TS1702 i've an iphone 3.1.3. sometimes, i have problems opening all the apps i downloaded in the past 4 months. other apps would open but the recent ones will begin to boot and then close itself. once, it persisted for over a week. pls help as am frustrat

i've an iphone 3.1.3. sometimes, i have problems opening all the apps i downloaded in the past 4 months. other apps would open but the recent ones will begin to boot and then close itself. once, it persisted for over a week. it staarted again this evening, pls help as am frustrated. NB- i checked for apps update but all my apps are up-to-date. CT

Try the usual steps: restart, reset, restore.
http://support.apple.com/kb/HT1430
http://support.apple.com/kb/HT1414
If restoring using a backup doesn't help, try restoring the iPhone to factory settings and try for a while with just the Apple-included apps, to make sure it's not an issue with a third-party app. If it still has problems, it may have a hardware problem and will need to be sent to Apple.
Regards.

Similar Messages

Whenconnecting to the internet thru safari, the requested page will begin to appear and then the screen will revert to the iPad home page. Have powered the ipad down and back yp with no change.

When I connect to the internet thru Safari, the requested page will begin to appear and then revert to the Ipad home page. I have powered of and back on and wi-fi signal is strong. any suggestions.

Safari crash regularly
https://discussions.apple.com/thread/2460899?tstart=30

After the ios7 update I have been unable to open the i-tunes store on my i-phone5, it basically flashes up for two seconds and then closes itself down, anyone else had anything similar and no a fix?

Since updating to ios7.0.2 on my i-phone5 I have been unable to open the i-tunes store app, basically it just opens for a second or two then shuts itself down, I've tried a soft reset, turning on and off, closing down all running apps but nothing seems to work, anyone else had the same problem and no how to fix it?

Hey there Fistycuff,
It sounds like iTunes launches for a split second, then quits unexpectedly.
I would recommend a few things for this issue. First, close all the running apps on the phone:
iOS: Force an app to close
http://support.apple.com/kb/ht5137
Double-click the Home button.
Swipe left or right until you have located the app you wish to close.
Swipe the app up to close it.
When you have done that, sign out of your iTunes account in Settings > iTunes and App stores, and restart the phone:
iOS: Turning off and on (restarting) and resetting
http://support.apple.com/kb/ht1430
If the issue persists, I would next backup your device to iTunes, and restore it:
iOS: How to back up and restore your content
http://support.apple.com/kb/HT1766
Thank you for using Apple Support Communities
Regards,
Sterling

Cloned my hard drive. now acrobat won't work. just opens for 7 seconds and then closes itself. huh?

Anybody got a clue why acrobat wont work after cloning entire computer to a new hard drive?
I 'repaired ' the installation and rebooted twice.
Acrobat just shuts down after 5-10 seconds.
I need help.
-Steve

Mavericks is free but a jump from 10.6 to 10.9 might break a lot of other software (particularly if running any PPC-only generation software) which could be costly to replace. Yes, it will have to be done someday but if the OP's computer holds out a few more years then the OP will have saved buying all the Mavericks generation software that will be broken when OS 12.2 comes out and can make the jump directly.
So says somebody who still runs a G4 with iTunes 7.5 and is not looking forward to the day it dies and has to buy the "newest and best".

11'' MacBook Air restart itself whenever it idle for 3 seconds. Pls help.

My macbook air keep restarting itself whenever it idle for 3 seconds. I have checked the screen saver and battery setting part and everything is fine. I bought this in 2012. I never spill water on my macbook. Pls help.

I owned it most of the time
Hardware Information:
          MacBook Air (11-inch, Mid 2011)
          MacBook Air - model: MacBookAir4,1
          1 1.6 GHz Intel Core i5 CPU: 2 cores
          4 GB RAM
Video Information:
          Intel HD Graphics 3000 - VRAM: 384 MB
System Software:
          Mac OS X 10.7.5 (11G63b) - Uptime: 0 days 0:0:48
Disk Information:
          APPLE SSD SM128C disk0 : (121.33 GB)
                    disk0s1 (disk0s1) <not mounted>: 209.7 MB
                    Macintosh HD (disk0s2) /: 120.47 GB (6.51 GB free) (Low!)
                    Recovery HD (disk0s3) <not mounted>: 650 MB
USB Information:
          Apple Inc. FaceTime Camera (Built-in)
          Apple Inc. Apple Internal Keyboard / Trackpad
          Apple Inc. BRCM20702 Hub
                    Apple Inc. Bluetooth USB Host Controller
FireWire Information:
Thunderbolt Information:
          Apple, Inc. MacBook Air
Kernel Extensions:
Startup Items:
          HWNetMgr: Path: /Library/StartupItems/HWNetMgr
          HWPortDetect: Path: /Library/StartupItems/HWPortDetect
Problem System Launch Daemons:
          [not loaded] ftp-proxy.plist 3rd-Party support link
Problem System Launch Agents:
Launch Daemons:
          [loaded] com.microsoft.office.licensing.helper.plist 3rd-Party support link
Launch Agents:
User Launch Agents:
          [loaded] com.google.keystone.agent.plist 3rd-Party support link
User Login Items:
          iTunesHelper
          Dropbox
          PowerBlock
Internet Plug-ins:
          FlashPlayer-10.6: Version: 11.1.102.55 3rd-Party support link
          Flash Player: Version: 11.1.102.55 Outdated! Update
          QuickTime Plugin: Version: 7.7.1
          JavaAppletPlugin: Version: 14.6.0 - SDK 10.7 Outdated! Update
          SharePointBrowserPlugin: Version: 14.0.0 3rd-Party support link
Audio Plug-ins:
          iSightAudio: Version: 7.7.1 - SDK 10.7
User Internet Plug-ins:
          Picasa: Version: 1.0 3rd-Party support link
3rd Party Preference Panes:
          Flash Player 3rd-Party support link
Bad Fonts:
          None
Old Applications:
          None
Time Machine:
          Time Machine not configured!
Top Processes by CPU:
              84%          mds
              11%          mdworker
               6%          WindowServer
               4%          EtreCheck
               3%          hidd
Top Processes by Memory:
          176 MB          System Preferences
          98 MB          Safari
          90 MB          WebProcess
          70 MB          Dropbox
          51 MB          mds
Virtual Memory Information:
          2.04 GB          Free RAM
          982 MB          Active RAM
          188 MB          Inactive RAM
          838 MB          Wired RAM
          217 MB          Page-ins
          0 B          Page-outs

[SOLVED] Cloning boot and var partitions to a new drive for booting

Ok first of all here's my setup:
fakeraid (dmraid) / and home on an OCZ Revodrive
boot with GRUB on a flash drive (since fakeraid doesn't support grub)
var and downloads/media folder on a 500GB WD Caviar drive
When I originally installed Arch I had the Caviar drive in my home server in a RAID5 array, so that's why I opted to install boot and grub on a flash drive simply for booting. Now that I have the drive in my desktop I've cloned the flash drive's partitions and MBR using dd:
#dd if=/dev/sde of=~/MBR.img bs=512 count=1
#dd if=/dev/sde1 of=~/boot.img
#dd if=/dev/sdc1 of=~/var.img
I then backed up my downloads/media partition, then removed the partition table, then used dd to put the img files on the Caviar drive.
#dd if=~/MBR.img of=/dev/sdc bs=512 count=1
#dd of=~/boot.img of=/dev/sdc1
#dd of=~/var.img of=/dev/sdc2
I also created labels for the filesystems and put those in fstab.
I'm able to mount both partitions, however I can't boot from the drive. I get a 'grub hard disk error' (no error number) when I put it as my first drive in the BIOS.
I can still use the flash drive as the first hard drive in the BIOS and boot from it, then it mounts the dmraid root partition and boots successfully. It is also able to mount the var and boot partitions in fstab.
Basically the only problem is that the MBR is somehow wrong. I then tried booting back into an Arch live USB and installing GRUB from the prompt:
grub
grub>setup (hd4,0) (in this case the Caviar drive's boot partition was /dev/sde1
So essentially what I'm asking is how GRUB handles the MBR. Is it specific to the partition table of the drive in which it resides when it's originally installed? For instance, since I had an 8GB flash drive with 2 partitions when I installed GRUB, is the backed up MBR no good for a 500GB drive with 3 partitions?
I have everything backed up so I can start with a fresh /boot and /var if need be....I'm just not sure where to start.
Thanks in advance.
Last edited by DarksideEE7 (2011-02-13 23:25:31)

Sorry, I forgot to mention that I tried to install GRUB from the GRUB shell in a live Arch USB. It failed on a few non-critical parts, and succeeded on the last part. I'm going to try again shortly, possibly I did something wrong. GRUB is able to find the stage files using:
#grub
grub>find /grub/stage1
grub> find /grub/stage1
(hd0,0)
(hd5,0)
grub>
(hd0,0) is the desired boot drive, while (hd5,0) is the current bootable flash drive with /boot and GRUB installed.
Here is the output of fdisk -l:
WARNING: GPT (GUID Partition Table) detected on '/dev/sde'! The util fdisk doesn't support GPT. Use GNU Parted.
Disk /dev/sde: 2000.4 GB, 2000398934016 bytes
256 heads, 63 sectors/track, 242251 cylinders, total 3907029168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/sde1 1 3907029167 1953514583+ ee GPT
Disk /dev/sdb: 60.0 GB, 60022480896 bytes
255 heads, 63 sectors/track, 7297 cylinders, total 117231408 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xedb72db9
Device Boot Start End Blocks Id System
/dev/sdb1 * 2048 206847 102400 7 HPFS/NTFS
/dev/sdb2 206848 117227519 58510336 7 HPFS/NTFS
Disk /dev/sdd: 40.0 GB, 40018599936 bytes
255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Disk /dev/sdd doesn't contain a valid partition table
Disk /dev/sdc: 40.0 GB, 40018599936 bytes
32 heads, 32 sectors/track, 76329 cylinders, total 78161328 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xb8372fcd
Device Boot Start End Blocks Id System
/dev/sdc1 32 21484543 10742256 83 Linux
/dev/sdc2 21484544 156317695 67416576 83 Linux
Disk /dev/sda: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x8497e059
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 206847 102400 83 Linux
/dev/sda2 206848 42149887 20971520 83 Linux
/dev/sda3 42149888 976773167 467311640 83 Linux
Disk /dev/dm-0: 80.0 GB, 80035053568 bytes
32 heads, 32 sectors/track, 152654 cylinders, total 156318464 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 65536 bytes / 131072 bytes
Disk identifier: 0xb8372fcd
Device Boot Start End Blocks Id System
/dev/dm-0p1 32 21484543 10742256 83 Linux
Partition 1 does not start on physical sector boundary.
/dev/dm-0p2 21484544 156317695 67416576 83 Linux
Disk /dev/dm-1: 11.0 GB, 11000070144 bytes
255 heads, 63 sectors/track, 1337 cylinders, total 21484512 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 65536 bytes / 131072 bytes
Alignment offset: 49152 bytes
Disk identifier: 0x00000000
Disk /dev/dm-1 doesn't contain a valid partition table
Disk /dev/dm-2: 69.0 GB, 69034573824 bytes
255 heads, 63 sectors/track, 8392 cylinders, total 134833152 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 65536 bytes / 131072 bytes
Disk identifier: 0x00000000
Disk /dev/dm-2 doesn't contain a valid partition table
Disk /dev/sdf: 8086 MB, 8086618112 bytes
249 heads, 62 sectors/track, 1023 cylinders, total 15794176 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x8497e059
Device Boot Start End Blocks Id System
/dev/sdf1 * 62 200693 100316 83 Linux
/dev/sdf2 200694 15794175 7796741 83 Linux
I'm using dmraid, so just to be clear I've configured the raid using:
#modprobe dm_mod
#dmraid -ay
Then I saw the array stored in /dev/mapper/silXXXXX. I then created partitions for /boot, /, and home. At that time I was hoping to get GRUB working with the AUR package grub2-dmraid. I wasn't able to get it working for some time, so I just went ahead and installed boot and GRUB to a separate USB flash drive.
Here is the output of df -h:
Filesystem Size Used Avail Use% Mounted on
udev 10M 268K 9.8M 3% /dev
/dev/mapper/sil_bgbgdjaddicbp1
11G 5.3G 4.3G 56% /
shm 6.0G 584K 6.0G 1% /dev/shm
/dev/mapper/sil_bgbgdjaddicbp2
64G 38G 23G 63% /home
/dev/sda1 95M 16M 75M 18% /boot
/dev/sda2 19G 142M 19G 1% /var
/dev/sda3 439G 148G 269G 36% /home/l33/Torrents
none 1000M 132K 1000M 1% /tmp
shm 6.0G 584K 6.0G 1% /dev/shm
/dev/sde1 1.8T 1.1T 665G 62% /mnt/Green
and cat /etc/mtab
proc /proc proc rw,nosuid,nodev,noexec,relatime
sys /sys sysfs rw,nosuid,nodev,noexec,relatime
udev /dev devtmpfs rw,nosuid,relatime,size=10240k,nr_inodes=1022975,mode=755
/dev/mapper/sil_bgbgdjaddicbp1 / ext4 rw,noatime,barrier=1,stripe=32,data=ordered
devpts /dev/pts devpts rw 0 0
shm /dev/shm tmpfs rw,nosuid,nodev 0 0
/dev/mapper/sil_bgbgdjaddicbp2 /home ext4 rw,noatime 0 0
/dev/sda1 /boot ext2 rw 0 0
/dev/sda2 /var reiserfs rw,noatime 0 0
/dev/sda3 /home/l33/Torrents ext4 rw,noatime 0 0
none /tmp tmpfs rw,nosuid,nodev,noatime,size=1000M,mode=1777 0 0
shm /dev/shm tmpfs rw,nosuid,nodev,size=6G 0 0
rpc_pipefs /var/lib/nfs/rpc_pipefs rpc_pipefs rw 0 0
nfsd /proc/fs/nfsd nfsd rw,noexec,nosuid,nodev 0 0
/dev/sde1 /mnt/Green ext4 rw 0 0
Also I don't have a /proc/mdstat. That's only for mdadm RAID setups, right? It's been quite some time since I've used mdadm so I can't remember.
EDIT:
So I booted into a live Arch USB and entered the grub shell. I ran:
#grub
grub> root (hd3,0)
Filesystem type is ext2fs, partition type 0x83
grub> setup (hd3)
Checking if "/boot/grub/stage1" exists.....no
Checking if "/grub/stage1 exists.......yes
Checking if "/grub/stage2 exists.......yes
Checking if "/grub/e2fs_stage1_5 exists....yes
Running "embed /grub/e2fs_stage1_5 (hd3)".....25 sectors are embedded.
succeeded
Running "install /grub/stage1 (hd3) (hd3))1+25 p (hd3,0)/grub/stage2 /grub/menu.lst".......succeeded
Done.
Last time I recall more errors than this, then it reporting that one was a non-critical error, so I think the problem may be solved. More to come.
Last edited by DarksideEE7 (2011-02-13 23:18:44)

When I try to open Adobe Reader, it just opens a gray page and then closes by itself. This also appl

When I try to open Adobe Reader, it just opens a gray page and then closes by itself. This also applies to any pdf files I try to access; they'd all follow the same pattern: Gray page-->automatically closes after 2 to 3 seconds time. I have tried accessing the Eula.exe via C:\Program Files (x86)\Adobe\Reader 11.0\Reader, however, the only available button for me to click is the "Decline" button and not the "Accept" license agreement. Please help!
THanks

Thanks for your help!!!!

I have the iPhone 4, recently installed ios6 now my phone constantly turns itself off, keeps freezing and then 2 or 3 times in the space of 24hrs it has to be restored to factory settings. This has gone on for over a week.

I have the iPhone 4, recently installed ios6 now my phone constantly turns itself off, keeps freezing and then 2 or 3 times in the space of 24hrs it has to be restored to factory settings. This has gone on for over a week.

If all basic troubleshooting has been tried and a restore as new does not resolve, take it to Apple for evalation and possible replacement.

My iMac starts up and then shuts itself down during the boot up process. it shuys down half way through the Apple logo appearing. any ideas how to fix?

My iMac starts up and then shuts itself down during the boot up process. it shuys down half way through the Apple logo appearing. any ideas how to fix?

Hi daveormond,
I'm sorry to hear you are having these issues with your iMac. If you continue to have issues with your Mac shutting down part way through the boot up process, you may find the troubleshooting steps outlined in the following articles helpful (given your description, it sounds like it could be either issue, or a combination of both):
Mac OS X: Gray screen appears during startup - Apple Support
OS X: When your computer spontaneously restarts or displays "Your computer restarted because of a problem." - Apple Support
Regards,
- Brenden

I am having to run v3.5.10 because even now with latest 3.6 that version - every 30 seconds or so I hear a process open and then close. Can't track it down even in task manager - too brief but it's insistent! So stuck having to use 3.5

I have to use V3.5.10 despite wanting to run 3.6 (just updated to 3.6.6 too). However when I run 3.6 I hear thru my sounds set up a process open briefly and then close every 30 seconds or so - it's very regular and insistent and I'd like to know what it is and why. It's too brief to spot in Task manager processes listing. This did happen once under 3.5 I seem to recall but was cured when it upgraded.
== This happened ==
Every time Firefox opened
== Pretty much soon after I first applied and ran 3.6

My Win sounds give me a sound each time an app or process opens and another when it closes - thus I know from that any time something happens.
I have 3.6.6 on as well as 3.5.10 - so can run either. But running .3.6.6 despite being update still has this odd process open and close every half minute.

Facebook app begins to open up and then close immediately

When I am opening up the Facebook application on my iPhone, it just opens the screen and then closes right away.
Does anybody know why? I've powered down and back up, but it still does the same. My phone is just a couple of days old, but I've done the software updates.

I starting having this problem yesterday, for the second time in two weeks (I got my iPhone on the 26th of July). I did a complete restore last night. i got all of my data re-entered into each program. then, i switched my language to Japanese, and all apps started crashing again. I tried un-syncing a bunch of them, re-synching, then synching only part of the 80+ apps I have (okay, I know I'm an app junkie). Hard re-setting didn't work. Nothing did.
I was actually thinking of taking it back and reactivating my old phone.
Then I tried something simple. I re-downloaded a free app (Hangman) directly to my iPhone via the apple store. BAM! Hangman worked, and so did everything else.
The cause of my problem may not have been the same as everyone else's, but here is what I think worked.
1) In OS X on a mac, if something goes awry with a program, you usually can fix it by deleting a plist file.
2) Since you cannot do that on your iPhone, a corrupted plist file somewhere in the iPhone was refreshed/fixed by re-downloading the software directly to the phone.
I know that elsewhere, on Maccast specifically, I heard that it is best to never download programs directly to your phone (it is always better to sync them through iTunes), but this has me thinking otherwise. Once I get iPhone working again, I may try to never again connect the iPhone to iTunes again. I guess this means listening to podcasts ONLY on my other (STABLE, NON-CRASHING) iPod, the classic... so even though I bought the iPhone in part so that I dont have to take a PHONE and a MUSIC PLAYER when I leave the house, then I will have to take two devices anyway...

How to save and then close document Using Acrobat 9 (URGENT)

I have been looking for a soultion for long time now but
couldn't find any.
I'm using a dynamic PDF form desgined using LC Desginer and created a button that should save the current opened form in the same location (no need to define the location because what I want to use is the command File -> Save) and then close the application (I'm using Acrobat 9 Pro Extended).
I tried many scripts and gone throw JavaScript™ for Acrobat® API Reference but no luck.
Once I click on the button I get the following error: NotAllowedError: Security settings prevent access to this property or method.
Will you please help in this issue as it took long time and my project manager is pushing to get resolved ASAP.
Guys, I'm new to this kind of tecnology so please be patient with me.
Thanks in advance for your valuable help.
The code I used in click event of the button is as follow:
try{
     var myDoc = app.newDoc();
     myDoc.saveAs();
     myDoc.closeDoc(true);
catch (e)
     xfa.host.messageBox(""+e);
I used this earlier and got the same error:
try{
      var myDoc = event.target;
     myDoc.saveAs();
catch (e)
     xfa.host.messageBox(""+e);

Hi Niall,
function(){return A.apply(null,[this].concat($A(arguments)))}
function(){return A.apply(null,[this].concat($A(arguments)))}
The app.execMenuItem works here. Is your form designed to be opened in Acrobat/Reader or are you opening the form in html?
The form will be opened by Acrobat/Reader. The statement worked but what I need is to save the PDF in the current location without popping up the Save As dialog box. In other words I would like to perform Ctrl+Saction and then exit the application not only close the form because the Content Management Solution we are using will require the application to be closed so it can CheckIn the document.
I tried to use app.execMenuItem("Save"); but it seems it is not working because once I try to close the application or the form using app.execMenuItem("Close"); the do you want to save changes to "FORM" before closing? dialog box pops-up.
For closing the application I tried app.execMenuItem("Exit"); and I got this error: InvalidArgsError: Invalid arguments.
function(){return A.apply(null,[this].concat($A(arguments)))}
function(){return A.apply(null,[this].concat($A(arguments)))}Also you may want to consider how you are reader enabling the form. If you are using Acrobat to extend the form, then certain features like database connections will not work.
The customer has Adobe LC Reader Extension so I will use it to extend the PDF but right now I do use Acrobat so I don't need to extend the PDF everytime I need to test it.
Can I get all the arguments that execMenuItem uses?
I really appreciate your help Niall.
PS: I couldn't reply earlier yesterday because my work is on the server and I was at home (my time is +3 GMT it was night when I got your reply)
Regards
Mazen

How to save and then close a PDF Using Acrobat 9 (URGENT)

I have been looking for a soultion for long time now but
couldn't find any.
I'm using a dynamic PDF form desgined using LC Desginer and created a button that should save the current opened form in the same location (no need to define the location because what I want to use is the command File -> Save) and then close the application (I'm using Acrobat 9 Pro Extended).
I tried many scripts and gone throw JavaScript™ for Acrobat® API Reference but no luck.
Once I click on the button I get the following error: NotAllowedError: Security settings prevent access to this property or method.
Will you please help in this issue as it took long time and my project manager is pushing to get resolved ASAP.
Guys, I'm new to this kind of tecnology so please be patient with me.
Thanks in advance for your valuable help.
The code I used in click event of the button is as follow:
     var myDoc = app.newDoc();
     myDoc.saveAs();
     myDoc.closeDoc(true);
catch (e)
     xfa.host.messageBox(""+e);
I used this earlier and got the same error:
try{
      var myDoc = event.target;
     myDoc.saveAs();
catch (e)
     xfa.host.messageBox(""+e);
try{

Hi Niall,
function(){return A.apply(null,[this].concat($A(arguments)))}
function(){return A.apply(null,[this].concat($A(arguments)))}
The app.execMenuItem works here. Is your form designed to be opened in Acrobat/Reader or are you opening the form in html?
The form will be opened by Acrobat/Reader. The statement worked but what I need is to save the PDF in the current location without popping up the Save As dialog box. In other words I would like to perform Ctrl+Saction and then exit the application not only close the form because the Content Management Solution we are using will require the application to be closed so it can CheckIn the document.
I tried to use app.execMenuItem("Save"); but it seems it is not working because once I try to close the application or the form using app.execMenuItem("Close"); the do you want to save changes to "FORM" before closing? dialog box pops-up.
For closing the application I tried app.execMenuItem("Exit"); and I got this error: InvalidArgsError: Invalid arguments.
function(){return A.apply(null,[this].concat($A(arguments)))}
function(){return A.apply(null,[this].concat($A(arguments)))}Also you may want to consider how you are reader enabling the form. If you are using Acrobat to extend the form, then certain features like database connections will not work.
The customer has Adobe LC Reader Extension so I will use it to extend the PDF but right now I do use Acrobat so I don't need to extend the PDF everytime I need to test it.
Can I get all the arguments that execMenuItem uses?
I really appreciate your help Niall.
PS: I couldn't reply earlier yesterday because my work is on the server and I was at home (my time is +3 GMT it was night when I got your reply)
Regards
Mazen

My photoshop opens, then closes itself since enrolling in creative cloud. I reinstalled - same

My photoshop opens, then closes itself since enrolling in creative cloud. I reinstalled - same. I use photoshop every day - HELP>

So - I could get no reply on forums so I attempted to speak, on a web chat, to technical support. I waited an hour as the nine people in front of me in the queue were dealt with. Then I outlined my problem, set out above: signed out of CC as soon as I logged in. Tried all the fixes suggested all over the forums and one which was posted on the site by the CC team. No joy. Can't use apps now because when I try to use Photoshop CC (which needs to be authorised at the start of my subscription) it now requires a sign in and offers me only the trial version. "Ah," said my support assistant - you'll need to contact Technical Support. "All the options I was offered online were technical problems," I replied. "This is customer services;" he said, "I'll post you the link". The link sent me back to the page where I started and led me to him. What a shambles. So I have just received an email informing me that Adobe had successfully collected my monthly payment. And I have a service which I can't use. Brilliant.

TS1373 my 5th generation ipod acts like it is going to sync and then "ejects" itself before even 1 song can be synced. It then doesnt recognize that it has been ejected and keeps the"do not disconnect" icon on the screen even after unplugging. What do I

my 5th generation ipod acts like it is going to sync and then "ejects" itself before even 1 song can be synced. It then doesnt recognize that it has been ejected and keeps the"do not disconnect" icon on the screen even after unplugging. What do I do? it also makes a lot of noise while connected to the computer.

Is the camera damaged? Could be a hardware problem.
Try:
Close the Camera app in the multitasking bar, then try again.
Restart/Reset/Restore your iPod. In that order.

TS1702 i've an iphone 3.1.3. sometimes, i have problems opening all the apps i downloaded in the past 4 months. other apps would open but the recent ones will begin to boot and then close itself. once, it persisted for over a week. pls help as am frustrat

Similar Messages

Maybe you are looking for