Unable to initialize logging infrastructure for localization

I think this might be trouble:
After patching LMS 3.2 up, I checked Syslog Collector status. It *looked* fine, except every number is zero across the board. Toggling subscription on/off did nothing. I see an old thread with a similar issue that indicates TAC assistance with DB queries to fix config archive unique IDs is needed. Barring that, would I be able to recover by simply restoring a copy of the old LMS backup?
Forwarded
Invalid
Filtered
Dropped
Received
Up Time
Update Time
1.
nms.fqdn.com
0
0
0
0
0
Feb 25 2010 02:22:00 Eastern Standard Time(GMT -05:00:00)
Feb 25 2010 02:28:49 Eastern Standard Time(GMT -05:00:00)
tail -f SyslogAnalyzerUI.log
[ Wed Feb 24 18:19:38 EST 2010 ],INFO ,[TP-Processor6],com.cisco.nm.rmeng.common.VerifyRMELicense,validate,?,INFO: Resource Limit from License file=1500
[ Wed Feb 24 18:19:38 EST 2010 ],INFO ,[TP-Processor6],com.cisco.nm.rmeng.common.VerifyRMELicense,validate,?,
[ Thu Feb 25 02:10:42 EST 2010 ],ERROR,[TP-Processor1], Unable to initialize logging infrastructure for localization
[ Thu Feb 25 02:10:43 EST 2010 ],ERROR,[TP-Processor1],No resource is associated with key "Unable to initialize logging infrastructure for localization".
[ Thu Feb 25 02:10:43 EST 2010 ],ERROR,[TP-Processor1],Unable to initialize logging infrastructure for localization
I did a full dmgtd restart, but there's no new entry in SyslogAnalyzerUI.log:

tail -f AnalyzerDebug.log
[ Thu Feb 25 02:21:45 EST 2010 ],INFO ,[main],newsyslogqueue queue created with max size 100000
[ Thu Feb 25 02:21:45 EST 2010 ],INFO ,[main],processorsyslogqueue queue created with max size 100000
[ Thu Feb 25 02:21:45 EST 2010 ],INFO ,[main],Queue for new incoming syslogs created with size 100000
[ Thu Feb 25 02:21:45 EST 2010 ],INFO ,[main],Queue for action processor created with size 100000
[ Thu Feb 25 02:21:55 EST 2010 ],INFO ,[main],Action processors created
[ Thu Feb 25 02:21:55 EST 2010 ],INFO ,[main],Action processors created
[ Thu Feb 25 02:21:55 EST 2010 ],INFO ,[main],Action processors created
[ Thu Feb 25 02:21:55 EST 2010 ],INFO ,[main],Action processors created
[ Thu Feb 25 02:21:55 EST 2010 ],INFO ,[main],Action processors created
[ Thu Feb 25 02:22:00 EST 2010 ],INFO ,[main],Service started...
tail -f SyslogCollector.log
SyslogCollector - [Thread: main] INFO , 25 Feb 2010 02:01:14,930, Logging System Initialized.
SyslogCollector - [Thread: main] INFO , 25 Feb 2010 02:01:14,932, System Initialized.
SyslogCollector - [Thread: main] INFO , 25 Feb 2010 02:01:14,962, Queue Cap 100000
SyslogCollector - [Thread: main] WARN , 25 Feb 2010 02:01:17,330, Unable to resurrect connection to a subscriber.
SyslogCollector - [Thread: main] INFO , 25 Feb 2010 02:01:17,376, Service started...
SyslogCollector - [Thread: main] INFO , 25 Feb 2010 02:17:19,644, Logging System Initialized.
SyslogCollector - [Thread: main] INFO , 25 Feb 2010 02:17:19,646, System Initialized.
SyslogCollector - [Thread: main] INFO , 25 Feb 2010 02:17:19,666, Queue Cap 100000
SyslogCollector - [Thread: main] WARN , 25 Feb 2010 02:17:21,947, Unable to resurrect connection to a subscriber.
SyslogCollector - [Thread: main] INFO , 25 Feb 2010 02:17:21,993, Service started...
tail -f SyslogAnalyzerUI.log
repositories:
/WEB-INF/classes/
----------> Parent Classloader:
org.apache.catalina.loader.StandardClassLoader@170bea5
[ Wed Feb 24 18:19:38 EST 2010 ],INFO ,[TP-Processor6],com.cisco.nm.rmeng.common.VerifyRMELicense,validate,?,INFO: Resource Limit from License file=1500
[ Wed Feb 24 18:19:38 EST 2010 ],INFO ,[TP-Processor6],com.cisco.nm.rmeng.common.VerifyRMELicense,validate,?,
[ Thu Feb 25 02:10:42 EST 2010 ],ERROR,[TP-Processor1], Unable to initialize logging infrastructure for localization
[ Thu Feb 25 02:10:43 EST 2010 ],ERROR,[TP-Processor1],No resource is associated with key "Unable to initialize logging infrastructure for localization".
[ Thu Feb 25 02:10:43 EST 2010 ],ERROR,[TP-Processor1],Unable to initialize logging infrastructure for localization

Similar Messages

About unable to initialize log file!

Hi,
I insatll the Sun Java communications suite 5 in one linux host.
When I restart web server, I got the following error, would you please give me a hand ?
Thank you in advance.
*# /var/opt/sun/webserver7/https-comms.swabplus.com/bin/stopserv*
server has been shutdown
*# /var/opt/sun/webserver7/https-comms.swabplus.com/bin/startserv*
Sun Java System Web Server 7.0 B12/04/2006 08:17
warning: CORE3283: stderr: Java HotSpot(TM) Server VM warning: Can't detect initial thread stack location - find_vma failed+_
info: CORE5076: Using [Java HotSpot(TM) Server VM, Version 1.5.0_09] from [Sun Microsystems Inc.]
info: WEB0100: Loading web module in virtual server [com5.my.com] at [amserver]
warning: WEB6100: locale-charset-info is deprecated, please use parameter-encoding
info: WEB0100: Loading web module in virtual server [com5.my.com] at [ampassword]
warning: WEB6100: locale-charset-info is deprecated, please use parameter-encoding
info: WEB0100: Loading web module in virtual server [com5.my.com] at [amcommon]
warning: WEB6100: locale-charset-info is deprecated, please use parameter-encoding
info: WEB0100: Loading web module in virtual server [com5.my.com] at [amconsole]
warning: WEB6100: locale-charset-info is deprecated, please use parameter-encoding
info: WEB0100: Loading web module in virtual server [com5.my.com] at [da]
info: WEB0100: Loading web module in virtual server [com5.my.com] at [commcli]
info: url: jar:file:/opt/sun/mfwk/share/lib/mfwk_instrum_tk.jar!/com/sun/mfwk/config/MfConfig.class
info: url: jar:file:/opt/sun/mfwk/share/lib/mfwk_instrum_tk.jar!/com/sun/mfwk/config/MfConfig.class
info: LogFile is: //var/opt/sun/mfwk/logs/instrum.%g_
warning: Warning: unable to initialize log file!+_
warning: Couldn't get lock for //var/opt/sun/mfwk/logs/instrum.%g+_
info: group = 227.227.227.1, port = 54320
info: Set Time-to-live to 0
info: join Group /227.227.227.1
info: Starting listening thread
info: sends initial RESP message in SDK
info: HTTP3072: http-listener-1: http://com5.my.com:80 ready to accept requests
info: CORE3274: successful server startup

This happens when you install web server as "non-root" and start the instance as "root".
If you can avoid this, you can get around of
warning: CORE3283: stderr: Java HotSpot(TM) Server VM warning: Can't detect initial thread stack location - findvma failed_*
The cause for log file initialization problem appears to be some permission problem.
Can you get back once you take care of what suggested above.

JDeveloper 12.1.3 is unable to initialize OC4J Server for OAF

Dear All,
I am facing an issue with my jDeveloper.
Details
=============
OS: Windows 7 Ultimate (64-Bit)
Apps: Oracle Apps 12.1.3
Hardware: HP Pavilion G4 with 4gb RAM (64-Bit Processor)
jDeveloper Version: 10.1.3.3.0
Connecting to Apps Instance via VPN Access (Instance and SQL Developer runs fine)
Error Log - OC4J
============
[Starting OC4J using the following ports: HTTP=8988, RMI=23891, JMS=9227.]
C:\jDev\jDev12.1.3\jdevhome\jdev\system\oracle.j2ee.10.1.3.41.57\embedded-oc4j\config>
C:\jDev\jDev12.1.3\jdevbin\jdk\bin\javaw.exe -hotspot -classpath C:\jDev\jDev12.1.3\jdevbin\j2ee\home\oc4j.jar;C:\jDev\jDev12.1.3\jdevbin\jdev\lib\jdev-oc4j-embedded.jar -DFND_JDBC_STMT_CACHE_SIZE=200 -DCACHENODBINIT=true -DRUN_FROM_JDEV=true -mx256m -XX:MaxPermSize=256M -Doracle.j2ee.dont.use.memory.archive=false -Xverify:none -DcheckForUpdates=adminClientOnly -Doracle.application.environment=development -Doracle.j2ee.http.socket.timeout=500 -Doc4j.jms.usePersistenceLockFiles=false oracle.oc4j.loader.boot.BootStrap -config C:\jDev\jDev12.1.3\jdevhome\jdev\system\oracle.j2ee.10.1.3.41.57\embedded-oc4j\config\server.xml
[waiting for the server to complete its initialization...]
Aug 28, 2012 12:00:52 PM com.evermind.server.jms.JMSMessages log
INFO: JMSServer[]: OC4J JMS server recovering transactions (commit 0) (rollback 0) (prepared 0).
Aug 28, 2012 12:00:52 PM com.evermind.server.jms.JMSMessages log
INFO: JMSServer[]: OC4J JMS server recovering local transactions Queue[jms/Oc4jJmsExceptionQueue].
WARNING: Code-source C:\jDev\jDev12.1.3\jdevbin\jdev\appslibrt\xml.jar (from <library> in /C:/jDev/jDev12.1.3/jdevhome/jdev/system/oracle.j2ee.10.1.3.41.57/embedded-oc4j/config/application.xml) has the same filename but is not identical to /C:/jDev/jDev12.1.3/jdevbin/lib/xml.jar (from <code-source> (ignore manifest Class-Path) in META-INF/boot.xml in C:\jDev\jDev12.1.3\jdevbin\j2ee\home\oc4j.jar). If it contains different versions of the same classes, it will be masked as the latter is already visible in the search path of loader default.root:0.0.0.
WARNING: Code-source C:\jDev\jDev12.1.3\jdevbin\jdev\appslibrt\jazn.jar (from <library> in /C:/jDev/jDev12.1.3/jdevhome/jdev/system/oracle.j2ee.10.1.3.41.57/embedded-oc4j/config/application.xml) has the same filename but is not identical to /C:/jDev/jDev12.1.3/jdevbin/j2ee/home/jazn.jar (from <code-source> in META-INF/boot.xml in C:\jDev\jDev12.1.3\jdevbin\j2ee\home\oc4j.jar). If it contains different versions of the same classes, it will be masked as the latter is already visible in the search path of loader default.root:0.0.0.
WARNING: Code-source C:\jDev\jDev12.1.3\jdevbin\jdev\appslibrt\jazncore.jar (from manifest of /C:/jDev/jDev12.1.3/jdevbin/jdev/appslibrt/jazn.jar) has the same filename but is not identical to /C:/jDev/jDev12.1.3/jdevbin/j2ee/home/jazncore.jar (from <code-source> in META-INF/boot.xml in C:\jDev\jDev12.1.3\jdevbin\j2ee\home\oc4j.jar). If it contains different versions of the same classes, it will be masked as the latter is already visible in the search path of loader default.root:0.0.0.
WARNING: Code-source C:\jDev\jDev12.1.3\jdevhome\jdev\system\oracle.j2ee.10.1.3.41.57\embedded-oc4j\applications\datatags\webapp\WEB-INF\lib\uix2.jar (from WEB-INF/lib/ directory in C:\jDev\jDev12.1.3\jdevhome\jdev\system\oracle.j2ee.10.1.3.41.57\embedded-oc4j\applications\datatags\webapp\WEB-INF\lib) has the same filename but is not identical to /C:/jDev/jDev12.1.3/jdevbin/jdev/appslibrt/uix2.jar (from <library> in /C:/jDev/jDev12.1.3/jdevhome/jdev/system/oracle.j2ee.10.1.3.41.57/embedded-oc4j/config/application.xml). If it contains different versions of the same classes, it will be masked as the latter is already visible in the search path of loader datatags.web.webapp:0.0.0.
12/08/28 12:01:21 java.net.ConnectException: Connection timed out: connect
12/08/28 12:01:21 at java.net.TwoStacksPlainSocketImpl.socketConnect(Native Method)
12/08/28 12:01:21 at java.net.AbstractPlainSocketImpl.doConnect(AbstractPlainSocketImpl.java:339)
12/08/28 12:01:21 at java.net.AbstractPlainSocketImpl.connectToAddress(AbstractPlainSocketImpl.java:200)
12/08/28 12:01:21 at java.net.AbstractPlainSocketImpl.connect(AbstractPlainSocketImpl.java:182)
12/08/28 12:01:21 at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:157)
12/08/28 12:01:21 at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:391)
12/08/28 12:01:21 at java.net.Socket.connect(Socket.java:579)
12/08/28 12:01:21 at java.net.Socket.connect(Socket.java:528)
12/08/28 12:01:21 at java.net.Socket.<init>(Socket.java:425)
12/08/28 12:01:21 at java.net.Socket.<init>(Socket.java:241)
12/08/28 12:01:21 at oracle.jdevimpl.runner.oc4j.Oc4jNotifier.sendMessage(Oc4jNotifier.java:98)
12/08/28 12:01:21 at oracle.jdevimpl.runner.oc4j.Oc4jNotifier.postInitApplicationServer(Oc4jNotifier.java:55)
12/08/28 12:01:21 at com.evermind.server.ApplicationServer.serverExtensionPostInit(ApplicationServer.java:1202)
12/08/28 12:01:21 at com.evermind.server.ApplicationServer.setConfig(ApplicationServer.java:1049)
12/08/28 12:01:21 at com.evermind.server.ApplicationServerLauncher.run(ApplicationServerLauncher.java:131)
12/08/28 12:01:21 at java.lang.Thread.run(Thread.java:722)
12/08/28 12:01:21 Oracle Containers for J2EE 10g (10.1.3.3.0) initialized
========== End of Error Log ================================
As per instructions, I have set JDEV_USER_HOME path, created new connection for connecting to Apps Instance. Connection test log show "success" message. I am able to load and compile toolbox.jws project. But at time of running HomePG.xml or any other file, I get exception mentioned above.
So far, I have tried below mentioned steps to resolve this issue but unable to resolve it.
1. Connecting to separate instance.
2. Reconfiguring jDev (all steps again)
3. Change to use Full Host Name, Host Short Name or IP Address in OC4J Preferences.
4. New DBC File for instance
5. Replace JDK 1.5.0 with JDK 1.7
6. Re-installing JDeveloper from C: to D:
Please help me resolve this issue.
Thanks and Regards,
Saurabh

There is some problem with your WSDL.
Share your wsdl content here.
Looks like some problem with your operation definition with input and output variable definitions.
Thanks,
Vijay

In HTTP log: Store Critical: Unable to read index file for user/ uid

All:
Sun Java(tm) System Messaging Server 6.2-7.05 (built Sep 5 2006)
libimta.so 6.2-7.05 (built 12:18:44, Sep 5 2006)
We recently have started to see the following errors in our http logs:
[01/Mar/2007:13:03:43 -0500] httpd[5174]: Store Critical: Unable to read index file for user/<uid>: System I/O error. Administrator, check server log for details.
It's occurring a couple of different times during the day to certain users. Then it won't happen for days to anyone, but then start up again. I saw a similar thread to this re: IMAP and I'm curious if http could be having the same problem. We increased the number of process of http (from 2 to 4 a few months ago) but kept the same maxsessions (6000), so maybe I need to change the maxsession to something lower? We only started to see the I/O error two weeks ago We're not seeing the error in imap logs. Also there's no errors in the default log related to the users that receive this in http.
I'm planning on running a reconstruct -m in the mean time to see if that helps. There have been no changes to the server or application for quite some time. Any thoughts?

Yes, http can have the same issue. Yes, lowering the maxsessions from 6000 is the answer, IF it's the same problem. Likely, but not guranteed.
If you actually look at the store.idx for that particular user, what do you see? Is it near 2 gig? If so, then the user needs to either delete some messages or move some to another folder, as 2 gig is the limit for the store.idx file.....
jay

I can not log onto PS Message;Unable to start your subscription for Adobe PS cc

I can not log onto PS Message;Unable to start your subscription for Adobe PS cc

Sign out of the Creative Cloud Desktop app, restart your computer, log in again, and restart Photoshop.
Benjamin

Error while installing exchange2007 : Unable to initialize the Microsoft Exchange Information Store service. Failed to find the

Hi,
I am trying fresh install of exchange2007, everything gone well but, finally it thrown a error saying :
Unable to initialize the Microsoft Exchange Information Store service. Failed to find the working directory parameter from the registry - Error 0x80004005.
the installation log says
6/5/2007 3:14:05 PM] [1] Processing component 'Mailbox Service Control (Last)' (Starting mailbox services).
[6/5/2007 3:14:05 PM] [1] Executing 'start-SetupService -ServiceName MSExchangeIS -MaximumWaitTime "unlimited"', handleError = False
[6/5/2007 3:14:05 PM] [2] Launching sub-task '$error.Clear(); start-SetupService -ServiceName MSExchangeIS -MaximumWaitTime "unlimited"'.
[6/5/2007 3:14:05 PM] [2] Beginning processing.
[6/5/2007 3:14:05 PM] [2] The maximum wait for the operation is set to 'unlimited'.
[6/5/2007 3:14:05 PM] [2] Service checkpoint has progressed. Previous checkpoint='0' - Current checkpoint='1'.
[6/5/2007 3:14:05 PM] [2] Will wait '10000' milliseconds for the service 'MSExchangeIS' to reach status 'Running'.
[6/5/2007 3:14:15 PM] [2] Service 'MSExchangeIS' failed to reach status 'Running' on this server after waiting for '10000' milliseconds.
[6/5/2007 3:14:15 PM] [2] Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [2] [ERROR] Unexpected Error
[6/5/2007 3:14:15 PM] [2] [ERROR] Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [2] Ending processing.
[6/5/2007 3:14:15 PM] [1] The following 1 error(s) occurred during task execution:
[6/5/2007 3:14:15 PM] [1] 0. ErrorRecord: Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [1] 0. ErrorRecord: Microsoft.Exchange.Configuration.Tasks.ServiceFailedToStartException: Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [1] [ERROR] Service 'MSExchangeIS' failed to start. Check the event log for possible reasons for the service start failure.
[6/5/2007 3:14:15 PM] [1] Setup is halting task execution because of one or more errors in a critical task.
[6/5/2007 3:14:15 PM] [1] Finished executing component tasks.
[6/5/2007 3:14:15 PM] [1] Ending processing.
[6/5/2007 3:14:18 PM] [0] End of Setup
[6/5/2007 3:14:18 PM] [0] **********************************************
this I am trying on my test system please help me out in resolving the issue
thanks in advance,

Gary,
Open Registry Editor.
In Registry Editor, navigate to the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\MSExchangeIS\ParametersSystem
Create the following value (REG_SZ): Working Directory and give it a value that points to the new database folder.
Make sure you back up the registry before you do any changes on it.
Raj

5.1.4 update breaks HDV capture? Unable to Initialize Capture Device

Problem:
Final Cut Pro cannot capture standard 1080i60 HDV footage from Sony FX1 camcorder. FCP reports "Unable to Initialize Capture Device" when the log and capture window is opened. However, the footage CAN be captured in iMovie (which is interesting, and unacceptable). When HDV>DV downconvert option on camcorder is activated, footage CAN be captured as anamorphic SD, so the camcorder and FW do work.
The problem is occuring on a rock-solid FCP system that I use on a regular basis (mainly for SD editing). It has been approx 2 weeks since I last attempted a HDV capture, the system has been working great with SD footage (still does).
Factors that have changed to my knowledge since HDV capture was last functioning properly:
*Added a new external FW drive into regular usage (a different brand than normally used, no issues with it so far).
*Updated FCP to 5.1.3, and then 5.1.4 when that fix came out. All SD captures and work have been fine so far.
Here's what's interesting...I had a copy of the FCP v5.0.4 .app that I had saved an archive of prior to the crossgrade update. Guess what? I can load it up, and it captures HDV without any problems! With that in mind, this looks like an FCP 5.1.4 issue. But I am at a loss on how to proceed further in troubleshooting. Many thanks in advance for any assistance.
Matt Jeppsen
FresHDV.com
---NOTES---
What I have tried:
*Attempted capture with a different Sony FX1 camcorder.
*Swapped firewire cables and system firewire ports.
*Attempted capture with camera FW chained to an external HDD.
*Unplugged all other external firewire devices from the system.
*Trashed FCP prefs using FCP Rescue 5, created new project using Easy Setup (for HDV).
*Tried different variations of FCP A/V settings, tried all the HDV FW device control presets and the HDV AIC capture preset.
*Per instructions at http://docs.info.apple.com/article.html?artnum=301852 I removed the numbered Quicktime pckg Receipts and re-installed the latest version (7.13). Post-install/reboot, I repaired Disk Prefs and Verified the disk using Disk Util.
*Have also attempted installing QT 7.13 2 and 3 times in a row, also trying disk prefs repair BEFORE the post-install reboot.
Final Cut Pro Audio/Video Settings:
Sequence Preset: HDV-1080i60
Capture Preset: HDV
Device Control Preset: Sony HDV Firewire
Sony HDR-FX1 IN/OUT REC settings:
*VCR HDV/DV: HDV
*COMPONENT: 1080i/480i
*i.LINK CONV: OFF
*TV TYPE: 16:9
*A/V->DV OUT: OFF
System/Software Facts:
*Final Cut Pro 5.1.4
*Quicktime 7.13
*PPC Mac G5 2.7 Dual (2.5GB RAM)
*35GB free on System, 45GB free on internal FCP Scratch disk
Final Cut Pro 5.1.4, G5 DP 2.7 (PPC) Mac OS X (10.4.8)

I think I figured out this vexing problem. I too was having the same issue. Check to see that your Quicktime is newer than 7.1.2. If it isn't you'll have to upgrade it. I only upgraded to 7.1.6 here because I was afraid of going to a really new version. http://www.apple.com/support/downloads/quicktime716formac.html. After I upgraded my quicktime, I ran software update and the Final Cut Pro 5.1.4 update appeared. I hoipe this helps.

Unable to initialize capture device and device control in HDV

I shot with a Sony HVR-Z1U/Z1N and am using a Sony HDV 1080i tape deck to digitize.
I recently purchased a MacBook Pro and installed FCP Pro 5 on it. After getting over some time code issues we were chugging along, when on the 4th tape the image on the log and capture screen suddenly dissapeared (I could get audio and could see the image on the tape deck). Well after taking the tape out, checking and rechecking it I popped it back in and ever since then, I have been getting this error mssg "Unable to initialize capture device and device control."
I have tried deleting the preferences and starting from scratch. If I do that, and choose the easy setup with HDV- 1080i60, it gives me this error "Unable to locate the following external devices- HDV (1440 X 1080) 30fps.
I upgraded to FCP 5.1.2 this morning and upgraded the OS to 10.4.7 and QT to 7.1.3 and still no change.
Im at my wits end, Ive been working on this for a whole week now.
Thank you,
Bugs

It has been reported to take more than one attempt to correct the installation but, if properly executed on a machine without other system problems, the QT reinstall process does work. The key element here is you must reinstall QT after you trash the receipts. The process is listed below.
x
To do a full quicktime reinstall.
Go to /library/receipts and delete any files that say Quicktime followed by a number e.g. Quicktime703.pkg
Go to the Apple quicktime site and download the appropriate version of Quicktime to your hard drive.
Run the Quicktime installer.
Repair Disk Permissions for your System Disk (Disk Utility > Select the system disk > Repair Disk Permissions)
Reboot
If this doesn't work, then the problem lies elsewhere:
1. your system - user preferences, firewire ports or other system elements.
2. your equipment - camera/deck/firewire cables.
3. your process - not setting up the software properly or using the software erroneously.
Listed below is a troubleshooting process. Not all steps are appropriate but the general process of isolating the problem is useful.
Troubleshooting Steps for OS X
by Jan Johannsen (Collected from: Apple>User Tips Library>User Tips Contributions forum)
FIRST AID
01 Completely shutdown, wait a 5 minutes, restart
02 Make sure you're not running out of free space on the System volume
03 Check/fix the filesystem using Disk Utility &/or Diskwarrior
04 Repair permissions using Disk Utility
05 Create a new user account, and see if the problem persists there
06 Clear system & user caches
07 Run FCP Rescue
08 Unplug all USB, Firewire devices except Apple mouse
09 Startup in SafeBoot mode, and see if the problem persists there
10 Reset system firmware
MORE SERIOUS TROUBLESHOOTING
11 Reapply the latest combo updater
12 Run the Apple hardware diagnostic CD
13 Check the hard drive for bad blocks
14 Take out 3rd party RAM
15 Unplug 3rd Party PCI cards
16 Reset PMU
17 Archive and reinstall the OS
18 Reinstall the system from scratch
19 Send the machine back to Apple

Unable to initialize video deck, (can not capture from camera)

Hello All,
I am using a quad core G5 and am trying to capture some footage into Final Cut Pro version 5.0. I have two Panasonic DVX 100B mini DV cameras. I normally capture with a JVC BR-DV3000 mini DV deck but it is currently not working. So I'm trying to capture using my camera.
I hooked my camera up to my computer via firewire and started final cut, When I click File > Log and capture a little window pops up that reads:
" Unable to initialize video deck. You may still log offline clips or use Capture Now"
I'm not sure why this box is appearing. When I click the capture now button, the Capture window pops up and then I press play on the video camera and the footage plays on the camera but the capture window remains black or empty. I have tried both cameras and two different firewire cables with the same results. I have also tried to restart the computer.
Can anyone shine some light on this situation?
Thank you so much for your help.
Mike Wardynski

Are there any other firewire devices connected to your Mac?
Did you go into your easy setup and reselect the DV setting for the standard you are using?
Also sometimes, shutting down and restarting your Mac, after making these changes some times allows the new device to be recognized.
One other thing, the DV camera may have a menu setting that needs to be set for communication via firewire possibly?

Unable to initialize the server: Server failed to bind to the requested por

I am facing the error while starting the server. I see the following error.
<Sep 26, 2007 11:49:54 PM EDT> <Emergency> <WebLogicServer> <BEA-000350> <Unable to create a server socket on Channel Default for: 162.86.20.87, port: 8101. java.net.BindException: Address already in use Perhaps the address 162.86.20.87 is incorrect or another process is using port 8101.>
<Sep 26, 2007 11:49:54 PM EDT> <Emergency> <Security> <BEA-090085> <Server failed to bind to the configured port. The port may already be used by another process.>
<Sep 26, 2007 11:49:54 PM EDT> <Emergency> <WebLogicServer> <BEA-000342> <Unable to initialize the server: Server failed to bind to the requested port. See preceeding log message for details.>
The WebLogic Server did not start up properly.
Exception raised: 'weblogic.server.ServerLifecycleException: Server failed to bind to the requested port. See preceeding log message for details.'
Reason: Server failed to bind to the requested port. See preceeding log message for details.
If the port is already in use how to find which server is running on that port, how to find the process and kill it. I am using weblogic 8.1 sp4 in Solaris 8.

Bruce:
It sounds like (as you already note) failed to shutdown WLS, that is why the
.loc file was held and why the port is in use, WLS process was still
running. To see why it failed to shut down, I would examine the
weblogic.log, aslo the servers std out and err. Additionally taking a
thread dump (if possible) on the "it wont shut down" wls java process should
show (maybe unless the VM is hosed), where/what is hanging on/around. Do
you happen to have native code running with wls, say a type 2 JDBC driver?
Otherwise it sounds like a VM bug. But more data is needed to be sure.
Cheers
mbg
"Bruce Bryan" <[email protected]> wrote in message
news:3ef08499$[email protected]..
I was shutting down the WLS server using the console shutdown and itfailed to shutdown completely. I then attempted to use the kill command on
the process which usually works. This time I was unable to kill the process
without using the kill -9 command. When I attempted to bring the server
back up I got a failure to get a lock on the embedded ldap. I removed the
.loc file and came further up but was unable to get further than the
listener ports which were still locked to the old process. Do you know of
anything I can do the get the WLS server back up without rebooting my
Solaris server????
netstat -an shows the port is in use but the only process that is alloweduse that port is WLS.

Unable to initialize the Microsoft Exchange Information Store service. - Error 0x96f.

PLease help, I've rstored from backup three times with no success I'm getting the following error
"Unable to initialize the Microsoft Exchange Information Store service. - Error 0x96f. "
It's LDap related but i have no idea why :-(
Best Regards Bernhard

IPv6 had been disabled for months on my SBS 2008 Server running Exchange 2007 SP1. I ran 40 or so Windows Updates; subsequently, the next morning Exchange was no longer running; topology issues, event ID 2604, 2114 and 2601 were all over my Application
Log. After 12 hours of research I found this post; figured it was worth a shot and instantly all my services for Exchange fired up. Thanks for the tip; I have no idea which update changed what in regards to needing IPv6 enabled, but that silly
little check mark fixed it.
Thank you for sharing your solution!
Dan

Unable to Initialize Capture Device - Works fine in iMovie

Am using a Sony HDV HDR HC1E Pal Handycam
Final Cut Pro 5.1
QT Pro 7.1.3
Works fine with cassettes in HDV - imports into FCP fine
Am trying to import a cassette recorded on that camera in DV LP
Works fine in iMovie
Have deleted the QT packages and reinstalled QT
Still am getting the 'Unable to Initialize Capture Device' message when using log and capture.
Settings on camera
VCR Auto (have also tried HDV or DV)
iLink conversion off (i.e.don't convert hdv-dv)
TV type 16:9 (have also tried 4:3)
Component 1080i/576i also tried 576i
Annoying thing is that works fine in iMovie but not FCP?!!
Any help GREATLY appreciated!
Thanks!
Hannah
iMac 20 Flat Screen G5 1.8Ghz 1.5GB SDRAM Mac OS X (10.4.8) 200 GB and 120GB External Hard drives

I would like to add the following in hopes that someone will come up with a solution. The problem lies somewhere in Quicktime and the FireWire capture. I have the exact same camera and problem, and can assure you it has nothing to do with cam settings or DV LP. Once your system is stuck in this HDV mode, it would seem that regular DV can not be used again. I also have 2 other DV cams that are not HD. One is PAL, one is NTSC. I would further add that my external FireWire iSight no longer works in any application. I do not receive error messages, I simply get the spinning beach-ball of death.
I have a Dual G5 2.7 with 4 gigs RAM running FCP 5.0.4 on OS 10.4.8
I have run Cocktail, rebuilt permissions and re-installed Quicktime 7.1.3 four times as per Apples tech article 301852
I have used FCP Rescue 5 to clear preferences
I have captured footage from both regular DV cams to iMovie and then added the footage to FCP. The footage plays on the screen of both DV cams flawlessly via FCP. (I can also capture HDV in iMovie as well)
I have tried logging footage directly through the QuickTime application with both DV cams and my iSight and get the same beach-ball of death as FCP.
Why can iMovie work with these devices flawlessly yet QuickTime can not.
Why does it seem like the system is stuck in some kind of HD mode.
Just to point out the obvious:
I have no other FireWire devices other than the cameras and I only connect one at a time.
I have shut down, disconnected and re-connected before attempting to use the devices.
I have booted my G5 from a second system disk and everything (HDV cam PAL DV cam NTSC cam and iSight) function flawlessly on all the FireWire ports of my machine.
I have worked with FCP for about 6 years and Macs for 20. I understand the easy set ups etc.
Spent way too much time customizing my system to think about the clean install route, so I hope someone can shed some light on this.
Thanks
Lorne
PowerMac Dual 2.7 GHz PowerPC G5 4 GB DDR SDRAM 400 GB and 250 GB Internal Drives Mac OS X (10.4.8)

Messaging 3.x fails to start with "Unable to initialize" error

Messaging Server fails to start from the Admin Server or by using the "start" command.

# /etc/NscpMail start
Startup Problem:
Unable to initialize the environment from (/etc/netscape.mail.conf)
Netscape Messaging Server Exiting!

The Messaging Server log file will not show any entries.

The problem is most likely due to a missing dbswtich.conf
file or a zero byte file.

The default dbswitch.conf
file contains a single line:

directory default ldapdb:///usr/netscape/suitespot/userdb/ldap/config/lcache.conf/

Restore this file from a backup if possible.

Unlike Admin Server, Messaging Server will require the correct file to be
restored because it immediately looks for its postmaster entries in the LDAP
directory. If you cannot restore the file:
<OL>
<LI>Place a temporary entry into the
file.
<LI>Start the admin server.
<LI>Enter the correct values into Global Settings,
Configure Directory Service.
<LI>Attempt to start the Messaging Server again.
</OL>

Tracing utilities (e.g. truss in Solaris) can
help analyze problems where servers fail to start and return little or no
useful errors.

truss -f -o <trussfile> /etc/NscpMail start

grep dbswitch.conf <trussfile>.

This would usually show admin returning a ENOENT error or reading zero bytes of
data.

I assume when you say "mentioned solutions", those include:
- Generating xorg.conf with aticonfig --initial
- Blacklisting the radeon module
- Generating the fresh fglrx modules with catalyst_build_module all
Also, how've you set it up? AUR, graysky's repository or directly from AMD's website?
Last edited by clfarron4 (2014-09-15 12:16:09)

Has anyone solved the "Unable to initialize API" e...

I have an E61 that I'm trying to Sync to Lotus Notes 7 on my Windows XP sp2 Thinkpad. However, I keep getting the following error "Unable to initialize API" I can see that other people have been getting the error too. Nokia's web Site states that PC Sync works with Lotus Notes so I hope that there is a simple fix to this.
Thank You Penn Jennings

Hi Synch,
I checked the computer for notes.ini. There is only one file of this name. Its located in C:\Program Files\lotus\notes
I installed the latest version of the Nokia Suite 7.0.7.0
Here is the export of the registry key you requested"
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Components
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Components\LotusScriptExtensions
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Components\LotusScriptExtensions\2.0
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Value 0
Name:
Type: REG_SZ
Data:
Value 1
Name: Notes
Type: REG_SZ
Data: C:\Program Files\lotus\notes\nlsxbe.dll
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Components\TeamMail
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Value 0
Name: Description
Type: REG_SZ
Data: TeamMail Mail Enabling dll
Value 1
Name: KeyPath
Type: REG_SZ
Data: Software\Lotus\Notes
Value 2
Name: Application
Type: REG_SZ
Data: Notes
Value 3
Name: Version
Type: REG_SZ
Data: 1.0
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Notes
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Value 0
Name: DataPath
Type: REG_SZ
Data: C:\ntsdata\
Value 1
Name: Path
Type: REG_SZ
Data: C:\Program Files\lotus\notes\
Value 2
Name: Name
Type: REG_SZ
Data: Notes.exe
Value 3
Name: Description
Type: REG_SZ
Data: Lotus Notes
Value 4
Name: MultiUser
Type: REG_DWORD
Data: 0x0
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Notes\7.0
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Value 0
Name: DataPath
Type: REG_SZ
Data: C:\ntsdata
Value 1
Name: Description
Type: REG_SZ
Data: Lotus Notes
Value 2
Name: Name
Type: REG_SZ
Data: Notes.exe
Value 3
Name: Path
Type: REG_SZ
Data: C:\Program Files\lotus\notes
Value 4
Name: MultiUser
Type: REG_DWORD
Data: 0x0
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Sametime Client
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Sametime Client\StConnAgent
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Lotus\Sametime Client\StConnAgent\IBMLotusNotes65
Class Name:
Last Write Time: 28/02/2008 - 1:25 PM
Value 0
Name:
Type: REG_SZ
Data: C:\Program Files\lotus\notes\stconnagent30.exe
I tried this on another laptop we have, a Dell D505. Notes is setup in what looks to be exactly the same way. Using the same ID file in the same location.
The Nokia Suite works perfectly with the this setup.
I compared the two registry entries for HKEY_LOCAL_MACHINE\SOFTWARE\Lotus. Besides differences in dates, both keys are exactly the same. So we have two computers where the connection works perfectly, it picks up the server and then you can log into it with a password. The other system won't connect to the Notes server and you can't get anywhere.
Any help appreciated.

Unable to initialize new provider instance

Hi all,
This problem has now been posted a few times since May 27 but remains unresolved. It presents itself after the final step while following the procedure for "registering the provider" as described in "installing.jpdk.html".
The error message reported to the browser is as follows:
Error: An error occurred when attempting to call the providers register function. (WWC-43134)
The following error occurred during the call to Web provider: Unable to initialize new provider instance: java.lang.NumberFormatException: (WWC-43147)
There are log files excerpts pertaining to this event in the Cheung thread.
Can anyone shed any light on this?
Regards,
Jim
null

Hi Sue,
Thank you for your help!
What PDK release are you using PDK-May or PDK-June?Ahah! I think you may have hit the nail on the head straight away.. While checking my reply I found that I used a file called "pdk.zip" which was downloaded from http://otn.oracle.com/sample_code/products/iportal/sample_code_index.htm. This archive contains the file that I installed, which is called jpdk14.zip and is dated 4/23/2001 (this itself contains files with latest last modified date of 3/26/2001).
Presumably this file is obsolete?
Can you get the test page to display? Yes.
You used the exact same URL from the test page for registration?Yes - cut, pasted and verified!
Did you make any other changes in the provider.xml other than what appears at the top?No.
I guess these answers are largely academic, how about if I try again using the latest file from http://portalstudio.oracle.com/pls/ops/docs/FOLDER/COMMUNITY/PDK/INDEX.HTML and let you know the result?
Best Regards,
Jim

Unable to initialize logging infrastructure for localization

Similar Messages

Maybe you are looking for