UCCE - JTAPI gateway - anyone using custom JavaRunTimeOptions ?

The JTAPI gateway settings are in PG\CurrentVersion\JGWS\jgw1\JGWData\Config. The defaults for JavaRunTimeOptions include "-Xms32m -Xmx256m".
This defines the default min stack size as 32MB and the default max stack size as 256MB.
I'd like to increase the min stack size and max stack size. Sun recommend server components should have these pretty high, and the same. There's 4GB of RAM in the PG and it's only using 1.3GB. I'm thinking min 256MB and max 512MB, or something like that.
The reason is the customer's network management system gets a lot of noise from the continual reporting by the JTAPI gateway that the JVM on 1 of the PGs has less than 50% free memory. This fills up the log and hides more important things.
Sure, you can restart the gateway and it will be Ok for a while, but that's not a solution.
Quite frankly, these settings look a bit low to me when there are close to 1000 IP phones being observed.
Have any of you bumped these up? I'm not expecting any problems if I do that, but am looking for your experiences.
Regards,
Geoff

Hi Sefjelstad,
You can refer the section "How Cisco IPCC Remote Agent Option Works with an Analog Phone" from page 70 onwards in the below link,
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/icm_enterprise/icm_enterprise_7_5/user/guide/ipcc75mag.pdf
Note: I have not done any of these implementations yet.
Thanks,
Anand
Pls rate helpful posts !!

Similar Messages

OSB11g: Issue with nodemanager nmConnect after using custom keystore

Environment: OSB 11g ( 4 manages servers in cluster, 1 admin server)
Issue:
For interacting with Paycorp payment gateway, we have used custom identity and trust keystore. For that we have made changes in admin server and all managed servers in Keystore tab (in admin console) and added PaycorpPKI credential mapper in security realms -> myRealm -> Providers -> Credential Mapping.
Things are working fine for OSB code as we are able to connect to secured paycorp gateway by doing these steps.
BUT by doing these changes, the nodemanager command nmConnect('weblogic','welcome1','x.x.x.x',5556,'MyOSBDomain') is not able to connect to node manager.
The exception is:
wls:/offline> nmConnect('weblogic','welcome1','x.x.x.x',5556,'MyOSBDomain')
Connecting to Node Manager ...
<18/04/2011 4:46:26 PM EST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=thawte Primary Root CA - G3,OU=(c) 2008 thawte\, Inc. - For authorized use only,OU=Certification Services Division,O=thawte\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<18/04/2011 4:46:26 PM EST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<18/04/2011 4:46:26 PM EST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 2,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<18/04/2011 4:46:26 PM EST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GlobalSign,O=GlobalSign,OU=GlobalSign Root CA - R3". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<18/04/2011 4:46:26 PM EST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "OU=Security Communication RootCA2,O=SECOM Trust Systems CO.\,LTD.,C=JP". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<18/04/2011 4:46:26 PM EST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=VeriSign Universal Root Certification Authority,OU=(c) 2008 VeriSign\, Inc. - For authorized use only,OU=VeriSign Trust Network,O=VeriSign\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<18/04/2011 4:46:26 PM EST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=KEYNECTIS ROOT CA,OU=ROOT,O=KEYNECTIS,C=FR". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<18/04/2011 4:46:26 PM EST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GeoTrust Primary Certification Authority - G3,OU=(c) 2008 GeoTrust Inc. - For authorized use only,O=GeoTrust Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<18/04/2011 4:46:26 PM EST> <Warning> <Security> <BEA-090476> <Invalid/unknown SSL header was received from peer hostname-osb - x.x.x.x during SSL handshake.>
Traceback (innermost last):
File "<console>", line 1, in ?
File "<iostream>", line 123, in nmConnect
File "<iostream>", line 646, in raiseWLSTException
WLSTException: Error occured while performing nmConnect : Cannot connect to Node Manager. : [Security:090476]Invalid/unknown SSL header was received from peer hostname-osb - x.x.x.x during SSL handshake.
nodemanager.properties file
DomainsFile=/hta/vha/opt/app/osb11R1/wlserver_10.3/common/nodemanager/nodemanager.domains
LogLimit=0
PropertiesVersion=10.3
javaHome=/usr/jdk/instances/jdk1.6.0_21
AuthenticationEnabled=true
NodeManagerHome=/hta/vha/opt/app/osb11R1/wlserver_10.3/common/nodemanager
JavaHome=/usr/jdk/instances/jdk1.6.0_21/jre
LogLevel=INFO
DomainsFileEnabled=true
StartScriptName=startWebLogic.sh
ListenAddress=
NativeVersionEnabled=true
ListenPort=5556
LogToStderr=true
SecureListener=false
LogCount=1
StopScriptEnabled=false
QuitEnabled=false
LogAppend=true
StateCheckInterval=500
CrashRecoveryEnabled=false
StartScriptEnabled=true
LogFile=/hta/vha/opt/app/osb11R1/wlserver_10.3/common/nodemanager/nodemanager.log
LogFormatter=weblogic.nodemanager.server.LogFormatter
ListenBacklog=50
We did following steps to resolve this issue but in vain
S1. Changed Type to 'Plain' from 'SSL' in Machines -> osbMac01 -> Node Manager
S2. Changed SecureListener=true to SecureListener=false in nodemanager.properties
S3. kill the nodemanager and then start.
I guess there is some configuration in nodemanager.properties file that is creating this issue. Can anyone help with the same?
Thanks,
Sameer
Edited by: sameer h on Apr 18, 2011 7:09 PM

SecureListener=falseYou have turned off secure listener for node manager, hence it will accepting 'plain' requests only and cant handle ssl handshakes
nmConnect('weblogic','welcome1','x.x.x.x',5556,'MyOSBDomain')Here you have left the 6th parameter to nmConnect as blank. The default in this case will be ssl and nmConnect is excepting ssl handshake response back from nodemanager, but nm cant reply ssl because it is not enabled.
Solution
1) Turn on Secure Listener = true. Then you can use this exact syntax for nmConnect.
2) Keep secure listener to false. use nmConnect() with all 6 parameters
nmConnect([username, password], [host], [port], [domainName], [domainDir] [nmType])
Pass 'plain' for the nmType attribute
Refer: http://download.oracle.com/docs/cd/E13222_01/wls/docs91/config_scripting/reference.html#1030962

Is anyone using the Calendar Server to send external invites?

Is anyone using the Calendar Server to send external invites?
We have a Mountain Lion server running DNS, Open Directory, File Sharing and VPN. We have recently stood up the Calendar server and it is working very well. Internal invites work fine and are instantaneous to computer, iPhone, iPad. We have the ports working so that calendar items created outside the network work fine as well. Only problem is we cannot invite anyone with an external e-mail address. Each time we do the Calendar Error Log populates with:
2013-04-15 13:11:03-0500 [-] [mailgateway] 2013-04-15 13:11:03-0500 [Uninitialized] SMTP Client retrying server. Retry: 5
2013-04-15 13:11:03-0500 [-] [mailgateway] 2013-04-15 13:11:03-0500 [Uninitialized] SMTP Client retrying server. Retry: 4
2013-04-15 13:11:03-0500 [-] [mailgateway] 2013-04-15 13:11:03-0500 [Uninitialized] SMTP Client retrying server. Retry: 3
2013-04-15 13:11:03-0500 [-] [mailgateway] 2013-04-15 13:11:03-0500 [Uninitialized] SMTP Client retrying server. Retry: 2
2013-04-15 13:11:03-0500 [-] [mailgateway] 2013-04-15 13:11:03-0500 [Uninitialized] SMTP Client retrying server. Retry: 1
2013-04-15 13:11:03-0500 [-] [mailgateway] 2013-04-15 13:11:03-0500 [Uninitialized] [twistedcaldav.mail.MailHandler#error] Mail gateway failed to send message <[email protected]> from [email protected] to mailto:[email protected] (Reason: Failure with multiple causes.)
We have set up an internal e-mail address. I have confined that it works fine. I have tried more than one internal account. I have also verified the settings through the command line by typing "sudo serveradmin settings calendar" The iMIP sending and receiving information is correct. There is no authentication type setting listed in the command line output even though there's a place to choose it in the Enable invitations by email - Edit button on the third screen. No matter what I choose it goes back to "login" and still doesn't work.
The command line settings mention a port number 62310 as being the MailGatewayPort but opening that port on the network's firewall makes no difference. As I said external set up works fine from Mac/iPhone/iPad and push notification works fine as well.
Is anyone using this functionality?

I'm sorry. I forgot to add Mail to the list of services. I AM using mail on that server. Here's the iMIP portion of my settings output from Terminal.
calendar:Scheduling:iMIP:Sending:Server = "boardwalkserver.kuhnwitt.com"
calendar:Scheduling:iMIP:Sending:UseSSL = yes
calendar:Scheduling:iMIP:Sending:Username = "calendarserver"
calendar:Scheduling:iMIP:Sending:Address = "[email protected]"
calendar:Scheduling:iMIP:Sending:Password = "password"
calendar:Scheduling:iMIP:Sending:Port = 465
calendar:Scheduling:iMIP:Enabled = yes
calendar:Scheduling:iMIP:MailGatewayPort = 62310
calendar:Scheduling:iMIP:Receiving:Server = "boardwalkserver.kuhnwitt.com"
calendar:Scheduling:iMIP:Receiving:UseSSL = yes
calendar:Scheduling:iMIP:Receiving:Username = "calendarserver"
calendar:Scheduling:iMIP:Receiving:PollingSeconds = 30
calendar:Scheduling:iMIP:Receiving:Type = "imap"
calendar:Scheduling:iMIP:Receiving:Password = "password"
calendar:Scheduling:iMIP:Receiving:Port = 993
calendar:Scheduling:iMIP:AddressPatterns:_array_index:0 = "mailto:.*"
calendar:Scheduling:iMIP:MailGatewayServer = "localhost"
So Add mail to the services being used. Since Calendar is running on the mail server one would assume that it could communicate with it fairly easily.

Error while subscription on SSRS report that uses custom assembly

I am new to SSRS. i have created a report that uses custom assembly that runs an oracle procedure and bring back result to report. this works fine on sharepoint mode interactive report. while i subscribe the same report, i am getting below error
Request for the permission of type 'System.Data.OracleClient.OraclePermission,System.Data.OracleClient,Version=2.0.0.0,Culture=neutral,PublicKeyToken=b77a5c561934e089'failed. < ==>
at System.Security.CodeAccessSecurityEngine.Check(Objectdemand,StackCrawlMark&stackMark, BooleanisPermSet)
at System.Security.PermissionSet.Demand()
at System.Data.Common.DbConnectionOptions.DemandPermission()
at System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnectionouterConnection,DbConnectionFactoryconnectionFactory)
at System.Data.OracleClient.OracleConnection.Open()
i am breaking my head to find the root cause and fix for this.
i tried adding below permission on server machine.config file,
<SecurityClass Name="OraclePermission" Description="System.Data.OracleClient.OraclePermission, System.Data.OracleClient, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"/>
<PermissionSet class="NamedPermissionSet" version="1" Unrestricted="true" Name="FullTrust" Description="Allows full access to all resources for custom assembly">
<IPermission class="OraclePermission" version="1" Unrestricted="true" Level="High" Flags="FullTrust"/>
</PermissionSet>
it doesnot work and i am getting the same error on subscription.
can anyone help me to solve this issue. this is very urgent. thanks

Can you see data for Custom object @ BEx level??
YES, then just try to re-create the same variable and Save the BW query.
Now do View - refresh Strusture @ Universe. And you can see Filter for the same, just Parse it, just whether it is OK or not.
OK -- then Export the Universe and create WebI reports, this will come as Prompt.
Hope it will helps you.
Thank You!!
Sent from iPhone

PO PDF errors when using custom RTF Template, but works with custom xsl

Hi,
I have done following set up steps for PO PDF
Setup / Organizations / Purchasing Options / Control TAB / set 'PO Output Format' = 'PDF'
setup / purchasing / document types / select "Standard Purchase Order" / Set the Document Type Layout to your new template.
But with the RTF template the PO Output for communication completes with error. However when I use custom XSL-FO style sheet, it works.
Can anyone help me how I can make my RTF work? When click on the preview of the template, it shows the PDF output though. Am I missing any other set up steps? Your help is greatly appreciated.
Thanks,
Sharmila

I think the only way to have control over the html output is to enclose the tags or any information within a borderless table and align the text and table as necessary...
Thanks,
Bipuser

When use custom authetication it shows some characters on screen after logo

Dear All,
I have developed a application and use custom authentication schema for that. It works fine on my local pc and then I have moved it to another pc (export and then import) it works fine on that as well.
Now I have moved it to the production server. When authentication failed it shows error message and stay in log on page. But when I provide the correct user name and password, then it shows multiple occurance of login url in page body.
Did anyone has any idea about this.
When authenticate success I get below output.
Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?
p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?
p=ETLUI:COM_LOGIN:2888953545161107 Location: f?Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?
p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?
p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?
p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?
p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?
p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 Location: f?
p=ETLUI:COM_LOGIN:2888953545161107 Location: f?p=ETLUI:COM_LOGIN:2888953545161107 * ETLUI means my application alias and COM_LOGIN is my login page alias. So basically it shows link to the login screen multiple time. At this time url is looks like below
http://prodsrv:8080/apex/wwv_flow.accept Development and Production Apex Version: 4.0.2.00.07
Development OS: Windows 2000
Production OS : Linux
Thanks in advance.

Works ok after using Apex Listener.

Question about How to Use Custom CellEditors

Hi:
I have been trying to implement something like this: I have a JPanel, and when you double-click a particular spot on it, I want a textbox to appear. Currently, I am implementing it by using an undecorated JDialog that contains a JTextField in it (such that the text field occupies all the space in the dialog, i.e. you can't even tell that there is a dialog). This seems like a hack to me.
Another alternative that I have been thinking about is using layered panes, and hiding the textfield below the jpanel, and only bringing it to the front when the user double-clicks.
Then, I stumbled onto custom celleditors. Now, it seems that everyone is using them in JTables, JLists, JComboBoxes, etc. and I was wondering if it is something that I can use with a JPanel.
Can anyone comment on the implementations I am considering, as well as using custom celleditors with a JPanel?
Thanks in advance,
LordKelvan

Still don't understand your requirement. Does the text field stay there or disappear after the data is entered? If it disappears, then how do you change the value, do you have to click on the exact same pixel again?
Maybe you could use a MouseListener and then display a JOptionPane or JDialog to prompt for the information. Or if you want to display a JTextField then add a JTextField to the panel and then when the user enters the data by using the enter key or by clicking elsewhere on the GUI you remove the text field from the panel.

Email Alert Template Issue - List Alerts (Alert Me) emails not using customized XML alert template

We have recently customized the XML alerts template (AlertTemplates.xml) for our site collection in SharePoint 2010 to exclude specific fields in the email when users who have subscribed using the "Alert Me" feature. We have renamed the
custom alerts XML file and loaded the custom template in the following directory (%ProgramFiles%\Common Files\Microsoft Shared\Web server extensions\14\TEMPLATE\XML) and restarted IIS. Once users subscribe to the alerts using the list "alert me"
function they received the customized email as intended.
We needed to auto-subscribe users to the email alerts so what we did was use a powershell script to add users to the alert subscriptions using the script shown below:
Import-Csv D:\Temp\filename.csv | ForEach-Object{
$webUrl=$_.WebUrl
$listTitle=$_.List
$alertTitle=$_.AlertTitle
$subscribedUser=$_.SubscribedUser
$alertType=$_.AlertType
$deliveryChannel=$_.DeliveryChannel
$eventType=$_.EventType
$frequency=$_.Frequency
$oldAlertID=$_.ID
$web=Get-SPWeb $webUrl
$testAlert = $web.Alerts | WHERE { $_.ID -eq $oldAlertID }
IF ($testAlert) {
$web.Alerts.Delete([GUID]$oldAlertID)
Write-Host Old alert $oldAlertID deleted. -Foregroundcolor Cyan
$list=$web.Lists.TryGetList($listTitle)
$user = $web.EnsureUser($subscribedUser)
$newAlert = $user.Alerts.Add()
$newAlert.Title = $alertTitle
$newAlert.AlertType=[Microsoft.SharePoint.SPAlertType]::$alertType
$newAlert.List = $list
$newAlert.DeliveryChannels = [Microsoft.SharePoint.SPAlertDeliveryChannels]::$deliveryChannel
$newAlert.EventType = [Microsoft.SharePoint.SPEventType]::$eventType
$newAlert.AlertFrequency = [Microsoft.SharePoint.SPAlertFrequency]::$frequency
if($frequency -ne "Immediate"){
$AlertTime=$_.AlertTime
$newAlert.AlertTime=$AlertTime
$newAlert.Update()
Write-Host Created $newAlert.Title for $subscribedUser . -Foregroundcolor Cyan
} ELSE {
Write-Host Alert $alertTitle for $subscribedUser already done. Moving on. -Foregroundcolor Magenta
When we ran the script and added the users and restarted the service, all users who were auto-subscribed via this method get the email without the customizations that were done in teh custom alert template. All users who manually subscribed on their
own to the list using the "Alert Me" function would get the customized email.
Does anyone know why users who manually subscribe to the alerts get the customized email, and users who were auto-subscribed using the powershell script do not get the customized email and get the standard generic email template?

Hi ,
According to your code, it create a new alert using SPUser.Alerts.Add() method. For this method, it will create a new alert based on the predefined alert template by default.
If you only assigned the custom alert template to the list, users who manually subscribe to the alerts get the customized email, but users who were auto-subscribed using the PowerShell script get the standard
generic email template.
For your issue, you can set the new alert ‘s alert template:
http://social.technet.microsoft.com/Forums/en-US/1b19c12f-fc37-48cf-8b59-6c09f095dc23/custom-alert-email-templates-issue-list-alerts-emails-not-using-customized-xml-alert-template?forum=sharepointgeneralprevious
Here is a good blog you can have a look:
http://blogs.msdn.com/b/sharepointdeveloperdocs/archive/2007/12/07/customizing-alert-notifications-and-alert-templates-in-windows-sharepoint-services-3-0.aspx
Thanks,
Eric
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support,
contact [email protected]
Eric Tao
TechNet Community Support

My privacy setting is stuck on Remember history, won't stay on Use custom settings for history after I set and click ok

When I go into Tools, Options, Privacy and set 'Use custom settings for history' and then click okay it will not save. It stays on 'Remember history', though it will save 'Never remember history' as I tested this. This seems to have happened after recent Firefox latest update. Does anyone know why I can't choose 'Use custom settings for history' as this is the setting I want to use?

It's not that I'm not satisfied with the current settings, it's just that I'm one of those curious people - wanting to know why suddenly I couldn't change my history setting when I could always chop and change it before to a setting of my choice. I noticed this has happened since recently updating to Firefox 6. When things like this just happen I always search for a reason. Anyway, it sounds as though I am a bit of a novice on Firefox compared to yourself, and if you recommend that it's probably best to stay on Remember History and it's not likely to cause any problems, then say no more, I shall accept your advice. Any more tips would be greatly appreciated! Thanks.

Anyone using a 4K monitor with FCP X?

Is anyone using FCP X on a 4K monitor? I'm thinking about getting a Dell 4K monitor as my main monitor but I'm a little worried the user interface support on 4K is weak. I think everything is going to look super tiny.
Has anyone already experienced this?
Thanks!

So I have my new Mac Pro set up. 8-Core, 32 gigs RAM, Dual 700 GPUs, 512 gig internal Flash drive.
I purchased the 27" Thunderbolt display as my main Final Cut Pro X screen and I have the Dell UP2414q 4K monitor plugged in as the Viewer display.
I have the Dell set to "Best for Display" and it works fine. I have some 4480 x 1920 RED footage and I have the FCP X Viewers on the Dell. The footage is set to 100% and it bleeds a little off the sides, as it should since the monitor is 3820 wide. It's at its native resolution.
The user interface elements of the second monitor are at normal size - the menu bar, the FCP X view options. Buying a 4K monitor and using Best for Display gives you the desktop the size of a typical 1080 monitor, but it all looks like a Retina display. It's very crisp.
So if you want a second monitor to hold a ton of Adobe palettes, and have a very large desktop, I'd recommend getting a Thunderbolt display, beause this display behaves like a 1080 monitor in that regard. If you want a 4K monitor specifically for color grading 4K footage at the native size so you can see all the artifacts and things you wouldn't see with the footage at 50%, this Dell monitor is fine and it's $890 on Amazon. It's not a professional color grader's monitor, obviously, but it does well for me.
I took some 4480 x 1920 RED footage that had a sky that was gray (the famous Mercedes in the mountains footage). I used the color picker color correction in FCP X and was able to select that sky very easily. I can see why the fat 4K footage is so great in regards to color grading. Because you don't have the massive color gradiation and artifacts you get in the more compressed media, when you use the color picker, it selects a very large, clean, section of the sky. I was able to quickly make the sky more saturated and blue and play it in real time (Better Performance) it's it's perfectly clean with no halos around the tree branches as they move into the foreground of the sky. Very nice!
Nice feature in FCP X is all the effects, transitions, etc., have a "4K-ready content only" button at the top so it only presents you with effects and transitions that work with 4K footage.
It took a lot of time calibrating this Dell monitor. It has the Adobe RGC color space built in but when I set it to that and set the OS X Display color option to Adobe RGB, it all had a very slight purple/pink huge. Very slight. Whites were not pure white like they are on the Thunderbolt and my blue sky had a tinge of pink to it.
I calibrated it with advanced options in the OS X Display preferences. I then connected my Samsung HD LED TV into the HDMI port of the Mac Pro and set it as my A/V display in FCP X. I was able to do the custom color setting on the Dell monitor itself and lower the saturation and RGB values. It took about 15 minutes to get it looking right. Now, I don't see the very slight purple/pink tink. My blue sky looks blue, etc., and it looks exactly how it will look on DVD and Blu-ray and projectors at film festivals.
The Samsung LED TV was a breeze to use. As soon as I plugged it into the HDMI port of the Mac Pro, the displays changed and OS X went to 1920 x 1080 60hz. The color was set to an HD color preset (I forget the number and I disconnected it). Arranging the multiple monitors is as you'd expect, just works.
BTW, I have 2 10 TB 5Big Lacie Thunderbolt 2 hard drives. They are about $1K each at 10 TBs. I have one for my footage and one as a backup with Time Machine. No formatting necessary - just plug them in and go. I plugged in the first one, told OS X no for Time Machine. Plugged in the second one, told Time Machine yes. Renamed the second drive "Backup". I turned off hard drive sleep becuase it's annoying. You hear it spin up, spin down, spin up, etc. as you work.
I used the AJA benchmark and this is what I got with 16 gig test file, 4K video simulation:
Write 740.3 MB/s
Read: 849.1 MB/s
Fast!
FCP X loads in 4 seconds on this system off the internal Flash drive.
Cheers!

How do I...Mimic Replacement Path with Query using Customer Variable Exits?

Hello SDN:
We are on BW 3.5 SP16.
We are currently using a replacement path Query(RP) with variables
to populate a variable in another Query(T).
The problem we are having is with performance.
The entry of variables in replacement path Query(RP) is optional (This is necessary there cannot be required values)
When results from Replacement Path Query are small performance is fine. (e.g. 10 seconds)
When results from Replacement path query are large performance suffers. (e.g. 1+ minutes)
Users are free to leave the replacement path variables empty resulting in a large set of data to be replaced. This is the worst performance case.
We would like to discover a way to conditionally execute the replacement path query. That is if users do not enter values for the replacement Query(RP) variables do not execute the replacement path query(RP).
Does anyone know if this is possible within reason and in customer exit space?
We have reviewed the situation from all angles and the requirement for the replacement path FUNCTIONALITY and the freedom for the user to leave variable values blank remains.
I've been searching and reading SDN and SAP notes for about a week and do not find threads which address this situation.
We are also exploring Customer variable exits to mimic replacement path functionality
(different topic subject="How do I...Mimic Replacement Path with Query using Customer Variable Exits?")
Any help will be appreciated
Many thanks
David Schuh

My appologies-I posted this message with the wrong subject. I will repost it with appropriate subject.
dave schuh

Is anyone using a 1252 ap in bridge mode with channel bonding?

Is anyone using a 1252 ap in bridge mode, with channel bonding?
I had a question a while ago from a customer with regards to bridging with a 1252 ap to increase throughput for a wireless link he was using, from the throughput improvements in 802.11n. At the time I spoke to Cisco Pre-Sales, and they indicated that the bridge function in the 1252 exists for 'testing' purposes. I advised our customer that although it should be possible to implement, we may run into difficulties with TAC support ect. in the event of problems with the link.
Can anyone comment if this is a Cisco validated/approved design now?
Also, has anyone done this and tested the throughput achievable?
Has anyone bridged both 2.4Ghz and 5Ghz radios on a 1252?
The reason I ask is I've seen a note about a Cisco 5Ghz 802.11n bridge being launched.
Thanks in advance.
Alex.

Hi All,
Thanks for all the feedback; I have finally done some throughput testing with the 1252's. Please note, this is very rough, just to give an idea on throughput that's achievable, and what you can enable. Did this a few weeks back, and have now wiped the cnf, so dont have the show runs any more....
The two devices were set up a few feet apart, with the standard 2dBi and 3dBi antenna.
All tests done on the 5GHz radio with Autonomous AP IOS.
I did data transfers via a laptop either end of the link; transferring data using the Test TCP utility (wasn't going for scientific tests, just getting some idea of throughput).
802.11a @ 54mbs (20Mhz chan) WGB - root to non root = 2.43 - 2.5MB/Sec = 19.44 - 20 Mbps
802.11a @ 54mbs (20Mhz chan) WGB non root to root = 2.42 - 2.44MB/Sec = 19.44 - 20 Mbps
802.11n @ 'n' rates( 20Mhz chan) WGB root to non root = 6.18 - 6.33MB/Sec = 49.44 - 50.64 Mbps
802.11n @ 'n' rates ( 20Mhz chan) WGB non root to root = 4.77 - 5.00MB/Sec = 38.16 - 40 Mbps
802.11n @ 'n' rates ( 40Mhz chan) WGB root to non root = 8.59 - 8.58MB/Sec = 68.64 - 68.64 Mbps
802.11n @ 'n' rates ( 40Mhz chan) WGB non root to root = 6.35 - 7.20MB/Sec = 50.8 - 57.6 Mbps
802.11n @ 'n' rates ( 40Mhz chan) Bridge root to non root = 9.73 - 10MB/Sec = 77.84 - 80 Mbps
802.11n @ 'n' rates ( 40Mhz chan) Bridge non root to root = 8.40 - 8.57MB/Sec = 67.2 - 68.56 Mbps
So basically, as per the above posts, you can implement bridging on the 1252's and utilise the 802.11n rates and features, SGI, Spatial Streams and Channel Bonding etc, to achieve higher throughput.
Also, as per the above posts, this is still not supported by Cisco, so, in my case, I'd be highlighting that to customers straight off, but don't see it as too much of an impediment to deploy, as long as the customer weighs up the risks.
On a side note, I attended a Cisco session recently, and was told that the 802.11n Bridge, (the 1430?) was on hold indefinitely. My feeling is that this makes it more pressing that Cisco introduces support for bridging on the 1252.
Get in the ear of your local Wireless SE's, the more they hear it, the more they'll moan to the Wireless BU in San Jose! ;-)
Bridging with 802.11n has some interesting possibilities, I worked with Alvarion 5GHz bridges 6 or 7 years ago, that could do 'near LOS' - Worked well in cities, using reflection of the RF from buildings. I had never heard of 802.11n back then, but I'm guessing Alvarion was using MIMO to achieve good non-LOS connectivity in the 5GHz band.
Cheers,
Alex.

How to make Custom Discoverer workbook use Custom Security profile of Apps

We use Discoverer in Oracle Apps setup. We have added Custom security in our HR People Form of Apps.
This Custom Security restricts one HR Emplpoyee not view other HR employee record except for himself/herself. Also maintining that they should be able to view all other employee's records.
The following code was put under the Security Profile Form -- > Custom Security Tab
exists (select 1
from per_jobs b
where ASSIGNMENT.job_id = b.job_id
and (b.name not like '%HR%')
and (b.name not like '%Human%')
and ASSIGNMENT.assignment_number is not null
union
select 1
from fnd_user fu
where fu.user_name = fnd_global.user_name
and fu.employee_id = PERSON.person_id
and ASSIGNMENT.assignment_number is not null)
Above security profile works fine for HR People Form.
However, It does not work for our Discoverer Workbooks. I found a note on Metalink 422841.1 which talks about leveraging the Custom Security of Apps in Discoverer Report. I read it, but did not get much clue.
Can Anyone help.
Thanks

Hi,
If you want to use custom HR security with Discoverer you have to ensure that the correct security filters are applied when the Discoverer reports are run. These filters can use the supplied HR_SECURITY package or you can develop your own conditions using table lookups or functions. To get the filters applied to your reports you have a number of options:
1. Build the security into custom folders using additional conditions
2. Use custom database views in Discoverer and build the security into the views
3. Use mandatory conditions in you Discoverer folders using either a function call or database contexts set at login time
4. Use VPD (Virtual Private Database)
I am not sure which of these options you are using to implement your HR security in Discoverer. The last option, VPD, is the most flexible and can give the best performance but maybe it is more complex to set up.
Rod West

Crystal Reports with BEx Query using Custom Exit Variable

Hi,
We have BW BEx Query using Customer User Exit variable to derive the Fiscal Week for Last Year (called it VAR2) based on another user input variable Current Fiscal Week (called it VAR1).
VAR2 is derived from VAR1 in CMOD via some codings and thus it DOES NOT have the "Variable is Ready for Input" flag ticked in the BEx. VAR1 is user input variable, so it has "Variable is Ready for Input" flag ticked in the BEx.
When we create a Crystal Reports with the BEx Query using variable VAR2, and when we run it we got an error message saying "Failed to execute query; '[]<java.lang.UnsupportedOperationException: No Selection State Support!ZP_MI_LYPUBWEEK>'. Redesign your query or contact the data source maintainer to solve the problem". (note: ZP_MI_LYPUBWEEK is VAR2 in this case).
Could anyone please assist? Surely, CR supports BEx customer user exit variables like the above, right?. I also refer to the forum below as it seems to have a similar issue (except mine with an error message), but it does not provide a solution in it.
Crystal Reports with BEx Query using Custom Exit Variable
Thanks,
Andy

Hi Vibhav,
We have the SAP Crystal Reports for Enterprise XI4.0 Version 14.0.0. Not sure if SP0 or other SP, got to check with Basis Team later.
We tried that "mandatory" option and did not work either.
Anyway, SAP has now come back again saying it is something they will fix it in next release/version. We got a phone call from them and a reply below to our OSS.
23.08.2011 - 08:20:49 CET - Info for Customer by SAP
I have raised this issue on the Idea#s Place as an enhancement request
on the below link:
https://cw.sdn.sap.com/cw/ideas/5586
This ER contains the information of including the customer exit
variables in the report without checking the #input for ready# option.
This ER can be considered for being implemented in the future
versions. You can refer to SAP Note: 1515837 - How To: Enhancement
Request Process - "Idea Place" for more information regarding the Idea
Place.
Cheers,
Andy

Using Custom Attributes in HBR

<p>Does anyone know how to use custom attributes to limit local orglobal HBR variables (run-time prompts)? We have business rulesthat were developed in the graphical designers and the run timeprompt was set up to limit the user's selection based on a customattribute. When these business rules are imported into EAS theywill no longer validate.</p>

Hi Maarten,
I have applied the logic mentioned above to my code. But it still does not procure any data from the container.
<ItemType name="uwl.task.webflow.decision.<task>" connector="WebFlowConnector" defaultView="travel" defaultAction="launchTravelUwl" executionMode="default">
      <ItemTypeCriteria systemId="UWL_R3" externalType="<task>" connector="WebFlowConnector"/>
       <CustomAttributes>
        <CustomAttributeSource id="ABAP_BOR" objectIdHolder="NOTIFICATION" objectType="ZBUS2078" cacheValidity="final">
          <Attribute name="STARTDATE" type="date" displayName="Creation Date"/>
          <Attribute name="ENDDATE" type="double" displayName="Due By"/>
        </CustomAttributeSource>
        <CustomAttributeSource id="WEBFLOW_CONTAINER" objectIdHolder="NOTIFICATION" objectType="WebflowContainer" cacheValidity="final">
          <Attribute name="NOTIFICATION" type="string" displayName="NOTIFICATION"/>
        </CustomAttributeSource>
      </CustomAttributes>
      <Actions>
        <Action name="replan" groupAction="no" handler="UserDecisionHandler">
          <Properties>
            <Property name="UserDecisionNote" value="mandatory"/>
            <Property name="decisionKey" value="4"/>
          </Properties>
        </Action>
        <Action name="reject" groupAction="yes" handler="UserDecisionHandler">
          <Properties>
            <Property name="UserDecisionNote" value="true"/>
            <Property name="decisionKey" value="1"/>
          </Properties>
        </Action>
      </Actions>
    </ItemType>

UCCE - JTAPI gateway - anyone using custom JavaRunTimeOptions ?

Similar Messages

Maybe you are looking for