Virtualbox network

I would like to configure "network host interface" on virtualbox. I already configure everything like it's explained on the wiki "Using host interface networking (the Arch way)" but it's not working.
My host is archlinux and my guest is archlinux.
On virtualbox - setting - network
Attached to: Host interface
Interface Name: vbox0
This is my /etc/conf.d/bridges
# Settings for layer-2 bridges
# For each bridge interface declared in INTERFACES (in rc.conf), declare
# a bridge_${IF} variable that contains the real ethernet interfaces that
# should be bridged togeether.
# Then list the bridge interface name in the BRIDGE_INTERFACES array.
# example:
# in /etc/rc.conf:
# eth0="eth0 up"
# eth1="eth1 up"
# br0="br0 192.168.0.2 netmask 255.255.255.0 up"
# INTERFACES=(lo eth0 eth1 br0)
# in /etc/conf.d/bridges
# bridge_br0="eth0 eth1"
# BRIDGE_INTERFACES=(br0)
bridge_br0="eth0"
BRIDGE_INTERFACES=(br0)
This is my /etc/rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="pt_PT@euro"
HARDWARECLOCK="localtime"
USEDIRECTISA="no"
TIMEZONE="Europe/Lisbon"
KEYMAP="pt-latin1"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(e100 eepro100 mii r8169 slhc ac97_bus snd-mixer-oss snd-pcm-oss snd-page-alloc vboxdrv snd-pcm snd-timer snd snd-ac97-codec snd-intel8x0 soundcore bridge tun)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="arch2"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
lo="lo 127.0.0.1"
eth0="eth0 up"
br0="dhcp"
eth1="eth1 192.168.3.25 netmask 255.255.255.0 broadcast 192.168.3.255"
INTERFACES=(lo eth0 eth1 br0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.3.2"
ROUTES=(gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network portmap nfslock netfs hal fam @vboxnet @crond @alsa)
Adn this is my /etc/vbox/interfaces
# This file is for registering VirtualBox permanent host networking interfaces
# and optionally adding them to network bridges on the host.
# Each line should be of the format <interface name> <user name> [<bridge>].
vbox0 amadlopes br0
When i do ifconfig -a on the host
bash-3.2# ifconfig -a
br0 Link encap:Ethernet HWaddr 00:11:2F:44:E0:55
inet addr:192.168.2.102 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::211:2fff:fe44:e055/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:39944 errors:0 dropped:0 overruns:0 frame:0
TX packets:21864 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:17009365 (16.2 Mb) TX bytes:9119425 (8.6 Mb)
eth0 Link encap:Ethernet HWaddr 00:11:2F:44:E0:55
inet6 addr: fe80::211:2fff:fe44:e055/64 Scope:Link
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:39946 errors:0 dropped:0 overruns:0 frame:0
TX packets:21865 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:17579627 (16.7 Mb) TX bytes:9118183 (8.6 Mb)
eth1 Link encap:Ethernet HWaddr 00:06:4F:56:68:D1
inet addr:192.168.3.25 Bcast:192.168.3.255 Mask:255.255.255.0
inet6 addr: fe80::206:4fff:fe56:68d1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:911494 errors:0 dropped:0 overruns:0 frame:0
TX packets:613554 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1208478584 (1152.4 Mb) TX bytes:273773449 (261.0 Mb)
Interrupt:17 Base address:0x8c00
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:92 errors:0 dropped:0 overruns:0 frame:0
TX packets:92 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5992 (5.8 Kb) TX bytes:5992 (5.8 Kb)
tap0 Link encap:Ethernet HWaddr 00:FF:6D:2B:CB:E0
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
vbox0 Link encap:Ethernet HWaddr 00:FF:51:05:49:78
inet6 addr: fe80::2ff:51ff:fe05:4978/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1644 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:6 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:393640 (384.4 Kb) TX bytes:0 (0.0 b)
When i boot the vm (archlinux):
err, eth0: timed out
warn, eth0: using IPV4LL address 169.254.237.41
I alreaddy read the user manual of virtualbox and i tryed them way of doing it but it didn't work too.
I already google but i really confused...
Thank you for your help
Last edited by amadlopes (2008-10-13 17:49:03)

after exiting, IExplore.exe and wineserver and explorer.exe gets stuck and eats one full cpu core. it's time to create an exit bash script

Similar Messages

  • [SOLVED] No luck with VirtualBox network.

    EDIT**********
    I have a working Arch Linux VM made with VirtualBox. The network works out of the box but once you reboot and remove live media and load into Arch Linux I cannot get a ping.
    I have looked through the Arch Linux VirtualBox wiki and I am either confused or feel I have tried what it asked.
    Here is what I did.
    For the purpose of this post, I made a new VM and successfully followed the beginner guide again and installed Arch Linux and it starts up no problem without the live iso.
    first thing I did was
    ping -c 3 www.google.com
    unknown host...
    so i did
    ddhcpcd
    and this resulted...
    dhcpcd[196]: version 6.7.1 starting
    dhcpcd[196]: enp0s3: adding address fe80::ced8:2d68:7409:4427
    dhcpcd[196]: no interfaces have a carrier
    dhcpcd[196]: forked to background, child pid 208
    https://wiki.archlinux.org/index.php/Vi … VirtualBox
    I have no idea where to learn about this in the exhaustive guide that mostly has nothing to do with what I am using VirtualBox for.
    [SOLVED] Josh Braun’s Blog // A Guide to Installing Arch in VirtualBox
    http://wideaperture.net/blog/?p=3851
    Solved using this code. I did not see anything about this in the Wiki.. so check out Josh Brauns Blog.
    # systemctl enable [email protected]
    Old Horrible Question... DO NOT READ
    I can dual boot Arch from my bios and get wifi access easily.
    When I use VirtualBox, it has no problem until I actually log on to Arch Linux without the live iso.
    I have did searches and i am just LOST on the VirtualBox Arch wiki.
    Edit: I have tried dhcpcd and it was not successful. I will post the exact output later.
    I am hoping someone can direct me to get this working.
    I have a windows 7 Dell laptop and VirtualBox loads into Arch Linux without the iso as a drive. Just looking for guidance and search terms. Thank you./
    Last edited by AcousticBruce (2015-03-12 00:20:43)

    That's understandable, I know well myself how intimidating it can be at the very beginning.
    I will explain a bit. Those guides are just asking for trouble for two reasons: (1) they are outdated and Arch moves quick. And (2) it will prevent you from learning how to administer your system. You copied and pasted that command but did you know what you were doing? Probably not. I guarantee you will run into that same problem again if you don't know how systemd and services, etc. work in general. The first link to dhcpcd was the section about running the service. Notice it links to the systemd page that explains in general how to start, stop, enable, and disable services. This is the kind of research you will need to do on your own if you hope to get to the point where you don't have to ask questions about every single step. It's okay to ask questions, but when it comes to something as straightforward as enabling a service, people will usually just point you to the links.
    If you're only a week into Linux in general and you've successfully installed Arch in a VM, then that's a good sign. The lingo will come in time but you definitely need to do a bit of studying. You should read through the wiki in depth. That is, the beginner's guide isn't just for installing Arch for the first time. It includes tons of links to all the moving parts of your system. The general recommendations page is also a must read.
    With effort and patience you'll pick up what you now don't understand at all
    EDIT: note also that the exact step that you found on this other guide is listed in the beginner's guide: https://wiki.archlinux.org/index.php/Be … Dynamic_IP
    I suspect you got drawn into the VirtualBox wiki page without slowly and carefully going through the beginner's guide as well.
    Last edited by nullified (2015-03-12 03:00:59)

  • Virtualbox + Network issue (I need internet explorer for work)

    Hi all! I have a very strange problem. I just got a new job, and I can only add and view my worktime through internet explorer. Wine didn't help, so I installed $hitdow$ XP in a virtualbox. Even before I opened a browser or used the connection for anything, I got a virus (dl.exe in a dos cmd window), and there's no problem basically with that install disk.
    Anyway the strange issue: Internet explorer after around 2-3 minutes of work says, there's no connection. I go to run/cmd and ping, and it works. Does someone have an idea, how to make IE work in wine? (aur bin32-wine-gecko didn't work, only the virtualbox solution was working yet (for 2-3 minutes), but I would be happier with a wine-based solution)

    after exiting, IExplore.exe and wineserver and explorer.exe gets stuck and eats one full cpu core. it's time to create an exit bash script

  • [solved] problem getting vbox host only networking going on arch host

    New arch user here, been running for 2-3 weeks.  Finally came across something I can't wiki/google my way through, trying to get host only networking going.
    So....  I started by trying the graphical virtualbox manager.  File -> preferences -> network -> add, which gives:
    Failed to create the host-only network interface.
    Callee RC: NS_ERROR_ABORT (0x80004004)
    Tried the following also, with no luck:
    > VBoxManage hostonlyif create
    VBoxManage: error: Code NS_ERROR_ABORT (0x80004004) - Operation aborted (extended info not available)
    Context: "CreateHostOnlyNetworkInterface (hif.asOutParam(), progress.asOutParam())" at line 64 of file VBoxManageHostonly.cpp
    Segmentation fault
    > VBoxManage dhcpserver add --ifname hth0 --ip 10.1.1.1 --netmask 255.255.255.0 --lowerip 10.1.1.10 --upperip 10.1.1.20 --enable
    VBoxManage: error: The host network interface with the given name could not be found
    VBoxManage: error: Details: code NS_ERROR_INVALID_ARG (0x80070057), component Host, interface IHost, callee nsISupports
    Context: "FindHostNetworkInterfaceByName(Bstr(pIfName).mutableRaw(), hif.asOutParam())" at line 225 of file VBoxManageDHCPServer.cpp
    VBoxManage: error: Could not find interface 'hth0'
    > uname -a
    Linux bing 3.1.1-1-ARCH #1 SMP PREEMPT Fri Nov 11 22:28:29 CET 2011 x86_64 AMD E-350 Processor AuthenticAMD GNU/Linux
    > lsmod | grep vbox
    vboxnetflt 17159 0
    vboxdrv 1790690 1 vboxnetflt
    > pacman -Q virtualbox
    virtualbox 4.1.6-3
    I also have extension pack 4.1.6r74713 if that matters.
    edit: code tags
    Last edited by nht (2011-11-19 16:37:49)

    Thank you sir, that's exactly what I needed.
    Now that I look, I see mention of this in the VirtualBox Extras section of the wiki, but not the VirtualBox or Advanced VirtualBox Networking sections.  I have edited the Advanced VirtualBox Networking wiki to add mention of this.
    Last edited by nht (2011-11-19 17:18:28)

  • Can I use Oracle Developer Day.ova for learning purposes without any  license? #developerday

    Hi,
       I am a student and learning oracle database. I have found Oracle Virtual box appliance from following link Developer Day - Hands-on Database Application Development&lt;/title&gt;&lt;meta name=&quot;Title&quot; content=&quot;Dev…
       Do I need a license to use this VM?
       Please reply.
    Thanks,
    Tahir.

    Kunwar wrote:
    Hi friends,
    i have installed oracle db using Oracle Developer Day.ova for practicing on my lappie.
    I want to connect to that DB which is inside oracle vm virtual box manager using PUTTY ( which is on my desktop). I dont want to use the in-built workspace or Terminal(whatever is its name).
    Can you guys please suggest what should i do so that i can login to the DB using the PUTTY only (i love it )? i am not able to login to the host "localhost" using the putty.
    Few years back when i had installed vmware(linux installed in it and db installed on linux) i could connect through putty.
    I am using below entry in the hosts file.
    # localhost name resolution is handled within DNS itself. 
        127.0.0.1       localhost 
    #    ::1             localhost 
    'localhost' and its ip address of 127.0.0.1 are non-routeable.  Any request to send a network message to localhost will never leave the machine from which the request originates.  And for all intents and purposes, your virtual machine is a different machine.
    See my solution at
    http://edstevensdba.wordpress.com/2012/12/15/configure-the-virtualbox-network-2/

  • [SOLVED] Pacman error: failed retrieving file : No address record

    I just installed Arch on a x86 laptop using the cd as the package source. I wanted to do a net install, but when I attempted to (regardless of the mirror) I got many responses from pacman in tty7 of "No address record". This happened despite having a network connection and being able to ping any site from the cli.
    After installing, I am still having the same problem. The laptop is plugged in via ethernet, and I can ping any site I want, but a call to pacman -Syyu just returns numerous errors such as
    error: failed retrieving file 'core.db' from mirror.rit.edu : No address record
    And just as a test, I was getting replies when pinging mirror.rit.edu.
    Last edited by process91 (2011-11-18 18:21:17)

    Try the following steps:
    1 - Set the VirtualBox Networking option to NAT
    2 -  Start the arch machine in the VirtualBox
    3 -  Edit /etc/rc.conf as a dynamic IP:
    HOSTNAME="arch"
    interface=eth0
    address=
    netmask=
    broadcast=
    gateway=
    4 - Run dhcpcd
    5 -  Try to ping a couple of sites, or your router
    If you still can't ping or anything, I suggest you start a new thread specifically about your problem. Include the output from "ipconfig -a". You're not going to get much help from posting in a thread marked "[SOLVED]".
    Last edited by process91 (2012-01-18 07:21:14)

  • [SOLVED] Internet configuration: dynamic IP problems

    Hello Arch Linux community,
    After usage of Ubuntu, I decided to move to Arch Linux because of its highly-customizable and flexible operating system. To learn first the installation process, I created a virtual OS in Oracle VM VirtualBox. The installation went well till I encountered the network configuration step. It should be noted that the internet worked fine in terminal when it was not installed and it was used from a disk image. Therefore, my installation ended here and I cannot progress. Tried many ways found on Arch's wiki and googled, but still no Internet found in the Arch Linux.
    Firstly, I have a dynamic IP. Judging from ipconfig /all command in Windows cmd at least, since it says that DHCP is enabled. What is interesting is that I found that VirtualBox internet connection does not have it enabled in cmd. However, in the program it says that it is enabled. By googling I managed to turn it on and now it can be seen in cmd that it is on. But it did not fix my problem. When trying to write ping -c 3 www.google.com or ping -c 3 8.8.8.8, I get an error saying that it did not find the host, which according to Wiki means that I cannot establish an Internet connection.
    By following this wikipedia section to configure a dynamic IP address, I managed to get rid off certain errors, but the Internet is still not reachable.
    Errors
    When I write dhcpcd eth0, I get:
    dhcpcd[223]: dhcpcd already running on pid 217 (/run/dhcpcd-eth0.pid)
    When I write systemctl start dhcpcd@eth0, I do not get anything.
    When I write systemctl enable dhcpcd@eth0, I do not get anything.
    When I write ping -c 3 www.google.com, I get:
    ping: unknown host www.google.com
    When I write ping -c 3 8.8.8.8, I get:
    PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
    From 192.168.1.23 icmp_seq=1 Destination Host Unreachable
    From 192.168.1.23 icmp_seq=2 Destination Host Unreachable
    From 192.168.1.23 icmp_seq=3 Destination Host Unreachable
    --- 8.8.8.8 ping statistics ---
    3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2002ms pipe 3
    During the installation, I encountered problems with my firewall. Using Eset Smart Security, which is both an antivirus and a firewall. I had gotten a notification from my firewall that it is blocking some kind of IP. Then, I turned the firewall off and the installation went well. However, this does not work when I try to ping in the installed Arch Linux. I do not get any notifications from the firewall both when it is on and off.
    System
    Arch Linux is installed on HDD, however, I have also a SSD, but it is used by Windows 7.
    When I write uname -a, I get this:
    Linux localhost 3.6.6-1-ARCH #1 SMP PREEMPT Mon Nov 5 11:57:22 CET 2012 x86_64 GNU/Linux
    Windows information:
    Windows 7 Ultimate
    Service Pack 1
    Computer information
    Laptop Dell XPS 1640
    Inter Core 2 Duo CPU T9400 @ 2.53GHz 2.53GHz
    Memory RAM: 4.00 GB
    System type: 64-bit OS
    Crucial M4 64GB SSD
    And an old Seagate HDD 500GB on which Arch Linux is installed.
    Last edited by decas (2012-12-16 09:32:09)

    p0x8 wrote:- type of network adapter you configured in the virtual machine (bridged, NAT, host-only)
    NAT (default)
    p0x8 wrote:- output of the commands 'ip link' and 'ip addr'
    ip link
    ip addr
    I hidden some addresses that might be needed to be kept private. Grey colour is a MAC address, red (only a part hidden) is an ip address, and pink do not know what is (looks like written in hex numbers).
    p0x8 wrote:
    - can you still access the internet when you boot the virtual machine using the installation ISO?*
    * I ask this because you seem to have changed the VirtualBox network adapters settings in Windows, something I would strongly advise against unless you know what you are doing - which is obviously not the case.
    Yes (3 packets sent, 1 lost, 2 received).
    chris_l wrote:
    No, I didn't mean to install it right away: you can boot the live cd and only configure internet on the live environment, without installing anything or messing with partitions. (your system will remain unchanged)
    The porpouse is just to discard virtualbox as source of problem
    I can access the Internet when I boot the live CD. However, I am not sure what you do mean saying to boot live cd without VB (it is probably, because you think the Internet is down also when the live CD is booted?).
    It struck my mind that the provided Internet is controlled by a MAC address by my ISP. Wrote ipconfig /all to find out VB's internet connection, and added a second physical address to the list of MAC addresses on my ISP website. Did not help.
    Last edited by decas (2012-12-14 20:05:38)

  • Can not ping oracle linux vm in Virtual Box from my host

    Hy
    I have setup oracle linux 7 on virtual box including vboxadditions.
    But I can not ping this maschine from outside ( it works for my other vm oel 5.8 )
    I did systemctl stop filewall.service
    Here my Network konfiguration inside my oel7 vm:
    /etc/sysconfig/network-scripts/ifcfg-enp0s8
    TYPE=Ethernet
    BOOTPROTO=none
    DEFROUTE=yes
    IPV4_FAILURE_FATAL=no
    IPV6INIT=no
    IPV6_AUTOCONF=yes
    IPV6_DEFROUTE=yes
    IPV6_FAILURE_FATAL=no
    NAME=public
    UUID=388ee413-55e9-45e1-be1d-4f5eedc402f3
    ONBOOT=yes
    IPADDR0=10.20.50.101
    PREFIX0=24
    IPV6_PEERDNS=yes
    IPV6_PEERROUTES=yes
    HWADDR=08:00:27:5F:87:91
    Can anyone help?
    Thanks
    Peter Schlaeger

    Hi,
    Before discussing the network configuration of Oracle Linux 7 (By the way; it seams correct), lets talk about the VirtualBox network configuration, So the Network adapter of your VM can be attached to {NAT, Bridged Adapter, Internal Network, Host-only Adapter, ...}, what is the Adapter attached to your NIC?
    Make sure the Network Adapter is the same as the your other VM (OL 5.8).
    Best regards

  • Hyper-V 'Insufficient system resources exist to complete the requested service' after turning hypervisorlaunchtype off and back to auto

    Hello everybody,
    I've looked far and wide for anybody who has experienced the issue that I am currently dealing with in hopes of not duplicating an already answered question. I found nothing, but please forgive me if it slipped by me.
    My issue began after installing VirtualBox to virtualize one of my favorite Linux OS's. Of course, I changed the BCD hypervisorlaunch type to 'off' so I could take advantage of HAV. Everything went great with Virtualbox, and my OS was running perfectly smoothly.
    Today, I needed to boot into one of my Windows virtual machines in Hyper-V. I changed the hypervisorlaunchtype to 'auto' in BCD and rebooted my machine.
    At this point, everything seemed normal. Windows took a few seconds longer to reboot and gave me a message about making configuration changes. After reboot, I logged into my PC and fired up Hyper-V. While one of my VM's was booting, I received multiple errors
    about why my VM couldn't boot - every single aspect of my VM was getting an error. I am getting 'Failed to allocate resources' errors, 'Insufficient system resources exist to complete the requested service' errors, 'could not find virtual switch' errors.
    It seems like they hypervisorlaunchtype did not actually change, but when I tried VirtualBox I received a 'VT-X is not available' error, so Hyper-V has taken ownership of that part of the chip. I rebooted another time after that, then a cold boot after that.
    It seems like I'm missing something pretty obvious, but I can't find any information on what it might be. I've never had any issues like this before, and have been using Hyper-V on this laptop for around 9 months. Any help would be greatly appreciated!
    I'm running Windows 8.1 Pro x64, 8GB DDR3, Intel i7. Guest machines included Windows XP, Windows 7 and Windows 8.

    The virtualbox networking stack is not compatible (I know that).
    Beyond that, details could only explain what else VirtualBox is locking.
    Brian Ehlert
    http://ITProctology.blogspot.com
    Learn. Apply. Repeat.
    Disclaimer: Attempting change is of your own free will.

  • Oracle Linux and SSH

    Hallo!
    I have a MacBook Pro 64 bit Version: 10.8.5 .
    I installed VirtualBox 4.3.4 on it.
    I used to install Debian Guest OSs.
    I used under Network 'NAT' with Port Forwarding
    There I mapped the Port 22 of the Guest OS with 60xx Ports.
    Then I opened the shell on my Mac and did a ssh connection for example in the following way:
    ssh -p 6011 root@localhost
    And it worked always fine.
    Then I installed Oracle Linux6 on my VirtualBox.
    And I did a Port Mapping: Port 22 on Oracle Linux with 6017 on my Mac.
    When I do
    ssh -p 6017 root@localhost
    it comes
    ssh_exchange_identification: Connection closed by remote host
    I think that has anything to do with the configuration of /etc/ssh/sshd_config?!
    Can anybody show me how this file should look like?
    Or do I have another problem?
    Thanks for any help!
    Gerhard

    Hi Dude!
    Thanks for your comments!
    I use 'bridged network adapter' if I want to connect from my 'Guest'-OS to the Internet.
    In my case I want to configure my Mac with its OSes as a 'Stand-Alone' Machine
    (I live in Mexiko on the Countryside and often I don't have connection to the Internet).
    That means, that my Mac is my Client and my Host-Server at the same time.
    I install a database on my 'Guest OS', start my 'Guest OS' and that all.
    All the rest I want to do, is to access to my 'Guest OS' from my Mac.
    I do all my SQL, PL/SQL and DBA stuff from Oracle SQL Developer installed on my Mac.
    I work with APEX and I access to the Database installed on my OS via my Browser installed on my Mac.
    And for any work on my Guest Linux OS, I do that with my Mac Shell.
    I did the same for many time with my Linux Guest OSes Debian and Ubuntu.
    And it worked always fine.
    But I never tried it with RedHat Systems.
    I compared my /etc/ssh/sshd_config of my Oracle Linux OS with /etc/ssh/sshd_config of my Debian OS.
    And the configuration is very different.
    So I don't think, that it is a problem of my VirtualBox Network Configuration.
    If it would be a problem of my VirtualBox Network Configuration, why does it run with my Debian OSes without problems?
    Thanks for any help!
    Gerhard

  • Network card doesn't start automatic on virtualbox

    Hi,
    I came back at Arch after a long time!
    I try to install on virtualbox with 2 network: first NAT (eth0) and second host-only (eth1)  but at each reboot my eth0 not start.
    My rc.conf
    # Network
    # interface=eth0
    # address=10.0.2.15
    # netmask=255.255.255.0
    # gateway=10.0.2.2
    interface=eth0
    address=10.0.2.15
    netmask=255.255.255.0
    gateway=10.0.2.2
    interface=eth1
    address=192.168.56.101
    netmask=255.255.255.0
    After boot:
    [root@arch ~]# ip addr
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
    valid_lft forever preferred_lft forever
    3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 08:00:27:0b:65:9e brd ff:ff:ff:ff:ff:ff
    inet 192.168.56.101/24 brd 192.168.56.255 scope global eth1
    inet6 fe80::a00:27ff:fe0b:659e/64 scope link
    valid_lft forever preferred_lft forever
    After dhcpcd eth0
    dhcpcd[378]: version 5.6.2 starting
    dhcpcd[378]: eth0: carrier lost
    dhcpcd[378]: eth0: carrier acquired
    dhcpcd[378]: eth0: sending IPv6 Router Solicitation
    dhcpcd[378]: eth0: sendmsg: Cannot assign requested address
    dhcpcd[378]: eth0: rebinding lease of 10.0.2.15
    dhcpcd[378]: eth0: acknowledged 10.0.2.15 from 10.0.2.2
    dhcpcd[378]: eth0: checking for 10.0.2.15
    dhcpcd[378]: eth0: sending IPv6 Router Solicitation
    dhcpcd[378]: eth0: leased 10.0.2.15 for 86400 seconds
    dhcpcd[378]: forked to background, child pid 415
    [root@arch ~]# ip addr
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
    valid_lft forever preferred_lft forever
    2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 08:00:27:78:c6:d7 brd ff:ff:ff:ff:ff:ff
    inet 10.0.2.15/24 brd 10.0.2.255 scope global eth0
    inet6 fe80::a00:27ff:fe78:c6d7/64 scope link
    valid_lft forever preferred_lft forever
    3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 08:00:27:0b:65:9e brd ff:ff:ff:ff:ff:ff
    inet 192.168.56.101/24 brd 192.168.56.255 scope global eth1
    inet6 fe80::a00:27ff:fe0b:659e/64 scope link
    valid_lft forever preferred_lft forever
    I have already try to set eth0 dhcp in rc.conf:
    interface="eth0"
    address=
    netmask=
    gateway=
    but eth0 after reboot isn't up.
    Where is the mistake??
    Thanks,
    Mirr0r

    During your absence there were a lot of changes, rolling as usual  . I guess.
    One of those was that multiple interfaces in rc.conf are not supported anymore. You can use "netcfg" profiles now for that. Have a look at the new wiki and the frontpage news.

  • Network Adapter no longer displays in VirtualBox - Resolved

    Hi,
    I'm running VirtualBox 4.1.22 on a Windows 7 laptop and have had the Developer Days image running successfully in the past. It was set up using a Bridged Adapter.
    Recently, I've been working on setting up some new Virtual Machines and now, for some reason, my adapter does not display. This prevents my Developer Days VM from starting up, due to the error:
    "Nonexistent host networking interface, name 'Intel(R) Centrino(R) Advanced-N 6250 AGN' (VERR_INTERNAL_ERROR)."
    The adapter and network connection using the 6250 that I'm attempting to bridge is still working fine.
    Does anybody have any suggestions on how to get VirtualBox to recognize my adapter again?
    Thanks in advance.
    Edited by: mattph on Oct 30, 2012 10:53 AM

    Issue Resolved!
    During my attempts last week to configure another VM, I had encountered network issues. It looks like I had disabled the Virtual Box Bridged Networking Adapter. I just re-enabled it, and now the adapter shows back up in VirtualBox.
    Thanks,
    Matt

  • Can't establish internet connection with NAT network in Oracle virtualbox

    Hi all,
    I am new to Oracle virtualbox. I have created a new virtual machine with Oracle linux 5.5 (64bit). I have enabled the NAT networking adaptor so as to access internet connection from the VM. But I am not able to do so.
    Here are the network settings in the VM
    1. Automatically obtain IP address settings with DHCP
    2. Firewalls are disabled.
    The 'eth0' device shows active status. The #ifconfig command lists "inet address" as 10.0.2.15.
    Please let me know if any additional configuration is required for establishing the internet connection in the VM.

    The NAT engine of Virtualbox automatically provides a router between the network interface of your host system and the virtual network interface of your guest OS and offers the same DNS servers to the guest that are configured on the host.
    For more information how it works, see http://www.virtualbox.org/manual/ch06.html#network_nat.
    The problem you are experiencing is most likely with the network configuration of your host system.

  • Bridge network with Virtualbox

    howdy guys,
    I've been playing with virtualbox a little bit, and found the blog of a guy who is using a virtualbox vm as a webserver.
    he lists these steps:
    tunctl -t tap0 -u user
    ;(where user is the user who runs VirtualBox)
    chmod 666 /dev/net/tun
    ;(or add user running VirtualBox to the 'tun' group, on MDV)
    brctl addbr br0
    ifconfig eth0 0.0.0.0 promisc
    ;(where eth0 is the interface to be bridged)
    brctl addif br0 eth0
    dhclient br0
    brctl addif br0 tap0
    ifconfig tap0 192.168.1.50 up
    ;(where 192.168.1.50 is an arbitrary unused
    ;IP in the same subnet as your local network)
    echo 1 > /proc/sys/net/ipv4/conf/tap0/proxy_arp
    route add -host 192.168.1.5 dev tap0
    ;(where 192.168.1.5 is the IP address of the host machine)
    arp -Ds 192.168.1.5 eth0 pub
    ;(where 192.168.1.5 is the IP address of the host machine)
    (from http://www.happyassassin.net/2007/02/06 … rtualbox/)
    I got brctl from the package "bridge-utils,"
    and tunctl from "uml_utilities."
    these steps almost work, except I can't use dhclient on br0, and on
    the host machine eth0 loses its address.
    Can someone give me some hints about how do accomplish this in an arch
    way, making use of /etc/conf.d/bridges, and rc.conf, or whatever?  thanks.

    Hi kant1. First I want to thank you for taking the time to respond and second I apologize for not posting earlier. I have been away from my computer these 2 days.
    Now,  to answer your questions:
    Have you tried running "top" and then running openoffice/xine?  Maybe they are using some other program that is getting hung up on the network change?
    I don't see anything strange.
    Also, did you try rebooting after making these changes?
    Yes, more than once
    Are you using the same address for the bridge as you are for your regular connection?  Or using dhcp for both?  (The link I posted uses dhcp, but you may need to specify the address if that's what you do for your regular connection)
    Does "ifconfig" show that eth0 (or whatever your regular ethernet connection is) does not have an ip address, but br0 does?  Does "brctl show" show that br0 has eth0 attached as an interface?
    Here is my ifconfig output. I believe this is how it should be
    $ ifconfig
    br0 Link encap:Ethernet HWaddr 00:17:31:83:C2:30
    inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:1307 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1394 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:1021200 (997.2 Kb) TX bytes:195531 (190.9 Kb)
    eth0 Link encap:Ethernet HWaddr 00:17:31:83:C2:30
    UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
    RX packets:1307 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1370 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:1041405 (1016.9 Kb) TX bytes:206215 (201.3 Kb)
    Interrupt:18
    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:129 errors:0 dropped:0 overruns:0 frame:0
    TX packets:129 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:8243 (8.0 Kb) TX bytes:8243 (8.0 Kb)
    and this is "brctl show"
    $ brctl show
    bridge name bridge id STP enabled interfaces
    br0 8000.00173183c230 no eth0
    and this is my network section in /etc/rc.conf
    lo="lo 127.0.0.1"
    BRIDGE_INTERFACES=(br0)
    bridge_br0=(eth0)
    br0="br0 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255"
    eth0="eth0 0.0.0.0 promisc"
    #eth0="eth0 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255"
    INTERFACES=(lo br0 eth0)
    # Routes to start at boot-up (in this order)
    # Declare each route then list in ROUTES
    # - prefix an entry in ROUTES with a ! to disable it
    gateway="default gw 192.168.1.1"
    ROUTES=(gateway)
    I don't know if it has any relevance but I was trying to see what is happening with wireshark. When I try to run soffice I see DNS queries to my ISP about arch.localdomain. These queries have naturally response "not found". arch is my host name.
    UPDATE: After posting this i added this line in /etc/hosts.
    127.0.0.1 arch.localdomain arch
    and now openoffice works again .
    But now I have 2 problems less significant
    1. Still xine doesn't work. I see a query for eth0.localdomain
    2. If I use the "Alt+F2" box in KDE and type i.e. calc it will still query my ISP for calc.localdomain.
    Last edited by insane (2007-06-16 14:14:21)

  • No network connection after install on a VirtualBox VM

    Hey guys, I am a relative newb to Arch, and linux in general for that matter. I'm working on a project with pogo plugs and Arch seems to be the best linux solution for those at the moment so I figured it would do me some good to get it running on my desktop so I can become more familiar with it.
    I'm attempting to install it on a VirtualBox vm following the beginners install guide. I get all the way through the install and reboot into my shiny new OS, but have run into the issue where I can't do any further package updates as I have lost my network connection. The beginners guide specifies a way to configure this so it it is persistent once the install is done.
    I can issue the systemctl enable "dhcpcd@<interface>.service" command with my interface as eth0 (verified by ip link) "[email protected]", but once I reboot into the fresh install ip link tells me my interface is actually enp0s3. If I rerun the dhcp enable command again with enp0s3 as the interface it executes without error, but I still do not have network.
    I tried using ifplugd during the install process during one of my go-arounds, but ifplugd was not able to install as none of the files appear to be available, perhaps that server is down?
    Can anyone shed some light on what I might be doing wrong? I'm guessing it's something very simple that I am missing, hopefully someone here can catch it.

    I was stuck at this problem, as in topic header. I looked at this post, thought that finally I found the solution(was referring to one more post). Then I tried following steps as mentioned in #3. OMG, I tried it for more than hour, couldn't get it working. Then i get one hint, i.e, the interface name is not enps03 but its enp0s3 ... Okay, again i tried, but still it did not work... this time i was little more cautious, so after few attempts, looked at my command, i had been typing [email protected], I don't know why such confusing naming conventions are followed, there are two files under /lib/systemd/system/ that are like dhcpd.* .. but this one particular file is dhcpcd@.*... well.. that's it. I just had to laugh at myself.

Maybe you are looking for

  • Questions on notifivation and fonts

    just upgrading to this phone from a blacberry.. 2 questions for now 1. how do I change the font size for text? text is too small for sms/mms,,  compose msg etc... 2. the notification volume won't adjust. I go into settings/sounds/volume. I have the 4

  • Connecting computer and home theatre to insignia TV

    I just bought a denon home theatre surround sound.  I have my insignia TV connected to my XBOX, blu ray, and computer.  Is there some way I could connect all these things to my TV and have them play through my surround sound?  Basically can I use my

  • Recaluculation of taxes at item level based on the value given in ZZ field

    Dear all, We have added a custom field for ALT BP TAX Grp at item level of service order. Whenever user changes the BP Tax Grp using this field at item level, we want the system to re-determine the taxes based on this new value of BP tax group bypass

  • How do i play a game after i install it on my powermac?

    i installed a game on my powermac ,so how do i open it to play it?

  • How to unregister nokia unlimited subscription

    Hey! ..i have problem in songs downloading. Plz tell me to get rid off it.. nd also i update my phone and restart it several time but i m getting the same error.. (aCtivation error) ....plz tell me how to solve this error...