When I tried to shut down my IPad( by sliding the red bar) the spinning gear started spinning and it won't shut down. The gear has been spinning for 18 hrs now. What is causing this and how can it be fixed?
When I tried to shut down my other Ipad(by sliding the red bar) the gear symbol started spinning but it won't shut down--the gear is still spinning 18 hrs later.
Try and force iPad into Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.
Similar Messages
-
My facetime is not verifying my email though it shows an email has been sent for verification but no email is received. How can I have my facetime back.. Pls help.
I have it set up on both of mine and I know she has the app what I would have to check is if it is enable in hers, although prior to the cancellation of service she used to be able to make the calls, my concern is why I can't which is possible that it needs to be enable. Thank you!
-
I just purchased the I 4S and at least once a day, it will say Invalid Sim, what would cause this and how do I fix it?
Then, if there's any data on the drive that you want to keep, you have to back up before you do anything else -- assuming it's still possible.
Basically you have three options:
1. Install a copy of the Mac OS on an external hard drive, boot from it, and copy the data from the internal drive.
2. Start the problem Mac in FireWire target mode (command-T at startup) and connect it to a working Mac with a FireWire cable. The internal drive will mount as a FireWire device.
3. Remove the internal drive and mount in an external enclosure on another Mac.
Once you've backed up, follow the sequence in the support article linked below. The article is somewhat outdated. Where it refers to booting from an installation disc, you should boot from your recovery partition (if running Lion) by holding down the key combination command-R at the chime.
Mac OS X: Gray screen appears during startup -
I never have noticed this problem until about 2-3 weeks ago & it occurs after I've been online for awhile. When I click through my open tabs, each of them is written in distinctly different Chinese, as if it's translating what ordinarily would have been in English. I have been using Firefox on this computer for over a year, never have had this issue before and have never done anything to activate any translation function.
I never have noticed this problem until about 2-3 weeks ago & it occurs after I've been online for awhile. When I click through my open tabs, each of them is written in distinctly different Chinese, as if it's translating what ordinarily would have been in English. I have been using Firefox on this computer for over a year, never have had this issue before and have never done anything to activate any translation function.
-
My ipad will not start up, it has the swirl in the center of the screen and has been there for 30hrs now, what can I do?
First thing to try is a reboot of your iPad. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider until the Apple logo appears. Let go of the buttons and let the iPad restart. See if that fixes your problem.
-
Apple Support says that my serial number is invalid. I provided the correct number. What would cause this and how can it be fixed. Ipad II.
Things that could cause it:
you bought a fake
you allowed an unauthorized person to "repair" the iPad, replaced the logic board -
I have recently got a new replacement iPhone 4. Since I got this I have found that my data allowance is getting used up during the night while my phone is charging on the bedside table. How an I find out what is causing this and stop it happening? Some nights the usage is 150 meg!
You can not access the backup directly.
Did you restore your replacement from this backup?
If so then you already have everything in the backup on your device.
If not, you can wipe the device and restore from this backup:
Settings > General > Reset > Erase All Content & Settings
What is it you are worried about losing that isn't already on your current device? -
MacBook was restarting on its own and now is not powering up. What could cause this and how to troubleshoot?
When did it happen? After updating/upgrading? or just randomly?
You can try to perform a SMC reset and resetting the PRAM:
SMC Reset -> http://support.apple.com/kb/HT3964
PRAM/NVRAM -> http://support.apple.com/kb/ht1379 -
All my photos are importing out of order. For example, if I have images 1,2,3, and 4.., the order they show up in is 2,1,4,3. What could cause this and any ideas how I fix it?
One thing, don;t think of them as being imported in any one particular order.
The order of the images is completely fluid, you can change it anytime you want to suit your needs at that particular moment.
As Léonie showed you select the order you want to see the images in by selecting the item you want to sort on in the pull-down.
The only time fluid sort order can be a problem is when you export groups of images. If you put the images into a particular order in Aperture when you export them and view them in the Finder the order they are in may very well be different. In this case you could give names to the images that include a sequence number or index.
Then when they are viewd in the Finder they will be in them same order they were in in Aperture.
regards -
I have an iMac and under devices in the sidebar that name has changed from iMac to iMac(1) to iMac(2)...and is now at iMac(9). What is causing this and how do I correct it?
Sometimes this message means that you have two simultaneous connections to the same local network: probably Ethernet and Wi-Fi. If applicable, disconnect the Ethernet cable or turn off Wi-Fi.
Sometimes it happens because a device that gets its network address from the router wakes from sleep, and the address it was using before has been assigned to another device.
A third-party wireless router that has incompatible settings or firmware may be the cause. In that case, refer to the manufacturer or ISP for support. Restarting the router may help, temporarily.
Rename the computer in the Sharing preference pane. -
My MacBook Pro has been having difficulties at startup. It sometimes locks and doesn't get past the white screen. It has also locked up several times and gotten a green stripes across the entire screen. What is causing this and how do I fix it?
You don't, take it to Apple for repair.
This might interest you if it's too old to fix.
My computer is not working, is my personal data lost? -
I have a Macbook Pro purchased brand new. I take high quality pictures for customers, these display perfect on my laptop but appear CORRUPT on a USB stick. What is causing this? I can't seem to fix this issue. PLEASE HELP!!
I really need this issue resolved it is driving me insane!!! How can the images appear perfectly fine on my laptop then when transferring over to a USB stick they just corrupt!?Check out this site:
http://osxdaily.com/2012/04/22/format-drive-mac-pc-compatible/
That will show you how to format a USB stick for use on both PC and Mac.
If the problem continues take it to an Apple store and have them check it out.
>Also what s exFAT?<
From:
http://en.wikipedia.org/wiki/ExFAT
"exFAT (Extended File Allocation Table) is a Microsoft file system optimized for flash drives.[3] It is proprietary and patented."
That first site explains it at length. -
I have a MacBook Pro. When surfing the web it will eventually slow to a crawl. When this occurs, there will be a small multi-colored wheel spinning until my latest command is handled. What is causing this and is there a way that I can modify or prevent this from happening? Is there a setting that will prevent this?
When you next have the problem, note the exact time: hour, minute, second.
If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Scroll back in the log to the time you noted above. Select any messages timestamped from then until the end of the episode, or until they start to repeat. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V).
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting. -
Photoshop elements 9 was pre installed on my pc when I bought it and now it has been deleted, I don't have any serial number. How can I get it back?
Check the papers that came with your PC or the web site of the vendor. OEM versions are either on the recovery discs they provide or can be downloaded from their site.
Mylenium -
My iPad has been disabled due to wrong passcode which I have forgotten,How can open it again?I'm so desperate right now
If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup).
If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.
You may have to force iPad into Recovery Mode
http://support.apple.com/kb/ht1808 -
I'm in London for a semester and I met someone here. My iMessage has been useful for chatting with friends from home, but I'd like to add this guy to my contacts and iMessage him. I can't iMessage him (he has functional iMessage on his iPhone). Why doesn't my phone recognize him to have iMessage? Do I have to turn my data on and my airport off to send a message before it recognizes that he has iMessage?
Call AppleCare, because, according to Apple, removing the devices from your support profile should have fixed this issue. You can also try changing your Apple ID password, but given what you've done, I doubt this will help.
Maybe you are looking for
-
How can i convert/invert colors in a scanned pdf blueprint?
We have several large format blueprints to scan in and I want to change the blue to white and white to black so I can view/print them. Is this possible?
-
How I "fixed" my iPod after the latest update screwed everything up
I am not sure if this will help anyone but here is what I have been through and done. I also don't know if this "fix" will last. So far it has been 24 hours and my iPod still works. To be honest I was surprised anything worked since this whole fiasco
-
Does Using Your iPod Touch While It's Charging Waste Charge Cycles?
If my iPod Touch is 100% charged and I use it while it is plugged in to my wall charger will it waste charge cycles as I use it?
-
Hi everyone, In SAP APO-DP it's possible to specify a cannibalization group when promoting a product. Thus the promotions for the other Products in the cannibalization group a calculated automatically. Is S&OP on HANA offering a similar feature? If n
-
Help, why am i getting an error?
i have the following code, trying to find the smallest of 3 integers that i will input, keep getting an error message, says that "scanner" is not a reconized symbol?? import static java.lang.Math.*; public class dr { static Scanner console = new