USB Output Buffers - int to Hexed Chars

Hi all
With regards sending data to a USB device I set up a char like so:
size_t bufferSize = 8;
char *buffer = malloc(bufferSize);
I can then populate my bytes in hex (which seems to be the normal way of doing it).
    buffer[0] = 0xFF;
    buffer[1] = 0xEA;
The two fold question is will I have any issues if i populate the char buffers with integers?
    int value = 256;
    buffer[0] = value;
or does it have to be in hex?
If it requires hex (or even if not cos it would be good to know). What the best way to convert and integer to a hexed char?
Cheers
Steve

It doesn't matter if you specify the value in hexadecimal, decimal, octal or binary (or any other numbering system for that matter).
A number has the same value no matter what base you use.

Similar Messages

Output of int value to char

hi,
I have written the following code
class LiteralTest
     public static void main(String[] args)
          System.out.println("Hello World!");
          int true1=100;
          float flt = 17.2345678f;
          short sh = (int)500;
          char a=0x892;
          char b=982;
          char c=(char)70000;
          char d=(char)-98;
          System.out.println(a + " -- "+b+ " -- "+c+ " -- "+d);
the output is
Hello World!
Please explain why the values are '?' and not the actual values?
Deepali

And why are you specifying a character with a
negative number?Casting a negative number to a (unicode) char is valid. For example
            int c = -1279;
            System.out.println(c);
            char ch = (char)c;
            System.out.println(ch);prints the 'ﬁ' character which has unicode value 0xfb01.

Audio No Longer Working on USB Output

Hi,
I've been using Audirvana, Bit Perfect, and other music software applications with iTunes.
Last night I unhooked the power cord and the music stopped playing. I've tried everything and anything to fix this but I am no longer getting audio out from my USB port (I've tried both ports).
When I go into Audo MIDI Setup I see my bridge (Musical Fidelity USB -> SPDIF Converter) as always. However, when I select it and "Use This Device for Sound Output" nothing happens and it doesn't change (it stays on either Airplay or Built-in Output).
In addition, I am unable to change anything on the USB Output (Master Volume, Analog 1, Analog 2...the only thing I an do is 'mute' which I don't want to do).
When I look at my Musical Fidelity Bridge and DAC it *appears* that they are getting signals - they both say 'Locked' when a signal is present.
I wonder if it's because the volume on my USB output is so low and I can't change it? See picture.
Please help! The only reason I have this MacBook Pro is to play music through my system.

Open the Speech pane of System Preferences and check whether either the listening key or the speech key has become set to that keystroke; if so, change the setting.
(60747)

Outputting an int variable in an applet?

Hey all i will keep this short, i am modifying an applet for a university project and am trying to output an integer variable to screen, i tried using g.drawString but i apparently can only use it to output "text in the double quotes" and if i try putting the variable in without the double quotes it throws an error, i was just wondering how would you output a int variable to screen in an applet, thanks

To convert an int to a String, use:
String.valueOf(int)

Int to Hex Progam

Could someone help resolve this problem : I have created a program to change int to hex but it does not seem to woek ? What could be wrong ?
import java.lang.String;
import javax.swing.JOptionPane; // import class JOptionPane
public class KcHexConverter {
public static void main( String args[] )
     String value, s;// first string entered by user
     int ni=0;
          // read in first number from user as a string
          value = JOptionPane.showInputDialog( "Enter integer" );
// convert numbers from type String to type Hex
          ni = Integer.parseInt(value, 16);
          s = Integer.toHexString(ni);
// display the results
JOptionPane.showMessageDialog(null, "The equvalent in Hexadecimal is: " +s, "Results", JOptionPane.PLAIN_MESSAGE );
System.exit( 0 ); // terminate the program
}

Hi
you need to change:
ni = Integer.parseInt(value);//no need for a radix it is base 10
and you should catch a possible NumberFormatException (sb enters a letter).

The display speakers, the camera display, and all three USB outputs in the back are not working?

The speakers, the camera display, and all the USB outputs in the back are not working.
I was typing a paper last night when the electricity went off, and 5min later went back on, and all the display speakers, the camera display, and all the USB outputs in the back are not working.
FYI, it's LED Cinema display.
Solutions? Suggestions?

Hi,
Actually BACK is standard user command so it is not stopping and going to selection screen.
Give some other use command like 'BCK' and try....

Hex chars in strings

Hi
Is it possible to insert hex chars inside a string, like unicode chars \u, but for hex, like \0xFF....
I have \x in my java book but that doesnt work.

Hi,
Just use it without '\'
System.out.println("Character with value hex value 41: " + (char)0x41 + " Can you see it?");Prints:
Character with value hex value 41: A Can you see it?
/Kaj

USB output devices and GarageBand 08

I have seen several posts discussing that Garage Band 08 does not use the USB Companion 5 speakers as an output. Does anyone know if there is a way to get Garage Band to use USB as an output? Additionally does anyone know if Apple has any plans to support USB output? I have some expensive speakers going to waste with Garage Band.

Not from what I have seen in the threads and throught my own personal experience. My Itunes plays great through the Bose Speakers. In Garage Band if I choose Built in as the Audio Output Channel...no probs...if I change it to USB Bose or Match Systems settings which are also USB....Garage band hangs and I get the rainbow wheel of death when I do anything.
http://discussions.apple.com/thread.jspa?messageID=6118937
http://discussions.apple.com/thread.jspa?messageID=6315926&#6315926

Thunderbolt display speaker USB output not selectable

Hi There,
My thunderbolt display was working perfect before I upgraded to Mountain Lion.
Now I found it doesn't let me select ThunderBolt display speaker USB output.
it will jump to internal speaker right away once I select USB output.
I had ensured no any other USB connected to my MacBook Pro.
I am very sorry that the Chinese Snapshot attachment, but you can easily guess what the item is.
My Macbook pro is 2011 made, with 2 GHz Core i7, 16GB 1333 DDR3, now OS is 10.8.4,

Don't feel bad. You are certainly not the first person to make that mistake and it is equally certain you will not be the last.

I have a turntable with USB output and SoundStudio3 software; can't get any input. Can you help??

I have a turntable with a USB output and SOUNDSTUDIO3 software. I cannot"find" any audio to record. Can someone help "Denny-Dumb-Butt" see what he is doing wrong?? THANKS!!!

Did you also check if your USB device shows up in System Preferences > Sound?
I have an iMic USB "dongle" and need to select it if I want to record from an external source into Sound Studio 3. You need to check both the Input and Output.

Pulsing static sound is audible thru speakers or earphones, but not USB output.

Compaq Presario CQ532oF Windows 7 64 bit
Pulsing static sound is audible thru speakers or earphones, but not USB output. Makes listening to talk or music unbearable. This just started a few days ago. Volume control affects the volume. Does not matter if audio program is playing or not playing. Pulses are about 2 seconds duration - sounds like a phonograph record at the end of play where the tone arm didn't pick up.
Is this likely an amplifier problem? Is the amp on the sound card?

Hi vc329,
Doesn't sound like encouraging news, though it is odd that the sound came back for a short while at least. If you still haven't rebooted the PC since putting it to sleep and loosing the sound, then I would suggested going ahead and rebooting or even doing a full hard reset (power down, remove the AC adapter, remove the battery, hold down the power button for 20 seconds or so, then reconnect the AC power and Battery and boot up) to see if the sound can be recovered again.
If the sound still doesn't work, Check Device Manager to see if the sound driver still looks OK, make sure you are using the latest driver again (it looks like the latest driver is 6.10.6381.0), another option might also be to try the older driver that is still available from the site, or try recovering the original driver shipped on the PC. The steps to do these things are covered in the document listed below, in Step 6 (Restoring the Audio Driver), Step 7 (Updating the Audio Driver), and Step 8 (Checking Device Manager):
No Sound from the Speakers (Windows 7)
If none of that seems to help, I'd recommend testing the hardware using Step 9 in that document.
If the online warranty check sees you as out of warranty, you may still be OK if you have the original proof of purchase (receipt) from wherever you purchased the PC, but you may have to provide it when calling HP for service if the sound can't be fixed. If you are close to the end of warranty I'd recommend calling customer care for your area (I assume you are still in Asia) and validating the warranty with them as soon as possible just to make sure.
Although I am an HP Employee, I am speaking for myself and not for HP.

USB output with headset failure!

Hello,
I have a strange problem. The USB port works on both sides
with every other peripheral. Only when I use the headset which
also works (tested on another computer) does the USB output
not work at all. The audio mini jack port works too!
The preferences audio DO recognize the USB headset! The
input registers a voice too! Tried Audio Midi too! Please help!!!
OS 10.4.10 Powebook G4 17"
laminaksi

Welcome to the Apple discussions.
Sometimes USB issues can be fixed by resetting the Power Management Unit (PMU). See this Apple article: http://docs.info.apple.com/article.html?artnum=14449

Internet Audio will no longer Play Through USB Output to hi-fi Amplifier & Speakers

My audio output jack on my Mac G4 is broken. I have been taking audio out of the computer by USB into a device that converts the audio so it can be used with a traditional amplifier and speakers. This presently, still works fine for audio or audio/video sources that are stored on my hard drive. Yesterday, I was looking at a youtube video embedded on a non-youtube site. Both audio and video were working fine.Then the audio stopped working. I went to the youtube site and no audio worked there either. I have tried myspace and other sources with audio/video, but no longer will audio from the internet, play on the USB system. Any player on the hard drive will produce audio through the USB port to the amplifier system. If I switch the Mac OS X.4.11 system preferences to select the internal speakers for the output destination, I can get audio from the internet again. Then everything from the internet or the computer plays through the internal speakers. I have Safari and Firefox Browsers. I need to be able to play music from the internet through the USB port to my amplifier and speakers. One suggestion I researched was to trash the Macromedia preferences and then restart the browser. I tried that to no avail. Hopefully, somebody out there knows what happened and can tell me how to fix it.

Hi BD,
Thanks for saving me. And thanks for responding so quickly. Your answer was there when I got up. For me 48 hours was a long time to go without that function.
I had seen one reference to the audio midi setup app and had looked at it but somehow only saw the midi devices dialog box which I had dealt with in the past. After your post I went back to it and I immediately discovered that there is also an audio devices dialog box.
From the drop-down menu I selected 44100.0 hz int the format field on the output (right) side of the dialog box.
Also the Default Ouput and the System Output fields had built-in audio selected instead of iMic USB audio system. I used the drop-down menus to switch them back.
So watching the youtube video imbedded on a non-youtube site must have changed those settings.
Any idea why that would have happened?
Now, I'm wondering if the little iMic USB audio system which converts the digital signal to analog line level out is actually a little midi device? Well, maybe not since there is no midi plug involved. I have seen that setting (44.0 Khz) relating to CDs I think. I'm guessing that 44.0 Khz and 44100.0 hz are very close to being exactly the same thing.
So does 44.0 Khz = line level (analog audio)?
Anyway, BD, Thanks again for solving my problem and doing it so quickly. What a relief!
Have a great 4th of July holiday weekend,
Skip

RDF Report Output Got Displayed in Special Chars

Team,
RDF report output is getting displayed in special chars.
when i query the data from SQL Developer, the data is displayed fine.
But when the data is displayed in the report the characters(single quotes, double quotes) are not displayed properly, they are displayed in a special char.
why it is happening so . Is it related any font missing ? Plz do let me know.
thanks
sridhar

(single quotes, double quotes) These are probably not really single and double quotes. Check the ASCII value.
drop table ttest;
create table ttest (col1 varchar2(10));
insert into ttest values ('''Quote''');
insert into ttest values ('"Quote"');
select * from ttest;
select dump(col1) from ttest;
Table dropped.
Table created.
1 row created.
1 row created.
COL1
'Quote'
"Quote"
2 rows selected.
DUMP(COL1)
Typ=1 Len=7: 39,81,117,111,116,101,39
Typ=1 Len=7: 34,81,117,111,116,101,34
2 rows selected.

Int to hex?

Is there a predefined way to change an integer to hexidecimal?
For Instance:
int ip1 = 166;
ip1 to hex = 0xA6
I had thought I read about this in the docs, but can't find it.
Thanks

I appreciate the response. To explain my reasoning: I am building a byte array and I need to put each of the four number segments of an ip address into the array.
Would this work? Forgive the fast-coding.
String SrvrIP = srvrIpAddr.getHostAddress(); // i.e 166.10.10.0
StringTokenizer ip = new StringTokenizer( SrvrIP, "." );
int ip1 = Integer.parseInt(ip.nextToken());
int ip2 = Integer.parseInt(ip.nextToken());
int ip3 = Integer.parseInt(ip.nextToken());
int ip4 = Integer.parseInt(ip.nextToken());
byte[] buf = new byte[512];                // Does it give me this??
buf[0] = Integer.toHexString(ip1);              // buf[0] = 0xA6
buf[1] = Integer.toHexString(ip1);              // buf[1] = 0x0A
buf[2] = Integer.toHexString(ip1);              // buf[2] = 0x0A
buf[3] = Integer.toHexString(ip1);              // buf[3] = 0x00Thanks

USB Output Buffers - int to Hexed Chars

Similar Messages

Maybe you are looking for