WCCP and WAN optimisation via Layer 3 connection
Hi There,
I need some help with WCCP, however with Riverbeds instead of WAAS.
The topology of the set up is as follows:
WAN - R1 - LAN - L3 Switch - Riverbed
The clients reside on the WAN side and the servers reside on the LAN side.
My business wishes to enable WCCP on two separate WAN routers to the single Riverbed. One router is fuly managed service, and the other rout the is managed by the business IT team.
All the articles that I have come across talk about enabling WCCP on the router whereby the WAN optimisation appliance is directly connected to a interface router. I need to configure WCCP to a Riverbed that is connected to a subnet that is a single hop away via a Layer 3 switch.
My plan is to enable WCCP in the inbound directions on both the LAN and WAN interfaces, however my concern is that this design will mean the traffic passing through the LAN side interface will be optimised twice.
Can any one confirm if this would happen? If it could happen can it potentially be stopped by placing a "ip wccp redirect exclude out" command on the LAN interface.
Thanks is advance for your help.
Hi Andreas,
"ip wccp redirect exclude out" only makes sense if you have a "ip wccp redirect out"
on a L3 interface on the router.
It's purpose is to avoid redirecting an already optimised packet, comming from a L3-interface where the WAAS/Riverbed device is connected, once more.
A double redirect will, in a WAAS setup, cause the WAAS device to drop the packet, because
it suspects a routing loop... don't know what Riverbed does.
Running only with "ip wccp redirect in" on both the WAN and LAN interface will cause :
1) a packet comming in from the LAN, is supposed to be unoptimised, and will be redirected
2) a packet comming in from the WAN, is supposed to be optimised, and will also redirected
3) an IP-interface with only the WAAS/Riverbed connected should NEVER be redirected !
If you cannot isolate your WAAr/Riverbed in it's own L3 subnet (subinterface/VLAN),
and therefore have to place it in the "ordinary" LAN subnet, packets from the WAAS/Riverbed will becomes candidates for redirection (even with "ip wccp redirect in"), you'll need to use "WCCP negotiated Return", but don't know whether Riverbed supports this,
Riverbed normally uses "tunnels" on the WAN side, and this makes the WCCP setup somewhat different.
You should really consult the Riverbed documentation or their support
... or migrate to Cisco WAAS ;-)
Best regards
Finn Poulsen
Similar Messages
-
Submit Referrer and User Agent via URL(Connection)?
Hi,
I retrieve some data via http using a URL (and a URLConnection) class. When I check the logfiles, the user agent information submitted by this connection is the name of the JRE-version.
So my question is: how can I submit custom user agent (and referrer) information? Possibly using the output-methods of a URLConnection?
kind regards
Oxyurlconn.setRequestProperty("referer","www.domain.com");
urlconn.setRequestProperty("user-agent","Mozilla/4.0 (compatible; MSIE 5.01; Windows NT 5.0"); -
I need help resetting my phone!
Depends, if you've synced with this iTunes, while that passcode was enabled, you won't be prompted to enter the passcode when connecting your phone. If you have not synced, while that passcode was enabled, you will. So, if you fall in the later, there is no way to do what you want.
-
Apple iTouch and Sony PSP will not connect to Home...
Please, please can someone help.....
Just received my kit for the Home Hub 2.0, (although as my PC is close by this is connected via ethernet cable), other than this, this is the first time I have gone wireless, main reason is that I am getting a slightly better deal and that I wanted to be able to connect all of my gaming and phone devices via wireless connection.
Connected up, installed the software, first up was the iTouch:
1. Turned on Wi-Fi, straight away my SSID was showing, selected it, it then asked for my Password/Security Key.
2. I entered the correct key, then tried to connect, all I get is 'Unable to join the network'.
Next the PSP:
1. Created a New Connection to get online, scanned automatically and again straight away my Home Hub was found.
2. Went through all the setup screens and entered the key when prompted, when I then tried to connect the following message was displayed, 'The access point was not detected'.
I have tried setting the key from WPA-WPA2 to just WPA, even tried WEP, still the same, I have checked all password and keys that I am typing in correctly.... I have been on this for 3 hours now and am at a loss, this should be so simple why is ist not???.... any thoughts would be very much appreciated.
Many thanks
Solved!
Go to Solution.Hi yasjooni and welcome
I've never connected either devices (don't own either)
but
regarding the itouch, try changing the wireless channel (I'll guess the hub may be on ch1)
regarding the PSP, have a read of this (also note there is a help video for connecting via wpa) - http://bt.custhelp.com/app/answers/detail/a_id/11266/kw/psp/c/346,1276,1035
-+-No longer a forum member-+- -
My early 2009 Mac Pro does not connect via bluetooth to my sound bar or bluetooth mini speakers. Both my wireless keyboard and mouse have no problems connecting. What do I need to do to connect to external bluetooth devices?
I would always have a wired keyboard and mouse on hand (need not be expensive ... any cheap wired devices will work). "Emergency recovery" procedures can activate features in random order, so the opportunity to select a recovery partition may pass before the wireless devices are recognized.
That will let you select the "turn on Bluetooth" icon. -
I have an Iphone 4s and i can't make a connection to my mac and other devices via bluetooth! Why is this a problem and how can i repair it?
"I have an Iphone 4s and i can't make a connection to my mac and other devices via bluetooth! ":
That is correct.
"Why is this a problem and how can i repair it?"
Becasue this has never been a feature of iphone/ipod/ipad. There is nothing to repair. -
I want to add apple tv via hdmi connection , and I already have ethernet input of tv for my viera cast connection, which gets Amazon prime. Wireless connection is APE base and APX, Want to add
apple tv to get Netflix so I can cancel my xfinity premium channels. Will this set up work. p.s as you can tell I am a Mac novice.Providing you have a free HDMI port on the TV and the location you would put the Apple TV will allow it to connect to your network, you should be good to go.
-
When trying to update ITunes on my pc using Iphone 4 verizon personal hotspot via usb connection the download fails.
I called this problem into Apple and they solved it for me. The problem is in the downloader associated with iTunes. Skip that step and go to Apple.com and download the new iTunes softwere update (Version 11.1) directly. I did this and installed it successfully. After restarting the computer iTunes recognized my phone and all was well. Then I updated and installed the ios7 update without any problems. No charge. Full cudo's to Apple!
-
I have a 27" thunderbolt display NOT the iMac, and I'm trying to connect my xbox 360 to it via the Belkin AV360. I plug everything in and it does not work? I check all the power cables and and connections and still not he issue. Iv'e tried C-F2 also. has anyone used this devive (AV360) on there own 27" thunderbolt display (not the imac) and gotten it to work? If so I'd appreciate the help.
There are multiple reasons that lead to issue. You should read the troubleshooting guide to get the right solution to solve the issue: iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support
-
Hi I have two macbook pro, i connected one from another via lan cable , now when i removed it, its showing me some pop up again and again saying server may not exists and there was a problem connecting to ishan's macbook pro
If you just reboot it, does the problem go away?
-
I have a 27" iMac connected to several others pc and to Server via router. Very frequently Lan or internet drops in my iMac. I Have OS 10.6.7 with all updates.
Issues like this are going to be related to the network. Intermittant problems are typically due to network interference, have you checked istumbler.net to get a report of your network?
-
My ipad 2 and iphone 4S won't connect to app store via wifi but will connect via 3g
my ipad 2 and iphone 4S won't connect to app store via wifi but will connect via 3g - both are running 6.0.1 - I have tired several wifi networks but same result.
Hi LandJ1980,
I would recommend first trying these steps:
iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting
http://support.apple.com/kb/HT1430
If that does not work, this article has some additional ideas to try, even though you are only seeing this with the App Store:
Can't connect to the iTunes Store
http://support.apple.com/kb/ts1368
Cheers!
- Ari -
I WAS USING I PHONE4 AND MY CAR KIT WAS WORKING PERFECT WITH IT VIA BLUETOOTH(RENAULT GRAND SCENIC 2011) BUT I BOUGHT THE NEW 4S AND EVENTHOUGH I CAN BE CONNECTED TO MY CAR KIT BY BLUETOOTH I CAN NOT HEAR IT ON MY CAR STREO.CAN ANYBODY HELP ME
Please stop posting in ALL UPPER CASE; it is considered SHOUTING, is harder to read, and is considered rude.
If you have not yet done so unpair the car kit from the phone, or better yet reset it completely, Forget the car kit in the iPhone, and pair it anew. -
I have an Apple Ipad. I was having problems receiving and sending emails via my yahoo email account. I deleted the account and then tried to install it but it won't connect to server. Could you let me know what I do please?
I think you have to turn off Private Browsing.
Tap "Private" on Safari Screen to disable Private Browsing. When top of screen is white, Private Browsing is off.
http://i1224.photobucket.com/albums/ee374/Diavonex/547958b4a8c01ac084dd6649e8386 a0f_zps12fa0cca.jpg -
my iPhone 3gs got stuck in "connect to iTunes" symble I click update or restore it via iTunes after the update it remains same and and give me symble to connect to iTunes plz help
Sorry, this forum do not support jailbroken iPhone, you have to find solutions from somewhere else.
Maybe you are looking for
-
My Apple ID has been disabled, it won't let me updated my previous purchases. No reason for why it has been disabled or how to enable it again. I reset my password, security questions and billing info. Nothing- I even called Apple SUpport 1-800 # and
-
Hard drive not appearing during restore from Time Machine?
While attempting to restore Time Machine from an external drive to my new MacBook Pro, the hard drive doesn't appear in the graphic. A second external drive I have does appear, but not the Macintosh HD. Suggestions?
-
IPhoto 9.1.5 won't open, downgraded from Lion back to Snow Leopard
I have tried to open iPhoto and every time I get a similar error window like I have pasted below. I have reinstalled iPhoto from iLife '11 disc. I have updated until I get the message that everything is up to date. I can't help but think that priv
-
Remove partition key from partitoned table
can somebody help me with a sql syntax to remove a partition key from a partiton table . The scenario is explained as follows: create table t1 (c1 number, c2 number ,c3 number) partition by range (c1, c2) (partition p1 values less than 11, partition
-
Je n'arrive plus à faire les mises à jour d'Adobe Reader IX, sur mon ordinateur fixe, fonctionnant sous X.P., j'ai chaque fois un message d'erreur "invalid drive lecteur L". je ne comprend pas assez l'anglais pour exécuter la manoeuvre indiquée dans