When i open my macbook pro the wifi connect but says no internet connection

Every time i close my Macbook Pro (early 2011 model running OSX Lion) then open it back up the wifi will connect to the right network but says i have no internet connection this lasts for about 5-10 minutes then the internet will finally work. i know it's not the router cause im connected on my phone and on other computers and they work just fine. is this something internal or something with the software?

Hi..
Try Resetting the System Management Controller (SMC)

Similar Messages

  • When i open my macbook pro- the screen lights up and then goes black-

    When I open my Macbook pro- the screen lights up and then goes black- keybook stays backlite- can not get screen to come back on. Must reboot-
    thoughts-?? Macbook is 6 months old and on second hard drive ( failure after 45 days).

    Hey! exact same thing happens to me... I use the keyboard shortcut to turn off the screen which is ctrl - shift - eject button. Then just poke a key and it wakes up again fine, it doesn't fix the problem but at elast you don't have to reboot. x

  • When I open my MacBook Pro for the first time each day, I find condensation on the glass.  What can I do to prevent the condensation?

    When I open my MacBook Pro for the first time each day, I find condensation on the glass.  What can I do to prevent the condensation?

    This thread and all the followups are hilarious, if it weren't such a serious problem. OP, you may want to add a bit more information on how this drippy screen problem occurs: where do you live, what are the weather conditions, what are you doing with the Mac when it occurs, etc.
    Yes, extreme moisture, to the extent of causing visible condensation, is Very Bad News for any electronic device, and more so with one that isn't tropicalized like the Mac. Besides trying to avoid subjecting it to such extreme temperature changes, using some kind of desiccant to absorb close range moisture and avoidint its use until it dried out, I can suggest placing some kind of absorbent material between the display and the keyboard to prevent the moisture on the glass from finding its way into the computer. Like the protective poliethylene foam protector that came with the Mac when new. Or something like RadTech's ScreenSavrz: http://www.radtech.us/Products/NotebookScreenSavrz.aspx

  • When I open my Macbook Pro it shows past date

    Hi -
    Sometimes (pretty consistently lately) when I open my Macbook Pro it shows the screen that was there when I closed it, but everything is greyed.  There is a line at the bottom that is moving across and when it finishes the color goes back to normal.  But even then, the time is from when I closed it, and the computer is unresponsive.  It will sometimes sit in this state for a couple of minutes or longer.
    This is a six month old Macbook Pro and this happens pretty regularly, and has off and on since I first got it.
    Is this just no more than annoying?  I've been using Apple laptops since 2005 and never had this happen until this machine (which is my third personal one - I support two others).  Any ideas on cause?
    Thanks
    Craig

    Some users have reported solving this problem by resetting the NVRAM (PRAM.)
    If you've installed something called "iCleanMemory," or any other third-party software that is supposed to "clean" or "free up" memory, remove it according to the developer's instructions after backing up all data. Reboot and test. If there's no change, continue.
    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches. 
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and  Wi-Fi on certain models. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • When I open my MacBook Air the keyboard comes up along with the screen and does not stay still?!

    When I open my MacBook Air the keyboard comes up along with the screen and does not stay still. So I need to hold down the keyboard while i open it. Other than that it works fine despite the fact that the fan noise some times is loud and sometimes it's getting warm at the base. I wonder if this can be fixed if i go to one of the apple branches.

    Yes. Take the computer to the Apple store to have it fixed.
    Best

  • HT2341 When I first attempt to power on my MacBook Pro, the LED blinks but the MBP doesnt turn on. However when I try a second time the LED blinks but my Mac turns on. Is this a problem with the hardware and can it be fixed?

    When I first attempt to power on my MacBook Pro, the LED blinks but the MBP doesnt turn on. However when I try a second time the LED blinks but my Mac turns on. Is this a problem with the hardware and can it be fixed?
    Also, I apparently have to replace my battery. Could the problem have any relevance to a dead battery?

    Have you held the power button down for 10+ seconds?  That should turn it off.
    Ciao.

  • I just downloaded the new version of Firefox (ver 4). Now when I open Firefox I get the address bar but the information part of my screen is blank. This happens on all web sites. How do I fix this? IE works fine.

    I just downloaded the new version of Firefox (ver 4). Now when I open Firefox I get the address bar but the information part of my screen is blank. This happens on all web sites. How do I fix this? IE works fine.

    Did you check your security software (firewall)?
    A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
    See:
    * [[Server not found]]
    * [[Firewalls]]

  • HT4889 Hi. I`ve just started transferring from my old Imac to a new Macbook, using the WIFI. But I realize it will take days to get it done. Can I cancel the process, and start over again using the thunderbolt port? Without causing any trouble?

    Hi. I`ve just started transferring from my old Imac to a new Macbook, using the WIFI. But I realize it will take days to get it done. Can I cancel the process, and start over again using the thunderbolt port? Without causing any trouble?

    See Pondini's Setup New Mac guide for possible answers.

  • When I open my macbook pro it's not automatically connected to the wifi at home

    Hello,
    When I open my mac it's just usally is connected to the wifi itself but now I keep getting that I now have to wait 10 seconds or longer after opening my mac to have my mac connected to the wifi ! Has it something to do with Mavericks ?
    Kind regards

    Some users have reported solving this problem by resetting the NVRAM (PRAM.)
    If you've installed something called "iCleanMemory," or any other third-party software that is supposed to "clean" or "free up" memory, remove it according to the developer's instructions after backing up all data. Reboot and test. If there's no change, continue.
    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches. 
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and  Wi-Fi on certain models. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • Is there any way of sharing my Macbook Pro's Wifi connection to iPhone 4 (Not Using iPhone as hotspot for laptop the other way around)

    So a nasty smash destroyed both Front & Back of my iPhone 4, and since having them replaced the Wifi signal has been really weak.
    I have seen other posts about screen replacement having to be done by going through the antenna, so something could be missing, or done incorrectly during the screen repair. Will definately be taking it back to the shop and finding out if It was put back together properly.
    In the meantime I was wondering if it is possible to share my Macbook Pro's Wifi (always full signal in my house) directly to my iPhone either using USB cable or through bluetooth. It's not been too much of a problem but it would be nice to use my iPhone in bedroom using the Macbooks good signal.
    Note: The replacement front screen on iPhone has a small gap >1mm between the screen and centre metal casing on the left side just above the Silent/Loud Switch, which can be noticed by light leaking through the gap. The metal casing also still has a small dent between the volume down buttons and silent/loud switch, again nothing drastic 1mm maximum

    Here is the start of the setup:
    Click on the Wi-Fi Options button and provide the needed info:
    Click on the OK button. Now check the Internet Sharing box to turn it all on. If the port box you checked is no longer checked, then uncheck Internet Sharing, check the port box again, then check the Internet Sharing box again.

  • MacBook Pro loses wifi connection upon wake since I bought a new AirPort Express

    Hi. I've been using Apple devices and computers since february 2008 and had no problems until now. I currently own an early 2011 13" MacBook Pro and a PC running Windows 7 and Ubuntu 12.10. Until early February, I used a 2nd gen AirPort Extreme to connect to wifi upstairs, being connected via Ethernet to my ISP's modem located downstairs which provides a weak wifi signal (of course my ISP says it's impossible since their modem is the best on the market), not even compatible with Apple's wifi systems (all other French ISPs modems are compatible with it), that's why I had to get a 30 ft ethernet cable running down the stairs. My connection was lost everytime I went upstairs/downstairs so I bought a new Airport Express to replace my ISP's modem wifi signal and I'm using my AirPort Extreme to extend the wifi network upstairs. Now all my devices and computers have a strong wifi signal anywhere in my house with only one downside: My MacBook Pro (and only it) loses the wifi connection upon wake after sleep and I have to disconnect/reconnect it manually. I didn't bother installing Windows on it as I removed the Superdrive to setup a DIY Fusion Drive a few months ago so I can no longer boot optical medias and I can't know if it's a hardware or software problem. Again, everything was working all right on it until I changed my Wifi network configuration a month ago when I bought my Airport Express.
    Can anyone help me ?
    Thanks in advance.

    Well this isn't making sence. 
    What is the model # on your extreme?

  • 2008 MacBook Pro with wifi connectivity issues

    Hello all,
    My MacBook Pro has stopped connecting to my wireless internet at my house. Works fine when connected to the Ethernet, but no luck with wireless. My iPad, iPhone, and wife's MacBook Pro have no issues picking up the signal. When I attempted the network diagnostics, the wifi will not turn on. The button that enables you to TURN ON WIFI does not respond. I made a trip to the local apple store where they reset the wireless and it worked fine in the store. Took it home and same problem still existed.   Diagnostic report at the apple store showed no problems with wireless card.
    Any thoughts, comments, or wisdom would be appreciated!

    Apple released a firmware update for your MBP model to enable it to charge properly with the new-style adapters, after failures to do so were widely reported. Here's an article about the problem:
    http://support.apple.com/kb/TS3499
    And here's a link to the update:
    http://support.apple.com/kb/DL1311
    As with all firmware updates, it's essential to follow the installation instructions to the letter.

  • HT201263 All I get when I open my iPod is the USB connection to iTunes image.  Although it says the iPod needs to be restored, when I go through that process it says it cannot restore because "No device detected".  I don't know what else I can do??

    All I get when I turn iPod on is the USB connection to iTunes image.  Then the system tells me that I have to restore the iPod.  When I go through that process it says it cannot be restores because the device cannot be located.  What do I do??

    - Reboot the computer
    - Try another cable and USB port
    - Try placing the iPiod in DFU mode and then restoring
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar

  • What is the cracking sound when I open my MacBook Pro lid?

    When opening and closing MacBook Pro lid, it makes a cracking sound. Does anyone have an idea what it could be? It's not the hard drive because Geek Squad ran a test and everything passed.

    Try this:  Loosen the screws in the rear of the MBP (by the hinge) and re-torque them.  See if that will alleviate the problem. You will need a 00 Philips driver.
    Ciao.

  • Put to Sleep and  Don't wake up when i open my macbook pro

    Hello,
    i have a Macbook pro 17' (2,33ghz) using leopard 10.5.2 with all the latest update.
    Everytime i put my computer to sleep for more than 10 minutes (random time), when i try to wake up nothing happen, i hear a strange noise of the HD for about 2 seconds and the screen stay Black.
    When i close the computer again, the light stay On, when i open the computer again nothing happen, the screen is black, no buttons works, nothing happen.
    So i have to press the Power button for a few seconds and then turn on my Mac again.
    this happen to me every day !
    i try:
    Remove the charger = Same Problem
    With the charger = Same Problem
    With Apple Bluetooth mouse = Same Problem
    Without Apple Bluetooth mouse = Same Problem
    With External HD = Same Problem
    Without External HD = Same Problem
    when i try to wake up the Mac, I wait for more than 10 minutes and nothing happen.
    i see the Log's and i can't see antything Wrong.
    this is not the first time i have this problem
    in 10.4.8 i have the problem, when i update to 10.4.9 "fix the problem" until 10.5.2
    i have the AppleCare.
    i dont know if this is a Hardware or Software problem and if the guarantee cover this?
    thinkin that this could be a HD problem so i check in the disk utility and everyting is OK.
    Thanks!

    Well. in my searching i find an """"Answer"""
    Some body was talking about that the new's Mac have something called "Safe Sleep" so when someone sleep the Mac the Information of the Ram make a copy in the HD this can take for 30 seconds to a minute. In this time, if you move the mac or do something else, generate a error and corrupt the Information of the ram and the Mac stop working.
    Say that to remove this "Safe Sleep" have to open the terminal and:
    The Unix command to disable SafeSleep is:
    sudo pmset -a hibernatemode 0
    To re-enable SafeSleep, the command is:
    sudo pmset -a hibernatemode 3
    Maybe Apple going to Fix this in future Updates.
    Sorry for my English !

Maybe you are looking for

  • Time Stamp Conversion

    Hi,       I need to convert the following time stamp into date and time. could any one help me how to do this? Input format: 2008-05-19T01:00:00Z Convert statement wont work as it has characters in it. At present i have converted by using split statm

  • How can I tell if I have SATA 3

    Cannot find it in the specs for HP Pavilion m6-1035dx Nevermind, found a post to run PCWizard, it say's I have 6Gbs 

  • Set Default value for transaction code F-36

    Hi I need to set default value to feild special G/L indicator in transaction code F-36 How can I do that. Please advice. Regards Kesharika

  • Keep getting ioexception... please help

    I have two classes. Class ItemRecord defines the record in my input file and OrderCalculator4 opens the file and should load some arrays up with the data in the file. But it keeps throwing the first ioexception where i have "Error opening file". I ha

  • SG printed as SG instead of the whole name Singapore whrn using PLD

    Good Afternoon, Please guides us on any set up requirement. We encounter an error in PLD. When bussiness partner has bill to address in SG. our PLD is printing this country as SG intead of the whole name Singapore We currently using 2005B singapore L