Work Group Bridge

I have a cisco AIR-CAP3602E-EK9 and I want to configure it as WGB, I am trying to run dot11 ssid command to conifgure SSID but its not working. Can anybody tell me the command reference to configure AIR-CAP3602E-EK9 as WGB?

Do you have autonomous image on your 3602 ? If not you have to convert Lightweigh image to Autonomous using one of the below methods before configuring it as WGB.
http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/
Then you can configure WGB like below.
http://mrncciew.com/2013/07/02/wgb-config-example/
HTH
Rasika
**** Pls rate all useful responses ****

Similar Messages

Work group bridge with cisco 3500

Hi,
We have few cisco 3500 ap's which is to be used as work group bridge. I am not very sure but i think we need the ap to be in autonomous mode to make it a work group bridge. Currently it is running lwapp/capwap image.
Is this correct, please help with suggestions.

sh ip int brie
Interface                  IP-Address      OK? Method Status                Prot
ocol
BVI1                       10.82.6.247     YES DHCP   up                    up
Dot11Radio0                unassigned      NO unset up                    up
Dot11Radio1                unassigned      NO unset up                    up
GigabitEthernet0           192.168.1.2     YES manual up                    up
AP-OF#sh ver
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA7, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 29-Jan-13 05:19 by prod_rel_team
ROM: Bootstrap program is C3500 boot loader
BOOTLDR: C3500 Boot Loader (AP3G1-BOOT-M), Version 12.4 [mpleso-ap_jmr3_esc_0514
116]
AP_OF uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g1-k9w8-mx.124-23c.JA7/ap3g1-k9w8-xx.124-23c.JA7
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3502E-S-K9    (PowerPC460exr) processor (revision B0) with 81910K/4
9152K bytes of memory.
Processor board ID FGL1721S5G0
PowerPC460exr CPU at 666Mhz, revision number 0x18A8
Last reset from power-on
LWAPP image version 7.0.240.0
1 Gigabit Ethernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: BC:16:65:77:D9:93
Part Number                          : 73-12175-06
PCA Assembly Number                  : 800-32268-06
PCA Revision Number                  : B0
PCB Serial Number                    : FOC171622Y6
Top Assembly Part Number             : 800-32904-02
Top Assembly Serial Number           : FGL1721S5G0
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP3502E-S-K9
Configuration register is 0xF
sh run | i def
aaa authentication login default local
ip default-gateway 192.168.1.55

Cisco AP 700w as a Work Group Bridge with a WLAN Controller

I am trying to setup an AP 700w as a Work Group Bridge as it would be interesting to have this running, because it has the built-in 4 port switch.
I have WiSM based WLCs running the version 7.0.240.0. I converted a 700w to an autonomous AP and on the AP I installed the IOS Version 15.3(3)JA1.
When I use an autonmous based AP to connect the 700w as a WGB everything works fine. I can connect clients through the 4 port switch.
If I try to use a Controller based WLAN environment it does not work. The config is simple:
ap#sh run
Building configuration...
Current configuration : 1805 bytes
! Last configuration change at 18:37:11 UTC Thu Mar 5 2015
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
logging rate-limit console 9
enable secret 5 $1$b5Da$QTI6Geq7ARZud34ZqA45.0
no aaa new-model
led display off
no ip source-route
no ip cef
dot11 syslog
dot11 ssid LAGERWPA
   authentication open
   authentication key-management wpa
   wpa-psk ascii 7 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
username CISCO password 7 14341B180F0B
bridge irb
interface Dot11Radio0
no ip address
encryption mode ciphers aes-ccm tkip
ssid LAGERWPA
antenna gain 0
packet retries 64 drop-packet
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
shutdown
antenna gain 0
peakdetect
no dfs band block
packet retries 64 drop-packet
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
mac-address 18e7.2801.9610
ip address dhcp client-id GigabitEthernet0
ipv6 address dhcp
ipv6 address autoconfig
ipv6 enable
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
lan-port port-id 1
no shutdown
lan-port port-id 2
shutdown
lan-port port-id 3
shutdown
lan-port port-id 4
shutdown
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end
The association is OK, it is seen as a WGB, I can reach resources on our network from the AP, ping works, I can use a telnet from client to access the AP 700w etc.:

20... Here is an old post for reference.
https://supportforums.cisco.com/thread/2119996
Sent from Cisco Technical Support iPhone App

Work Group Bridge - Which Mode to Use?

We have some rolling carts used for telemedicine and are currently using Linksys WET610N wireless bridges. I haven't been very impressed with them - I have to reboot them at least once a week and figure it's a roaming issue. Since they are a residential product they probably weren't designed to do a lot of roaming.
I started playing around with WGB and setup an 1142 AP and got it to work. Unfortunately, the only place I can put the AP is inside the cart and the metal top seems to be interfering with the wireless signal.
Which Cisco indoor APs have external antennae mounts and are capable of performing as a WGB?
Our infrastructure is 4400 controllers and 1142 APs.
Thanks.

Look at the 1242's to use as WGB.
Sent from Cisco Technical Support iPhone App

How many clients on etehrnet lan when config as work-group bridge?

I am considering configuring a 1242ag as either a WGB / non-root bridge, I have read that a WGB can have only 8 clients on its ethernet lan side, and does not associate with wireless clients other then the root-bridge/AP. Can someone confirm this for me?

WGB acts only in Non-Root Bridge w/o clients mode.It is right that Workgroup bridge can accosiate to either Root AP or Root Bridge.

Problem with work group bridge authentication with ACS 5.x

EAP-TLS authentication for workgoup brdige fails.
Folloing is the log on ACS
Authentication failed 12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in the client certificates chain
12811 Extracted TLS Certificate message containing client certificate.
12814 Prepared TLS Alert message.12817 TLS handshake failed.
12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in the client certificates chain
12507 EAP-TLS authentication failed12505 Prepared EAP-Request with another EAP-TLS challenge
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12504 Extracted EAP-Response containing EAP-TLS challenge-response
11504 Prepared EAP-Failure11003 Returned RADIUS Access-Reject

I have seen this issue before, the AP is present an old PAC and doesnt update until after you reboot. You can open a wireless TAC case and they will get you the right image as to when this was fixed. As a workaround you can extend the lifetime of the PAC in your authentication settings for EAP-FAST.
Thanks,
Sent from Cisco Technical Support iPad App

I can't get Dr Browns Image Processor Pro to work from Bridge with Photoshop CC 2014

We use the wonderful DR Browns Image Processor Pro script a lot, but cannot get it to work from Bridge with PS CC 2014. When I select files in Bridge CC and then go to Tools> Dr Browns Services 2.3.1 > Image Processor Pro it just pops up an error message that says ReferenceError: photoshop is undefined.
The actual script works fine if I launch it from Photoshop CC 2014 - just not if I load it from Bridge CC.
I have unistalled it and re installed a few times, both manually and through the Extension Manager CC.
I am using a Win 7 64bit computer.
I assume there is some change in the scripting part that loads Photoshop from bridge but not sure. It worked fine in CC. Just not CC 2014.
I opened the Dr Browns Services .jsx file but don't see anything obvious. This is the section related to the Image Processor Pro part:
// This routine takes an array of files. If called by Photoshop,
// it will invoke Dr. Brown's Process 1-2-3 with the files. If called by
// any other app, it will send a BridgeTalk message to Photoshop
// to invoke this routine with the same arguments.
drbrownserv.process123 = function (files) {
// Bring Photoshop to the foreground.
BridgeTalk.bringToFront ("photoshop");
// Create a new BridgeTalk message for Photoshop to invoke
// Image Processor with the selected files
var btMessage = new BridgeTalk;
btMessage.target = "photoshop";
btMessage.body = "drbrownserv.process123 (" + files.toSource () + ");";
btMessage.send ();
} else {
photoshop.runActionCommand ('611736f0-9c46-11e0-aa82-0800200c9a66', files);
catch (error) {
if (error.number != 8007) // Don't report user cancelled errors.
drbrownserv.alert (error);

I copied that .jsx file to a new name "Xbytor Image Processor Pro.jsx" edit that file changed the string Dr Browns services to "Xbytor Image Processor Pro" then commented out all the code that added tools menu items but "Image Processor Pro" and I put that file into
"C:\Program Files (x86)\Common Files\Adobe\Startup Scripts CC\Adobe Bridge" even though Bridge CC is 64Bit seems to use theat location.
Bridge CC was updated by the creative clouds update and opens Photoshop CC 2014 now

Scroll not working in Bridge 5

Is there some setting that I have to tickle to get the scroll on my mouse to work in Bridge 5? It does fine in Photoshop 5. Thanks, Bernie

Hi,
I'm running the following:
Adobe master CS5
Windows 7 64bit
Logitech keyboard MX5000
Logitech Performance MX mouse
The setpoint software version 6.2 that came with the Performance MX mouse would make CS5 bridge not scroll as described. I uninstalled setpoint 6.2 x64 and installed setpoint 4.8 x64, which is the most current driver for the MX5000 keyboard. Evereything is working now...

Hello, Mouse scroll stop to work in BRIDGE CC

Hello, Mouse scroll stop to work in BRIDGE CC, and I have lots of troubles with this one like he didn't know how to open AI file or TIFF ...(fix that but not the scroll)

Windows 7 64bits, drivers is updated and all work fine in all other softwares or OS
Originally that work on BRIDGE but that stop and I try to unistall them, install another time or adjust things but nothing change

Photoshop Elements 11 and Metadata Working Group Guidelines

Could you please let me know whether Adobe Photoshop Elements 11 is fully compliant or not with Metadata Working Group Guidelines?
Thank you

PSE11 supports the IPTC data fields but captions (description) and keywords are stored in the catalog unless metadata is written to files. GPS co-ordinates written by a digital camera or device can also be read by PSE11.
http://www.adobe.com/products/xmp/

How to get Camera Raw 6.7 to work in Bridge CS5?

I've read past posts about the ways to fix this problem, but they don't work for me. I'm using a pc with windows 8.1. I've downloaded and installed Camera Raw 6.7 update and when I select "Help, Update" in Bridge, it says I have the latest updates installed..

In what way is ACR not working in Bridge? Is there no right-click Open in Camera Raw available from Bridge, or there is, but the ACR version is less than ACR 6.7.1 or what exactly is the issue?
Also, if you open Photoshop and do Help / About Plug-ins / Camera Raw, is ACR missing from the list, or if not, what version does it say is installed?
You might also want to describe what methods you have tried to correct the issue, since saying you've tried what you've seen posted and they didn't work, isn't really much to go on.

My ip address is not seen by other computers in my work group

Mac Mini OS X.10.2, 2.3 GHz i5, 8 GB 1333 DDR3, 500 gb hd
I can not ping my Mac from other computers in my work group (both PC and Mac). I've been sharing a folder for a few years in a small work group and all of a sudden that folder can no longer be seen or mounted mounted on other computers in my workgroup. I am connected to the network and internet and I can ping other computers in my group. They can't ping me (get no response when pinging my ip address) and therefore are unable to see me to mount and share my folder.
I've double checked all my sharing setting, permissions and find everthing as it should be, but others are unable to mount my folder.
Thanks in advance for your input.

Airdrop Requirements and some Troubleshooting

Can't get my TC to work in Bridge mode...

I installed Time Capsule TC to my exsisting network, that has a Linksys router. Can't get my TC to work in Bridge mode. Suggestions?
I have the TC directly connected to the router and want to use the TC for wireless Time Machine back ups and to share other hardrives via
the network. I also have an old airport express for airplay speakers in one room. And an airport extreme that I thought I had set up to extend
the network wirelessly. I have yet to find a concise and clear list of steps to make this happen.
Any help would be appreciated.
Holly

The problem is the steps changed with the new airport utility..
I can tell you the steps on a 5.x utility. If you run Lion then download the real tool.
http://support.apple.com/kb/DL1482
Go to manual setup.. internet tab.. connection sharing.. select off, bridge mode.. update the TC..
Wasn't too hard was it.

Work Group Manager Reports and Logs

Mac Manager maintains logs and display current activity information somewhat different that Work Group Manager. With Mac Manager we are able to quickly report for Activity Log, Disk Usage, Connected Machines, Printer Quotas, Workgroup by User, Computers, Checked Out Computers and user activity.
How can we duplicate such a report with Work Group Manager?
We are a school district that is 88% Macintosh and miss the reports and logs feature in Mac Manager (10.3.9).
Hope to hear and find a solution to this challenge.
Marco Baeza, Director of Technology

Hello,
Possibly some ideas here. http://www.macintouch.com/macmanager.html
Carolyn

Command line equivalent of Work Group Manager's export feature

Hello everyone,
I am have a hard time upgrading from Lion Server to Mountain Lion Server, especially with Open Directory. What I wish to do, is to import the existing users and groups of an existing server running Lion Server into a new (fresh) Open Directory master created on another server that is running Mountain Lion Server.
I have tried several options. Those that did *not* work for me include:
Trying to make create a replica of the Lion Open Directory on the Mountain Lion Server
Trying to backup the OD of the Lion Server using slapconfig
What seems to work (for the moment), is to use the export feature of Work Group manager on Lion and to import the users/groups using the import feature of Mountain Lion Server app.
My question is: is there a command line way to do the export ? Since Work Group manager seems to be kind of deprecated in ML, I assume there must be some other way (i.e., from the command line) to do the user/group import and export.
Thanks for your help !

Notice that the old Archive and Restore options are gone. To run a backup, run the slapconfig command along with the -backupdb option followed by a path to a folder to back the data up to:
sudo slapconfig -backupdb /odbackups
To restore a database (such as from a previous version of the operating system where such an important option was actually present) use the following command (which just swaps backupdb with -restoredb)
sudo slapconfig -restoredb /odbackups
/usr/sbin/ServerBackup -cmd backup -source /

Work Group Bridge

Similar Messages

Maybe you are looking for