WRVS4400N VLAN support
Hi all,
I recently purchased a WRVS4400N for my small lab network. I have a question in regards to how the VLANing works on this device.
My objective is to create 4 VLAN's
This is how I want my addressing to look like
VLAN 1 (Servers), Subnet: 172.16.0.0 /26, Gateway: 172.16.0.62
VLAN 2 (IT), Subnet: 172.16.0.64 /26, Gateway: 172.16.0.126
VLAN 3 (Marketing), Subnet: 172.16.0.128 /26, Gateway: 172.16.0.190
VLAN 4 (Design), Subnet: 172.16.0.192 /26, Gateway: 172.16.0.254
I wanted to know if this is possible on the WRVS4400N. Going through the router setup I do NOT see an option where I can assign an IP address range per VLAN. The only DHCP options I see is when I go iunto the LAN settings under Setup. It seems that I can only assign a spefific address range per subnet not by each virtual lan.
If anybody knows how to do this any help would be greatly appriciated!
Cheers
Graham R
The demo ui for the routers on the link you have mentioned are already outdated. Although the RVS4000 ui looks similar to that of WRVS4000N, there are still some features that are yet to be found on the latter.
On the RVS4000 Firmware v1.1.09 Release Notes, one of its features included:
*DHCP Server (in the Setup->LAN page) supports multiple subnets, once multiple VLANs are created.
I have not yet tried to configure vlan on an RVS4000 router since I do not have one, unfortunately . At the moment I am using an RV042.
Similar Messages
-
WRVS4400N VLAN trunking question
Hi all,
I just got a SRW224G4 today my main objective is to trunk 30 VLAN(s) to my WRVS4400N for interVLAN communication. So far I set G1 on my SRW as a trunk port and linked it to port 2 on my WRVS4400N (which is also set as a trunk).
So far no good when I go into LAN settings I do not see an option wheree I can set DHCP addresses or gateways for these VLAN(s). Is this even possible with the WRVS4400N I meen if Linksys is going to provide a small business solution atleast their equipment should support VLAN trunking with each other.
If anybody knows the solution to this please let me know.
CheersFrom what I know, although the WRVS4400N has support for port based VLAN setup, it does not give you the option to set different DHCP addresses for each of the 4 VLANS.
-
On what vlan, if any, is the wireless port configured? I can assign vlan 1-4 to any LAN (hardwired) port to isolate traffic, but not the wireless port. Do wireless packets go to vlan 1 by default and no other vlan #'s? I want to keep wireless traffic out of specific or all LAN ports, yet allow wireless access to the WAN port. Also, how is external VPN traffic routed if vlan is used? To what vlan is the VPN connection assigned? Kan't find any help in the documentation or on the web. The ability to isolate traffic is one of the main reasons for purchasing this product. THX
From what I know, although the WRVS4400N has support for port based VLAN setup, it does not give you the option to set different DHCP addresses for each of the 4 VLANS.
-
I recently bought an 851 only to find out afterwards that it only supports 1 VLAN when I needed it to support at least 7. The documentation on VLAN support seemed pretty buried.
Does anyone know if there is an easy way to find out how many VLANs each router model supports? I dont' want to make the same mistake again, and I can't seem to find what I'm looking for by combing through the data sheets for each model.
Thanks!
Sorry, I meant to post this in the routing and switching forum and I can't figure out how to delete the thread.Hi
A maximum of four VLANs are supported on the Cisco 870 Series with the plus feature set (Advanced IP Services/Advanced Enterprise Services) Cisco IOS. The Cisco 850 Series only supports one 802.1q VLAN.
See this link http://www.cisco.com/en/US/products/hw/routers/ps380/products_qanda_item0900aecd8028a982.shtml -
[Q]: OracleVM VLAN Support with same subnets
Can I create OracleVM Network VLAN pool that would allow for two vlans to use the same network topology or segment. Meaning, does the VLAN know how to tag the vlan I created to know which vlan the traffic came from and route back to the proper vlan. For example, VLAN1 - 192.168.1.0 and have any machines assigned to this vlan to only communicate with other machines on VLAN1. And have VLAN2 on the same network defined private segment with 192.168.1.0 network. BUT, is OVM aware of the tagging of VLAN1 and to route information back to the proper VLAN?
TIAVLAN tagging is independant - and of course must be, since it belongs to layer 2 of the OSI model, of the IP network that is run on it. You musn't confuse the network switches PVID (aka untagged VLAN support) which tagg an incoming packet on a switch port to a specific VLAN.
If you configure VLANs in OVM your're absolutely free to use whatever ip network you want on it - the traffic will stay seperated, since your're running it on a - although virtual - separate LAN. -
Hi,
I've hacked vlan support into the arch init, at least, I haven't been able to test this really, I have no vlan capable switch... This might be of use to some people, or may not... (it also includes my bonding support)
/etc/rc.d/network:
#!/bin/bash
. /etc/rc.conf
. /etc/rc.d/functions
ifup()
varname="$${1}"
eval new_ifline=$varname
vlanname="$${1}_vlan"
eval new_vlline=$vlanname
if [[ $1 != bond[0-9]*_slaves ]]; then
# its a normal interface
if [ "$new_ifline" = "dhcp" ]; then
# remove the .pid file if it exists
rm -f /etc/dhcpc/dhcpcd-${1}.{pid,cache} >/dev/null 2>&1
/usr/sbin/dhcpcd -t 10 -h $HOSTNAME $1
else
/sbin/ifconfig $1 $new_ifline up
fi
if [ "$new_vlline" != "" ]; then
vconfig add $1 $new_vlline
fi
else
# its a bonding interface
for slave_if in ${new_ifline[@]}; do
if echo $slave_if | grep '^[^!]' >/dev/null 2>&1; then
/sbin/ifenslave ${1/_slaves} $slave_if
fi
done
fi
return $?
ifdown()
varname="$${1}"
eval new_ifline=$varname
if [[ $1 != bond[0-9]*_slaves ]]; then
if [ "$new_ifline" = "dhcp" ]; then
[ -f /etc/dhcpc/dhcpcd-${1}.pid ] &&
/bin/kill `cat /etc/dhcpc/dhcpcd-${1}.pid`
else
/sbin/ifconfig $1 $new_ifline down
fi
fi
return $?
rtup()
varname="$${1}"
eval new_rtline=$varname
/sbin/route add $new_rtline
return $?
rtdown()
varname="$${1}"
eval new_rtline=$varname
/sbin/route del $new_rtline
return $?
case "$1" in
start)
if ! ck_daemon network; then
echo "Network is already running. Try 'network restart'"
exit
fi
stat_busy "Starting Network"
error=0
for ifline in ${INTERFACES[@]}; do
if echo $ifline | grep '^[^!]' >/dev/null 2>&1; then
ifup $ifline || error=1
fi
done
for rtline in "${ROUTES[@]}"; do
if echo $rtline | grep '^[^!]' 2>&1 >/dev/null; then
rtup $rtline || error=1
fi
done
if [ $error -eq 0 ]; then
add_daemon network
stat_done
else
stat_fail
fi
stop)
if ck_daemon network; then
echo "Network is not running. Try 'network start'"
exit
fi
stat_busy "Stopping Network"
rm_daemon network
error=0
for rtline in "${ROUTES[@]}"; do
if echo $rtline | grep '^[^!]' 2>&1 >/dev/null; then
rtdown $rtline || error=1
fi
done
for ifline in ${INTERFACES[@]}; do
if echo $ifline | grep '^[^!]' 2>&1 >/dev/null; then
ifdown $ifline || error=1
fi
done
if [ $error -eq 0 ]; then
stat_done
else
stat_fail
fi
restart)
$0 stop
sleep 2
$0 start
echo "usage: $0 {start|stop|restart}"
esac
Please do backup your own /etc/rc.d/network script, just in case!
Good luck,
Pascal de BruijnHow do you have your h-reap setup... how many ssid's for example? If dhcp is local, for all ssid's, then all ssid's must have local switching on unless clients will get tunneled back to the wlc and obtain an ip address there. When you say... turn on and off vlan support, you talking about the native vlan setting in the h-reap ap?
-
hello, i have the cisco router (871) and when i try to create another vlan (another than vlan1 wich is default), i get the following message:
"vlan can not be added. Maximum number of 1 vlan(s) in the database"
with the command "show vtp status" i obtein:
"maximum vlans supported locally:1"
how can i change this???
i have read that i have to update my firmware and add a new flash card, is it true??
thank you very muchi would say try updating the ios image, i have c870-advipservicesk9-mz.124-6.T.bin and i have 8 possible vlans. also check your VTP version and post what it is
-
REQ: VLAN Support for Access Connections
hi,
i would like to see VLAN support for access connections. i have a thinkpad t400
cheersVPN-User wrote:
What can be understood wrong with "VLAN support in Access Connections"? If you want to know what VLAN stands for, just google.
I know perfectly well what VLAN is since i work with networking every day and that's why i asked because i still cannot understand what maharaja mean by AC VLAN support. I asked because i might be able to help since i use VLAN with AC a lot so don't understand exactly what he find to be missing. I'm pretty sure what he is looking for is already there.
Not sure why you felt it necessary to post such a arrogant reply which is not helpful for anyone, but asking for VLAN support could be several things so that's why some further explaination would be necessary to understand what exactly the request is about. I guess you made you point to tell everyone you know what VLAN is, but then you should also realize that the question in the first post might need some further explanation since the feature might already be there.
Message Edited by gan on 04-13-2009 12:33 AM -
I was looking at the RV016, thinking that it might be perfect for a situation I have, and there seems to be many references in various forums for simpleVLAN support for this model, i.e. designating a range of physical ports to a VLAN. But the documentation on Cisco's site for this model makes no mention of VLAN support at all. Has it been removed from this model for some reason? Was this a feature on the pre-merger Linksys version that is now gone, or is the feature undocumented for some reason?
Hi Daniel,
You need to configure multiple subnets - in order to have 2 IP ranges.
Thann you need to chose different VLANs on 2 ports of RV016 (Port Management > Port Setup) - for example VLAN1 on port1 and VLAN2 on port 2 - thus you will separate the trafic on the 2 ports. You can connect your LAN on port1 and the AP for guest wifi on port2. Both subnets will have access to i-net, but not one to each other.
Regards,
Kremena
*Please rate the Post so other will know when an answer has been found. -
VLAN Support at routers and switches
is there a table with howmany VLANs each of cisco routers and switches can support.
its not always written at the product data sheet.hi
Do find the details for 1800 ISR series router..
802.1Q VLAN
A total of eight VLANs can be configured to segment a network and offer additional security and separation of network traffic.
VLAN Support
802.1Q VLAN supported on all 10/100BASE-T ports
VLAN Configured
8 VLANs
Wireless VLANs
16
7400 series has reached EOL/EOS status hence i couldnt find any datasheet for that model..
regds -
Hi, I have a linksys wrvs4400n router on which:
The wireless computers are connected to the home network (vlan 1)
Port 1 is connected to the home network (vlan 1)
Port 2 is connected to the office network (vlan 2)
And the printers are connected to port 3.
Now I'd like to setup the router in such a way that all computers have access to the printers (port 3), but I don't know what vlan settings I have to use on port 3, or if it is even possible...
I really hope someone can help me,
merc
Message Edited by merc on 06-18-2008 06:10 AMif you enable inter-vlan routing, that will allow all vlans to communicate with each other.
for your current setup, if your printer supports 802.1q, you could set the port where the printer is connected to to trunk and member it on vlans 2 and 3. -
I have just received a Cisco WRVS4400N v2.0.0.7 Router & trying to configure it like this:
2 VLANs & 2 wireless SSIDs
VLAN1 default (Port 1 on Router)
VLAN2 for Office (Port 2 on Router) &
VLAN3 for Client/Guest (Port 3 on Router) no access to VLAN2
I would also like one of the wireless SSIDs to be on the same network as VLAN2 & have access to VLAN2
Also want VLAN2 to be network 192.168.2.0
I have accomblished all except I cannot get either wireless SSID to commnicate with VLAN2
VLAN DHCP creates scopes of 192.168.3.0 & 5.0 (I need to 192.168.2.0 to match my current office network)
I know I can change the router network to 192.168.2.0 but that would mean I would have my Office network on VLAN1 (Port 1 of Router), I thought
Port 1 was for the default VLAN used for Admin stuff.
Can anyone give me some suggestions on this?
Thanks for your help in advance.
WayneHi HC-Ralph and welcome to the Cisco Home Community!
The WRVS4400N is now being handled by the Cisco Small Business Support Community.
For discussions about this product, please go here.
OnnagokorO -
Wrvs4400n vlans/ssid/dhcp issue
Hi all,
it will be great if someone will help me with my problem.
the problem is : our wrvs4400n wifi router configuration.
network description: we need 2 separated wifi networks one for guests and one for internal access, and i configured them on router, and also configured each one of them to different vlan, guests to vlan 200 and internal use default vlan 1.
vlan 1 configured as dhcp relay and its working pritty well.
vlan 200 configured as dhcp and the problem begins here.
somehow on vlan 200 i get dhcp from our externam dhcp server,
wrvs4400n conected as follow> lan port1/vlan 200 connected to firewall port(configured as vlan 200) and lan port 4/vlan1 conected to our main switch wich connected to firewall also.
i guess that my knowlege in networking its not so good......
how can i prevent from our internal dhcp to comunicate with vlan 200 ,
any help will be very appreciated.Hi Rich,
You cannot have different L3 VLANs sharing the same subnet.
Each VLAN must have it's own subnet and then you have a routing device routing between both VLANs.
You should have a DHCP pool also for VLAN 111 configured on the DHCP server.
Even if you have ip helper address configured and this should be done on the VLAN111 interface of the switch, you still need a DHCP pool for VLAN 111 because the DHCP discovery is coming on VLAN 111.
Please take a look into this document:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080665ceb.shtml.
Here it explains how to configure 2 ssids on 2 vlans and dhcp pool (on the switch itself) for each vlan.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it. -
802.1X with Guest vlan support IOS version ???
I don't know, Whitch IOS version support 802.1X with Guest vlan to Catalyst 2950 and 3550 switch
please reply to my question.Tkank for your help.
Also, Cisco web is explained , except for Catalyst 2950 Standard Image (SI) in IOS 12.1(22)EA3
but I can't understand, My site is using catalyst 2950 SI to 802.1X and guest vlan in IOS image 12.1(22)EA3
ex) TW_14F_A_C2950_32.8#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA3, RELEASE SOFTWARE (fc1)
Running Standard Image
24 FastEthernet/IEEE 802.3 interface(s)
Model number: WS-C2950-24
please, reply for my question -
Hi Cisco experts,
My name is Kumagai and I need your expert opinions below.
I am trying to configure one VLAN1 support multiple network segments as below.
(this should be a very straight forward configuration and should be OK, I think ? )
interface Vlan1
ip address 172.30.0.0 255.255.128.0
ip address 172.30.31.253 255.255.254.0 secondary
ip address 172.30.61.253 255.255.254.0 secondary
ip address 172.30.71.253 255.255.254.0 secondary
ip address 172.30.4.253 255.255.255.0 secondary
The only issue that is eating me is the above network segments are using HSRP too
and I am not sure is this possible with a combination of VLAN1 supporting multiples which are
further supported with HSRP settings in Cisco environment.
!example of HSRP:
interface Vlan4
ip address 172.30.4.253 255.255.255.0
no ip redirects
standby 4 ip 172.30.4.254
standby 4 priority 105
standby 4 preempt
<<< what will happen if I add the HSRP configuration as below into the above VLAN1 with multiple Network segment ??)
I would like to summarize my "Combined" configurations as below but I need your expert opinions on
whether the configuration below is workable without any problem ??
Or it is a total flop because Cisco does not support the configuration below !!!
interface Vlan1
ip address 172.30.0.0 255.255.128.0
ip address 172.30.31.253 255.255.254.0 secondary
ip address 172.30.61.253 255.255.254.0 secondary
ip address 172.30.71.253 255.255.254.0 secondary
ip address 172.30.4.253 255.255.255.0 secondary
standby 30 ip 172.30.31.254
standby 30 priority 105
standby 30 preempt
standby 60 ip 172.30.61.254
standby 60 priority 105
standby 60 preempt
standby 70 ip 172.30.71.254
standby 70 priority 105
standby 70 preempt
standby 4 ip 172.30.4.254
standby 4 priority 105
standby 4 preempt
Thanking you in advance !!!!!Hi,
As far as i know we dont set the ip helper address on the radio interface. It should be on the L3 interface of corresposding VLANs i.e.
int vlan 20
ip helper-address 192.168.33.xxx
int vlan 60
ip helper-address 130.20.1.xxx
I'm assuming that your using SVI's (int Vlan 20 and int Vlan 60) rahter than physical interfaces. Also hope you have configured switch port as trunk where this AP is connected.
Modify the AP config as below since you are using data vlan as the native vlan
interface Dot11Radio0.20
encapsulation dot1Q 20 native
interface FastEthernet0.20
encapsulation dot1Q 20 native
Ideally your AP fastethernet configuration should looks like below and not sure how you missed this as this comes by default when you have multiple vlans for multiple ssids.
interface FastEthernet0.20
encapsulation dot1Q 20 native
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface FastEthernet0.60
encapsulation dot1Q 60
no ip route-cache
bridge-group 60
no bridge-group 60 source-learning
bridge-group 60 spanning-disabled
Hope this helps.
Regards
Najaf
Maybe you are looking for
-
Is it possible to start planning manager programatically from backend through PL/SQL?
I need to activate and run Planning manager concurrent program from back end through PL/SQL.Actually i am working on MRP Open Forecast Interface and I want to run this program after inserting data in the interface table mrp_forecast_interface.Please
-
Hi, I have a 1:N File to IDOC scenario which I need to do without using CCBPM.I am using the RB_Split feature in Interface Determination. Could someone please explain to me, the steps I need to take? I have SP14 installed. regards, Prashanth
-
Hi all, Been searching the archives. I've developed a Swing standalone app and would like to convert it into a "Rick Client" but shifting certain parts over to a backend. My initial work has been a servlet on Tomcat webserver I maintain. Can anyone p
-
Edit menu - allowing copy/cut/paste
I am working on creating an edit menu and I would like to be able to disable the copy/cut/paste items in the menu when their use is not possible (like when there is no text based field to copy from). I am guessing that one approach I can take is as f
-
All files I save to the desktop, any external volumes I mount all end up in the bottom right corner of my desktop stacked on top of each other. Any ideas? Power Mac G4 Mac OS X (10.4.8)