version (and its security implications), by following this:
http://oliverdowling.com.au/2014/03/28/java-se-8-on-mac-os-x/
It is even more thoroughly described in this thread, see post #3 on by gator soup:
https://forums.adobe.com/thread/1706469

I am getting run time error 6034 after updating iTunes to new version.Any help?

I am getting run time error 6034 after updating iTunes to new version.Any help?
I tried different ways to resolve it like uninstall/install itunes
I am also getting error message on iTunes helper.exe

Hi isush!
I have an article for you that will help you troubleshoot this issue:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Thanks for coming to the Apple Support Communities!
Cheers,
Braden

Re: Personal Account number changed after update

Personal Account number changed after updating Virtualstore and now I can't login with my current account information. Changed from 35482 to 35555

i have created already an account after reset but then asked for an update. I did it and now asks for username and password :) still says incorrect username/pass

Language change after update to Lightroom 3.2! Help asked!

I use Lightroom from the first version and love to work with it. I always work with the English version of it - for several reasons - even when my Windows XP version is in Dutch.
By upgrading to Lightroom 3.2 I selected the English language. After the update my version of Lightroom 3.2 however was in Dutch. I tried to change that to English following the help file, but that does not work
This unwanted change gives me a lot of trouble now as I normally import my pictures with a filename in the date-number format. But the date format in the Dutch version is day-month-year, as I however want to use - and used for over 50.000 pictures!!! - the year-month-day format. I had no trouble with it in Lightroom 3.0. My trouble began after updating to Lightroom 3.2.
Can anyone help me here, as I cannot import pictures I made in the right format now!!!
Ton Soneveldt

The answers is in this thread: http://forums.adobe.com/message/3042985#3042985.

Time format change from 24 hr format to 12 hr format

Hai all,
The client wishes to enter the time in the 12 hr format.could you please tell me , what are the necessary settings to be done from convertion of 24 hr format to 12 hr format ?
How it can be done at user level and T.Code level?
Please throw some ideas.
Regards,
Suresh.

Hai,
This is for the updation of the past data where they have maintained the time format as 12 hr format.Since while uploading, it is very difficult to change into 24 hr time format and i need to change the settings so that system should take the input as 12 hr format. There is no problem whatever the output shows either 12 hr or 24 hr format.
Please throw some ideas
Regards,
Suresh.

Screen brightness not changing after update to windows 10

Hello, After updating to windows 10, I am no longer able to adjust the screen brightness at all. It is stuck on the brightest setting at all times; which is inconvenient when I am on battery power and need it dimmed. The f2 and f3 buttons are not working to adjust the brightness, and I am unable to change it in power/power plan settings. I attempted to search for a possible missing driver that I had maybe lost upon updating, but there are yet no drivers for my product on the HP website for this purpose. Any help on this matter is extremely appreciated, as it is rather frustrating that I can't change my screen brightness. Thanks.

How about using the snipping tool to create an image of what you do see and posting it here. The snipping tool is what I used to create the image that I posted. What version of Windows 10 is installed? I upgraded to Windows 10 Pro on the Omen 15 and have the Enterprise version on one of my desktop systems. I have not yet used the HOme or Education versions, so I do not yet know which features they lack.

[SOLVED] Time is changed after every reboot

Hello,
my Arch has strange behaviour regarding the system time. I use latest up-to-date arch with KDE. No explicite NTPD running and I don't have it in DAEMONS under rc.conf. The KDE own time & date environment is configured to not automatically change time. In /etc/rc.conf I have HARDWARECLOCK="localtime" and TIMEZONE="America/Chicago". Now from the environment to the problem:
Whenever I shutdown or restart my system, the time will be changed after booting into linux again. After shutdown with correct time using "date -s ..", the BIOS clock is correct. Then, when it actually boots into arch, there will be a delay
of 20-40 seconds for "$ date" (approximatelly the time of the reboot process) and also in the BIOS clock!
After shuting down before going to bed and restarting in the morning, the time will be approximately (or more or less exactly) the time when I shutted down... It should not be related to KDE as I observe the same behaviour when I remove kdm from daemons in rc.conf, hence, booting to console, setting time, restarting into console...
As I have dual boot: this problem is not observable using windows...
It seems like the time is stored somewhere during shutdown process and changed accordingly during reboot...?!?
Any ideas or comments? It's really crazy how annoying a wrong computer clock becomes (all IMs and system stuff is based on it...). :-(
Last edited by ichbinder (2010-10-10 09:11:01)

Thanks for all the quick responses!
Primoz wrote:maybe you should start using ntp or openntpd?
It provides you with time directly from the net.
Well, I tried to use ntp. As I am using KDE, there should already be a synchronisation service active. I can activate synchronisation in System Settings -> Date & Time and it works right after activation. But further on, e.g. after a restart - and hence such a wrong time as described in my first post - it does not correct anything. So it seems like, there is also a problem with this KDE synchronisation. But to state why I'm not using it anymore: it doesn't make much sense to use it as this is just a work around and does not solve the problem that the hardware clock might become wrong (so, e.g. I end up with a wrong clock in windows or so). In general, I just want to have a correct clock without synchronisation before I activate synchronisation.
ewaller wrote:
That seems weird.
When you power up, what happens if, before starting your boot loader, you enter the BIOS set up and check the system time?
Yes, it is. Well, if the hardware clock has been set correctly using e.g. hwclock it will be correct in BIOS before I restart arch. Similar observations for the following case:
- set HW clock correct in BIOS
- start arch ... shutdown arch
- check HW clock in BIOS -> correct
- start arch ... shutdown arch
- check HW clcok in BIOS -> incorrect
ewaller wrote:...
Other thoughts: date -s does not set the BIOS clock, it sets the Linux kernel time. On what do you assert that the BIOS clock is correct at shutdown.
Thanks for the hint! In that case, it seems like the KDE Date & Time settings influence both, hwclock and date.
ewaller wrote:...
Also, once booted into Linux, what does the command hwclock show? This command reads the actual BIOS hardware clock.
Yeah, I used that alot now. So as described, it is also incorrect after a restart. But only after arch has booted again. To sum it up:
Using whatever tools to set the hardware clock and the system clock (KDE's tool, hwclock + date, or BIOS + date), both are correct until I reboot into arch the next time. If I do that, it resets both to a time similar to the last shutdown time.
karol wrote:
This doesn't fix anything, but you can try https://bugs.archlinux.org/task/13684#comment52246 - using UTC instead of localtime.
I never checked if my system clock is running perfect at all times or is /etc/cron.hourly/adjtime correcting it once in a while.
Hm, not to sure what they are doing exactly there and how this might help... :-/
What do you mean with the second part of the sentence? Not sure if /etc/chron.hourly/adjtime is doing anything in my case... How can I check if that cronjob is running?
karol wrote:Have you tried this http://wiki.archlinux.org/index.php/Time#Time_Skew ?
But this is very interesting! I will remove /var/lib/hwclock/adjtime as described in the wiki and see what happens then. Thanks!

Hda and hdb changes after updating

Hello,
i've reinstalled my "main computer" a few weeks ago after using it for a year or so with OpenBSD. The System is an old IBM Server which i got used a year ago.
I've installed archlinux on an SCSI disk which hangs on an onboard-LSI-Controller.
There is also a bit SATA-Disk which hangs on an PCI-addon-SATA-Controller with an SIL chipset.
Yesterday i've updatet my System with pacman -Syu, and shut it down yesterday evening. This morning my system won't boot, fsck said "Bad Superblock" or so on sda3 which contains my / filesystem. After a few tries i found out that sda which was my scsi system disk and sdb which was my "big" sata drive switched the letters, so after changing the letters in the fstab, everything works fine now, but i'm a bit confused, as i had never such an issue after updating before.
Is this perhaps a bug that i should post anywhere? Or have i missed a threat or a news anywhere that announced this behavior?
Thanks a lot!

The advice these days is to use uuids which are unique to each volume to avoid these types of problems. the wiki on fstab tells you how. No idea why you experienced this though.

During export from Discover to Excel, Time Format changes to Number Format

Hi
I have a seconds column which is of number datatype. But in my report, I am converting the number in *0HH:MI:SS* format. For example, I have *4952534 seconds*. So my report is showing *1375:42:14* which is a Time Format. It looks good when I view the data in Discoverer Viewer or Plus. But when I try to export the data to Excel, the time format gets converted to *4952534 seconds*, which is creating problems. So can you suggest on how can I preserve the formatting during export to excel from discoverer.
Thanks
Sachin

Hi,
Excel will not implement the 0HH:MI:SS data format, it just gets the field as a number. You will have to format the field into text using the calculation from my previous post.
Rod West

Date and Time formats change in transfer rules

Hello Experts,
Could someone please help me to fix the following issue with DATE AND TIME format.
I have two info objects zdate with data type DATS (length 8) and ztime with data types TIMS (length 6).
The data in the data source (alalertdb table) is in the format of date dd.mm.yyyy and time in hh:mm:ss.
Now when i am trying to extract the data, the load is failing because the system is taking dd.mm.yyyy length as 10 and hh:mm:ss length as 8. My infoobject
only alows 8 for date and 6 for time.
Do I need to write any routines in the transfer rules? If yes please share the code.
All the inputs are much appreciated.
Thanks in advance.
Regards,
Harish

Hello ALL,
Thanks for your inputs.
Adios, I will try your routine if I am not tru with the formula. Thank you very much for your reply.
Bjorn, Your formula sounds quite simple. can you please eloberate the information.
When I used the formula for the date field its giving me an error with message FORMULA ELEMENT IS NOT ALLOWED HERE.
Formula I used is:
LEFT( 2, < /BIC/ZOOH_DATE> ) & SUBSTRING( < /BIC/ZOOH_DATE>, 3, 2 ) & RIGHT( 4, < /BIC/ZOOH_DATE> )
can you also please let me know what results the formula brings.
Thanks and Regards,
Harish Mulaka

FM 10 xref format changes when updating file

I'm authoring in structured FM 10 using a DITA 1.2 application on Windows 7, but working with FM documents rather than XML files. I was having problems updating cross-references in my existing (structured FM 7.2) files after upgrading to FM 10 -- FM was changing all xref formats to DITA Default Format, which blew away all of my defined formats. So I opened one of the standard structured templates included with FM 10 (DITA_1.2/app/technicalContent/template/topic.template.fm), thinking that I set up my structured application incorrectly.
I know I must be missing something simple, but this is what happens when I create and update a cross-reference:
Using the unmodified structured template and the unmodified DITA 1.2 application that comes with FM 10, add an fm-xref element.
Using the DITA-Cross-Reference dialog box, create the xref (doesn't matter if it's an internal or external xref).
Select See_Title_and_Page xref format. Xref looks fine in the source document.
Select Edit > Update Reference, and select All Cross-References.
When I click Update, FM updates the xref but changes the xref format to DITA Default Format. I can see that the See_Title_and_Page format included in the template uses the <$paratext> building block instead of <$elemtext>, but I can't delete or modify this format and I can't create a new xref format, either, since the DITA Cross-Reference dialog box doesn't give me those options.
However, if I create a new FM book and add this file to it, and then select Edit > Update Book, and select All Cross-References, FM updates the xref and maintains the xref format I chose.
So, why does updating a file remove the selected formats from all xrefs and replace them with DITA Default Format, while updating a book does what I'd expect (and what FM has always done)? And why can't I modify an xref format using the template/DITA 1.2 application that comes with FM10?
Thanks for any assistance.
--Steve

Hi Saurabh,
Thanks for the reply. I guess it's reassuring to know that the automatic reformatting of xrefs by FM isn't due to something I've overlooked. As long as there's a workaround, I'll keep updating xrefs from a book. Not a great workflow, but it won't block our writing for now.
On the other issue: Thanks, I do know how to edit xref formats and import them from a template. My confusion, however, stems from two things:
I can't edit xref formats in the DITA Cross-Reference dialog box, which is all you see if you're using the DITA 1.2 template that ships with FM 10. I can edit the formats from the Cross-Reference dialog box, but I can't figure out how to access that when using Adobe's template. Adding a new xref or selected an existing one just activates the DITA dialog box, which doesn't have an Edit Format option (shouldn't it? wouldn't you want to be able to edit those formats? or do you always have to do that from one of the application files?).
The DITA Default Format won't go away. In my own docs (DITA 1.1 FM files), I can get to the Cross-Reference dialog box and edit xref formats. If I delete the DITA Default Format, save the file, close it, and then reopen it, the unwanted DITA Default Format is back. I can reapply the formats and element defintitions from the template as much as I like, but any time the file is reopened the deleted format reappears. It won't die, and I have no idea where it's coming from (definitely not the template or the EDD, which I've checked and reimported). Is this some odd default behavior of ditafm_app.dll?
Again, thanks for responding.
--Steve

Time format change after update to 4.0.7577.250 on aastra 6725ip

Similar Messages

Maybe you are looking for