VPN Remote Access on ASA5510 version 7.1(2)
Hi folks,
I have surprising thing when firstly configure IPsec_ra on asa 5510 with asa version 7.1(2). I usually configure this on PIX platform and never failed.
I use standard VPN remote access configuration with using provided default tunnel group.
Bellow is the configuration:
username xxx password xxx
ip local pool VPN_POOL 192.168.21.1-192.168.21.100 mask 255.255.255.0
isakmp enable Outside
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set ESP-3DES-MD5
crypto map vpnmap 1 ipsec-isakmp dynamic dyn1
crypto map vpnmap interface Outside
tunnel-group DefaultRAGroup general-attributes
address-pool VPN_POOL
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key xxx
I have enable command "sysopt connection permit-vpn", here i didn't find "permit-ipsec". Are those the same thing?
I have issued debug crypto ipsec and isakmp but does not give me enough information for configuartion error.
Aug 13 11:07:33 [IKEv1]: Group = DefaultRAGroup, IP = **.**.**.**, Removing peer from peer table failed, no match!
Aug 13 11:07:33 [IKEv1]: Group = DefaultRAGroup, IP = **.**.**.**, Error: Unable to remove PeerTblEntry
What is missing here? Please advice...
fyi: I use cisco vpn client v4.8.
Dear All ,
Since last 8 days i am also facing the same problem while configuring Remote Access VPN on ASA 5510
Error Message from ASA syslog while client making requset to connect :-
Group = AUTOMATION_TG, IP = 210.212.172.91, Error: Unable to remove PeerTblEntry
Group = AUTOMATION_TG, IP = 210.212.172.91, Removing peer from peer table failed, no match!
================This is the show run of my running configuration =======================
: Saved
PIX Version 7.2(2)
hostname ciscoasa
domain-name default.domain.invalid
names
interface Ethernet0
nameif Inside
security-level 100
ip address 10.210.3.254 255.255.255.0
interface Ethernet1
nameif Outside
security-level 0
ip address 210.212.172.94 255.255.255.0
interface Ethernet2
shutdown
no nameif
no security-level
no ip address
boot system flash:/asa722-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list Inside_nat0_outbound extended permit ip 10.210.3.0 255.255.255.0 172.16.1.0 255.255.255.240
access-list AUTOMATION_TG_splitTunnelAcl standard permit 10.210.3.0 255.255.255.0
pager lines 24
mtu Inside 1500
mtu Outside 1500
ip local pool VPN_POOL 172.16.1.1-172.16.1.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image flash:/asdm-522.bin
no asdm history enable
arp timeout 14400
nat (Inside) 0 access-list Inside_nat0_outbound
route Outside 0.0.0.0 0.0.0.0 210.212.172.95 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
group-policy AUTOMATION_TG internal
group-policy AUTOMATION_TG attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value AUTOMATION_TG_splitTunnelAcl
username automation1 password auto1 privilege 0
username automation1 attributes
vpn-group-policy AUTOMATION_TG
username cisco password cisco
http server enable
http 10.15.1.0 255.255.255.0 Outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map Outside_dyn_map 20 set pfs
crypto dynamic-map Outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map Outside_dyn_map 40 set pfs
crypto dynamic-map Outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto map Outside_map 65535 ipsec-isakmp dynamic Outside_dyn_map
crypto map Outside_map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group AUTOMATION_TG type ipsec-ra
tunnel-group AUTOMATION_TG general-attributes
address-pool VPN_POOL
default-group-policy AUTOMATION_TG
tunnel-group AUTOMATION_TG ipsec-attributes
pre-shared-key automation
tunnel-group-map default-group AUTOMATION_TG
telnet timeout 5
ssh timeout 5
console timeout 0
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Rergards
Sandeep Kadam
Network Specialist
Similar Messages
-
Cisco ASA disable command line interface (CLI) vor VPN Remote Access users
Hi,
I have local database for a couple of VPN Remote Access users on our Cisco ASA 5510 firewall. When adding users i asigned them the privilege leve 0. Is it possible to completly disable CLI for theses users as they will only be using VPN Remote Access and do not need to access the appliance cli.
Thanks in advance.
Kind Regards,
MarcoHi,
We will need to use the vpn-filter or the ssh command to block ssh from the vpn pool.
Regards,
Vivek -
Remote Access VPN - add new internal IP
Hi
I have a existing Cisco VPN client configuration into ASA 5510 for remote access.
Group name : ISETANLOT10
Group password : xxxx
IP pool : lot10ippool, 172.27.17.240 - 172.27.17.245
enycrption : 3DES
authentication : SHA
the connection was successful and i was able to ping to the internal server of 172.47.1.10.
Now there is request for the same VPN remote access to be able to ping access a new server inside LAN, 172.57.1.10 & 172.57.1.20
But with the same VPN access, i was unable to ping both new IP.
How can i add in the both IP to be able to ping using the same remote access VPN config?
I attached below existing config (edited version)
===
: Saved
ASA Version 8.0(4)
hostname asalot10
names
name 172.17.100.22 NAVNew
name 172.27.17.215 NECUser
name 172.47.1.10 NarayaServer description Naraya Server
name 62.80.122.172 NarayaTelco1
name 62.80.122.178 NarayaTelco2
name 172.57.1.10 IPVSSvr description IPVSSvr
name 122.152.181.147 Japan01
name 122.152.181.0 Japan02
name 175.139.156.174 Outside_Int
name 178.248.228.121 NarayaTelco3
name 172.67.1.0 VCGroup
name 172.57.1.20 IPVSSvr2
object-group service NECareService
description Remote NECareService
service-object tcp eq https
service-object tcp eq ssh
service-object icmp echo-reply
access-list inside_access_in extended deny ip any Japan02 255.255.255.0
access-list inside_access_in extended permit ip VCGroup 255.255.255.0 any
access-list inside_access_in extended deny tcp object-group PermitInternet any object-group torrent1
access-list inside_access_in extended permit ip object-group PermitInternet any log disable
access-list inside_access_in extended permit ip host NarayaServer any log disable
access-list inside_access_in extended permit ip host IPVSSvr any
access-list inside_access_in extended permit ip host NAVNew any log disable
access-list inside_access_in extended permit ip host 172.17.100.30 any
access-list outside_access_in extended permit object-group NECareService object-group NECare any
access-list outside_access_in extended permit ip object-group DM_INLINE_NETWORK_1 host NarayaServer
access-list outsidein extended permit tcp any host Outside_Int eq https
access-list outsidein extended permit object-group rdp any host Outside_Int log debugging
access-list outsidein extended permit tcp object-group DM_INLINE_NETWORK_2 host Outside_Int eq 8080
access-list outsidein extended permit ip object-group DM_INLINE_NETWORK_3 host IPVSSvr
access-list inside_mpc extended permit object-group TCPUDP any any eq www
access-list inside_mpc extended permit tcp any any eq www
access-list inside_nat0_outbound extended permit ip any 172.27.17.240 255.255.255.248
access-list inside_nat0_outbound extended permit ip host NarayaServer object-group Nry_Png
access-list inside_nat0_outbound extended permit ip host IPVSSvr2 172.27.17.240 255.255.255.248
access-list outside_cryptomap extended permit ip object-group Naraya_Png object-group Nry_Png
global (outside) 10 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 10 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 8080 NarayaServer 8080 netmask 255.255.255.255
static (inside,outside) tcp interface 3389 NAVNew 3389 netmask 255.255.255.255
static (inside,outside) tcp interface ssh IPVSSvr2 ssh netmask 255.255.255.255
access-group outsidein in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 175.139.156.173 1
route inside 172.17.100.20 255.255.255.255 172.27.17.100 1
route inside NAVNew 255.255.255.255 172.27.17.100 1
route inside 172.17.100.30 255.255.255.255 172.27.17.100 1
route inside NarayaServer 255.255.255.255 172.27.17.100 1
route inside 172.47.1.11 255.255.255.255 172.27.17.100 1
route inside VCGroup 255.255.255.0 172.27.17.100 1
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime seconds 28800
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 218.x.x.105
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 1 set security-association lifetime seconds 28800
crypto map outside_map 1 set security-association lifetime kilobytes 4608000
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
group-policy ISETANLOT10 internal
group-policy ISETANLOT10 attributes
dns-server value 172.27.17.100
vpn-tunnel-protocol IPSec l2tp-ipsec
username nectier3 password dPFBFnrViJi/LGbT encrypted privilege 0
username nectier3 attributes
vpn-group-policy ISETANLOT10
username necare password BkPn6VQ0VwTy7MY7 encrypted privilege 0
username necare attributes
vpn-group-policy ISETANLOT10
username naraya password pcGKDau9jtKgFWSc encrypted
username naraya attributes
vpn-group-policy ISETANLOT10
service-type nas-prompt
tunnel-group ISETANLOT10 type remote-access
tunnel-group ISETANLOT10 general-attributes
address-pool lot10ippool
default-group-policy ISETANLOT10
tunnel-group ISETANLOT10 ipsec-attributes
pre-shared-key *
tunnel-group 218.x.x.105 type ipsec-l2l
tunnel-group 218.x.x.105 ipsec-attributes
pre-shared-key *
tunnel-group ivmstunnel type remote-access
tunnel-group ivmstunnel general-attributes
address-pool lot10ippool
tunnel-group ivmstunnel ipsec-attributes
pre-shared-key *
!=====The remote access VPN should allow the connection but I am guessing your ASA doesn't know how to route to the two new destinations.
You have a name and static route for the working server at 172.47.1.10:
name 172.47.1.10 NarayaServer description Naraya Server
route inside NarayaServer 255.255.255.255 172.27.17.100 1
..but no equivalent for the two new hosts. As a result, any traffic from the ASA destined for them will attempt to use the default route (via the outside interface).
If you add:
route inside 172.57.1.10 255.255.255.255 172.27.17.100
route inside 172.57.1.20 255.255.255.255 172.27.17.100
(assuming that's your correct gateway), it should work. -
Help with Remote access VPN on Cisco router 3925 via Dialer Interface
Hi Everybody,
I need help for my work now, I appreciate if someone can fix my problem.I have a Cisco router 3925 and access Internet via PPPoE link. I want config VPN Remote Access and using software Cisco VPN client. But it doesn't work.. Here my config router :
HUNRE#show running-config
Building configuration...
Current configuration : 5515 bytes
! No configuration change since last restart
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname HUNRE
boot-start-marker
boot-end-marker
enable secret 5 $1$vEFw$rLfvLglzUgddCVwXDx03K.
enable password cisco
aaa new-model
aaa session-id common
crypto pki trustpoint TP-self-signed-1050416327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1050416327
revocation-check none
rsakeypair TP-self-signed-1050416327
crypto pki certificate chain TP-self-signed-1050416327
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31303530 34313633 3237301E 170D3134 30393235 31313534
31395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30353034
31363332 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CC79 74FCFABE 81183B70 5A9F4A53 EB609754 7D5F8587 9150B76E 3207A86E
5B65F9E9 6CDAC21A 6D69221D 1FF61632 14763308 43B2A1CC 8EE5ABAC EF07530E
3F0D35FE F08C955B 60B52B92 F8F54D53 DD6DD623 01F83493 02F9C49A F0C3483D
3B48A008 8D96700E 88924BFE DE00201B DE5965DE 32898CAD 9012AB55 76B6F39B
2D470203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14C3418C BC35F3D9 B26B2475 2BB5F826 060525AB B3301D06
03551D0E 04160414 C3418CBC 35F3D9B2 6B24752B B5F82606 0525ABB3 300D0609
2A864886 F70D0101 05050003 81810070 AC7C26C6 4606A551 1A3FD6C5 2A5AEAE8
35DAC86E F8885E26 51F6EEAE 7565D3AA D532C8F3 55F6656F D103F38C 8FBDE7F1
83E77143 76469040 7FEA41E8 14963DB3 F7F28EA0 C5F2F42C B186B75C AAB04900
15F9CB38 A16964F5 4E7B4378 35041AA8 AE8EC181 D58D6A62 676E286A 7B9D80E6
35A0B9FB FB76E976 3D2A19D7 006078
quit
ip name-server 210.245.1.253
ip name-server 210.245.1.254
ip cef
no ipv6 cef
multilink bundle-name authenticated
vpdn enable
vpdn-group 1
vpdn-group 2
license udi pid C3900-SPE100/K9 sn FOC1823839B
license boot module c3900 technology-package securityk9
username cisco privilege 15 secret 5 $1$aAjB$D3iLyPFTE7O1bHPnKSJcH0
username kdhong privilege 15 secret 5 $1$nfyX$FO1BPTabCUaE6uKQwpLT.1
redundancy
track 1 ip sla 1 reachability
track 2 ip sla 2 reachability
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group VPN-HUNRE
key hunre
dns 8.8.8.8
domain hunre
pool IP-VPN
acl 199
max-users 100
crypto ipsec transform-set encrypt-method-1 esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map DYNMAP 1
set transform-set encrypt-method-1
crypto map VPN client configuration address respond
crypto map VPN 65535 ipsec-isakmp dynamic DYNMAP
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip mtu 1492
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
interface GigabitEthernet0/1
description FPT
no ip address
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface GigabitEthernet0/2
description Connect to CMC
no ip address
ip mtu 1442
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
no cdp enable
interface Dialer1
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp dns request
crypto map VPN
interface Dialer2
description Logical ADSL Interface 2
ip address negotiated
ip mtu 1442
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1344
dialer pool 2
dialer-group 2
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp address accept
no cdp enable
ip local pool IP-VPN 10.252.252.2 10.252.252.245
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 10 interface Dialer1 overload
ip nat inside source list 11 interface Dialer2 overload
ip nat inside source static 10.159.217.10 interface Dialer1
ip nat inside source list 199 interface Dialer1 overload
ip nat inside source static tcp 10.159.217.10 80 210.245.54.49 80 extendable
ip nat inside source static tcp 10.159.217.10 3389 210.245.54.49 3389 extendable
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.159.217.0 255.255.255.0 192.168.1.8
ip sla auto discovery
ip sla responder
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
access-list 10 permit any
access-list 11 permit any
access-list 101 permit icmp any any
access-list 199 permit ip any any
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
transport input all
line vty 5 15
password cisco
transport input all
scheduler allocate 20000 1000
ntp master
end
However, I cannot ping interfac Dialer 1. I using Cisco vpn client software ver 5.0.07.0290.
Hopeful for your answers !
ThanksHi David Castro,
Thanks for your answer,
I configed following your guide, but it have not worked yet. I saw that I cannot ping IP gateway Internet . I using ADSL Internet and config PPPoE and my router receive IP from ISP. Here show ip int brief :
GigabitEthernet0/0 192.168.1.1 YES NVRAM up up
GigabitEthernet0/1 unassigned YES NVRAM up up
GigabitEthernet0/2 unassigned YES NVRAM up up
Dialer1 210.245.54.49 YES IPCP up up
Dialer2 101.99.7.73 YES IPCP up up
NVI0 192.168.1.1 YES unset up up
Virtual-Access1 unassigned YES unset up up
Virtual-Access2 unassigned YES unset up up
Virtual-Access3 unassigned YES unset up up
But I cannot ping Interface Dialer 1, so may be VPN is does not worked. Do you have some ideal ?
Thanks very much ! -
What is/are the best Remote Access/VPN services for my Mac system?
2009 Macbook Pro
2009 Macbook
2010 iMac
2 iPad 2s
2 iPhone 4s
Computers on Snow Leopard
iOS 5
Everything is updated
I want :
1. to have everything working together, with remote access from anywhere on the internet, file sharing, streaming & transfer.
2. the security of a VPN connection.
I will soon update my existing router w/an Airport Extreme. What VPN/Remote Access client(s) should I get? Is there one solution for both jobs, or do I need to get more than one service? I have looked at LogMeIn, Witopia. Thanks for the help.I've been down this road and settled on a much simpler solution...
VPNs are ok... but the performance is bad, they send TCP packets inside TCP packets... which is a bad thing, some connections completely break down. security is o-k, but openVPN is much better yet more complicated to set up. Also you have to go through all the mess of setting up the server.
I tried using VPNs for a while, and then instead settled with tunneling specific connections over ssh... it is more secure and elegant, there is no server setup, however it is not seemless.. you have to set up the connections/ports individually each time, this can get messy if you want access to lots of things at once.
I eventually came accross sshuttle, and this is what i have stuck with because it's just bloody great... it's like a VPN but uses SSH. So you don't have to set up a VPN server... you just need access to an ssh server (i.e your home mac with "remote login" (ssh) enabled, and your router to foward ssh requests to that machine).
not only do you not have to mess around with server configs, but it also give far better performance, stability, and the security of ssh (i.e whichever cypher you want). This is because unlike VPN, sshuttle pulls the TCP packets apart before sending them over SSH (which is allready using TCP) and then re-assembles them the other side with python. the result is comparably better performance and stability than VPN protocols.
you can route individual IPs from the servers subnet, or tell it to automatically find and merge all host names / IPs it can find with your current subnet.
Theory of Operation
sshuttle is not exactly a VPN, and not exactly port forwarding. It's kind of both, and kind of neither.
It's like a VPN, since it can forward every port on an entire network, not just ports you specify. Conveniently, it lets you use the "real" IP addresses of each host rather than faking port numbers on localhost.
On the other hand, the way it works is more like ssh port forwarding than a VPN. Normally, a VPN forwards your data one packet at a time, and doesn't care about individual connections; ie. it's "stateless" with respect to the traffic. sshuttle is the opposite of stateless; it tracks every single connection.
You could compare sshuttle to something like the old Slirp program, which was a userspace TCP/IP implementation that did something similar. But it operated on a packet-by-packet basis on the client side, reassembling the packets on the server side. That worked okay back in the "real live serial port" days, because serial ports had predictable latency and buffering.
But you can't safely just forward TCP packets over a TCP session (like ssh), because TCP's performance depends fundamentally on packet loss; it must experience packet loss in order to know when to slow down! At the same time, the outer TCP session (ssh, in this case) is a reliable transport, which means that what you forward through the tunnel never experiences packet loss. The ssh session itself experiences packet loss, of course, but TCP fixes it up and ssh (and thus you) never know the difference. But neither does your inner TCP session, and extremely screwy performance ensues.
sshuttle assembles the TCP stream locally, multiplexes it statefully over an ssh session, and disassembles it back into packets at the other end. So it never ends up doing TCP-over-TCP. It's just data-over-TCP, which is safe.
Anyway, you can find it on github here https://github.com/apenwarr/sshuttle
if you uncomfortable using the command line, someone has also bundled it into an app here: https://github.com/apenwarr/sshuttle/commits/dist/macos
IMPORTANT, the latest version invokes a bug in one of apple's drivers after a while which causes a kernel panic, (this isn't the same as the bug where you have to reset your network interface like it says in the readme, this WILL cause a kernel panic) stick with version 0.53 untill ether Apple fixes the bug, or sshuttle stops antagonising it. 0.53 works perfectly at the moment. you can ether install git and clone the specific version or download the 0.53 app here instead:
http://mac.softpedia.com/progDownload/sshuttle-Download-97917.html
alternatively, if your loging in from linux there aren't any problems with 0.60 because the system would have different dirvers of course.
One last note... you said you wanted everything to work together, one thing that will not work over VPNs, SSH, and sshuttle is bojour... this is significant because things like AFP shares wont pop up automatically, you will have to specify them ... i.e command+k in finder and type AFP://192.168.0.x or VNC://192.168.0.x etc this is because none of these options support multicasting which bonjour requires. This isn't such a big deal so long as you know what services are available on your machine and how to manually connect to them (like i said above) -
Remote Access VPN - Unable to Access LAN / Inside Network
Hi,
I am facing a problem with Cisco ASA remote access VPN, the remote client is connected to VPN and receiving IP address but the client is not able to ping or telnet any internal network.
I have attached running configuration for your reference. Please let me know I miss any configuartion.
FW : ASA5510
Version : 8.0
Note : Site to Site VPN is working without any issues
Thanks
JamalHi,
Very nice network diagram
Are you saying that originally the VPN Client user is behind the Jeddah ASA?
If this is true wouldnt it be wiser to just use the already existing L2L VPN between these sites?
In real situation I think the VPN Client would only be needed when you are outside either Head Quarter or Jeddah Network. And since you tested it infront of the ASA and it worked there shouldnt be any problem.
Now to the reason why the VPN Client isnt working from behind the Jeddah ASA.
Can you check that the following configuration is found on the Jeddah ASA (Depending on the software level of the ASA the format of the command might change. I'm not 100% sure)
isakmp nat-traversal To enable NAT traversal globally, check that ISAKMP is enabled (you can enable it with the isakmp enable command) in global configuration mode and then use the isakmp nat-traversal command. If you have enabled NAT traversal, you can disable it with the no form of this command.
isakmp nat-traversal natkeepalive
no isakmp nat-traversal natkeepalive
Syntax Description
natkeepalive
Sets the NAT keep alive interval, from 10 to 3600 seconds. The default is 20 seconds.
Defaults
By default, NAT traversal (isakmp nat-traversal) is disabled.
Command Modes
The following table shows the modes in which you can enter the command:
Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System
Global configuration
Command History
Release
Modification
Preexisting
This command was preexisting.
7.2(1)
This command was deprecated. The crypto isakmp nat-traversal command replaces it.
Usage Guidelines Network Address Translation (NAT), including Port Address Translation (PAT), is used in many networks where IPSec is also used, but there are a number of incompatibilities that prevent IPSec packets from successfully traversing NAT devices. NAT traversal enables ESP packets to pass through one or more NAT devices.
The security appliance supports NAT traversal as described by Version 2 and Version 3 of the IETF "UDP Encapsulation of IPsec Packets" draft, available at http://www.ietf.org/html.charters/ipsec-charter.html, and NAT traversal is supported for both dynamic and static crypto maps.
This command enables NAT-T globally on the security appliance. To disable in a crypto-map entry, use the crypto map set nat-t-disable command.
Examples
The following example, entered in global configuration mode, enables ISAKMP and then enables NAT traversal with an interval of 30 seconds:
hostname(config)# isakmp enable
hostname(config)# isakmp nat-traversal 30
- Jouni -
Remote access VPN Users not able to see local lan or internet
We are setting up a ASA5510. Right now our users can login to the vpn but can't access the internal Lan or internet.
Below is the config. Any help or insight would be greatly appreciated. Thanks
Cryptochecksum: dd11079f e4fe7597 4a8657ba 1e7b287f
: Saved
: Written by enable_15 at 11:04:57.005 UTC Wed Apr 22 2015
ASA Version 9.0(3)
hostname CP-ASA-TOR1
enable password m.EmhnDT1BILmiAY encrypted
names
ip local pool CPRAVPN 10.10.60.1-10.10.60.40 mask 255.255.255.0
interface Ethernet0/0
nameif Outside
security-level 0
ip address 63.250.109.211 255.255.255.248
interface Ethernet0/1
nameif Inside
security-level 100
ip address 10.10.10.254 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
ftp mode passive
object network net-local
subnet 10.10.10.0 255.255.255.0
object network net-remote
subnet 10.10.1.0 255.255.255.0
object network NETWORK_OBJ_10.10.10.0_24
subnet 10.10.10.0 255.255.255.0
object network NETWORK_OBJ_10.10.60.0_26
subnet 10.10.60.0 255.255.255.192
access-list Outside_1_cryptomap extended permit ip 10.10.10.0 255.255.255.0 object net-remote
access-list CPRemoteVPN_splitTunnelAcl standard permit 10.10.10.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu Outside 1500
mtu Inside 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-731-101.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (Inside,Outside) source static net-local net-local destination static net-remote net-remote
nat (Inside,Outside) source static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 destination static NETWORK_OBJ_10.10.60.0_26 NETWORK_OBJ_10.10.60.0_26 no-proxy-arp route-lookup
nat (Inside,Outside) after-auto source dynamic any interface
route Outside 0.0.0.0 0.0.0.0 63.250.109.209 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.10.10.0 255.255.255.0 Inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Outside_map 1 match address Outside_1_cryptomap
crypto map Outside_map 1 set pfs group1
crypto map Outside_map 1 set peer 209.171.34.91
crypto map Outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Outside_map interface Outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev1 enable Outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy CPRemoteVPN internal
group-policy CPRemoteVPN attributes
dns-server value 10.10.10.12
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
split-tunnel-network-list value CPRemoteVPN_splitTunnelAcl
default-domain value carepath.local
split-dns value carepath.ca
split-tunnel-all-dns enable
msie-proxy method no-proxy
address-pools value CPRAVPN
username roys password jjiV7E.dmZNdBlFQ encrypted privilege 0
username roys attributes
vpn-group-policy CPRemoteVPN
tunnel-group 209.171.34.91 type ipsec-l2l
tunnel-group 209.171.34.91 ipsec-attributes
ikev1 pre-shared-key *****************
tunnel-group CPRemoteVPN type remote-access
tunnel-group CPRemoteVPN general-attributes
address-pool CPRAVPN
default-group-policy CPRemoteVPN
tunnel-group CPRemoteVPN ipsec-attributes
ikev1 pre-shared-key **********
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:dd11079fe4fe75974a8657ba1e7b287f
: endSorry for the delay but I was able to put that command in this morning. But still no Joy.
Here is the updated config. Perhaps I didn't put it in right.
domain-name carepath.ca
enable password m.EmhnDT1BILmiAY encrypted
names
ip local pool CPRAVPN 10.10.60.1-10.10.60.40 mask 255.255.255.0
interface Ethernet0/0
nameif Outside
security-level 0
ip address 63.250.109.211 255.255.255.248
interface Ethernet0/1
nameif Inside
security-level 100
ip address 10.10.10.254 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
ftp mode passive
dns server-group DefaultDNS
domain-name carepath.ca
object network net-local
subnet 10.10.10.0 255.255.255.0
object network net-remote
subnet 10.10.1.0 255.255.255.0
object network NETWORK_OBJ_10.10.10.0_24
subnet 10.10.10.0 255.255.255.0
object network NETWORK_OBJ_10.10.60.0_26
subnet 10.10.60.0 255.255.255.192
access-list Outside_1_cryptomap extended permit ip 10.10.10.0 255.255.255.0 object net-remote
access-list CPRemoteVPN_splitTunnelAcl standard permit 10.10.10.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu Outside 1500
mtu Inside 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-731-101.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (Inside,Outside) source static net-local net-local destination static net-remote net-remote
nat (Inside,Outside) source static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 destination static NETWORK_OBJ_10.10.60.0_26 NETWORK_OBJ_10.10.60.0_26 no-proxy-arp route-lookup
nat (Inside,Outside) after-auto source dynamic any interface
route Outside 0.0.0.0 0.0.0.0 63.250.109.209 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.10.10.0 255.255.255.0 Inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Outside_map 1 match address Outside_1_cryptomap
crypto map Outside_map 1 set pfs group1
crypto map Outside_map 1 set peer 209.171.34.91
crypto map Outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Outside_map interface Outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable Outside
crypto ikev1 enable Outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 10.10.10.0 255.255.255.255 Inside
telnet timeout 5
ssh 10.10.10.0 255.255.255.0 Inside
ssh timeout 5
console timeout 0
management-access Inside
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy CPRemoteVPN internal
group-policy CPRemoteVPN attributes
dns-server value 10.10.10.12
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value CPRemoteVPN_splitTunnelAcl
default-domain value carepath.local
split-dns value carepath.ca
split-tunnel-all-dns enable
msie-proxy method no-proxy
address-pools value CPRAVPN
username sroy password RiaBzZ+N4R7r5Fp/8RT+wg== nt-encrypted privilege 15
username roys password jjiV7E.dmZNdBlFQ encrypted privilege 0
username roys attributes
vpn-group-policy CPRemoteVPN
tunnel-group 209.171.34.91 type ipsec-l2l
tunnel-group 209.171.34.91 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group CPRemoteVPN type remote-access
tunnel-group CPRemoteVPN general-attributes
address-pool CPRAVPN
default-group-policy CPRemoteVPN
tunnel-group CPRemoteVPN ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:bbc0f005f1a075a4f9cba737eaffb6f2 -
Remote Access VPN Clients Cannot Access inside LAN
I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with. I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA. Thay can ping each other. The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10. I do not need split tunneling to be enabled. The active WAN interface is the one labeled outside_cable.
: Saved
ASA Version 8.2(1)
hostname ASA5505
domain-name default.domain.invalid
enable password eelnBRz68aYSzHyz encrypted
passwd eelnBRz68aYSzHyz encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.100.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group dataDSL
ip address 76.244.75.57 255.255.255.255 pppoe
interface Vlan3
nameif dmz
security-level 50
ip address 192.168.9.1 255.255.255.0
interface Vlan10
nameif outside_cable
security-level 0
ip address 50.84.96.178 255.255.255.240
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit intra-interface
object-group service Netbios udp
port-object eq 139
port-object eq 445
port-object eq netbios-ns
object-group service Netbios_TCP tcp
port-object eq 445
port-object eq netbios-ssn
object-group network DM_INLINE_NETWORK_1
network-object host 192.168.100.177
network-object host 192.168.100.249
object-group service Web_Services tcp
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
object-group network DM_INLINE_NETWORK_10
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_11
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_2
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_3
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_4
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_5
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_6
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_7
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_8
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_9
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network VPN
network-object 192.168.255.0 255.255.255.0
access-list outside_access_in extended permit icmp any host 76.244.75.61
access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp
access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp-data
access-list outside_access_in extended permit tcp any host 76.244.75.62 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.62 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.59 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.59 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.60 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.60 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.58 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.58 eq https
access-list dmz_access_in remark Quickbooks
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_6 host 192.168.100.5 eq 56719
access-list dmz_access_in remark Quickbooks range
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_7 host 192.168.100.5 range 55333 55337
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_8 host 192.168.100.5 eq 1434
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_9 host 192.168.100.5 eq 49398
access-list dmz_access_in remark QB
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_10 host 192.168.100.5 eq 8019
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_2 host 192.168.100.5 eq 2638
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_11 host 192.168.100.5 object-group Netbios
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_3 host 192.168.100.5 object-group Netbios_TCP
access-list dmz_access_in extended deny ip host 192.168.9.4 host 192.168.100.5 inactive
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_4 any
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_5 any
access-list dmz_access_in remark Printer
access-list dmz_access_in extended permit ip 192.168.9.0 255.255.255.0 object-group DM_INLINE_NETWORK_1
access-list dmz_access_in extended permit tcp 192.168.9.0 255.255.255.0 any object-group Web_Services
access-list dmz_access_in extended permit udp 192.168.9.0 255.255.255.0 any eq domain
access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.255.0 255.255.255.0 echo-reply
access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.100.0 255.255.255.0 echo-reply log disable
access-list dmz_access_in remark QB probably does not need any udp
access-list dmz_access_in extended permit udp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
access-list dmz_access_in remark QB included in other rule range
access-list dmz_access_in extended permit tcp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
access-list dmz_access_in remark May be required for Quickbooks
access-list dmz_access_in extended permit icmp host 192.168.9.4 host 192.168.100.5
access-list CAD_capture extended permit ip host 192.168.9.4 host 192.168.100.5
access-list CAD_capture extended permit ip host 192.168.100.5 host 192.168.9.4
access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 172.16.10.0 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 172.16.20.0 255.255.255.240
access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.100.0 255.255.255.0
access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.9.0 255.255.255.0
access-list dmz_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
access-list outside_cable_access_in extended permit icmp any host 50.84.96.182
access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp
access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp-data
access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq https
access-list Local_LAN_Access standard permit host 0.0.0.0
access-list vpnusers_spitTunnelACL extended permit ip 192.168.100.0 255.255.255.0 any
access-list nonat-in extended permit ip 192.168.100.0 255.255.255.0 172.16.20.0 255.255.255.0
pager lines 24
logging enable
logging buffered informational
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
mtu outside_cable 1500
ip local pool VPN_IP_range 192.168.255.1-192.168.255.10 mask 255.255.255.0
ip local pool VPN_Phone 172.16.20.1-172.16.20.10 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat-control
global (outside) 10 interface
global (outside_cable) 10 interface
nat (inside) 0 access-list nonat-in
nat (inside) 10 0.0.0.0 0.0.0.0
nat (dmz) 0 access-list dmz_nat0_outbound
nat (dmz) 10 0.0.0.0 0.0.0.0
static (inside,outside) 76.244.75.62 192.168.100.25 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.61 192.168.9.123 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.59 192.168.9.124 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.58 192.168.9.4 netmask 255.255.255.255 dns
static (inside,dmz) 192.168.100.0 192.168.100.0 netmask 255.255.255.0
static (dmz,outside) 76.244.75.60 192.168.9.10 netmask 255.255.255.255 dns
static (inside,outside_cable) 50.84.96.183 192.168.100.25 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.182 192.168.9.123 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.180 192.168.9.124 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.179 192.168.9.4 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.181 192.168.9.10 netmask 255.255.255.255 dns
access-group outside_access_in in interface outside
access-group dmz_access_in in interface dmz
access-group outside_cable_access_in in interface outside_cable
route outside_cable 0.0.0.0 0.0.0.0 50.84.96.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.100.0 255.255.255.0 inside
http 204.107.173.0 255.255.255.0 outside
http 204.107.173.0 255.255.255.0 outside_cable
http 0.0.0.0 0.0.0.0 outside_cable
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_cable_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_cable_map interface outside_cable
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp enable outside_cable
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet 192.168.100.0 255.255.255.0 inside
telnet timeout 5
ssh 192.168.100.0 255.255.255.0 inside
ssh 204.107.173.0 255.255.255.0 outside
ssh 204.107.173.0 255.255.255.0 outside_cable
ssh 0.0.0.0 0.0.0.0 outside_cable
ssh timeout 15
console timeout 0
vpdn group dataDSL request dialout pppoe
vpdn group dataDSL localname [email protected]
vpdn group dataDSL ppp authentication pap
vpdn username [email protected] password *********
dhcpd address 192.168.100.30-192.168.100.99 inside
dhcpd dns 192.168.100.5 68.94.156.1 interface inside
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.100.5
vpn-tunnel-protocol IPSec l2tp-ipsec
group-policy cad_supplies_RAVPN internal
group-policy cad_supplies_RAVPN attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value cad_supplies_RAVPN_splitTunnelAcl
group-policy VPNPHONE internal
group-policy VPNPHONE attributes
dns-server value 192.168.100.5
vpn-tunnel-protocol IPSec
split-tunnel-policy excludespecified
split-tunnel-network-list value Local_LAN_Access
client-firewall none
client-access-rule none
username swinc password BlhBNWfh7XoeHcQC encrypted
username swinc attributes
vpn-group-policy cad_supplies_RAVPN
username meredithp password L3lRjzwb7TnwOyZ1 encrypted
username meredithp attributes
vpn-group-policy cad_supplies_RAVPN
service-type remote-access
username ipphone1 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone1 attributes
vpn-group-policy VPNPHONE
username ipphone2 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone2 attributes
vpn-group-policy VPNPHONE
username ipphone3 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone3 attributes
vpn-group-policy VPNPHONE
username oethera password WKJxJq7L6wmktFNt encrypted
username oethera attributes
vpn-group-policy cad_supplies_RAVPN
service-type remote-access
username markh password nqH+bk6vj0fR83ai0SAxkg== nt-encrypted
username markh attributes
vpn-group-policy cad_supplies_RAVPN
tunnel-group DefaultRAGroup general-attributes
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group cad_supplies_RAVPN type remote-access
tunnel-group cad_supplies_RAVPN general-attributes
address-pool VPN_IP_range
default-group-policy cad_supplies_RAVPN
tunnel-group cad_supplies_RAVPN ipsec-attributes
pre-shared-key *
tunnel-group VPNPHONE type remote-access
tunnel-group VPNPHONE general-attributes
address-pool VPN_Phone
default-group-policy VPNPHONE
tunnel-group VPNPHONE ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 1500
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8b25ecc61861a2baa6d2556a3679cc7c
: endHi,
You have your "group-policy" set so that you have excluding some networks from being tunneled.
In this access-list named Local_LAN_Access you specify "0.0.0.0"
Doesnt this mean you are excluding all networks from being tunneled? In other words no traffic goes to your tunnel.
This access-list should only contain your local LAN network from where you are connecting with the VPN Client. If you dont need to access anything on your local LAN while having the VPN on, you don't even need this setting on. You could just tunnel all traffic instead of excluding some networks.
- Jouni -
Remote access vpn connects to 5505 but cannot ping any servers
I have a cisco 5505 and am trying to configure it with ASDM 6.4.
My vpn client connects ok to the network but I am unable to reach any of the servers.
I'm sure its a simple configuration issue as I don't have much experience with Cisco configuation.
Any suggestions on where to look would be much appreciated.
Thanks in advance
GrahamThanks Jennifer.
Running config:
Cryptochecksum: 21ec6d8c 73515258 ed808b45 e154b1c6
: Saved
: Written by admin at 17:42:19.318 GMT/IDT Thu Sep 20 2012
ASA Version 8.2(5)
hostname IS-18241
enable password p2SKmVPuBXX32cE encrypted
passwd 2KFnbXXKXX encrypted
names
name 78.129.xxx.xx IS-18223_External
name 192.168.100.2 IS-18223_Internal
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
interface Vlan1
nameif Inside
security-level 100
ip address 192.168.100.1 255.255.255.0
interface Vlan2
nameif Outside
security-level 0
ip address 78.129.xxx.xx 255.255.255.0
boot system disk0:/asa825-k8.bin
ftp mode passive
clock timezone GMT/IST 0
clock summer-time GMT/IDT recurring last Sun Mar 1:00 last Sun Oct 2:00
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list basic extended permit tcp any any eq 3389
access-list basic extended permit tcp any any eq ssh
access-list basic extended permit tcp any any eq www
access-list basic extended permit tcp any any eq 902
access-list basic extended permit tcp any any eq https
access-list basic extended permit icmp any any
access-list allow extended permit ip any any
access-list Inside_nat0_outbound extended permit ip any host IS-18223_Internal
access-list SplitTunnel standard permit 192.168.100.0 255.255.255.0
access-list Inside_nat_outbound extended permit ip 192.168.100.0 255.255.255.0 any
pager lines 24
logging enable
logging asdm informational
mtu Inside 1500
mtu Outside 1500
ip local pool RemoteAddressPool 192.168.100.100-192.168.100.150 mask 255.255.255.128
icmp unreachable rate-limit 1 burst-size 1
asdm location IS-18223_External 255.255.255.255 Inside
asdm location IS-18223_Internal 255.255.255.255 Inside
no asdm history enable
arp timeout 14400
global (Inside) 1 interface
global (Outside) 1 interface
nat (Inside) 0 access-list Inside_nat0_outbound
nat (Inside) 1 access-list Inside_nat_outbound
static (Inside,Outside) IS-18223_External IS-18223_Internal netmask 255.255.255.255
access-group allow in interface Inside
access-group allow out interface Inside
access-group basic in interface Outside
access-group allow out interface Outside
route Outside 0.0.0.0 0.0.0.0 78.129.xxx.x 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
http server enable
http 0.0.0.0 0.0.0.0 Outside
no snmp-server location
no snmp-server contact
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Outside_map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Outside
ssh timeout 60
ssh version 2
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
dns-server value 87.117.198.200 87.117.237.100
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SplitTunnel
username XX password uvgXvd9nQEHdkA73 encrypted privilege 15
username XX password 3CUtfh8r/IKb6DxX encrypted
username XX attributes
service-type remote-access
tunnel-group Remote type remote-access
tunnel-group Remote general-attributes
address-pool RemoteAddressPool
tunnel-group Remote ipsec-attributes
pre-shared-key 5|J5XX&6u*
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:21ec6d8c73515258ed808b45e154b1c6
: end -
Remote Access VPN Problem with ASA 5505
After about ~1 year of having the Cisco VPN Client connecting to a ASA 5505 without any problems, suddenly one day it stops working. The client is able to get a connection to the ASA and browse the local network for only about 30 seconds after connection. After that, no access is available to the network behind the ASA. I tried everything that I can think of to try and troubleshoot the problem, but at this point I am just banging my head against a wall. Does anyone know what could cause this?
Here is the running cfg of the ASA
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password xxxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxx encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http **.**.***.*** 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
And here is the logs from the Cisco VPN Client when it browses, then fails to browse the network behind the ASA:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600026
Attempting to find a Certificate using Serial Hash.
2 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600027
Found a Certificate using Serial Hash.
3 09:44:55.693 10/01/13 Sev=Info/6 GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
4 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100002
Begin connection process
5 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100004
Establish secure connection
6 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
7 09:45:02.802 10/01/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
8 09:45:02.818 10/01/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
9 09:45:02.865 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
10 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
11 09:45:02.896 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
12 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
13 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
14 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
15 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
16 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
17 09:45:02.927 10/01/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
18 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
19 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 10/01/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end is NOT behind a NAT device
21 09:45:02.927 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 09:45:02.943 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 09:45:02.943 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 09:45:02.943 10/01/13 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 09:45:03.037 10/01/13 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
26 09:45:03.037 10/01/13 Sev=Info/4 CM/0x63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
28 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
29 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
30 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
31 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
32 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
33 09:45:03.083 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
34 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
35 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
36 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
37 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
38 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
39 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
40 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
41 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
42 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
43 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
45 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
46 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0x00002710
47 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
48 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
49 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
50 09:45:03.146 10/01/13 Sev=Info/4 CM/0x63100019
Mode Config data received
51 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
52 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
53 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
54 09:45:03.177 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
55 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
56 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 1 seconds, setting expiry to 86399 seconds from now
57 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
58 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
59 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
60 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to **.**.***.***
61 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=967A3C93 OUTBOUND SPI = 0xAAAF4C1C INBOUND SPI = 0x3EBEBFC5)
62 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xAAAF4C1C
63 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 10/01/13 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
66 09:45:03.896 10/01/13 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
67 09:45:03.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 10/01/13 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
69 09:45:07.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**.**.***.*** 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 10/01/13 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
71 09:45:07.912 10/01/13 Sev=Info/4 CM/0x6310001A
One secure connection established
72 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 96.11.251.149. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 10/01/13 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
75 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
76 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
77 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x1c4cafaa into key list
78 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
79 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xc5bfbe3e into key list
80 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
81 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
83 09:45:13.459 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
84 09:45:13.459 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205276
85 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
86 09:45:13.474 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
87 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205276, seq# expected = 107205276
88 09:45:15.959 10/01/13 Sev=Info/4 IPSEC/0x63700019
Activate outbound key with SPI=0x1c4cafaa for inbound key with SPI=0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
90 09:46:00.947 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205277
91 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
92 09:46:01.529 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
93 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205277, seq# expected = 107205277
94 09:46:11.952 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
95 09:46:11.952 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205278
96 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
97 09:46:11.979 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
98 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205278, seq# expected = 107205278
Any help would be appreciated, thanks!I made the change that you requested by moving the VPN pool to the 192.168.3.0 network. Unfortunately, now traffic isn't flowing to the inside network at all. I was going to make a specific route as you suggested, but as far as I can see the routes are already being created correctly on the VPN client's end.
Here is the route print off of the computer behind the (test) client:
===========================================================================
Interface List
21...00 05 9a 3c 78 00 ......Cisco Systems VPN Adapter for 64-bit Windows
10...00 15 5d 01 02 01 ......Microsoft Hyper-V Network Adapter
15...00 15 5d 01 02 02 ......Microsoft Hyper-V Network Adapter #2
1...........................Software Loopback Interface 1
13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter
16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2
23...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
69.61.228.178 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 On-link 96.11.251.149 261
96.11.251.149 255.255.255.255 On-link 96.11.251.149 261
96.11.251.255 255.255.255.255 On-link 96.11.251.149 261
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.1.0 255.255.255.0 On-link 192.168.1.3 261
192.168.1.3 255.255.255.255 On-link 192.168.1.3 261
192.168.1.255 255.255.255.255 On-link 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.3.1 192.168.3.70 100
192.168.3.0 255.255.255.0 On-link 192.168.3.70 261
192.168.3.70 255.255.255.255 On-link 192.168.3.70 261
192.168.3.255 255.255.255.255 On-link 192.168.3.70 261
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.1.3 261
224.0.0.0 240.0.0.0 On-link 96.11.251.149 261
224.0.0.0 240.0.0.0 On-link 192.168.3.70 261
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.1.3 261
255.255.255.255 255.255.255.255 On-link 96.11.251.149 261
255.255.255.255 255.255.255.255 On-link 192.168.3.70 261
===========================================================================
Persistent Routes:
Network Address Netmask Gateway Address Metric
0.0.0.0 0.0.0.0 96.11.251.1 Default
===========================================================================
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
14 1020 ::/0 2002:c058:6301::c058:6301
14 1020 ::/0 2002:c058:6301::1
1 306 ::1/128 On-link
14 1005 2002::/16 On-link
14 261 2002:600b:fb95::600b:fb95/128
On-link
15 261 fe80::/64 On-link
10 261 fe80::/64 On-link
21 261 fe80::/64 On-link
10 261 fe80::64ae:bae7:3dc0:c8c4/128
On-link
21 261 fe80::e9f7:e24:3147:bd/128
On-link
15 261 fe80::f116:2dfd:1771:125a/128
On-link
1 306 ff00::/8 On-link
15 261 ff00::/8 On-link
10 261 ff00::/8 On-link
21 261 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
And here is the updated running config in case you need it:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
access-list outside_specific_blocks extended deny ip host 121.168.66.35 any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
ip local pool VPN_Split_Pool 192.168.3.70-192.168.3.80 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh 96.11.251.186 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Split_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Split_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Split_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:9e8466cd318c0bd35bc660fa65ba7a03
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Thanks again for your help,
Matthew -
Remote Access VPN (ipsec) can ping LAN interface of firewall but not clients on the company network.
The VPN will connect.
I can ping and connect to the ASA 5510 on it's LAN interface.
My problem is that I cannot ping or access anything on the LAN past the firewall. What am I doing wrong?
Here is my config.
Result of the command: "show config"
: Saved
: Written by enable_15 at 22:55:02.299 UTC Tue Jan 10 2012
ASA Version 8.2(5)
hostname ********
enable password UbBnTPKwu27ohfYB encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.x x.x.x.x
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.0.4.1 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network BC
network-object 10.0.3.0 255.255.255.0
network-object 10.0.4.0 255.255.255.0
access-list outside_access_in extended permit tcp any any eq ssh
access-list outside_access_in extended permit tcp any any eq 50000
access-list outside_access_in extended permit tcp any any eq 3390
access-list outside_access_in extended permit tcp any any eq 8066
access-list outside_access_in extended permit tcp any any eq 22225
access-list outside_access_in extended permit tcp any any eq 1600
access-list outside_access_in extended permit tcp any any eq 37260
access-list outside_access_in extended permit tcp any any eq 37261
access-list outside_access_in extended permit tcp any any eq 37262
access-list outside_access_in extended permit tcp any any eq 37263
access-list outside_access_in extended permit tcp any any eq 37264
access-list outside_access_in extended permit tcp any any eq 1435
access-list outside_access_in extended permit tcp any any eq 250
access-list outside_access_in extended permit tcp any any eq citrix-ica
access-list outside_access_in extended permit tcp any any eq 8080
access-list outside_access_in extended permit tcp any any eq www
access-list outside_access_in extended permit tcp any any eq 85
access-list outside_access_in extended permit tcp any any eq 8069
access-list outside_access_in extended permit tcp any any eq 3389
access-list outside_access_in extended permit tcp any any eq 23032
access-list outside_access_in extended permit tcp any any eq 32023
access-list outside_access_in extended permit tcp any any eq 3399
access-list outside_access_in extended permit udp any any eq 250
access-list outside_access_in extended permit udp any any eq 5008
access-list outside_access_in extended permit icmp any any
access-list splittunn-ppso extended permit ip 10.0.4.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list splittunn-ppso extended permit ip 10.0.3.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list nonat extended permit ip 10.0.4.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list nonat extended permit ip 10.0.3.0 255.255.255.0 10.10.10.0 255.255.255.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool vpn-pool 10.10.10.1-10.10.10.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
no asdm history enable
arp timeout 14400
nat-control
global (outside) 101 interface
nat (inside) 0 access-list nonat
nat (inside) 101 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 50000 10.0.4.58 50000 netmask 255.255.255.255
static (inside,outside) tcp interface ssh 10.0.4.7 ssh netmask 255.255.255.255
static (inside,outside) tcp interface 3390 10.0.3.249 3390 netmask 255.255.255.255
static (inside,outside) tcp interface 8066 10.0.3.249 8066 netmask 255.255.255.255
static (inside,outside) tcp interface 22225 10.0.4.58 22225 netmask 255.255.255.255
static (inside,outside) tcp interface 1600 10.0.4.58 1600 netmask 255.255.255.255
static (inside,outside) tcp interface 37260 10.0.4.58 37260 netmask 255.255.255.255
static (inside,outside) tcp interface 37261 10.0.4.58 37261 netmask 255.255.255.255
static (inside,outside) tcp interface 37262 10.0.4.58 37262 netmask 255.255.255.255
static (inside,outside) tcp interface 37263 10.0.4.58 37263 netmask 255.255.255.255
static (inside,outside) tcp interface 37264 10.0.4.58 37264 netmask 255.255.255.255
static (inside,outside) tcp interface 1433 10.0.4.240 1433 netmask 255.255.255.255
static (inside,outside) udp interface 5008 10.0.4.240 5008 netmask 255.255.255.255
static (inside,outside) udp interface 249 10.0.4.240 249 netmask 255.255.255.255
static (inside,outside) tcp interface 250 10.0.4.240 250 netmask 255.255.255.255
static (inside,outside) tcp interface www 10.0.4.15 www netmask 255.255.255.255
static (inside,outside) tcp interface citrix-ica 10.0.4.15 citrix-ica netmask 255.255.255.255
static (inside,outside) tcp interface 8080 10.0.4.15 8080 netmask 255.255.255.255
static (inside,outside) tcp interface 85 10.0.4.15 85 netmask 255.255.255.255
static (inside,outside) tcp interface 8069 10.0.4.236 8069 netmask 255.255.255.255
static (inside,outside) tcp interface 3399 10.0.4.236 3389 netmask 255.255.255.255
static (inside,outside) tcp interface 23032 10.0.4.244 23032 netmask 255.255.255.255
static (inside,outside) tcp interface 32023 10.0.4.244 32023 netmask 255.255.255.255
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
route inside 10.0.3.0 255.255.255.0 10.0.4.205 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 management
http x.x.x.x x.x.x.x outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
308205ec 308204d4 a0030201 0202106e cc7aa5a7 032009b8 cebcf4e9 52d49130
0d06092a 864886f7 0d010105 05003081 ca310b30 09060355 04061302 55533117
30150603 55040a13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
13165665 72695369 676e2054 72757374 204e6574 776f726b 313a3038 06035504
0b133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
20617574 686f7269 7a656420 75736520 6f6e6c79 31453043 06035504 03133c56
65726953 69676e20 436c6173 73203320 5075626c 69632050 72696d61 72792043
65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
30303230 38303030 3030305a 170d3230 30323037 32333539 35395a30 81b5310b
30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
496e632e 311f301d 06035504 0b131656 65726953 69676e20 54727573 74204e65
74776f72 6b313b30 39060355 040b1332 5465726d 73206f66 20757365 20617420
68747470 733a2f2f 7777772e 76657269 7369676e 2e636f6d 2f727061 20286329
3130312f 302d0603 55040313 26566572 69536967 6e20436c 61737320 33205365
63757265 20536572 76657220 4341202d 20473330 82012230 0d06092a 864886f7
0d010101 05000382 010f0030 82010a02 82010100 b187841f c20c45f5 bcab2597
a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
9c688b2e 957b899b 13cae234 34c1f35b f3497b62 83488174 d188786c 0253f9bc
7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
63cd1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8
18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 02030100 01a38201 df308201
db303406 082b0601 05050701 01042830 26302406 082b0601 05050730 01861868
7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1d130101
ff040830 060101ff 02010030 70060355 1d200469 30673065 060b6086 480186f8
45010717 03305630 2806082b 06010505 07020116 1c687474 70733a2f 2f777777
2e766572 69736967 6e2e636f 6d2f6370 73302a06 082b0601 05050702 02301e1a
1c687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
03551d1f 042d302b 3029a027 a0258623 68747470 3a2f2f63 726c2e76 65726973
69676e2e 636f6d2f 70636133 2d67352e 63726c30 0e060355 1d0f0101 ff040403
02010630 6d06082b 06010505 07010c04 61305fa1 5da05b30 59305730 55160969
6d616765 2f676966 3021301f 30070605 2b0e0302 1a04148f e5d31a86 ac8d8e6b
c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
1b311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301d0603
551d0e04 1604140d 445c1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355
1d230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300d0609
2a864886 f70d0101 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80
4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
b2227055 d9203340 3307c265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
6decd018 7d494aca 99c71928 a2bed877 24f78526 866d8705 404167d1 273aeddc
481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
6c2527b9 deb78458 c61f381e a4c4cb66
quit
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet x.x.x.x 255.255.255.255 outside
telnet 0.0.0.0 0.0.0.0 inside
telnet 0.0.0.0 0.0.0.0 management
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 management
ssh timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.1.2-192.168.1.254 management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
group-policy ppso internal
group-policy ppso attributes
dns-server value 10.0.4.241 10.0.4.14
split-tunnel-policy tunnelspecified
split-tunnel-network-list value splittunn-ppso
default-domain value ppso.local
split-dns value ppso.local
address-pools value vpn-pool
tunnel-group VPN type remote-access
tunnel-group VPN general-attributes
address-pool vpn-pool
default-group-policy VPN
tunnel-group VPN ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:88a9b69fc3d718c3badfa99db2c7ce4fYeah, I figured out where my problem was.
My IP Local Pool range was the problem.
I was using 10.10.10.0 which conflicted with a point-to-point connection where the serial interfaces were numbered and using 10.10.10.1 and 10.10.10.2.
Traffic would leave the firewall, hit the intended host, go back through my core router, then off to the other network.
I changed my ip local pool to a different range (192.168.100.0) and my problem was solved. -
ASA IPsec Remote Access VPN | NAT Question
We have a situation where a company that needs remote VPN access to our network is having an IP conflict with our subnet. I know this is a common issue and can often be resolved on the client side by changing the metirc on the network interface, but I am looking for a better solution on our end so I do not have to suggest workarounds.
Part of the problem is likely that our subnet is "too big", but I'm not going to be changing that now.
We are using 10.0.0.0/24 and the remote is using 10.0.11.0/24 and 10.1.0.0./16
I played around with some NAT rules and feel that I am missing something I am looking for suggestions, please.
Thank you.Hi,
This depends on your ASA firewalls software version and partly on its current NAT configurations.
I presume the following
Interfaces "inside" and "outside"
VPN Pool network of 10.10.100.0/24 (or some 192/172 network)
Software 8.2 and below
access-list VPN-POLICYNAT remark Static Policy NAT for VPN Client
access-list VPN-POLICYNAT permit ip 10.0.0.0 255.255.255.0 10.10.100.0 255.255.255.0
static (inside,outside) 192.168.10.0 access-list VPN-POLICYNAT
Key things to keep in mind with this software level is that if any of our internal hosts on the network 10.0.0.0/24 also have a "static" configuration that binds their local IP address to a public IP address then you might have to insert the above configuration and then remove the original "static" command and enter it back again.
This will change the order or the "static" commands so that the original "static" command wont override this new configuration as they are processed in order they are inserted to the configuration. The remove/add part is just to change their order in the configuration
Software 8.3 and above
object network LAN
subnet 10.0.0.0 255.255.255.0
object network LAN-VPN
subnet 192.168.10.0 255.255.255.0
object-group network VPN-POOL
subnet 10.10.100.0 255.255.255.0
nat (inside,outside) 1 source static LAN LAN-VPN destination static VPN-POOL VPN-POOL
In the above configuration we do the same as in the older software versions configuration but we have the number "1" in the "nat" configuration which places it at the very top of your NAT configurations and therefore it applies. No need to remove any existing configuration and enter them again like in the old software
In addition to the above NAT configuration you naturally have to make sure that the traffic to the NATed LAN network goes to the VPN. So if using Split Tunnel the NAT network needs to be added to the VPN ACL. If using Full Tunnel then naturally everything should already be coming through the VPN. I imagine though that you are using Split Tunnel, or?
Hope this helps
Please do remember to mark a reply as the correct answer if it answered your question.
Feel free to ask more if needed
- Jouni -
Can you create a Remote Access VPN connection to tunnel DMZ LAN and Inside Networks simultaneously?
I have a customer that has a ASA 5510 version 8.3 with IPSEC Client Access that includes some of their networks on the Inside interface. The issue they are having is when their mobile users connect with the vpn client (which is using split tunneling), they can no longer access their web server applications that are running in the DMZ. Without the client connected, they access the web servers via the external public IP. Once they are connected via vpn, their default dns server becomes the internal AD DNS server, which resolves the DNS of the web servers to the private DMZ ip address.
Can a Remote Access VPN client connection be allowed to connect to both the DMZ interface and the Inside Interface? I had always only setup RA VPN clients to connect to networks on the Inside Interface.
I tried adding the DMZ network to the Split Tunnel list, but I could not access anything it while connected to vpn using the private IP addresses.Yes, you should be able to access DMZ subnets as well if they are added to the split tunnel ACL. You could check the NAT exemption configuration for the DMZ and also check if the ASA is forwarding the packet through DMZ interface by configuring captures on the DMZ interface.
Share the configuration if you want help with the NAT exemption part. -
Remote access VPN-unable to connect inside-URGENT
Hi,
I have configured Remote access VPN in cisco ASA 5520.Whenever I am trying to connect from outside it's connecting fine.It aslo getting IP from pool but prob is i am unable to connect/ping inside nw.
Pls help me...how to resolve this issue.I had the same problem on an IOS router (871). My solution was one of two things. I downloaded the most up-to-date version of the VPN client (5.0.02.90) as opposed to the version I had or it was a software firewall (Norton 360). I have two different computers. One works just fine...the other connects but no traffic passes through. Here is what I have:
Computer 1 (working)- VPN Client v5.0.02.0090 and Network Associates Enterprise VirusScan.
Computer 2 (not working) - VPN Client v5.0.00.0340 and Norton 360.
I highly doubt it is the VPN Client, but sometimes you never know. Check your software firewall and try disabling it. Let me know how this works. -
Problem with Remote Access VPN on ASA 5505
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
Begin connection process
3 15:09:21.287 12/11/12 Sev=Info/4 CM/0x63100004
Establish secure connection
4 15:09:21.287 12/11/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
5 15:09:21.287 12/11/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
6 15:09:21.287 12/11/12 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
7 15:09:21.303 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
8 15:09:21.365 12/11/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
9 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
10 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
11 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
12 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
13 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
14 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
15 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
16 15:09:21.334 12/11/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
17 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
18 15:09:21.334 12/11/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
19 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xFBCE, Remote Port = 0x1194
20 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
21 15:09:21.334 12/11/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 15:09:21.365 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 15:09:21.365 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 15:09:21.365 12/11/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 15:09:21.474 12/11/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
26 15:09:21.474 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
27 15:09:27.319 12/11/12 Sev=Info/4 CM/0x63100017
xAuth application returned
28 15:09:27.319 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
29 15:09:27.365 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
30 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
31 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
32 15:09:27.365 12/11/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
33 15:09:27.365 12/11/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
34 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
35 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
36 15:09:27.397 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
37 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
38 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
39 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
40 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
41 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
42 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO
43 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
44 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.2(5) built by builders on Fri 20-May-11 16:00
45 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
46 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
47 15:09:27.397 12/11/12 Sev=Info/4 CM/0x63100019
Mode Config data received
48 15:09:27.412 12/11/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
49 15:09:27.412 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
50 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
51 15:09:27.444 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
52 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
53 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 6 seconds, setting expiry to 86394 seconds from now
54 15:09:27.459 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
55 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:NO_PROPOSAL_CHOSEN) from **.**.***.***
56 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DEL) to **.**.***.***
57 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000049
Discarding IPsec SA negotiation, MsgID=CE99A8A8
58 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
59 15:09:27.459 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
60 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000058
Received an ISAKMP message for a non-active SA, I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924
61 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(Dropped) from **.**.***.***
62 15:09:27.490 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
63 15:09:30.475 12/11/12 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
64 15:09:30.475 12/11/12 Sev=Info/4 CM/0x63100012
Phase 1 SA deleted before first Phase 2 SA is up cause by "DEL_REASON_IKE_NEG_FAILED". 0 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
65 15:09:30.475 12/11/12 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
66 15:09:30.475 12/11/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
67 15:09:30.475 12/11/12 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
68 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
69 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
70 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
71 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
The running configuration is as follows (there is a site-to-site VPN set up as well to another ASA 5505, but that is working flawlessly):
: Saved
ASA Version 8.2(5)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
boot system disk0:/asa825-k8.bin
ftp mode passive
access-list outside_nat0_outbound extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit NCHCO 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (outside) 0 access-list outside_nat0_outbound
route outside 0.0.0.0 0.0.0.0 74.219.208.49 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec transform-set l2tp-transform mode transport
crypto ipsec transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_3DES_MD5
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp ipsec-over-tcp port 10000
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHVPN internal
group-policy NCHVPN attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value NCHCO
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password QhZZtJfwbnowceB7 encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
pre-shared-key *****
tunnel-group NCHVPN type remote-access
tunnel-group NCHVPN general-attributes
address-pool VPN_Pool
default-group-policy NCHVPN
tunnel-group NCHVPN ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:15852745977ff159ba808c4a4feb61fa
: end
asdm image disk0:/asdm-645.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Anyone have any idea why this is happening?
Thanks!Thanks again for your reply, and sorry about the late response, havent gotten back to this issue until just now. I applied the above command as you specified, and unfortunately, it did not resolve the problem. Below are the logs from the VPN Client for the connection + attempted browsing of a network share that is behind the ASA, and the new running configuration.
VPN Client Log:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
331 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100002
Begin connection process
332 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100004
Establish secure connection
333 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "69.61.228.178"
334 13:11:41.362 12/17/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 69.61.228.178.
335 13:11:41.362 12/17/12 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
336 13:11:41.424 12/17/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
337 13:11:41.362 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 69.61.228.178
338 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
339 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from 69.61.228.178
340 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
341 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
342 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
343 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
344 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
345 13:11:41.393 12/17/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
346 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 69.61.228.178
347 13:11:41.393 12/17/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
348 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xD271, Remote Port = 0x1194
349 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
350 13:11:41.393 12/17/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
351 13:11:41.424 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
352 13:11:41.424 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
353 13:11:41.424 12/17/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
354 13:11:41.424 12/17/12 Sev=Info/4 CM/0x63100017
xAuth application returned
355 13:11:41.424 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
356 13:11:41.456 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
357 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
358 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
359 13:11:41.456 12/17/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
360 13:11:41.456 12/17/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
361 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
362 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
363 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
364 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
365 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
366 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
367 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
368 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
369 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
370 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
371 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
372 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
373 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
374 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
375 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
376 13:11:41.502 12/17/12 Sev=Info/4 CM/0x63100019
Mode Config data received
377 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = 69.61.228.178, Remote IP = 0.0.0.0
378 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 69.61.228.178
379 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
380 13:11:41.534 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from 69.61.228.178
381 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
382 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 0 seconds, setting expiry to 86400 seconds from now
383 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
384 13:11:41.549 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from 69.61.228.178
385 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
386 13:11:41.549 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to 69.61.228.178
387 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=C4F5B5A6 OUTBOUND SPI = 0xD2DBADEA INBOUND SPI = 0x14762837)
388 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xD2DBADEA
389 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x14762837
390 13:11:41.549 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
391 13:11:41.877 12/17/12 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
392 13:11:43.455 12/17/12 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
393 13:11:43.455 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 266
394 13:11:47.517 12/17/12 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
395 13:11:47.517 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
69.61.228.178 255.255.255.255 192.168.1.1 192.168.1.162 100
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.2 255.255.255.255 192.168.1.162 192.168.1.162 100
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 266
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 266
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 266
396 13:11:47.517 12/17/12 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
397 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310001A
One secure connection established
398 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.1.162. Current hostname: MATT-PC, Current address(es): 192.168.2.70, 192.168.1.162.
399 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: MATT-PC, Current address(es): 192.168.2.70, 192.168.1.162.
400 13:11:47.517 12/17/12 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
401 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
402 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
403 13:11:47.517 12/17/12 Sev=Info/6 IPSEC/0x6370002C
Sent 109 packets, 0 were fragmented.
404 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
405 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
406 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xeaaddbd2 into key list
407 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
408 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x37287614 into key list
409 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
410 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 192.168.1.162. SG: 69.61.228.178
411 13:11:47.517 12/17/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
412 13:11:52.688 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
413 13:11:52.688 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476009
414 13:11:52.704 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
415 13:11:52.704 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
416 13:11:52.704 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476009, seq# expected = 2722476009
417 13:12:03.187 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
418 13:12:03.187 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476010
419 13:12:03.202 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
420 13:12:03.202 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
421 13:12:03.202 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476010, seq# expected = 2722476010
422 13:12:14.185 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
423 13:12:14.185 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476011
424 13:12:14.201 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
425 13:12:14.201 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
426 13:12:14.201 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476011, seq# expected = 2722476011
427 13:12:24.762 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
428 13:12:24.762 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476012
429 13:12:24.778 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
430 13:12:24.778 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
431 13:12:24.778 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476012, seq# expected = 2722476012
New running configuration:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:b6ce58676b6aaeba48caacbeefea53a5
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
I'm at a loss myself as to why this isn't working, and i'm sure that you are running out of solutions yourself. Any other ideas? I really need to get this working.
Thanks so much!
Matthew
Maybe you are looking for
-
Was unable to load data class info from sync services. try again later.
Since installing the latest version of itunes (11.1.5.5) whenever I have either mine or my wife's iphones (4 and 5c, both with the latest 7.1.1) turned on and I start iTunes, I receive the error message saying that itunes was unable to load data clas
-
Word 2013 - MSI Install vs. One-Click Install - COM Exception Error
Hello - we have a 3rd party control that sits on top of word to render word documents. In a MSI installation of Word 2013 everything works fine. When we use the one-click installation the rendering does not work and the system throws a com exceptio
-
Restrict PO based on the maximum stock level qty in MMR
Hi We have maintained Maximum Stock level in MRP1 in Material Master. Is there any facility which can restrict the Purchaser, not to raise any PO more than maximum stock level qty which is maintained in Material Master ??? how to do ? Is there any us
-
DVD drive replacement on Satellite A100-646
Hi all, I want replace the DVD drive on my laptop. (I have many problems never solved) Do you know if exist a list of compatibility model for the A100-646? Model to suggest me? Thanks a lot. Regards Fabrizio
-
How to execute a Unix Command in java
Hi, Iam trying to execute a unix command on Sun Solaris by passing that command to a java program. How can I achieve this? Thanks in advance.