Trying to generate a signal from two signals (EMG) that I have acquired from my NI USB

I am able to aquire two EMG signals that I am sending into a NI USB-6251 using signal express. However, I would like to generate an additional signal which is based on the two signals I've sent in. For example, I would like to show a signal in real time that takes the two signals and divides one from the other in order to show the percent contribution of each signal.
How would I go about doing this?
Thank you

You should be able to use the Arithmetic Step (Add Step Button under Processing\Analog Signals) to divide the signals and then use that output as the input signal for a DAQmx Generate Step. If you want to just view the divided signals you can display the result of the Arithmetic on the Data View by dragging the output of the Arithmetic Step to the Data View.

Similar Messages

HT1459 I am trying to send my sisters songs to her computer that I have downloaded on my computer? I have all her songs on 1 playlist that she needs to sync to her Ipod Nano?

I am trying to send my sisters songs to her computer that I have downloaded on my computer? I have all her songs on 1 playlist that she needs to sync to her Ipod Nano?

Make sure that yo have the boxed chanced to only sync the checked music. It appears that it is trying to sync ore than those.
You can try unsycing all music and resyncing.

Xrpcc modeler error when trying to generate stub classes from a WSDL

I'm trying to generate JAX-RPC stub classes (both client and server side) from a WSDL in which one of the message parts references a complexType element defined in the <types> section of the WSDL. Here is my little WSDL document:
<?xml version="1.0" encoding="UTF-8"?>
<definitions name="Book_Def"
targetNamespace="myTypes"
xmlns:tns="myTypes"
xmlns:xsd1="myTypes"
xmlns="http://schemas.xmlsoap.org/wsdl/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/">
<types>
<xsd:schema targetNameSpace="myTypes"
xmlns:xsd="http://www.w3.org/2001/XMLSchema">
<xsd:element name="Book" type="xsd1:BookType"/>
<xsd:complexType name="BookType">
<xsd:all>
<xsd:element name="authors" type="xsd:string" maxOccurs="10"/>
<xsd:element name="preface" type="xsd:string"/>
<xsd:element name="price" type="xsd:float"/>
</xsd:all>
</xsd:complexType>
</xsd:schema>
</types>
<message name="runMyPgm">
<part name="book" type="xsd1:Book"/>
</message>
<message name="getPgmResponse">
<part name="result" type="xsd:string"/>
</message>
<portType name="MyPgmIFPortType">
<operation name="runMyPgm">
<input message="tns:runMyPgm"/>
<output message="tns:getPgmResponse"/>
</operation>
</portType>
... Binding stuff
</port>
</service>
</definitions>
I've tried many combinations of defining my complex type and input message and whenever I run xrpcc using this WSDL as input, I get a Error: Modeler error: invalid entity name: Book (in namespace "myTypes"). Sorry if this is a dumb question, but what am I doing wrong in my <types> or <message> definitions to cause this error? I've had some luck generating stubs when the part types are all simple types, but I've not had any luck with getting a <complexType> definition accepted by xrpcc. Thanks in advance for any help you can offer.

Yes you can specify type mapping in configuration file and probably this will solve the problem, but I've never tested this approach. Perhaps I'm not advanced user. Actually the serializerFactory and deserializerFactory are a little vague for me:(

When trying to generate pdf file from firefox 7.0.1 , getting corrupt content error, used to work with previous versions of firefox

We have done toleration testing on firefox version 5 thru 6 and haven't got an issue with our website generating pdf files for our users. One of our users upgraded to firefox version 7.0.1 and they tried to generate a pdf report, now a screen pops up with Corrupted Content Error The page you are trying to view cannot be shown because an error in the data transmission was detected. I recreated this issue on my pc yesterday by installing firefox 7.0.1. Any hints as to what I need to look at would help. Cannot provide the url because it is a secure website for law enforcement. Thanks.

You can turn off compatibility checking, but more and more of the Google Toolbar will not work. Google is no longer supporting the Google Toolbar so you should use the alternatives.
Hi Mark,
See http://kb.mozillazine.org/Using_Google_Toolbar_features_without_toolbars
If you have an aspect that is not covered, indicate what that is; otherwise, expect you to be fully functional within 1-2 weeks.
<br><small>Please mark "Solved" one answer that will best help others with a similar problem -- hope this was it.</small>

HT2534 I have already created an Apple ID. I tried to sign in on iTunes, but it said that i have not yet used this ID on iTunes yet. It then directed me to the billing page. There was no option "none" for the credit card payment. It won't let me continue.

I have already created an Apple ID. I tried to sign in on iTunes, but it said I have not yet used this ID with iTunes. It then directed me to the billing page. There was no option "none" for the credit card payment. It will not let me continue without entering one in.

- Add a credit card or other payment method like redeeming an iTunes gift card.
- Create a NEW account using these instructions. Make sure you follow the instructions. Many do not and if you do not you will not get the None option. You must use an email address that you have not used with Apple before.
Creating an iTunes Store, App Store, iBookstore, and Mac App Store account without a credit card

Need some help trying to generate thumbnail images from large Jpegs

Hello,
I have some ActionScript 3.0 code, created with Flex that
will load a large JPEG image (say 3000x2000 pixels) that I'm trying
to create a 100 pixel thumbnail. I have the code working where I
generate the thumbnail, but it's not maintaining the aspect ratio
of the original image. It's making it square, filling in white for
the part that doesn't fit.
I've tried just setting the height or width of the new
image, but that doesnt render well, either.
To see what I'm talking about, I made a screen shot, showing
the before image, and the rendered as thumbnail image:
http://www.flickr.com/photos/taude/533544558/.
Now, there's a few things important to note. I'm saving the
thumbnail off as a JPEG. As you can see in my sample application,
the original renders fine with the proper aspect ratio, it's when
I'm copying the bytes off the bitmapdata object, where I need to
specify a width and height, that the trouble starts. I've also
tried using .contentHeight and .contentWidth and some division to
manually specify a new bitmapdatasize, but these values seem to
always have NaN.
private function makeThumbnail():void{
// create a thumbnail of 100x100 pixels of a large file
// What I want to create is a a thumbnail with the longest
size of the aspect
// ratio to be 100 pixels.
var img:Image = new Image();
//Add this event listener because we cant copy the
BitmapData from an
/// image until it is loaded.
img.addEventListener(FlexEvent.UPDATE_COMPLETE,
imageLoaded);
img.width=100;
img.height=100;
img.scaleContent=true;
img.visible = true;
// This is the image we want to make a thumbnail of.
img.load("file:///C:/T5.jpg");
img.id = "testImage";
this.addChildAt(img, 0);
private function imageLoaded(event:Event):void
// Grab the bitmap image from the Input Image and
var bmd:BitmapData =
getBitmapDataFromUIComponent(UIComponent(event.target));
//Render the new thumbnail in the UI to see what it looks
theImage.source = new Bitmap(bmd); //new Bitmap(bmd);
public static function
getBitmapDataFromUIComponent(component:UIComponent):BitmapData
var bmd:BitmapData = new
BitmapData(component.width,component.height );
bmd.draw(component);
return bmd;

Dev is 10gR2 and Prod is earlier version of Oracle, 10gR1.
The schema (or table(s)) export file created by Oracle Database Control in Oracle 10gR2 is not importable into 10gR1, by default.
Workaround.
Use the Schema (table(s) export wizard of in the Maintenance section
of the Oracle Database Control in ver 10R2,
but when you get to the end of the wizard (I recall Step 5),
show the data pump export source PL/SQL code, cut and past to editor,
and find the variable where you can set the Oracle database version
to your prod database version,
then run the script from the SQL Plus prompt in 10gR2 dev,
and this creates an Oracle 10gR1 compatible data export file.
Then go to Prod and run the schema (table(s)) import data wizard,
and import the export file. You will have to option to move the data
to another schema or tablespace if required.
Just to not run into troubles, I use the same schema and tablespace name
in both dev and prod.
the variable you must modify in the 10gR2 datapump export script looks like
h1 := dbms_datapump.open (operation => 'EXPORT', job_mode => 'SCHEMA', job_name => 'ExportTableToProdJob', version => 'COMPATIBLE');
and you must change manually to
h1 := dbms_datapump.open (operation => 'EXPORT', job_mode => 'SCHEMA', job_name => 'ExportTableToProdJob', version => '10.1.0.1');
This creates a 10g1.0.1 or later compatible export data file.
You must have read/write privileges to the folder were the export data file will be created, and imported from. (Oracle Directory Object)

Trying to generate WSRP deployment from JPS complient portlets

In the WebCenter developers guide refer to chapter 18.9.3:
I have a JSR-168 portlet application build on the Servlet 2.3 standard, and now I want to deploy this to the WSRP Portlet container. To do this, first I must generate a WSRP ear file.
In the WebCenter framework there is a jar called wsrp-predeploy.jar.
With this jar I can convert an ear file with a JSR-168 portlet application in it, to a WSRP Portlet container 10.1.32 compatible ear file.
The problem is, I work behind a Windows XP terminal that is protected with the typical firewall / proxysettings inside a big network. It seems wsrp-predeploy.jar is explicitly trying to make a HttpConnectionURL. And this fails.
Also with setting the extra -Dhttp.proxyHost, -Dhttp.proxyPort parameters I have no succes. (Also tried this with the extra -Dhttp.proxySet, -Dhttp.proxyUsername, -Dhttp.proxyPassword)
Is there any workaround for solving above problem?

Hi Steve,
The portlet application (this is: the application containing only the portlets) can be deployed with a normal war deployment profile. JDeveloper itself will take care of generating the wsdls for you, and you do not need to do predeployment.
The application consuming the portlets is a little more complicated. This needs a webcenter deployment profile, and when you want to deploy that on a server, you need to need to run the predeployment tool on the server where you are going to run the app. This time, the predeployment tool will validate the connections to the portlet container and do http calls to that container.
To test the whole setup:
- if you run and test locally, you can use jdev 10.1.3.3 and deploy the portlet ear to the webcenter standalone oc4j container. The consuming app can be run from within JDev using the embedded container.
- if you want to deploy, often the portlet ear and the consuming ear run on the same machine, and predeployment should not be a problem.
Jeroen van Veldhuizen

Trying to generate the spool from at user command...

Hi Gurus,
The spool is not getting created in the foreground, I think I am missing something here, the code is below.
AT USER-COMMAND.
CASE sy-ucomm .
    WHEN 'SEND'.
      PERFORM get_cust_emails.
      LOOP AT i_output.
        READ TABLE i_mail INTO wa_mail WITH KEY kunnr = i_output-rcvprn. " rcvprn is customer number,
        IF sy-subrc IS INITIAL.
          IF wa_mail-smtp_addr IS NOT INITIAL. if the customer has an email then create the entry in i_output_mail.
            i_output_mail = i_output.
            APPEND i_output_mail.
            CLEAR: i_output_mail.
            DELETE i_output.
            CLEAR: i_output.
          ENDIF.
        ENDIF.
      ENDLOOP.
Setting the Print Parameter's for Portrait
      PERFORM f_print_report. " form is below
      SORT i_output_mail BY rcvprn belnr. "rcvprn is the customer number
      PERFORM f_prepare_mail. " form is below
      MESSAGE i307.
      LEAVE LIST-PROCESSING.
     WHEN 'BACK'.
      LEAVE TO SCREEN 0.
    WHEN 'EXIT'.
      LEAVE PROGRAM.
    WHEN 'CANCEL'.
      LEAVE PROGRAM.
ENDCASE.
Subroutines provided below:
FORM f_print_report .
*Program name
DATA : l_prog_name TYPE sy-repid,
         i_print TYPE slis_print_alv.
Local Constants
CONSTANTS: lc_vline TYPE c VALUE '|'.
l_prog_name = sy-repid.
CLEAR: i_events[], wa_events.
wa_events-name = c_top. "'TOP_OF_PAGE'.
wa_events-form = c_top.
APPEND wa_events TO i_events.
CONSTANTS: lc_prtr   TYPE sypdest VALUE 'LP01',
             lc_layout TYPE sypaart VALUE 'X_90_120',
             lc_layout1 TYPE sypaart VALUE 'X_65_255',
             lc_lines TYPE sylinsz VALUE '-120',
             lc_lines1 TYPE sylinsz VALUE '-185',
             lc_mode   TYPE sycallr VALUE 'CURRENT'.
Get the print paramters
CALL FUNCTION 'GET_PRINT_PARAMETERS'
    EXPORTING
      authority              = space
      destination            = lc_prtr
      immediately            = space
      new_list_id            = c_x
      layout                 = lc_layout
      line_size              = lc_lines
      mode                   = lc_mode
      no_dialog              = c_x
      report                 = sy-repid
      user                   = sy-uname
      suppress_shading       = c_x
    IMPORTING
      out_parameters         = i_pr_param
      valid                  = l_valid
    EXCEPTIONS
      archive_info_not_found = 1
      invalid_print_params   = 2
      invalid_archive_params = 3
      OTHERS                 = 4.
CLEAR: g_heading_completed."Indicator for print header
ENDFORM.                    "f_print_report
FORM f_prepare_mail .
LOOP AT i_output_mail.
    l_flag_mail = 'X'.
    CLEAR: l_flag.
    WRITE: /08(1) c_vline, 10(09) i_output_mail-stapa1, 20(1) c_vline,21(10) i_output_mail-datum,
            31(1) c_vline, 32(10) i_output_mail-belnr, 42(1) c_vline,43(15) i_output_mail-total,
            58(1) c_vline, 59(15) i_output_mail-surcrg, 74(1) c_vline,75(05) i_output_mail-kperc,
            80(1) c_vline, 81(15) i_output_mail-betrg, 96(1) c_vline,97(19) i_output_mail-summe,
           116(1) c_vline,117(03) i_output_mail-curcy, 120(1) c_vline.
    AT END OF rcvprn.
      SUM.
      ULINE /8(113).
      WRITE: /8(1) c_vline.
      FORMAT COLOR 3.
      WRITE: 10(09) text-064, 20(01) c_vline,             21(10) space,
              31(1) c_vline, 32(10) space,                42(01) c_vline, 43(15) i_output_mail-total,
              58(1) c_vline, 59(15) i_output_mail-surcrg, 74(1)   c_vline, 75(05) space,
              80(1) c_vline, 81(15) i_output_mail-betrg, 96(1)   c_vline, 97(19) i_output_mail-summe,
             116(1) c_vline,117(03) space,                120(01) c_vline.
      FORMAT COLOR OFF.
      ULINE /8(113).
      NEW-PAGE.
    ENDAT.
    AT END OF rcvprn.
      i_pr_param-linsz = 1000.
      NEW-PAGE PRINT ON PARAMETERS i_pr_param NO DIALOG.
      NEW-PAGE PRINT OFF.
    If spool number is obtained, generate PDF
      IF sy-spono IS NOT INITIAL.
        PERFORM f_generate_pdf.
*Send the PDF as mail attachement
        PERFORM f_send_email.
      ENDIF.
    ENDAT.
ENDLOOP.
ENDFORM.                   " SEND_MAIL
Please check the code and suggest some changes.
Thanks,
Sukumar.

Hi,
The data is getting printed incorrectly, I have coded as you have instructed. But the report output (not emailing) is getting printed ok. The code for that is as below.
FORM f_list_display .
LOOP AT i_output.
    g_flag = c_x.
    CLEAR: g_flag_mail.
    WRITE: /08(1) c_vline, 10(09) i_output-stapa1, 20(1) c_vline,21(10) i_output-datum,
            31(1) c_vline, 32(10) i_output-belnr, 42(1) c_vline,43(15) i_output-total,
            58(1) c_vline, 59(15) i_output-surcrg, 74(1) c_vline,75(05) i_output-kperc,
            80(1) c_vline, 81(15) i_output-betrg, 96(1) c_vline,97(19) i_output-summe,
           116(1) c_vline,117(03) i_output-curcy, 120(1) c_vline,121(10) i_output-rcvprn.
    AT END OF rcvprn.
      SUM.
      ULINE /8(113).
      WRITE: /8(1) c_vline.
      FORMAT COLOR 3.
      WRITE: 10(09) text-064, 20(01) c_vline,        21(10) space,
              31(1) c_vline, 32(10) space,           42(01) c_vline, 43(15) i_output-total,
              58(1) c_vline, 59(15) i_output-surcrg, 74(1)   c_vline, 75(05) space,
              80(1) c_vline, 81(15) i_output-betrg, 96(1)   c_vline, 97(19) i_output-summe,
             116(1) c_vline,117(03) space,           120(01) c_vline.
      FORMAT COLOR OFF.
      ULINE /8(113).
      NEW-PAGE.
    ENDAT.
ENDLOOP.
ENDFORM.                    " F_LIST_DISPLAY
The code which you gave should work as the above code. The above code is for report output and our code is for sending mails to the customers separately, thus we are creating separate spools customer-wise.
Our code for emailing to customers seperately is below.
FORM f_prepare_mail .
LOOP AT i_output_mail.
At new rcvprn.
NEW-PAGE PRINT ON PARAMETERS i_pr_param NO DIALOG.
endat.
l_flag_mail = 'X'.
CLEAR: l_flag.
WRITE: /08(1) c_vline, 10(09) i_output_mail-stapa1, 20(1) c_vline,21(10) i_output_mail-datum,
31(1) c_vline, 32(10) i_output_mail-belnr, 42(1) c_vline,43(15) i_output_mail-total,
58(1) c_vline, 59(15) i_output_mail-surcrg, 74(1) c_vline,75(05) i_output_mail-kperc,
80(1) c_vline, 81(15) i_output_mail-betrg, 96(1) c_vline,97(19) i_output_mail-summe,
116(1) c_vline,117(03) i_output_mail-curcy, 120(1) c_vline.
AT END OF rcvprn.
SUM.
ULINE /8(113).
WRITE: /8(1) c_vline.
FORMAT COLOR 3.
WRITE: 10(09) text-064, 20(01) c_vline, 21(10) space,
31(1) c_vline, 32(10) space, 42(01) c_vline, 43(15) i_output_mail-total,
58(1) c_vline, 59(15) i_output_mail-surcrg, 74(1) c_vline, 75(05) space,
80(1) c_vline, 81(15) i_output_mail-betrg, 96(1) c_vline, 97(19) i_output_mail-summe,
116(1) c_vline,117(03) space, 120(01) c_vline.
FORMAT COLOR OFF.
ULINE /8(113).
NEW-PAGE.
ENDAT.
AT END OF rcvprn.
i_pr_param-linsz = 1000.
NEW-PAGE PRINT OFF.
If spool number is obtained, generate PDF
IF sy-spono IS NOT INITIAL.
PERFORM f_generate_pdf.
*Send the PDF as mail attachement
PERFORM f_send_email.
ENDIF.
ENDAT.
ENDLOOP.
ENDFORM. " SEND_MAIL
Let me know, what could be the error in our code which generates separate spools for customers.
Thanks in advance for the help.
Sukumar.

HT4528 I have 3 iPhones, one Ipad, and two PC's that I have tried to "connect" using one iTunes account and am having issues.I connected iPhone #3 to one PC, it removed all contacts from iPhone #3, replaced w/ contacts from iPhone #2. How can I get back?

I have 3 iPhones, one iPad and 2 PC's, all using the same iTunes account. I want to be able to have each iPhone keep their own list of accounts and music list and the I pad different as well. I want to 2 PC's music list to match. How do I do this?
Additionally, when I connected iPhone #3 to one PC, it removed the contacts from #3 and replaced it with contacts from iPhone #2. How do I get those contacts back and prevent this from happening again?

Hey joshuafromisr,
If you resintall iTunes, it should fix the issue. The following document will go over how to remove iTunes fully and then reinstall. Depending on what version of Windows you're running you'll either follow the directions here:
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
http://support.apple.com/kb/HT1925
or here:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
http://support.apple.com/kb/HT1923
Best,
David

I have acquired a new modem usb modem for my computer which gets me on the internet fine but when I try to load a weg page in Mozilla it tries but always comes up with the error that the connection has timed out. Any Ideas? Thanks

It seems the browser will not let me connect even though the internet is accessed.

Carmell-
When I've had a similar problem, it was because I was accessing the iTunes store from a device I hadn't used before, such as when I upgraded from an iPad 1 to the iPad 2. It was a little confusing to me until I figured it out.
All I had to do was use the ID of my existing account and play along with the iTunes store. As I recall, it asked for my password twice, and the security code from the back of my credit card. After that, downloads proceeded as before.
Fred

Trying to install Firefox, but keep getting a message that I have to restart computer to finish a previous install of firefox.

I have restarted my computer numerous times and I get the message every time.

Run the Firefox program once as Administrator (right-click: Run as Administrator).
If that doesn't solve the problem then do a clean reinstall and remove the Firefox program folder.
* http://kb.mozillazine.org/Software_Update (Software Update not working properly)
* [[Software Update Failed]]

Hello, I'm trying to print a picture but it say's that i have no themes installed. How can i install themes?

It's seemed that i don't have any themes in Iphoto, how can i get them?
Thank you.

Check out OT's post in this thread:
http://discussions.apple.com/thread.jspa?messageID=6394288&#6394288
Also, note his comments here:
http://discussions.apple.com/thread.jspa?messageID=6998840&#6998840
> Look in your User/Library/Application Support/iPhoto folder for a Themes folder. If you find it there move it to the HD/Library/Application Support/iPhoto folder and reboot. Then try iPhoto again. That may save you having to go thru the reinstallation.
Regards
TD

Dear All, today i am trying to generate a chm in Robohelp 11, by combining two topics under a single book but again and again i am facing same issue that is "Cannot open the file: mk:@MSITStore: C:\\Users\..\Desktop\filename.chm"

Dear All, today i am trying to generate a chm in Robohelp 11, by combining two topics under a single book but again and again i am facing same issue that is "Cannot open the file: mk:@MSITStore: C:\\Users\..\Desktop\filename.chm"
Amy_WongWoojinDebbieclawsonmghalpinjwarrenJochem van DietenLee Design
Please help me in solving the same

HI,
Thanks for the response.
I am really tensed for the same...
Actually the error occurs in the following case:
1. I am creating a Parent folder in robohelp with the name ABC..
2. Next Under ABC i have created 2 separate folders say XYZ and EFG.
3. Under XYZ i have created various Topics say 2 or 3.
4. Under EFG i have created various Topics say 7 or 8.
5. Now, i have created a TOC with name for ABC (Parent Folder.)
6. Next i have dragged and dropped my two sub folders that i have created under ABC in Project Set up wizard that is XYZ and EFG, in order to generate the webhelp first and then the CHM file fo rthe same.
7. Webhelp is successfully getting generated.
8. But when i convert the Webhelp to CHM Converter, after few seconds the robohelp gets halt and it shuts up the robohelp, showing a message dialog box that the Adobe Robohelp 11 is Troubleshooting for the error, the Windows manager will get back to you..Someting like this, the .CHM file for the same gets generated on the described path, but when i click on it, it does not open and shows the error as "Cannot open file: mk:@MSITStore: C:\\Users\..\Desktop\filename.chm".
Please help me in sorting the above issue.
According to me:
I think i am Lacking in the two things:
1. How to link all the topics with the parent folder.
2. How to Merge the projects.
Can you please provide me the link where i can get tutorial to create a TOC for multiple files in a same TOC and to generate a chm for them.
Actually for single project folder i have worked successfully. But, its first time i have to create a chm with lot many sub folders in it, as like one create a book.
Please help
Thanks & Regards,
dhm

How to Generate Synchronized pulses across two separate cards on a PXI system

Hey,
I'm trying to generate three pulses from my PXI System for triggering purposes. I have two cards (PXI 6259 and PXI 6115) , each with two counter/timers on them. The 6259 has 32 bit timers, and the 6115 has 24 bit timers.
Up until now, I only needed two pulses. One was 180us long at 20 Hz, and the other is 5us at 20 Hz, starting 150us after the beginning of the first pulse. I was able to achieve this by generating both pulses on my 6115 card by triggering the shorter pulse off of the rising digital edge of the longer pulse and giving the DAQmx Counter/Timer task an initial delay of 150us.
The third pulse needs to be identical to the short pulse, only it needs to occur 20us early (130us after the start of the wide pulse). I tried to generate it using the same technique as I used when generating the short pulse, only generating the pulse and reading in the rising digital edge trigger on my 6259 card instead of the 6115.
The result was that my pulse trains were asynchronous and the pulse generated on the 6259 card was constantly shifting to the left.
This puzzled me, so I wrote up a little dummy program to test generating triggered pulses. The results were that when I generated two pulses on the same card, they were always synchronized; however when I generated pulses on separate cards, one of the pulses always shifted.
I was hoping somebody could suggest a reason that the pulses across cards are asynchronous even though I'm reading in a digital trigger and hopefully a way to rectify the situation and synchronize all of my pulses.

The problem, in a nutshell, is that the timebases on the two boards have manufacturing tolerances that will cause them to differ from one another. The accuracy error is a small fraction of a percent, but the effect on the phasing of your pulses will be cumulative. That's why you saw the one set of pulses "shifting to the left."
The solution is to make sure each board derives its pulse timing from a single common timebase. Fortunately, this is pretty easy to specify with DAQmx, just a little tricky to find. In the chain of VI's you call to configure the counter pulses, insert a DAQmx Channel property node. From memory, I *think* you should be looking under something similar to "Counter Output->General->Timebase->Timebase.Src"
Right click and create a constant or control to define the timebase source. You should get a dropdown list that includes a wide variety of choices. Among them are each of the boards' 20 MHz clocks. By default each task will use a timebase from its own board but this technique lets you route one board's timebase over the PXI backplane with that single property node setting. DAQmx does most of the dirty work behind the scenes.
-Kevin P

Generate a url from a report or function module

Hi,
I'm trying to generate a url from a report and tried using the function module WWW_ITAB_TO_HTML in the report program, as , but i'm not able to get the expected results. The code is given below. Could someone please try and help me resolve this issue. Thanks in advance.
DATA: emp_name TYPE char80.
DATA: it_itabex TYPE zdb_ex_tty,
it_emp TYPE TABLE OF zis_emp,
it_org TYPE TABLE OF zis_org,
it_pos TYPE TABLE OF zis_pos,
it_pos_alloc TYPE TABLE OF zis_pos_alloc,
it_res TYPE TABLE OF zis_res,
it_res_alloc TYPE TABLE OF zis_res_alloc,
ls_itabex TYPE zdb_ex_s.
DATA: lv_filename TYPE string,
lv_path TYPE string,
lv_fullpath TYPE string,
lv_replace TYPE i.
DATA qstring LIKE it_itabex OCCURS 10.
DATA: url(200), url2(200), url3(200), fullurl(200).
FIELD-SYMBOLS: <fs_emp> LIKE LINE OF it_emp,
<fs_org> LIKE LINE OF it_org,
<fs_pos> LIKE LINE OF it_pos,
<fs_pos_alloc> LIKE LINE OF it_pos_alloc,
<fs_res> LIKE LINE OF it_res,
<fs_res_alloc> LIKE LINE OF it_res_alloc.
** Report Program to export data from database to Excel.
** Populate all the tables that have to be exported.
SELECT * FROM zis_org INTO TABLE it_org.
SELECT * FROM zis_pos INTO TABLE it_pos.
SELECT * FROM zis_pos_alloc INTO TABLE it_pos_alloc.
SELECT * FROM zis_emp INTO TABLE it_emp.
SELECT * FROM zis_res_alloc INTO TABLE it_res_alloc.
SELECT * FROM zis_res INTO TABLE it_res.
** Append the Column Header
CLEAR ls_itabex.
ls_itabex-ipp_pos_id = 'IPP Pos ID'.
ls_itabex-emp_name = 'Name'.
ls_itabex-dt_of_join = 'JoinedOn'.
ls_itabex-emp_status = 'Status'.
ls_itabex-org_name = 'Org'.
ls_itabex-prj_name = 'Project'.
ls_itabex-mgr_name = 'Line'.
ls_itabex-designation = 'Designation'.
ls_itabex-specialization = 'Specialization'.
APPEND ls_itabex TO it_itabex.
** Append all the tables into one internal table
LOOP AT it_pos_alloc ASSIGNING <fs_pos_alloc>.
CLEAR ls_itabex.
ls_itabex-ipp_pos_id = <fs_pos_alloc>-ipp_pos_id.
READ TABLE it_emp ASSIGNING <fs_emp> WITH KEY emp_guid = <fs_pos_alloc>-emp_guid.
IF sy-subrc = 0.
CONCATENATE <fs_emp>-emp_fname <fs_emp>-emp_lname INTO ls_itabex-emp_name SEPARATED BY space.
ls_itabex-dt_of_join = <fs_emp>-dt_of_join.
ls_itabex-emp_status = <fs_emp>-emp_status.
ls_itabex-specialization = <fs_emp>-specialization.
ENDIF.
READ TABLE it_pos ASSIGNING <fs_pos> WITH KEY ipp_pos_id = <fs_pos_alloc>-ipp_pos_id.
IF sy-subrc = 0.
ls_itabex-designation = <fs_pos>-designation.
READ TABLE it_org ASSIGNING <fs_org> WITH KEY org_id = <fs_pos>-org_id.
IF sy-subrc = 0.
ls_itabex-org_name = <fs_org>-org_name.
ls_itabex-mgr_name = <fs_org>-mgr_name.
ENDIF.
ENDIF.
READ TABLE it_res ASSIGNING <fs_res> WITH KEY org_id = <fs_org>-org_id.
ls_itabex-org_name = <fs_org>-org_name.
APPEND ls_itabex TO it_itabex.
ENDLOOP.
url = 'http://testweb/scripts/wgate/zvw10a/!?~language=en'.
url2 = '&~OkCode(LGON)=LGON&login-login_user='.
url3 = '&vbcom-vbeln='.
CONCATENATE url url2 url3 INTO fullurl.
WRITE: /'Staffing Excel'.
CALL FUNCTION 'WWW_SET_URL'
EXPORTING
offset = 12
length = 10
func = fullurl
TABLES
query_string = qstring
EXCEPTIONS
invalid_table = 1
OTHERS = 2.
Thanks & Regards,
Preethi.

Check the below example program :
data: begin of itab occurs 0,
      matnr type mara-matnr,
      mtart type mara-mtart,
      matkl type mara-matkl,
      groes type mara-groes,
      end of itab.
data: ifields type table of w3fields with header line.
data: ihtml   type table of w3html   with header line.
select * into corresponding fields of table itab
          from mara up to 100 rows.
call function 'WWW_ITAB_TO_HTML'
EXPORTING
TABLE_ATTRIBUTES       = 'BORDER=1'
TABLE_HEADER           =
    ALL_FIELDS             = 'X'
tables
    html                   = ihtml
    fields                 = ifields
ROW_HEADER             =
    itable                 = itab
check sy-subrc = 0.
call function 'GUI_DOWNLOAD'
     exporting
          filename = 'c:\test.html'
     tables
          data_tab = ihtml.
Reward points if it is helpful
Thanks
Seshu

Trying to generate a signal from two signals (EMG) that I have acquired from my NI USB

Similar Messages

Maybe you are looking for