Time issue in 7942/7962 phones in UC 500
Hi,
I am having an IP telephony set up with UC 500 with Version 4.2(0).The phones are taking the time from the UC 500 itself.we are having 7942 and 7962 IP Phone models.
The isue is that some of the 7942 and 7962 are showing in correct time and some of them showing correct time.
I checked the Firmware for both (correct and incorect) but are same.I have reset the phones couple of times ..but result is same....
I am attcahing the Sh Telephony service along with this....
Please help for the same.
Thanks in advance....
Nithin Louis.
Any update dears????
Similar Messages
-
when i try to activate itunes on my iphone it continues to say "We're sorry, we are unable to continue with your activation at this time." and now my phone has stuck. what happened?
Hello mzpartia,
I found an article from Apple that specifically outlines how to try and troubleshoot this issue. It's called iPhone: Troubleshooting activation issues found here: http://support.apple.com/kb/ts3424.
Resolution
Perform the following steps if you receive one of the messages above:
Restart the iPhone.
Try another means of reaching the activation server and attempt to activate.
Try connecting to Wi-Fi if you're unable to activate using a cellular data connection.
Try connecting to iTunes if you're unable to activate using Wi-Fi.
Restore the iPhone.
If you receive an alert message when you attempt to activate your iPhone, try to place the iPhone in recovery mode and perform a restore. If you're still unable to complete the setup assistant due to an activation error, contact Applefor assistance.
Take care,
Sterling -
How can I keep apps in the order I prefer? I've rearranged via iTunes but every time I power cycle the phone, the apps go back to their original positions...
Hi kelori617,
If you are having issues organizing the Apps on your iPhone via iTunes, you may want to double-check the steps in the following article and make sure you are syncing any changes to your device:
iTunes 11 for Mac: Sync and organize iOS apps
http://support.apple.com/kb/PH12115
iTunes 11 for Windows: Sync and organize iOS apps
http://support.apple.com/kb/PH12315
If all of the steps are correct and the changes still aren't being retained when you restart your iPhone, you may want to make sure your data is backed up, then try restoring your iPhone to factory settings, restore your data from the backup, then test to see if you can organize your apps via iTunes:
Use iTunes to restore your iOS device to factory settings
http://support.apple.com/kb/HT1414
Regards,
- Brenden -
I live in Egypt, I have this issue with my iphone4 recently, whenever i use the [Set Automatically] option for the Date and Time it Not the ring time, meaning for example now it's 6.20am, and the phone says it's 3.20pm, even when i turn it off and set it to Manually changed, and i set the right time, it still changes like a day after to what it's supposed to be if it was on Automatically Set which is far from right, what am i doing wrong?
There is NO ONE from Apple here. Just user like you assisting other users. Sounds like you carrier is having time sync problems, since the phone gets its time from them.
that being said, on the iPhone, check settings:general:date and time: and see if set automatically is on or off. Also try resetting the phone by holding down the home and power buttons and waiting until the apple appears (ignore the power off slider). -
Time issues? time zone settings appear in two places
If you leave the default "set time and date automatically", you see the time zone support below and you can check it or uncheck. You can then set your time zone there. But if you uncheck the automatic date and time, you get another time zone choice and the default is Cupertino, of course. I wonder if that's the problem with some of these time issues.
I've since unchecked automatic date and time, set my city's time zone, then rechecked automatic. The only weirdness I've seen was with an excel spreadsheet where the time was correctly shown on my mac, but not on the iphone. Unfortunately I don't have that sheet anymore or I'd try again to see if it works now.
Just a thought.I noticed the same thing and did the same thing you did because my time was off by several hours each time I turned the phone on...after it being off overnight. When it was off by only 1 hour I could turn the Auto OFF then 'tap' the timezone (already set to the correct city) and the time would instantly correct itself. Then I'd turn Auto back ON.
Turns out that my time issue was related to having the SIM PIN enabled. Once I disabled that, the time's been correct every day. -
Is anyone else having issues with their I Phone 5 running ios 6.1?
As stated above: Is anyone else having issues with their I Phone 5 running ios 6.1?
I am having issues with the WiFi connection to my AT&T router and voice recognition.
It wont make post to Facebook half of the time. It is lacking the option to post videos to Facebook, only to mail, message, and You Tube. And finally the voice recognition messes up what it types in both Siri and messages.Not having any of those.
-
Good day Friends.
My phone loses signal when I receive calls and people do not listen to me at times.
I bought my phone used by Amazon and I think it was open, because I see that this manipulated by one hand.
Someone I can help.?nessbass wrote:
people do not listen to me at times.
That's not a phone issue, but rather that they simply find you uninteresting.
nessbass wrote:
I bought my phone used by Amazon and I think it was open, because I see that this manipulated by one hand.
Amazon is not an official reseller.
If the device has been opened by anyone other than Apple the warranty is voided. -
I'm also having a music issue. When my phone is attached to the computer (mac running 10.6.8) it looks like my music is there but its gray and I can't play anything. I've tried to delete it and it won't let me but it does not show up on my phone.
By the way, I have tried shutting of the display switching in the power settings. That was basically the only real answer I found anywhere. It didn't work.
-
My iPhone 4S will not sync to iTunes. I've download the newest version of iTunes several times but when plugging my phone in it says "The iPhone cannot be used because it requires iTunes version 10.6.3 or later." HELP!
If you're using Windows try uninstalling iTunes and all of its components as by following this guide exactly: Windows XP or Windows Vista/7, then reinstall the latest version of iTunes. You must follow this guide exactly or it will not be successful. Note: uninstalling iTunes will only remove the application; it will not touch your iTunes library or data.
-
I entered a new calender event using I cloud on my laptop. The enent transfered to my i Phone 5 S but, the start and finish times shown st i cloud on the laptop are different than the times shown on the i phone. How do I sync the times on the i Phone with the times shown on the laptop i cloud calender?
Turn off time zone support on the phone.
-
is it necessary to put in sim card in iphone at the time of restore ? My phone is stolen and i am concerned that if somebody will restore it then i will not be able to find it even using find my phone.
There is no way that you can locate the iphone at all.
The thief can restore it and use it as their own. You will never know or be able to tell what they do with it.
Very sorry. Your iphone is gone.
Report it to the police and change your passwords. -
L2 Roaming issue with Avaya wireless phone on WISM -V6.0.196.0
Hello Friends,
I am facing Layer2 roaming issue with Avaya Wirless phone 3620 which are configured WPA / Pre-shared key auth with a SSID1 and face a cut or delay in the voice.
But when i use Cisco Wireless phones and try to roam between one LWAP to other i dont face a cut or delay in the vocie which are
Configured with 802.1x +CCKM auth .
Then i configured new SSID 3 with 802.1x+CCKM settings for the new Avaya wireless module 3631 , but still face cut and delay while doing Layer 2 roaming.
While i was using these AP in WDS mode i never faced this Layer 2 roaming issue with Avaya wireless phones.
In current WISM all the LWAPs are supporting properly to the Cisco phone and Wirelss laptop clients.
I request you to please let me know how do i proceed further to solve the issue and please let me know if anybugs or incompatibilty for WISM with Avaya wireless phones.
Appreciate your response.
Regards,
KA.Hello ,
Can any body please respond to my above Query.
Thanks,
KA. -
HI Expert !
I m using this code .
LTIME TYPE SY-UZEIT
T1 TYPE SY-UZEIT VALUE 030000,
T2 TYPE SY-UZEIT VALUE 050000,
BUT WHEN I M USING T1 AND T2 in loop ( if statement ),ITS value r
T1 = 082000.
t2 = 131100 .
if t1(6) t2(6 )
ltime (6 ).
then ok . but in this i wont be able to make comparison in if statement
how i can resolve this time issue
i dont want to include timings between 3.00 a.m and 5.00 ,
for this i have used this code but its not updating data for any employee , is this code correct or not.
OPEN DATASET PA_FILE FOR INPUT IN TEXT MODE ENCODING DEFAULT.
DO.
READ DATASET PA_FILE INTO REC.
CLEAR WA_PUNCHES.
IF SY-SUBRC <> 0.
EXIT.
ENDIF.
WRITE: / REC.
if NOT ( WA_SCORE-LTIME GE T1 AND WA_SCORE-LTIME LE T2 ) .
AND
***( WA_SCORE-TERID NE TR3 AND
***WA_SCORE-TERID NE TR4 AND
***WA_SCORE-TERID NE TR5 AND
***WA_SCORE-TERID NE TR6 AND
***WA_SCORE-TERID NE TR7 AND
***WA_SCORE-TERID NE TR8 ) .
WA_SCORE-PERNR = REC+0(8) .
WA_SCORE-LDATE = REC+9(8) .
WA_SCORE-LTIME = REC+18(6) .
WA_SCORE-CANID = REC+25(8) .
WA_SCORE-TERID = REC+34(4) .
APPEND WA_SCORE TO IT_SCORE.
ELSE .
EXIT .
ADD 1 TO COUNT.
ENDIF .
ENDDO.
plz help me . its very imp. program .
thanksHi,
Pass values in quotes
T1 TYPE SY-UZEIT VALUE '030000',
T2 TYPE SY-UZEIT VALUE '050000',
Can you please check once again after making this change in debug mode, values of T1, T2 and LTIME.
ashish -
My MacBook Pro shut off three times yesterday after plugging my phone in but I managed to switch it back on each time. I left it to rest for about 20 hours and then today it Has been working fine all morning. Using indesign and Skype which usually slow it down anyway but it's been fine. Then I plugged my iPhone 4S into it and it just shut off again. But this time it won't switch back on. No idea why this has happened but I hadn't saved my work either. I'd not long plugged the charger in to it but now, it's still plugged in, but the light on it is very dim and is just flashing.
No idea what to do. Please help!You have 10.6 on that machine, I suggest you stick with it for performance, third party hardware and software reasons as long as possible.
Consider 10.8 (not 10.7) when it's released, because 10.7 and 10.8 will require a new investment in software and newer third party hardware as it requires newer drivers the old machines won't have. (forced upgrade because of software, really nice of them)
http://roaringapps.com/apps:table
Far as your Safari problem do these things until it's resolved:
1: Software Update fully under the Apple menu.
2: Check the status of your plug-ins and update (works for all browsers) also install Firefox and see if your problems continue. You should always have at least two browsers on the machine just in case one fails.
https://www.mozilla.org/en-US/plugincheck/
Flash install instructions/problem resolution here if you need it.
How to install Flash, fix problems
3: Install Safari again from Apple's web site
https://www.apple.com/safari/
4: Run through this list of fixes, stopping with #16 and report back before doing #17
Step by Step to fix your Mac -
I put a secondary domain and po at a remote location - running 8.03 on Sles/Oes and moved all of the "local" users to that po.
while everything seems to run ok we have a weird time issue.
Mail into and out of the new mailboxes shows a three and a half hour time difference both in the date column in the groupwise client and in the printed header of the email.
The odd thing is that if I go to the properties of the email - the Creation date and the File date and time are both correct.
I can't see any time issues with the servers (primary or secondary) and especially something that would be 3:30 minutes off
there is a timezone difference between the pri and sec but that's just 1 hour.
Any thoughts?
As a workaround I have had my users add the creation column to see when they actually received the email as our clients have time critical projects.
Thanks
DennisDanita,
Thanks for the reply - Oh how I wish it were that easy - I've checked and double checked the PO object and the domain object - both say US eastern time.
If I send email from a mailbox on the secondary to the primary - everything is correct (a 1 hour time difference - Eastern to Central)
If I send mail from a mailbox on the primary to the secondary - it shows up right away, but says 3:30 minutes later than it should (in Date/Time, but not in Created)
If I send email from a mailbox on the secondary to a GMail account - the header shows the 3:30 offset, but the properties of the mail shows correctly.
I would be happy to send email from that po to anyone that wants to see for themselves.
Other than the PO Object and the DOM object - Where should I be looking for a time difference
and how would it be getting UTC minus 30 minutes - - Is there a special timezone out there for Hy Brasil?
The workstations all get their time settings from "time.windows.com" the windows default.
Thanks for looking into this - I just hope that I can get it figured out because as small of an issue that I think it is (they get their email, it just looks like it gets read before they officially receive it)
but it seems that this office uses the received time to track how long it takes them to do their work.
Dennis
Maybe you are looking for
-
How do I create an e-mail graphic poster that can be sent out?
I need to create an e-mail poster advertisement for a recreation area that will be sent out to shareholders. I need to do this for work. Does anyone have any suggestions on how I would do this? Would I create the web page and then send the web page i
-
How to find out if a transportation/accomodation request has been changed?
Hello all, I need to know if one transportation/accomodation request has been changed after being created. I am using the TRIP standard transaction to plan the travel request without any external agency integration. My problem is that if I change any
-
Iphoto 11-import function is not working!!!!!
just tried to download pics from trip from my camera to computer using iphoto 11....it downloads the pics...when i try to import nothing happens"says photos are being imported to photo library"...but it is not doing it!!!!.....
-
Error when trying to edit in external editor in Lightroom 4
Hi all, need help please with Lightroom 4. I have an external photo editor set up so when I choose "edit in" it goes to that editor, not photoshop. I am getting the following error "Unexpected error performing command: bad argument #1 to 'lower' (st
-
Hi, I have written a function which takes table name dynamically and if column emp_id is null for more than 0 records then 1 is returned else 0 . My problem is when i compile iam getting invalid table name error . Below is my function : create or rep