Window Server cannot connect to Router?

I have installed a windows server 2012 r2 datacenter on virtual box using windows7. I installed AD Ds, DHCP and DNS on it. To install DHCP on window server I first disabled the DHCP service on my router and then on server I changed the ip address to static(10.1.10.2)
and added default gateway as 10.1.10.1 (IP address of router). But by doing that my server and other computer connected to network are not connecting to router.(i tried pinging router)? I am a student and I am working on a test lab using d-link router which
is further connected to main house router.
Thanks

Hi please check this artical hope this helps
https://blogs.oracle.com/fatbloke/entry/networking_in_virtualbox1

Similar Messages

Wireless print server cannot connect to router

Hi - I just got the FiOS installed. When I went to set up my print server via wireless, it has failed. It has previously been connected via Ethernet and worked just fine. The print server thinks its connect to the AP/router but the FiOS router does not see it. I went into the system logs and see the following errors:
Feb 13 09:56:29 2009 System Log Message daemon.warn sys_if_ioctl_mii_execute:507: Both tried MII ioclts 8947/89F0 failed: Operation not supported.
[repeated 2 times, last time on Feb 13 09:56:29 2009]
Feb 13 09:55:06 2009 System Log Message daemon.warn DNS: unknown PTR name format
[repeated 4 times, last time on Feb 13 09:55:51 2009]
Any ideas?
Solved!
Go to Solution.

I figured out how to fix this. Took a while but here it is if other run into the problem:
http://forum.verizon.com/vrzn/board/message?board.id=FiOS_Internet&message.id=5457&jump=true

Reporting Services Server cannot connect to the DPM database. ( dpm 2010 )

Reporting Services Server cannot connect to the DPM database.
To repair the configuration, follow steps for repairing DPM from DPM Setup Help.
ID: 3001
i can not try the Recommended action from error codes catalog because i did not found Change reporting
password

Hi,
We have had several customers report this after installing DPM 2012 R2.
To get past the below error while scheduling reports to be mailed.
Reporting Services Server cannot connect to the DPM database.
To repair the configuration, follow steps for repairing DPM from DPM Setup Help.
ID: 3001
Perform the following steps as necessary:
1. Created a new local group called "DPMDBReaders$<DPMServerName>"
2. Created a new user called, "DPMR$<DPMServerName>" and added this user to DPMDBReader group that we created on step 1.
3. Open SQL management studio and add the DPMDBReaders$<DPMServerName group to Logins under Security in SQL Management Studio.
4. Modify the properties and under General – change the default database to the current DPMDB name.
5. Under User Mapping – select the current DPMDB name and check the db_datareader checkbox.
6. In SQL Management Studio, navigate to the Databases > DPMDB > Security > Users > and select the DPMDBReaders$<DPMServerName>" group.
Right-click the DPMDBReaders$<DPMServerName>" group and select properties. Under the
Securables section, click on Search. On the add objects dialog, click OK.
On the Select Objects dialog, click the Objects type, then check the
stored procedure checkbox. Browse and add the following two stored procedures
“Prc_MOM_Heartbeat_Get” and “prc_MOM_ProductionServer_Get”.    Grant the Execute permission for both of the stored procedures added.
7. In SQL Reporting Services Configuration manager, under Report Manager URL - click on the link to open the portal (http://localhost/Reports)
      i. Click on the DPMReoprts_GUID to open the DPM reports.
      ii. Click on the DPMReporterDataSource
      iii. On the poperties page, enabled "Credentials stored securely in the report server" on DPMReporterDataSource configuration page and added “DPMR$<DPMServerName>” user account that we created in step 2.
      iv. tick "Use as Windows credentials when connecting to the data source."
      v.   Click ‘Test connection’ on the same page to verify whether it can connect successfully.
8. In SQL Reporting configuration manager - change the Service Account to use build-in account: Network Service
9. Reboot the DPM Server.
10. You should then be able to schedule e-mailed reports.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT] This
posting is provided "AS IS" with no warranties, and confers no rights.

DPM 2012 R2 Rollup 1 x64.. cant save scheduled report.. gives error: "Reporting services server cannot connect to the dpm database"

The error also has "to repair the configuration, follow steps for repairing dpm from DPM setup help ID: 3001
I tried the solution outlined here:
http://social.technet.microsoft.com/Forums/en-US/8be919ee-f358-47a4-9cc3-d23eb05d3f18/system-center-2012-r2-dpm-smtp-issue-reporting-services-server-cannot-connect-to-the-dpm?forum=dataprotectionmanager
and also the graphical depiction here: http://www.ms4u.info/2014/01/reporting-services-server-cannot.html
I tried these steps, but everytime i try to change it, it tells me:
"The permissions granted to user 'domain\userid' are insufficient for performing this action rsaccessdenied..
Nothing seems to work..
I thought if i went into sql management studio and made sure my userid had admin rights to the db it would work.. but i cant change it there (via integrated security).. i believe i need to login as SA, but i dont recall the password for SA, though it appears
i can change the SA password from within sql management studio.. i'm unsure if doing so will break DPM though or is even needed to fix the reporting integration issue..
Any thoughts on this?
Thanks
Tech, the Universe, Everything: http://tech-stew.com

Using:
data source="servername\MSDPM2012";persist security info=False;initial catalog=DPMDB
I used the domain sqlservice account and test connection was ok.
However.. accessing reports still crashes in the MMC
Tech, the Universe, Everything: http://tech-stew.com
When i recreated the db.. i called it Reporting2 or similiar..
Then the reports folder i created called "Reports Folder"
Then datasource name "reports datasource"
The issue here is that the DPM reports in the reporting web interface are gone, since this is a new DB.. how do i redeploy them
Tech, the Universe, Everything: http://tech-stew.com
i went back into the sql reporting services area.. hit change db.. chose the original .. then back to the url.. went to the OLD reporting services folder and datasource.. added the connect string and now reporting area works.. so does scheduling..
Problem now solved
Tech, the Universe, Everything: http://tech-stew.com
Oops spoke too soon.. the first time i set it to do "status" as a schedule.. it seemed to work (clicked ok, no error).. went back and added an email notification..
Now i'm getting.. "an error occurred causing the reporting job to fail" "system files may be corrupt".
Seems to only occur if i try to add the email address portion
Tech, the Universe, Everything: http://tech-stew.com
rechecked the datasource.. i think there was an error in the connect string.. now everything seems to be working.. email notifications and all.
Tech, the Universe, Everything: http://tech-stew.com

2008 R2 printer server, cannot connect to printer, access denied, Windows 7 OS only

Deployed new Windows 2008 R2 domain controller, added print and document controll. Added several network printers on R2 server. We currently have mostly Vista biz clients but half a dozen W7Pro clients also. The Vista clients connect to these new network
printers, no problem but none of the W7 clients will connect. I select the printer from the drop down directory list and select to load the drivers, the system starts loading drivers and then right before it finishes it stops with error message, "Windows cannot
connect to the printer. Access denied. Again, this happens only with the W7 clients on our domain, Vista works fine.

By default, the security settings for Windows 7 and Server 2008 R2 allow users who are not members of the local
Administrators group to install only trustworthy printer drivers, such as those provided with Windows or in digitally signed printer-driver packages. You may want to install printer-driver packages on the print server
or in the clients. More details can be found this page: Cannot
connect to printer, Access denied -
http://www.chicagotech.net/server/print3.htm
Bob Lin, MS-MVP Networking, Internet, Routing, VPN Troubleshooting on
http://www.ChicagoTech.net
How to Setup Windows, Network, VPN & Remote Access on
http://www.howtonetworking.com

Cannot connect to router (Windows is fine!)

I cannot get my computer to connect to my netopia router at my office. I've been on the phone with tech support for around 30 minutes and have been through all of the regular settings and resets.
When I run bootcamp and load my computer with Windows, I can connect to the router fine (ethernet and wireless).
When I'm on the Mac, I get connected (green light or connection signal from wireless), but I get no internet and cannot access my router.
I have a suspicion that is has something to do with IP addresses. My router IP address is 192.168.1.254. When I log on wirelessly it says my IP address is 192.168.2.23, which is incorrect. When I plug in the ethernet, my address is 192.168.2.21, which must also be incorrect. Also of note is that under search domains "Belkin" is in gray. I'm not even connecting to a Belkin router!
I do want to note that for some strange reason, after a bunch of resets, sometimes I am able to connect wirelessly with a correct IP (192.168.1.13 or something), but then I lose the connection and can never get it back.
What gives?!?

Are you sure your Mac is set to obtain its IP address via DHCP?
It sounds a lot like your Mac has a manual IP address or addresses set.
If that's not the case, your office may (erroneously) have multiple DHCP servers running, which could create the problem you're seeing.
In such an situation it's a pure race condition as to which DHCP server you will obtain an address from and whether you will keep a good one once obtained.
But check for the manual IP address setting first.

Itunes on windows 7 cannot connect to the iPad update server

I have downloaded my windows updates, installed the newest version of iTunes, my internet is fully opel; however, I am unable to connect to the iPad update server so that I can restore my iPad 1 that is giving me trouble. *Sighs* Please help :/

Let's try the following document with that one.
iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
(If the "Automatically detect settings" checkbox is already checked, try unchecking and rechecking it and clicking OK.)

CiscoWorks ANI server cannot connect, Joe Clark please help

Joe, if you see this, please help
I noticed yesterday I was getting some Java errors when opening different modules of Cisco Works, Campus Manager, RME.
I rebooted the server and everything seemd to be working fine. I tried to set up Notification Services after the reboot and it seemed to go without incident.
This morning Common Services shows
"DCA Server is down or inaccessable"
Campus Manager shows:
"Cannot connect to ANI Server since it is down"
Here is a clip from ani.log:
2007/12/28 08:00:08 Thread-76 ani ERROR DBConnection$ConnectionCreator: Failed to establish DB connectivity because: java.sql.SQLException: JZ006: Caught IOException: java.net.ConnectException: Connection refused: connect
2007/12/28 08:00:08 Discovery ani ERROR DiscoveryTimeBaseStat: Failed to enumerate Wbu table names because null
2007/12/28 08:00:08 Discovery ani DiscoveryTimeBaseStat: {NumDevices=31}{NumDiscovered=0}{NumDeleted=0}{DPH=14695}{OPH=0}
2007/12/28 08:00:08 Discovery ani DiscoveryTimeBaseImpl: completed: Discovery in 8578 ms
1198846847568 December 28, 2007 8:00:47 AM ES_SVRCWLMS__1198788044958(127) SVRCWLMS Error EDSSY0012: Cannot connect to EDS.
1198846910568 December 28, 2007 8:01:50 AM ES_SVRCWLMS__1198788044958(127) SVRCWLMS Error EDSSY0012: Cannot connect to EDS.
1198846973568 December 28, 2007 8:02:53 AM ES_SVRCWLMS__1198788044958(127) SVRCWLMS Error EDSSY0012: Cannot connect to EDS.
Reboot has not helped this morning.
I just found out we did some WIndows patches a couple of days ago.

Joe,
Is there any way this could have been related to me setting up Notification Services?
Something I noticed yesterday is that when setting up "Event Sets", nothing shows up.
Per the document (and I saw this yesterday after a reboot of the server (most likely what caused the problem), I should see a list of items to trigger notification and I can configure nine different sets.
But, I see "No Records" on the Event Sets page.
I see the A,B,C etc, but nothing under them.
After a reboot yesterday, then I saw the items and checked off for the different event sets.
My goal is to have an e-mail alert when switch or router interfaces go down , or high utilization of fragmentation.

WRT160N v3: Cannot connect to router setup web page with current Firefox or IE

Every time I try to connect to the admin page of my router, I get "The connection to the server was reset while the page was loading." This happens with FIrefox 11, and started when I upgraded to 8 or 9. A machine running FF 3.6 does not exhibit this problem; I get right in. What IE 9 says is "Internet Explorer cannot display the webpage" (after complaining about the expired certificate).
I ran Wireshark to see if I could learn anything, but all I could figure out was this:
https handshake was OK.
First TLS packet is received by router, which then immediately issues a reset and ends the connection. I don't know why.
Has anyone seen this? or have I got a screwed up configuration (or router)?
Solved!
Go to Solution.

castor wrote:
"The connection has timed out", seems to affect servers at MozilllaZine, for Firefox on Windows...
I'm not sure what this has to do with my problem; my difficulty is only in trying to talk to the router configuration page. Everything else works just fine.
~~ Tools > Options
~~ Advanced (tab) -> Network (tab) > "Setting"
~~ (X) Auto-detect proxy setting for this network
I have "use system proxy settings". Since this is a home network and I'm not using a software proxy on my machine, I know there is nothing between me and the router.
Second, let me know if you have enabled 'https' in the router management page. What is the IP address on the computer when connected to the router. To check the IP address that you are getting from the Router... You can check the IP address in the following manner:
# Click on Start -> All Programs -> Accessories -> Command Prompt.
# A black pop up box should come up, type: "ipconfig /all" …
This is not going the right direction, but to satisfy your curiosity:
   IPv4 Address. . . . . . . . . . . : 10.244.122.142(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : 10.244.122.1
   DHCP Server . . . . . . . . . . . : 10.244.122.1
These are correct. (Since my telco DSL has me behind its own NAT router and has assigned my modem address 192.168.1.2, so I could not use Cisco/Linksys's manufacturer default address settings.)
There check the IP address and Default Gateway under LAN….
If it provides the valid IP address then try to connect the router to a different computer and then try to open the router setup page...
I have a linux virtual host (thanks to VMware) now running Firefox 5, and it can talk to the router setup page just fine, once I accept and save the invalid certificate the router presents, at https://10.244.122.1. So I conclude the problem is to do with the later version of Firefox (currently 11, but I had this problem with 10 and maybe with 8 and 9).

IPad iOS 4.2.1 WIFI problems (Server cannot connect)

my iPad is experiencing problems where after 5 minutes of browsing pages stop loading and I get an error saying cannot connect to server. any ideas? my router is lnksys and this is getting really annoying to renew cache evey 3 minutes.

Welcome to the Apple Discussions.
One solution that has helped some users of Linksys and Belkin routers in particular is to power cycle the router. Make sure it is completely shutdown, not just reset.
Then reset the network in the iPad.
And if the problem persists, change channels in the router, there may be interference from another network causing part of the problem.

Multiple SGD Gateways to one SGD server - cannot connect

I am having an issue bringing up a new SGDG.. We have all the certificates and gateways configured, but I seem to be running into the --security-gateway setting issue.
Does anyone see an issue with this?
Both SGD servers sit in a DMZ, which are NATTed 172.16.254.41 and 172.16.160.10, i have my SGD server NATTed to 172.16.(254/160).35 and I've tested both port 443 and 5307 from sgdusa2 and they can communicate fine.
./tarantella config edit --security-gateway "172.16.254.41:sgdg:sgdusa.XXXXXXXX.com:443;172.16.160.10:sgdg:sgdusa2.XXXXXXXXX.com:443;*:direct:amralbvdi01"
My sgdusa (172.16.254.41) gateway works fine, but when I try to use my sgdusa2 gateway the client never connects and errors out with "Cannot connect to server amralbvdi01.XXXXXXX.com:5307"
Thanks
Dave

Dave wrote:
./tarantella config edit --security-gateway "172.16.254.41:sgdg:sgdusa.XXXXXXXX.com:443;172.16.160.10:sgdg:sgdusa2.XXXXXXXXX.com:443;*:direct:amralbvdi01"
The delimiter in your command is invalid, separate each filter-spec entry with "comma's"
Anyway, you do realize that the "IP addresses" you've specified in your filter-spec apply to "client" connections, not "gateway" connections, right?
That is, a client with the ip address .41 will route through gateway sgdusa, a client connecting with ip address .10 will route through sgdusa2, and everyone else will connect directly to amralbvdi01 - not sure that's what you want.
And why two gateways for one server? For a load-balanced deployment, you'll want a load-balancer, like:
http://docs.oracle.com/cd/E19351-01/821-1924/bbjbbijh.html#bbjdeeeh

Help: FORMS SERVER cannot connect to database

Hi:
I've installed oracle 9i database and oracle 9ias 1.0.2.2.2a.
I configured FormsServlet and it's working very well as i suceed my test in http://machina.domain/servlet/oracle.forms.servlet.ListenerServlet!
The problem is that i cannot connect to the database and i got the error ORA-12203 TNS: Unable to connect to destination!
I've changed jserv.properties as recommended in 9ias 10222 release notes by commenting the wrapper.env=ORACLE_HOME in OJSP because it conflicts with forms server home.
I've read all about this, and i still cannot connect to the database.
I'm using a forms servlet configuration with IE JVM.
If anyone can help me... i apreciate it!
Ricardo
PS: I can't understand why oracle keep sending huge amounts of releases of products and everytime they send a new release, that new release keeps coming with new bugs.

Attention : this error just happen with formsservlet not with jinitiator http normal connect mode.
MORE INFO:
MY 806_HOME NET80 TRACELOG
Fatal NI connect error 12203, connecting to:
(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=online2.my.domain.pt)(PORT=1521)))(CONNECT_DATA=(SERVICE_NAME=neo.my.domain.pt)(CID=(PROGRAM=C:\ORACLE\806\bin\ifweb60.exe)(HOST=ONLINE2)(USER=SYSTEM))))
VERSION INFORMATION:
TNS for 32-bit Windows: Version 8.0.6.3.0 - Production
Time: 07-MAR-2002 15:34:02
Tracing to file: c:\logtracenet80.trc
Tns error struct:
nr err code: 12203
TNS-12203: TNS:unable to connect to destination
ns main err code: 12538
TNS-12538: TNS:no such protocol adapter
ns secondary err code: 12560
nt main err code: 508
TNS-00508: No such protocol adapter
nt secondary err code: 0
nt OS err code: 0

My TMG server cannot connect with Outlook .

I have TMG server connected with proxy server , i have added the record for email and added the IP address for my mail server ( outcoming , incoming ) now i can ping to the mail server but when i configure the outlook still cannot connect to your server
what should i do

Hi
As per the information and details provided by you, to connect the TMG server with Outlook please follow these steps: -
We first need to import the SSL certificate for the site on the TMG firewall. For that, click Start/Run and then type mmc.exe. From the drop
down menu, choose File > Add > Remove Snap-in. Select Cetificates, and then click on Add.
After that, follow these steps: -
Select the
Computer Account option.
Select the option to manage the
Local Computer.
In the console tree, expand the
Certificates node. Expand the Personal folder, then right click the
Certificates folder and choose Import.
Enter the location of the certificate file you exported previously.
Enter the password and optionally mark the private key exportable.
Accept the password and optionally mark the private key exportable.
Accept the default option to
Place all certificates in the following store.
In the TMG management console, right click the Firewall Policy node in the console tree and choose New, then
Exchange Web Client Access Publishing Rule.
After that, give the publishing rule a descriptive name.
Select Exchange Server 2010 from the drop down list, and then select the option to publish
Outlook Web Access.
For demonstration purposes, we are publishing a single CAS server, so we will choose the option to Publish a single web site or load balancer.
Select the option to
Use SSL to connect the published web server or server farm.
Enter the name
of internal web site.
Select the option to accept requests for a specific domain, and then enter the
Public name of the web site.
Create a web listener for the site by selecting New, and then enter a descriptive name for the listener.
Select the option to
Require SSL secure connection with clients.
Select the network to listen for incoming web requests.
Choose Select Certificate and then select the certificate you imported previously.
Select the option to use HTML Form Authentication and Windows to validate credentials.
If required Enable the SSO.
The authentication method used by
TMG must match the authentication method configured on the web site. Since we enabled basic authentication on the web site, we will choose
Basic Authentication here.
If you wish to grant access to OWA only to specific users and /or groups, add them here,. Otherwise, accept the
default All Authenticated Users group.
To confirm operation, click the Test Rule button.
TMG will test the rule and report the success or failure accordingly.
I hope this information will be helpful for you.
Thanks and regards
Shweta@G

IMac 27": Windows 7 cannot connect to wireless internet

I just installed Windows 7 on my iMac (new model 2011) on another partition, so I now have both OS X and Windows 7, and I cannot connect to my Wireless Network in Windows 7, but I can in OS X.
I've tried basically everything and looked in millions of threads to find a sollution - but I can't. I'm using my laptop now (Windows XP) and it's connecting fine.
I've tried:
- Resetting the router
- Changing the security type from WPA2/TKIP to none
- Updating the driver (In Windows it says it's and Atheros AR938x Wireless Lan Card)
- Update all Windows
What can I do?
Gear:
Router: Netgear CG 2000
iMac 27 (New model 2011 or what it's called. It a year old)
I've read several times that Windows 7 has problems with connection, but the threads are like 2 years old, so someone must have come up with a sollution?
Christian

I've done that.
I've installed Windows 7 with Bootcamp and everything is installed correctly if I look in "Device Manager". There are no problems - except that I cannot join the wireless network.
If I plug a cable in it works fine.

Cannot connect to router E1000

Hello,
I own a E1000 router that I use with several wireless machines. I have no problem connecting to the internet.
Unfortunately, I cannot connect to the configuration of the router by typing https://192.168.1.1/ nor http://192.168.1.1/ in a browser, be it wirelessly or wiredly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router".
I tried to switch my router off and on, but that doesn't help. Totally resetting the router solves the problem, but not definitely.
Is there a solution that does not require resetting my router?
Thank you very much.

(I don't see anymore how to edit my initial post.)
The message displayed by Firefox is “The connection was reset” and not what I had translated into “Connection has been reinitialized”.
As far as the OSs are concerned, the machines that should be able to access my router are running Ubuntu, Android, Windows and an embed version of Linux. I tried with different webbrowsers, including Firefox and the Android Browser.
Please tell me if I should add any additional information.
I did a lot of search on the web and some say that similar problems come from the option of HTTPS that is selected for accessing the administration page. Is this correct? Should I abandon the idea of wanting a configuration with HTTPS?

Window Server cannot connect to Router?

Similar Messages

Maybe you are looking for