Want to create vlan on asa5510 (8.2)

User want to create on 5 network , 100.x , 200.x , 210.x , 250.x , 220.x .at the ASA5510, no enough port for 5 network.
So I want to create 4 vlans on eth 0/3. I can create vlan but i cannot run this command "
switchport mode trunk" "
"switchport trunk allowed vlan list" how can be done for that?Thanks
Acctually i want to use like this
ASA5510-----4 vlans on eth 0/3------switch----vlan200,vlan210,vlan250,vlan220.
Ko Htwe

You don't have to configure "switchport mode trunk" on the ASA interface.
You just have to configure the sub interfaces under eth0/3 and configure vlan under that interface.
Eg:
interface eth0/3.200
   vlan 200
   ip address 200.200.200.1 255.255.255.0
   nameif vlan200-dmz
   security-level 50
interface eth0/3.210
   vlan 210
   ip address 210.210.210.1 255.255.255.0
   nameif vlan210-dmz
   security-level 55
Hope that helps.

Similar Messages

Creating VLAN

How is VLANs configured on a switch ? What are the parameters defined while creating a VLAN/ Voice VLAN ? Since switch operates on layer 2 switch, is it required to define vlans on router as well. This might be very simple and basics of networking. Need to understand to clarify my doubts.
Thanks
Feroz
Sent from Cisco Technical Support iPhone App

HI Feroz,
VLAN is a virtual LAN. In technical terms, a VLAN is a broadcast domain created by switches. Normally, it is a router creating that broadcast domain. With VLAN’s, a switch can create the broadcast domain.
This works by, you, the administrator, putting some switch ports in a VLAN other than 1, the default VLAN. All ports in a single VLAN are in a single broadcast domain.
Because switches can talk to each other, some ports on switch A can be in VLAN 10 and other ports on switch B can be in VLAN 10. Broadcasts between these devices will not be seen on any other port in any other VLAN, other than 10. However, these devices can all communicate because they are on the same VLAN. Without additional configuration, they would not be able to communicate with any other devices, not in their VLAN.
Please find the details below:
Vlan on Switches:-
Two types of Vlan(Layer 2 - Layer3)
Layer 2 vlan:
config t# vlan
Eg:
Let’s say we wanted to create VLAN’s 5 and 10. We want to put ports 2 in VLAN 5 (Marketing) and port 3 in VLAN 10 (Human Resources). On a Cisco 2950 switch, here is how you would do it:
# vlan 5
#name marketing
vlan 10
name humanresouces
exit
int f0/2
switchport mode access
switchport access vlan 5
int f0/3
switchport mode access
switchport access vlan 10
Layer 3:
conf t# interface vlan 2
followed by ip address.
Please find below link which explains complete info on VLans.
http://www.cisco.com/en/US/docs/switches/lan/catalyst2950/software/release/12.1_9_ea1/configuration/guide/swvlan.html
2- Vlan on Router:
A vlan configuration on a router is slightly different than on a switch. On a switch, you would create the vlan and then the routed vlan interface.
On a router you tie a vlan to a subinterface. You need to create the subinterface and then do the encapsulation dot1q command. This command basically assigned the vlan to the subinterface. In this example, there are 2 vlans, vlan 100 and 201. On the eth 0/0 interface, I created two subinterfaces. fastethernet0/0.100 and f0/0.201. Notice that I matched the subinterface number with the vlan ID. You do not have to do this, but it is a best practice and really helps you as the administrator keep things organized. So, under f0/0.100, there is the encapsulation dot1q 100, which basically binds vlan 100 to subinterface f0/0.100, then I assigned the IP. The same is for the other subinterface. So the router is trunking two vlans on its f0/0 interface, vlan's 100 and 201.
interface FastEthernet0/0
no ip address
speed 100
full-duplex
interface FastEthernet0/0.100
description test Network
encapsulation dot1Q 100
ip address 192.168.102.1 255.255.255.128
no snmp trap link-status
interface FastEthernet0/0.201
description Office
encapsulation dot1Q 201
ip address 205.127.102.129 255.255.255.128
no snmp trap link-status
Kindly go through the same and reply back if you need any clarification on the same.
HTH
Regards
Inayath
*Plz rate the usefull posts.

Can create vlan group on eth0 after OVM Server installation?

Hi,
I have installed OVM server to use eth0 without vlan segment for ovm manager to manage OVM server.
Now if I want to use eth0 for virtual machine management purpose as well, can I edit this network, create vlan group on eth0,
one for server managent + cluster heartbeat + live migration
one for virtual machine management?
Or I have to reinstall OVM server with vlan segment on eth0?
Appreciate any comment on this.

it was the wrong mfc42.dll version

Help create VLAN for home use.

I use Cisco switch SG300 and SG200 series. I set my home network as attach picture.
I want set up VLAN with these condition
1.Every port can connect to internet through ADSL router.
2.VLAN10( Home alarm and IP camera ) can access by internat, connect by access point and PC file server
3.Every port can connect the PC file server
I am new for network and fail to try setup myself and not understand static route.
Thank you.
Jarey
[email protected]

Hi Jarey,
Are you sure you want to do this on the switch as opposed to the router? Are you going to use static IP addresses for the vlans or do you want your router to issue DHCP?
To proceed, using the switch for inter-vlan routing, make sure the SG300 is in layer 3 mode.
1. If you are currently in layer 2 mode, open a CLI connection and issue command:
set system mode router
Take note that this will delete your current config and the switch will reboot.
2. Create the vlans on your switch under VLAN Management -> create vlan
3. Go to IP Configuration -> ipv4 interface and assign each vlan a static IP for the switch in the subnet for the new vlan
4. Vlan Management -> Interface settings. I would leave all the ports as trunk ports, or change the ports to trunk if you have previously changed them.
5. Vlan Management -> Port VLAN membership. Assign your vlans to the appropriate ports.
6. When everything is all plugged in, you should be able to see the switch created static routes for you already under IP Configuration -> IPV4 static routes. Make sure all your subnets are there and are showing route type local
7. You may need to add a route such as 0.0.0.0 with the next hop being your router
At this point, you should be up and running, with all vlans connected to each other and to the internet.
If you want to restrict access across the vlans, you'll have to create access control lists.
You need to first create an ACL (Access control -> IPV4 based ACL) and give it a name. then go over to IPV4 based ACE where you put the actual access control rules.
This is a sample set of rules I made, it will block all access between two subnets (each vlan you created above will have to be its own subnet) and allow certain traffic such as 3389 - remote desktop, etc. You'll need to customize based upon your needs and subnet IPs. So for ex, to allow the Xboxes to access the file server, rather than any - any, you put the xbox subnet or specific IPs as the source, the file server as the destination, and the ports used as source ports. Remember to make the converse of the rule as well.
Then, go to Access Control -> ACL bindings and bind the access control list to the applicable ports.
Hope that helps, good luck with your set up.
Best,
David
Please remember to rate helpful posts and identify correct answers.

Create vlan on SRW2024

Hi guys,
I need help the proper way to create vlan on SRW2024....
i have 3 segments vlan 10,20 and 30...how to create and make sure this 3 vlan can ping each other, the proper steps, i've tried to follow the manual but have problem to understand the term using in linksys.
thank you guys

You won't be able to "ping" the vlan's from the same switch. Also, you can only setup one vlan from which the switch can be managed. This is defined under the SETUP->NETWORK SETTINGS section. Look for "Management VLAN." You'll only be able to ping the switch from ports assigned to that VLAN.
I'm betting you have no problems creating VLANs. What can be unclear is how to assign ports.
To add a port to a VLAN...
1-identify port
2-go into "VLAN Management" and then "Ports to VLAN"
3-go into the VLAN you want the port to be in (from the SELECT VLAN drop down)
4-set switch port mode to "Access" (if not already)
5-set membership to "UnTagged"
6-ensure the trunk is tagged in this VLAN
7-save
To MOVE a port to a different VLAN...
1-identify port
2-go into "VLAN Management" and then "Ports to VLAN"
3-go into the VLAN you want the port to be in (from the SELECT VLAN drop down)
4-set membership to "UnTagged"
5-save
As I've said before on this forum, I've found it is sometimes more straight forward with the srw2024 to setup a TFTP server on your PC...backup the config...edit the config...upload new config...reboot switch.

UC320W create vlan on srw2024P

Any documentation for creating the vlan for voice on the srw2024 and the required settings? Thnaks

You won't be able to "ping" the vlan's from the same switch. Also, you can only setup one vlan from which the switch can be managed. This is defined under the SETUP->NETWORK SETTINGS section. Look for "Management VLAN." You'll only be able to ping the switch from ports assigned to that VLAN.
I'm betting you have no problems creating VLANs. What can be unclear is how to assign ports.
To add a port to a VLAN...
1-identify port
2-go into "VLAN Management" and then "Ports to VLAN"
3-go into the VLAN you want the port to be in (from the SELECT VLAN drop down)
4-set switch port mode to "Access" (if not already)
5-set membership to "UnTagged"
6-ensure the trunk is tagged in this VLAN
7-save
To MOVE a port to a different VLAN...
1-identify port
2-go into "VLAN Management" and then "Ports to VLAN"
3-go into the VLAN you want the port to be in (from the SELECT VLAN drop down)
4-set membership to "UnTagged"
5-save
As I've said before on this forum, I've found it is sometimes more straight forward with the srw2024 to setup a TFTP server on your PC...backup the config...edit the config...upload new config...reboot switch.

Creating VLAN on our Cisco 300 series router

I am wanting to create separate VLANs on our Cisco 300 series switches, but I am struggling to find any decent examples out there.
Our basic infrastructure is
Router with
192.168.1.1 VLAN1
192.168.2.1 VLAN2
The switch is set up on ports 2345 for VLAN2
Port 1 is attached to the router on VLAN1 and VLAN2 assigned.
My problems seem to be that I really not sure what settings I should be using for each the ports to get this to work correctly

Hi,
Hope below link will have the information which you are looking for.
https://supportforums.cisco.com/document/140341/vlan-configuration-articles-sx200300-series-managed-switches
If you are looking for only vlan creation then below link will help.
http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=80
According to your above description you have connected the router to port 1 of switch and you have configured it as vlan 1...Should this port be trunk???
Regards
Najaf

When one or more family members who have been sharing one iTunes account wants to create their own iTunes account can they each upload the music/apps from the shared iTunes on their devices to the new iTunes account?

When one or more family members who have been sharing one iTunes account wants to create their own iTunes account can they each upload the music/apps from the shared iTunes on their devices to the new iTunes account?

Yes. I would clarify your statement about the "shared" iTunes Library though. If you want each iOS device to have its own music library, you should create separate user accounts for them. Read:
iTunes: How to share music between different accounts on a single computer
How to use multiple iPods, iPads, or iPhones with one computer

My friend wanted to create a new iCloud account that was different to her iTunes and app one when she deleted her iCloud account that was the same as her iTunes it won't let her log into her iTunes one now

My friend wanted to create a new iCloud account that was different to her iTunes and app one when she deleted her iCloud account that was the same as her iTunes it won't let her log into her iTunes one now what can I do to fix it she has paid or apps and songs and of she makes another account everything will be lost.
Need help please :) thanks

Ah thanks Razmee however there is NO option to delete the iCloud account in settings!

How do I create a new account for an iPod that is on an existing account? My brother and I have shared an account for five years, and now that I'm moving out, I want to create my own account but still want to be able to play the music I've purchased.

My brother and I have shared an account for five years, and now that I'm moving out, I want to create my own separate account but still want to be able to play the music I've purchased over five years.

In order to continue to play and sync the music you purchased with your old account, you'll need to authorize your new computer/iTunes library to do so. You can do this by choosing Store -> Authorize This Computer and then entering in your old account credentials.
That's all you should need to. Then just create your own account and start purchasing and using it the same you have with the old one.
B-rock

Hopefully someone can help.... I have an Iphone 5 and want to create a music video playlist on my phone so then i can play through my apple tv... but when i make a playlist in itunes and try to add it over to my iphone it wont let me sync the playlist...?

Hopefully someone can help.... I have an Iphone 5 and want to create a music video playlist on my phone so then i can play through my apple tv... but when i make a playlist in itunes and try to add it over to my iphone it wont let me sync the playlist...? I have already added the music videos to my iphone so that is not the problem.... i cant seem to figure out how to make a playlist for them... IE: to make the videos play consecutively in the order i want without stopping after each video and gong back to the list.... this is what i have had to resort to make it work....what i want to do....is be able to make a playlist of videos on my iphone 5....take my apple tv to friends houses and with wifi....set up apple tv and play videos at the party and not have to stand by with the remote and find a new video to play stopping the music between the songs/videos....very annoying....and have spent over 4 hours one day and an hour and a half today on the phone today with a sr. advisor with apple and they have no clue.... this seems sooooo simple.... please somebody that really knows how to do this....i will be indebted forever...............
Mike

Thank you for replying. Yes I deleted the old email address..

I cannot sign in. "This Apple ID has not yet been used with the iTunes Store. Please review your account information." I click "Review", next message "You must turn on cookies to continue.   Cookies must be enabled if you want to create or edit.. etc."

I applied and received an upgrade code to Redeem Mountain Lion for my new MBP.
I get this message when I try to Sign in to the App Store after entering the redemption content code, and also if I just try to "Sign In".   The first part of the error is true - I haven't used the AppleID with the iTunes store.
I received the upgrade code using this same AppleID, so I don't think I can use a different AppleID.
I also tried to re-create this appleID...(it was one suggestion I saw for this issue) It doesn't let me since the ID already exists...
The error is:
"This Apple ID has not yet been used with the iTunes Store. Please review your account information." I click "Review", next message "You must turn on cookies to continue.   Cookies must be enabled if you want to create or edit.. etc."
It's clearly not a cookie issue..   Stuck...

The first part of the error is true - I haven't used the AppleID with the iTunes store.
Try here > Using an existing Apple ID with the iTunes Store and Mac App Store
received the upgrade code using this same AppleID, so I don't think I can use a different AppleID.
Correct.
It's clearly not a cookie issue..
As for cookies. Quit the App Store. Now open the Finder. From the Finder menu bar click Go > Go to Folder.
Type this exactly as you see it here:   ~/Library/Cookies
Click Go the move the   com.apple.appstore.plist   file from the Cookies folder to the Trash.
Relaunch the App Store.

When i want to create a face time it tells me to vertify my email address. When i go to do this i have to type in my apple ID and password on the Apple website, however when ever i do this i get a message saying Invalid account for this Email Address..

when i want to create a face time it tells me to vertify my email address. When i go to do this i have to type in my apple ID and password on the Apple website, however when ever i do this i get a message saying Invalid account for this Email Address..

Same problem here. Whats the deal?! Apple??

I want to create a Ajax based Chating application using java .

hi . I want to create an chating Application , and ajax based chatting application using java as my server side language ..i have some idea about it .. but one thing that i m not understanding is that how i will communicate with other users because each user has its own session so what i will do to send one messge to all the users ???? . i m new to JavaEE and i have chosen this as my semester project .. i need some help regarding this .

First get it working without AJAX.

I want to create a different plug-in . Could you please send me an email adress to contact about my questions for plug-ins?

Dear Sir / Madam,
First of all my english is not good enough and apologise for that. I want to create a kinda different java plug-in on mozilla . I ve been playin a textbase game for many years. However it takes many hours to play it manually. I d like to create a script for that and think script will work by itself (it will read 3d codes paste them automatically, it will click some words in website automatically etc.) I saw that one on your system its called "omerta rankscript". Could you tell me how i can start to do this and ? is it easy or how long time it takes to create a new plugin like this? also may i see the codes of this plug-in(omerta rankscript)?
Thank you for your consideration.
Best Regards,
Zafer ATABAY

Depending on what you want to develop, you could consider an ''extension'' or a ''userscript''. A plugin probably is not the right type of add-on to create.
For suggestions and assistance with these different kinds of add-ons:
Extensions:
* http://forums.addons.mozilla.org/
* http://forums.mozillazine.org/viewforum.php?f=19
Userscripts:
* http://userscripts.org/forums
Good luck with your project.

Want to create vlan on asa5510 (8.2)

Similar Messages

Maybe you are looking for