When i charge my iphone it has the plug instead of the lightning bolt showing its fully charge but the percentage will stay the same or go down. when i plug it in it turns back on but turnes right back off because its at one percent and it keeps repeating
when i charge my iphone it has the plug instead of the lightning bolt showing its fully charge but the percentage will stay the same or go down. when i plug it in it turns back on but turnes right back off because its at one percent and it keeps repeating the process. if i just try to turn it on it loads the aoole logo the the lock screen then turnes right back off. please help!!! i have a cdma verizion iphone 4 if that matters
Bring your phone into Apple for battery diagnostics.
Similar Messages
-
The fully charged battery symbol shows up (a plug instead of a lightning bolt) when it's actually not fully charged! It also stops charging! How do I fix this?
Did you already try to set it up "as new device" How to back up your data and set up as a new device
If this does not work, try again, this time without using the latest backup, in case it contains corrupt data, causing your problems. -
I'm trying to download my Master CS6 onto a new hard drive because my old one crashed and I keep getting a message saying " Cannot write the file" or "I don't have permission to access the requested resource." ? What does this mean?
Yes- it is a Mac. I went through adobes system requirements and re- downloaded supportive software. The notice seems to happen near the end of the down load with the messages above. I'll look into your suggestion. Thank you- appreciated.
-
My phone turned its self off for about 10 minutes, when it came back on it went from 84% to 18%. When I put in on the charger it shows the plug symbol as if its fully charged but the phone stays at 18%. Over time the battery dropped, but it went from 18, to 9, 3, then 1, and every time I put it on the charger it doesn't actually charge. Now my phone is off and it will not turn on.
I'd suggest taking it to apple. Warranty or no warranty.
-
Not sure if I am doing this right. This is my first time in the support community.
I imagine what I put in my heading was supposed to go in here.
I want to use Back to my mac. When I try to turn it on, it says "Back to my mac may be slow because more than one device on your network is providing network services. Turn off NAT and DHCP on one of the devices and try again. See the documentation that came with your device for information about turning off network services"
Does anyone know how I do this? I contacted my ISP (Telus in Canada) and they did not know anything (not that they usually do).Why do ISPs insist upon making things so difficult for their customers?
If you cannot get them to understand that you would prefer to use your own router over their piece of cheap junk, perhaps the information in the following will be useful:
http://keithbalomben.wordpress.com/2012/03/29/telus-actiontec-v1000h-hacks-and-i nformation/
Scroll down to DHCP Settings
You will need to log in with proper "technician" credentials. They are provided in the above link as
Username: tech
Password: t3lu5tv
... but these may or may not work. Try it, and if you cannot get anywhere at least now you know what to ask Telus to do in return for your business. -
My iphone 4 turned off yesterday very randomly. I had 88% battery when it turned off. I plugged it into the wall and it said i had no battery, then the apple came up as if it was turning on. It went black again and this keeps repeating over and over. Any help please ?
Battery could be at EOL. Try getting it replaced.
-
I have the older 2008 version of the Macbook Pro and since Friday when I closed it and opend it again the screen wouldn't come back on and I'd have to press down the power button and restart the machine again completely. Then when I turned it on it would sound like its powering up but after three seconds it would make the bleeping sound and shut down again, its fully charged and I have taken the battery out and put it back in but nothing is changing, is there a way to solve this problem?
Check this article http://support.apple.com/kb/HT1547 and this one http://support.apple.com/kb/HT2341?viewlocale=en_US
If it sounds like a RAM issue it could be one of the RAM chips has failed. You could try removing the RAM one at a time and see if it starts with one still installed. -
i left my ipod alone for a second on the bed i come back and i click the on button it wont turn on anymore and its fully charge what should i do?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
i restored my iphone 5c and it shut off and now it wont turn back on i tried to restore it nothing its fully charged and i tried to hold the home button and lock button it shows the logo and shuts off again
1st, try to do a hard reset if that does not work try this article
http://support.apple.com/kb/ts3281 -
my 2008 macbook will not turn on. the light on the corner is on. not flashing but on. its fully charged and has lion on it. please help! my classes start Monday and i need it before then!! It will turn on for a coupe seconds, and then turn off.
Take it into an Apple store for evaluation.
-
My ipod 60gb classic is showing as fully charged until I connect it to my pc when it comes up with the error message, 'please wait very low battery' and the little wheel goes round and nothing happens, can anyone explain why this is and what i can do?
I have worked my way through the assistant and nothing works. I have tried connecting in disc mode but although the screen on the ipod is showing that the device is charged and that it is in disc mode as soon as I connect it to the computer it comes up with the error message 'please wait very low battery' and stays like that until I disconnect when it appears to be OK again. I have tried on both pc and mac.
BTW the ipod is an ipod video not classic if that makes any difference.
Thanks -
Hi, my ipod nano works perfectly well when connected to my laptop, but won't even switch on when it's stand alone. Battery is showing as fully charged. Anyone know if/how I can fix this? Thanks
Take the iPod N ano to your local Apple Store or an AASP to be examined.
-
iPhone 5 has stopped receiving my e-mails. Can't access anything under Accounts to use any of the resolutions in the support pages.
Did you set up restrictions for changing account info in Settings/General/Restrictions? If yes, disable them and try again to edit your mail account info.
-
Unable to turn Wi-Fi or Bluetooth on or off because the setting is grayed out or dim.
Try to re-set it as rudegar suggests. If that doesn't work, try a restore. If that doesn't work, try a restore as new.
If the settings are still grayed out, then your phone has suffered a hardware failure. -
Why does my iphone 4s has mobile data instead of cellular data?
why does my iphone 4s has mobile data instead of cellular data?
"Mobile data" and "cellular data" are the same thing - just depends what your carrier chooses to call it.
Maybe you are looking for
-
I am writing query like select * from emp where dname = 'marketing' works fine but besise dname marketing I have marketing 2 and marketing3 so I thought I can write select * from emp where dname like 'marketing%' but it work in sql environmen
-
How to change 'z' key into 'A' key with key blinding?
How to change 'z' key into 'A' key? Although txt.setText("A") can set the text field with 'a', but it is not original input from keyboard because it cant trigger the key listener. It is possible to perform key pressing more than a key in same time? E
-
Using SequenceFactory getNext in persistent object constructor
Hi, Rightly or wrongly (maybe wrongly cos I am getting problems...) In my persistent object constructors, I am initialising the objects id field using the sequence factory getNext() method. If I run the schematool on a blank DB with no tables then it
-
Hello, I have a problem with my macbook pro. When i try to turn it on, i have this screen after i loged in: What should i do? Thx in advance
-
CFolders Thumbnails strange behavior on calling an refreshing a site
I'm trying to use Thumbnails in cFolder Objects or Folders, but they behave strange when using IE6 When loading a site with Thumbnails, it seems that it lasts very long to load the Thumbs. For example, a site with 3Thumbnails shows them after 2Minute