Wireless Adapter Error 10 when CSM Support Disabled

After a motherboard replacement, my Thinkpad Yoga was returned with CSM Support enabled, causing a legacy bios and windows splash screen to appear.
I went into the bios and disabled CSM support to bring back the default black Lenovo boot up screen, but now when windows loads the Wireless Card reports an Error Code 10. I have tried updating to every driver and even refreshed windows to no avail.

I later disabled Broadcom Virtual Wireless Adapter and found that I could still use WiFi so I went on and upgraded to Windows 10 anyway. Broadcom Virtual Wireless Adapter does come off the list on Device Manger but I can still use WiFi regardless.

Similar Messages

  • Wireless 276DW Error notification when printing

    My computer is a ENVY 23 Touchsmart running Windows 8.1 (64-bits). I connect wirelessly to my Officejet Pro 276DW. I have the latest driver (OJ276_DW_90) installed.
    My Word 2013 document has two sections. Section 1 is a six page table of contents. Section 2 consists of 28 pages. I print the document duplex. Part way through the printing I get an error notification stating "error printing on HP OfficeJet Pro 276DW. The printer could not print Microsoft Word -" and then the name of the document. However, the document appears to print correctly.
    I went out to the HP driver and support webpage to ensure that I have the latest driver. On the page was something about subscribing to drivers support alerts which I already do. But it also said, "downloads for this product are not available through this website."
    This question was solved.
    View Solution.

    1. Open the Control Panel.
    2. Click on Devices and Printers.
    3. Right click on the 276dw.
    4. Click on Printer Properties.
    5. Click on the Ports tab.
    6. Click on the Add Port button.
    7. In the Available port types box, select Standard TCP/IP Port.
    8. Click on the New Port button.
    9. Click on the Next button.
    10. In the Printer Name or IP Address box, enter thye correct IP Address.
    11. Click on the Next button.
    12. Click on the OK button. If only one copy of the printer appears in the Device and Printers go to step 22.
    13. Delete both copies of the 276DW printer.
    14. Click on the Add A Printer button.
    15. In the Select a Printer, select the printer with the correct IP Address.
    16. Click on the Next button.
    17. In the Which version of the driver do you want to use, select Use the driver that is currently installed.
    18. Click on the Next button.
    19. Click on the Next button.
    20. In the Printer Sharing, click on the Next button.
    21. Click on the Finish button.
    22. If the printer icon is NOT grayed out, go to step 28.
    23. Right click on the 276DW printer.
    24. Click on See What’s Printing. This will open the Printer Spooler.
    25. Click on the Printer menu.
    26. Uncheck Use Printer Offline.
    27. Close the Printer Spooler.
    28. Done.

  • Loadjava protocol adapter error

    Hello all,
    I am developing a program using Java Stored Procedures with Oracle 9.2.0.1 using an oracle client and am having difficulty with the loadjava utility.
    When attempting to load a class using loadjava I get unresolvable errors no matter what driver I use (thin, oci, oci8). When using the oci or oci8 drivers I get a "protocol adapter" error. When I use the thin driver I get a "null username or password" error even though I specify the username/password in the call.
    These are the messages I am receiving through the DOS command prompt:
    //using OCI8
    P:\>loadjava -v -user username\password HiThere.class
    arguments: '-v' 'user' 'username\password' 'HiThere.class'
    SQL Error while connecting with oci8 driver to default database: ORA-12560: TNS:
    protocol adapter error
    //specifying OCI
    P:\>loadjava -v -user username\password -oci HiThere.class
    arguments: 'v' 'user' 'username\password' 'oci' 'HiThere.class'
    SQL Error while connecting with oci8 driver to default database: ORA-12560: TNS:
    protocol adapter error
    //using thin driver
    P:\>loadjava -v -thin -user username\[email protected]:1521:cnfi HiThere.
    class arguments: '-v' '-thin' '-user' 'username\[email protected]:1521:cnfi' 'H
    iThere.class'
    SQL Error while connecting with thin driver to gaia.nfis.org:1521:cnfi: Null user or password not supported in THIN driver
    exiting : could not open connection
    I can connect to the database using a JDBC connection and the thin driver but have no idea how to get the loadjava command using the thin driver to use the username\password that I provide instead of saying that there cannot be a null username\password.
    Any suggestions on how I can get loadjava to connect to Oracle would be much appreciated.
    Thankyou,
    Matt
    ps: I am also having difficulties using the dbms_java.loadjava utility using SQL*Plus (java.security.AccessControlException) which might be resolved through my DBA.

    Matt,
    This is just a guess, but try using a forward slash ("/") instead of a backslash ("\"), to separate the "username" from the "password", as in:
    loadjava -v -thin -user username/[email protected]:1521:cnfi HiThere.classGood Luck,
    Avi.

  • Disabling Wireless Adapter

    I want to run a Powershell Startup Script to disable the Wireless adapters on some systems. I thought I'd want to get some WMI stuff
    Get-WmiObject -Class Win32_NetworkAdapter -Filter "Name = 'Intel(R) Centrino(R) Advanced-N 6205'
    Then run netsh to disable it
    netsh interface set interface "Wireless Network Connection" DISABLED
    After looking at this I wondered why not just run the
    netsh interface set interface "Wireless Network Connection" DISABLED
    I don't really need the Get-WmiObject do I?
    Orange County District Attorney

    Here are a couple of scripts ( ps and vbscript )  that can be used on a dell bios.. You could adapt it to disable the wireless adapter in the bios if you want  ..
    ( pcombobox app is on www.justcode.ca  )
    Powershell ( may require dell client management agent )
    (gwmi DCIM_BIOSService -namespace root\dcim\sysman).SetBIOSAttributes($null,$null,"Wake On LAN","4")
    Possible values are:
    1 - Disable
    2 - Add-in
    3 - On board
    4 - LAN
    5 - PXE boot enable
    6 - LAN or WLAN
    7 - WLAN only
    vbscript
    '  Set Dell Bios items
    '  Requires that the Dell Client Management software is installed 
    'Dell DCIM values
    ' Wake on LAN values
    'Enables or Disables Multiple CPU Core support on next boot.
    'Possible values are:
    '1 = Other
    '2 = Unsupported
    '3 = Enabled
    '4 = Disabled
    'The actual values are not the above, but the below - Paul Jorgensen - Nov 2011 ( Dell gx760 )
    '1 = Disabled
    '2 = Enabled
    'AC Power Recovery Mode
    '1 = ?
    '2 = ?
    'Processor Logical Processor(HyperThreading)
    '1 = ?
    '2 = ?
    Option Explicit
    '*** Declare variables
    Dim strNameSpace
    Dim strComputerName
    Dim strClassName
    Dim strKeyValue
    Dim objWMIService
    Dim ColSystem
    Dim objInstance
    Dim oInParams
    Dim returnValue
    Dim strAttributeName(2)
    Dim strAttributeValue(2)
    Dim strAuthorizationToken
    Dim psDellBios
    Dim WshShell, objWshScriptExec
    Dim psAttribute
    Dim psValue
    Dim pbAttributeFound
    Set WshShell = WScript.CreateObject("WScript.Shell")
    '*** Check that the right executable was used to run the script
    '*** and that all parameters were passed
    If (LCase(Right(WScript.FullName, 11)) = "wscript.exe" ) Or _
        (WScript.Arguments.Count < 1) Then
        Call Usage()
        WScript.Quit
    End If
    '*** request combobox input as to which bios setting should be updated
    psDellBios = GetComboInput("pcombobox.exe /p:WakeOnLAN,EnableDualCPU")
    WScript.Echo("This is setting ->" & psDellBios)
    '*** Initialize variables
    strNameSpace = "root\dcim\sysman"
    strComputerName = WScript.Arguments(0)
    strClassName = "DCIM_BIOSEnumeration"
    '*** Set Variables based on combobox selection
    If psDellBios = "WakeOnLAN" Then 
    psAttribute = "Wake On LAN"
    psValue = "4"
    End If
    If psDellBios = "EnableDualCPU" Then
    psAttribute = "Multiple CPU Cores"
    psValue = "1"             ' see value notes at top of script
    End If
    '*** Retrieve the instance of DCIM_BIOSEnumeration class for the TPM
    Set objInstance = GetObject("WinMgmts:{impersonationLevel=impersonate," &_
        "AuthenticationLevel=pktprivacy}\\" & strComputerName & "\" &_
    strNameSpace)
    '*** print out attribute if found
    Set ColSystem = objInstance.execquery("Select * from " & strClassName)
    For Each objInstance In ColSystem
    '*** Check every instance
      'iTKVal = objInstance.Properties_.Item("CurrentValue").Value(0)
    '*** Auto On Hour and Auto On Minutes don't have PossibleValues and PossibleValuesDescription properties
    If (objInstance.AttributeName = psAttribute)  Then
    WScript.Echo("Specified Attribute found " & objInstance.AttributeName & ", " & ( objInstance.CurrentValue(0) ) & VbCrLf )
    pbAttributeFound = True
    End If
    Next
        strClassName = "DCIM_BIOSService"
        strAttributeName(0) = psAttribute    ' Wake on LAn or Multi Core CPU, see psAttribute in query section above
    WScript.Echo("strAttributeName-> " & strAttributeName(0))
      strAttributeValue(0) = psValue
        WScript.Echo("strValue-> " & strAttributeValue(0))
        strAuthorizationToken = ""
        '*** Retrieve the instance of DCIM_BIOSService class 
    Set objWMIService = GetObject("WinMgmts:{impersonationLevel=impersonate," &_
            "AuthenticationLevel=pktprivacy}\\" & strComputerName & "\" &_
    strNameSpace )
        Set ColSystem=objWMIService.execquery ("Select * from " & strClassName)
        For Each objInstance In ColSystem    
            Set oInParams = objInstance.Methods_("SetBIOSAttributes").InParameters.SpawnInstance_
            oInParams.AttributeName = strAttributeName
            oInParams.AttributeValue = strAttributeValue
            oInParams.AuthorizationToken = strAuthorizationToken
            Set returnValue = objInstance.ExecMethod_("SetBIOSAttributes", oInParams)
            Exit For
        Next
    'End If
    '*** If any errors occurred, let the user know
    If Err.Number <> 0 Then
        WScript.Echo "Enabling Wake On LAN failed."
    End If
    '*** Sub used to display the correct usage of the script
    Sub Usage()
    Dim strMessage
    strMessage = "incorrect syntax. You should run: " & vbCRLF & _
        "cscript.exe /nologo SampleWakeOnLAN.vbs <systemname>"
    WScript.Echo strMessage
    End Sub
    Function GetComboInput(cbparam)
    Dim sTempPath, sTempResult, sTempExitCode
    sTempPath = cbparam
    WScript.Echo sTempPath
    Err.Clear
    'WshShell.run sTempPath, WINDOWNORMAL, True
    Set objWshScriptExec = WshShell.Exec(sTempPath)
    ' ***** BELOW - **  USE RegRead to read reg return value **** !!!!
    'wscript.Echo WshShell.RegRead(testregpath)
    'WScript.Echo Err.Number
    Do While objWshScriptExec.Status = 0
    WScript.Sleep 100
    'WScript.Echo "this is the status code" & objWshScriptExec.Status
    Loop
    '**** if item was not picked from combobox, take action based on errorlevel
    sTempExitCode = objWshScriptExec.ExitCode
    If (objWshScriptExec.ExitCode = 0 Or objWshScriptExec.ExitCode = 100 Or objWshScriptExec.ExitCode = 102 Or objWshScriptExec.ExitCode = 101) Then
    'If(objWshScriptExec.ExitCode > 20 )Then 
    Select Case sTempExitCode
    Case 0
    WScript.Echo "User clicked cancel"
    WScript.Quit(0)
    Exit Function
    Case 100   
    WScript.Echo "User clicked return abort"
    WScript.Quit(100)
    Exit Function
    Case 101
    WScript.Echo "User clicked ok with NULL item"
    WScript.Quit(101)
    Exit Function
    Case 102
    WScript.Echo "User clicked ok with data entry"
    'WScript.Echo " result is " & 
    GetComboInput = WshShell.RegRead("HKCU\Software\Green-Frog-Software\pComboBox\RData\PComboBox")
    WScript.Echo " GetComboInput is " & GetComboInput
    Exit Function
    Case Else
    End Select  
    End If
    'WScript.Echo objWshScriptExec.ExitCode
    '**** return the error value
    '*****ACTUALLY - parse "cbparam" using the exitcode to return the 
    '***** the string required rather then run another function
    '***** or run a generic function from here...
    '***** this will make the function single line usage 
    '***** which is way more script friendly
    sTempResult = pfParseResult(cbparam, objWshScriptExec.ExitCode)
    'WScript.Echo sTempResult
    GetComboInput = sTempResult
    End Function
    ' ** Application:  VB MapDrives
    ' ** Function:  pfParseResult
    ' ** Purpose:   match the errorlevel returned to the input string desired
    ' ** Update:    
    ' ** Date: Jan 6 2009
    ' ** Author:    Paul Jorgensen
    Function pfParseResult(cbparam, pi_Result)
    Dim sTempPath, sSplitFirst, piLen
    Dim paParseArray
    sTempPath = cbparam
    'WScript.Echo sTempPath
    Err.Clear
    piLen = Len(cbparam)
    If (piLen > 17) Then
    sSplitFirst = Right(cbparam, piLen - 17)    ' 17 = 3 for /p: and 14 for pcombobox.exe with spaces
    End If
    'WScript.Echo "this is sSplitFirst" & sSplitFirst
    paParseArray = Split(sSplitFirst, ",", -1, 0)     ' string, delimiter, count -1 = all, binary(0) or text (1)
    'WScript.echo CrLf
    'WScript.echo paParseArray(0)
    'WScript.echo CrLf
    'WScript.echo paParseArray(1)
    ' ie a valid selection was returned from GetComboInput, so use the return code ( pi_Result) which represents the item
    ' selected to select the item from the paParseArray which is the cbparam parameter minus the exe and the /p: with
    ' the /p: parameters split into the paParseArray ( ie D,L,R,S,V.... )
    pfParseResult = paParseArray(pi_Result - 1)
    'Do While objWshScriptExec.Status =0
    'WScript.Sleep 100
    'WScript.Echo "this is the status code" & objWshScriptExec.Status
    'Loop
    End Function
    just code, no beer...although that would probably help..

  • I updated itunes to 10.4, my ipod touch was wiped clean then errored (2003) when attempting to restore, now my ipod is clear. I have tried disabling my antivirus, no luck.

    I updated itunes to 10.4, my ipod touch was wiped clean then errored (2003) when attempting to restore. Now my ipod is clear, when I turn it on I get the "Connect to itunes screen", this never goes. I have tried disabling my antivirus, to allow me to restore with no luck.
    When I go into itunes I get the message - itunes has detected an ipod in recovery mode. You must restore this ipod before it can be used with itunes,
    how am I supposed to do this ?
    I would rather take the ipod to someone to do the restoration - I still have itunes with all of my downloads on my computer, I dont want to risk losing this as I can re-install onto my ipod when it is sorted.

    Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on): If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software.
    Above from:
    http://support.apple.com/kb/TS3694
    It may be more than you security software.
    Do you have access to another computer you can use to restore the iPod to factory defaults/new iPod?

  • WRT160N Router Error message when connecting wireless

    This is the advanced error report I received after diagnosing my connection. Everything I have tried to do has not solved my problem. Please Help! Thanks
    Helper Class (RNWF MSM Helper Class) Event:
    Wireless Diagnostic Helper Class Event
    For complete information about this session see the Wireless Diagnostic Informational Event.
    Helper Class: Native WiFi MSM
     Initialize status: Success
    Information for connection being diagnosed
     Interface GUID: 0c5fedf8-83c2-45eb-a664-bc2385294b58
     Interface name: Intel(R) Wireless WiFi Link 4965AGN
     Interface type: Native WiFi
     Profile: DaveJeremyCameronBen
     SSID: DaveJeremyCameronBen
     SSID length: 20
     Connection mode: Infra
     Security: Yes
     Connect even if network is not broadcasting: No
    Result of diagnosis: Problem found
    Root cause:
    The wireless settings for the network adapter on this computer don't match the settings of "DaveJeremyCameronBen"
    The selected data rate is not correct.
    Detailed root cause:
    802.11 connection failed due to status code 18: Association denied due to requesting station not supporting all of the data rates in the BSSBasicRateSet parameter
    Repair option:
    View the wireless network adapter settings on this computer to verify they are compatible with this network
    If you set up or own this network, you might be able to fix the problem by changing the settings on the wireless router or access point to be compatible with the settings on this computer. Contact the network administrator for "DaveJeremyCameronBen" or your hardware manufacturer for further assistance.
    Event Verbosity:0
    Solved!
    Go to Solution.

    I think there is a profile saved on your wireless computer.
    What is the operating system on your computer ?
    Delete the profile on your wireless computer. I think you are using the intel wireless adapter on that computer.
    Open the Intel wireless adapter utility. There you will find the profiles saved on your computer. Delete the wireless network profile that you are trying to connect.
    Now open the setup page of the wireles router. Go to the wireless tab. Check the wireless network name. Click on wireless security tab and check the wireless security settings. Make sure that you have the correct network key/password.
    Now try to connect to the wireless network again.
    If it is windows XP operating system then you can also connect to the wireless network using the windows wireless network utility.

  • Error in SAP console - SapSSLInit failed = https support disabled

    Hi,
    I am using windows 2003 server when logged in to start the SAP console i have the below error. Please note, i have only a user level of knowledge so please help me with the resolution with a clear steps. Thanks in advance for your help
    Startup Profile: "C:\usr\sap\SB2\SYS\profile\START_DVEBMGS20_SABSB2"
    Starting Programs
    (2292) Execute: C:\usr\sap\SB2\SYS\exe\uc\NTI386\sapcpe.EXE pf=C:\usr\sap\SB2\SYS\profile\SB2_DVEBMGS20_SABSB2
    (2336) Execute: C:\usr\sap\SB2\SYS\exe\uc\NTI386\strdbs.cmd SB2
    (2512) CreateProcess: C:\usr\sap\SB2\DVEBMGS20\exe\msg_server.EXE pf=C:\usr\sap\SB2\SYS\profile\SB2_DVEBMGS20_SABSB2
    (2520) CreateProcess: C:\usr\sap\SB2\DVEBMGS20\exe\disp+work.EXE pf=C:\usr\sap\SB2\SYS\profile\SB2_DVEBMGS20_SABSB2
    (2528) CreateProcess: C:\usr\sap\SB2\DVEBMGS20\exe\igswd.EXE -mode=profile pf=C:\usr\sap\SB2\SYS\profile\SB2_DVEBMGS20_SABSB2
    Starting WebService thread
    SapSSLInit failed => https support disabled
    Webservice thread started, listening on port 52013
    Webservice named pipe thread started, listening on port
    .\pipe\sapcontrol_20

    Hello,
    Please activate SSL on the Portal again as per online help:
    http://help.sap.com/saphelp_nw04s/helpdata/de/f1/2de3be0382df45a398d3f9f
    b86a36a/frameset.htm
    The portal should be reachable via https after performing the
    steps.
    regards,
    John Feely

  • Gives  ORA-12560: TNS: protocol adapter error when installing oracle 10g

    I tried to install oracle 10g r2 in server 2008. but it gives ORA-12560: TNS: protocol adapter error when installing. how I can fix this issue??? please help me ASAP. because its urgent.
    thanks in advance.
    chamara

    Welcome to the forums !
    Pl indicate which version of 10g you are installing and on which version of Win 2008. Neither 10gR1 nor 10gR2 are certified to be installed on Win 2008 R1, AFAIK.
    For 10gR2, only 10.2.0.5 is certified for Win 2008 R2 - see MOS Doc 1173433.1 (How to Install Oracle 10.2.0.5 on MS Windows 7 / Windows 2008R2)
    Also see MOS Doc 740926.1 (Where can I find the Database / Client software to download for Microsoft Vista, or Windows 2008R1?).
    Both 10gR1 and 10gR2 are now in extended support - is there a reason you are not using 11gR2 ?
    HTH
    Srini

  • TNS-12560: TNS:protocol adapter error when starting listner

    Hi,
    I am having this error when trying to start my oracle database listener.
    I can connect to database normally with SqlPlus
    Microsoft Loopback Adapter is installed and config with a fixed IP address. The IP add with computer name and domain is specified in the hosts file.
    I didn't modify anything to the default listener.ora file.
    Any suggestion. Thank you very much.
    Best regards
    K.

    Now I am able to start my listener after I turn off my firewall and restart my computer. The port might be blocked previously ?
    However, now I can't connect to the database even in Sql plus. When connect using user name and password, I have the same error: TNS-12560: TNS:protocol adapter error.
    Testing my connection in Net CA, it said: "TNS:listener does not currently know of service requested in connect descriptor".
    In tnsnames.ora, I have SERVICE_NAME= orcl.
    Result of tnsping orcl is "..OK<100msec>"
    But result of lsnrctl services is: "The listnener supports no services"
    I can't find any clue?
    P/S: I am using Oracle database 11g EE Release 11.1.0.7.0 on Window platform.
    Edited by: user12635456 on 13-Jun-2010 20:42

  • Wireless Adapter permanently disabled after sleep mode - Windows 7 64 bit

    Hello,
    Info:
    Laptop: 2014 Macbook Pro running Bootcamp (dual boot...not a VM) with Windows 7 Pro 64 bit
    OS: Windows 7 Pro 64 bit
    Network Adapter: Broadcom 802.11ac Network Adapter
    Driver version: 6.30.223.215
    Issue: My broadcom 802.11ac wireless adapter becomes permanently disabled when waking from sleep mode. It requires a restart in order to become enabled. If I try to manually re-enable it, I get a message saying "Enabling..." -> "Enabled!" but after this message the device still says Disabled and the wireless still won't connect to anything. This issue is very reproducible. Occurs both under battery power and when plugged in.
    What have I tried?: Tried disabling the "Allow windows to disable this device to save power" under power management, which didn't work. Tried updating driver but Windows Update says the driver is up to date. I was able to find a newer version (6.30.223.227) but I can only find it hosted on Russian websites which makes me a little suspicious.

    Many thanks to chemnerd1's hints - saved me going mad.
    My problem was that the wifi worked perfectly until connected to a Thunderbolt display - then the wifi was permanently disabled (nothing would enable it; changing driver, changing wifi channel, uninstalling and reinstalling wifi, nothing worked). As you can imagine I was very disapointed after spending a fortune on the Thunderbolt display (brilliant kit) and then finding that I maybe only have wired internet available!
    Definately, Zone Alarm was the problem (maybe other firewalls cause the same /similar problem).
    My solution was -
    uninstalled Zone Alarm (safe mode not required)
    reboot with Thunderbolt display connected (checked that wifi now working)
    reinstall Zone Alarm (important that Thunderbolt display is still connected)
    reboot - checked and wifi still working perfectly - wonderful
    I have to confess that I was initially blaming Apple for the problem. I did loads of searches to try and solve this and a lot of links ended with conclusions that Apple doesn't care. Well in this case it wasn't Apple's fault.

  • Following error occurring when running application in wireless tool kit

    Hi
    Following error occurring when running application in wireless tool kit
    java/lang/ClassFormatError: Bad version information.
    can any suggest y ?

    Hi,
    I am also facing the same problem......................
    java/lang/ClassFormatError: Bad version information
    The error occurs when I try to simulate the mobile device using wireless tool kit. Does it have anything to do with the antivirus/firewall running on my system?
    Did Ram get a solution to his problem? Can anybody please help?
    Many Thanks
    Merin
    HI
    Sorry i could not find any related information there
    the version of wireless toolkit i am using is 2.1
    well in release notes its given that it also
    supports cldc1.0 and midp1.0
    presently i am using cldc1.0.4 and midp1.0.3
    versions
    is there any version compatability error
    please suggest me its quite urgent

  • Error message when installing iTunes on Windows 7, "Apple Application Support was not found, Error 2"

    I can successfully download iTunes on my PC, but receive an error message when I try to install the file: "Apple Application Support was not found... Error 2" I've tried deleting the file and reinstalling it to no avail. Any ideas?

    See Troubleshooting issues with iTunes for Windows updates.
    tt2

  • I keep getting the following error message when I try to update my itunes, "There is a problem with this windows installer package. Aprogram run as part of the set up did not finish as expected.  Contact your support personnel or package vendor."

    I keep getting the following error message when I try to update my itunes, "There is a problem with this windows installer package. Aprogram run as part of the set up did not finish as expected.  Contact your support personnel or package vendor."

    Yes, I had found a similar solution also.  I'm running XP Pro, SP3.  I went Control Panels/ Add-Remove programmes/apple software update/ change/ repair.  Then run the 10.5 exe.
    While the programme updated from version 8 of iTunes, my new iTunes is now a mess.  Not all of my music was in the same folder previously but it all showed up on iTunes.  Now many albums have been left out, some have only a few tracks and some have two copies of some tracks as well as having other tracks missing.  I haven't begun to work on that.

  • I get an error message when trying to sign into the support community with another Apple id. On the pick a username screen I get "an account utilizing this address already exists...." despite trying a few usernames. Anyone know how I can resolve this?

    I get an error message when trying to sign into the support community with another Apple id. On the <pick a username> screen I get "an account utilizing this address already exists.Only one account per email address is allowed on the Apple Support Communities" despite trying a few usernames. Anyone know how I can resolve this?

    This problem has been driving me demented. The instructions that Ivan gives have partially worked for me. By following his link
    "How to find out if you have multiple Apple IDs" I was able to identify that yes I did have two apple accounts using the same e mail address. One was very old that I used to use for the forum boards and one is my much more recent ID that I use for everything these days. So I changed the e mail address for the old account which is associated with these discussion boards and that's the account that I am now posting this from. However even though the two accounts now have different e mail addresses when I try to log onto the boards with my more recent main apple ID I still get all the same errors as described at the start of this thread by rodgers_j. And of course that's the one I want to use so that I only have one itunes account for everything.
    So if anyone has any more hints I'd be very grateful.

  • Error message when trying to add signature. An error has occurred that may be fixed by installing the latest version of the Japanese Language Support package.

    Error message when trying to add signature. An error has occurred that may be fixed by installing the latest version of the Japanese Language Support package.  How can I fix this?
    Thanks
    [email protected]

    What is your operating system?  Reader version?

Maybe you are looking for