X1 Carbon (20A7) wont pxe boot

We just got in our first of 7 x1 carbons (20a7) and im am trying to prepare our imaging enviornment to handle the new model.
We have included ethernet extender (FRU 04X6435) which works fine in windows but when pxe booting i can see the MAC address and it waits for DHCP (the link and activity light on the extender do flash) after a few seconds we get a PXE-E53: no bootfile message and then get dumped back to the boot menu.
I can pxe boot other machines off the same ethernet jack at my desk. Other laptops x230, t430s, all no problems.
I have tried UEFI/legacy boot on both and on legacy only neither change the outcome. Since we are not using a usb adapter (this is the extender cable on the new x1s) i have not touched the usb settings.
I have searched aroudn and found the threads of the older x1 carbons that used the usb 2.0 adapters but nothing on this new extender and it seems in those cases people were getting into the pxe environment and then having driver issues. I am not even getting that far.
Our pxe enviornment (WDS) is setup to require a press of f12 on the client to actually boot and i never even get prompted for f12. Im really not even sure im getting DHCP right other than any other machine i plug is works fine.
Any help is greatly appreciated.
Thanks,
Eric

this seems to have caused uneven lighting in the LED display, very strange problem. You may need to get warranty service on it.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Similar Messages

X1 carbon 20A7 won't boot after 1.13 BIOS update, ecreen also corrupted.

After updating the BIOS to 1.13 the X1 refuses to boot . After several attempts to diagnose the problem (trying to boot under legacy and uefi with various rescue pen drives) I doing a restore with the recovery media (created using the inbuilt software) but that didn't help, it just wiped my partitions and reinstalled windows (I'm assuming since I have no way to check at this point) but still refuses to boot. I can boot the windows rescue thumb drive under legacy though. After the update the screen was also corrupted, picture here http://i.imgur.com/ScfD1Uz.jpg.
At this point I'm not sure what to do anymore, it seems that the BIOS update failed in some way or somehow broke something.

this seems to have caused uneven lighting in the LED display, very strange problem. You may need to get warranty service on it.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Yoga S1 wont PXE, secure boot affecting it.

Help needed....
I have a Lenovo S1 yoga, and i cant PXE boot it. SIMPLE, there is o option to NIC option shown.
I have a Microsoft System center 2012 which deploys images via pxe, this works for T540. M93 and T440 and previous same model Yogas. The base image is a company version of Windows 8.1Pro.
I have a Lenovo Onelink dock, and have included the one dock driver into the wim image.
The problem lies with the BIOS and the the function you cant switch OFF the secure boot and put boot into both boot mode, legacy first, i have saved it and every time it saves and reboots it SWITCHES the secure boot back ON !
This doesn't display any option to boot from anything other the HDD or windows boot manager on restart.
i have also disabled the OS optimized defaults which switches back on after reboot.....
This has been successful in the past and i have captured the base image for our Yoga machines.
i have even upgraded firmware 1.18 -1.20 hoping it might put the feature back or do something.
The FEATURE has rendered the machines useless and if i cant find an answer back to supplier it is..
I have bought 4 of these machines and i don't know what has changed but might have to rethink our Lenovo structure as this feature renders them non company friendly.
20CDOOCUAU
i7 2.0GHZ
8GB
Can anyone help.....please
P.S
Went to look at the old machines which was successful, they are on FW 1.15, was this an addition?

Went to look at the old machines which was successful, they are on FW 1.15, was this an addition?

Lenovo X1 Carbon PXe boot errors with SCCM 2007

I know there are many posts on this and I've gone through them all, but I am still having issues PXe booting a X1. I have a USB ethernet dongle (the new type with the rounded edge). the part number is 0b67708. It's branded Lenovo but when I pxe it recognises it as ASIX AX88772b. So far so good. It picks up an IP from DHCP ok, recognises the hardware as x64 and then tries to download the \smsboot\boot.sdi file from the SCCM 2007 server. It waits for 20 seconds then falls over with the following:
Status: 0xc0000001 - Info: The boot selection failed because a required device is inaccessible.
Now, I have the the following drivers in the boot.wim file:
x86 -
1. Lenovo USB2.0 Ethernet Adapter 5.12.7.0
2. PCI bus
3. Intel ICHR/DO/DH SATA AHCI Controller
4. Intel USB 3.0 Root Hub
5. Intel USB 3.0 eXtensible Host Controller
x64 -
1. Lenovo USB 2.0 Ethernet Adapter 5.14.4.0
2. PCI Bus
3. Intel ICHR/DO/DH SATA AHCI Controller - 2821
4. Intel USB 3.0 Root Hub
5. Intel USB 3.0 eXtensible Host Controller
I have tried using the ASIX drivers, all previous driver version, adding in the mass storage drivers, adding in the USB 3.0 drivers, praying to the PXe gods but nothing works.
All other hardware works fine. Any suggestions greatly welcomed.
Cheers - Mark.

Make a USB recovery drive before reinstalling.Thats the only option with a preload. With a retail serial number, you can download an iso with the upgrade assistant.
Also, how much ram do you have. If yopu have more than 4GB, you will need 64 bit XP, or the performance will take a hit. I tried XP on my W530, but I had to change several settings in the BIOS/UEFI.
W530(2436-CTO): i7-3720QM, nVidia Quadro K2000M,16GB RAM, 500 GB hard drive, 128GB mSATA SSD, Ubuntu 14.04 Gnome, Centrino Ultimate-N 6300.
Yoga 3 Pro: Intel Core-M 5Y70, Intel HD 5300, 8GB RAM, 128GB eMMC, Windows 8.1, Broadcom Wireless 802.11ac.

Yoga 2 Pro PXE boot?

Looking to PXE boot a Yoga 2 Pro so I can create/restore images with Microsoft WDS. Since Yoga 2 Pro does not have a built-in Ethernet jack, does anyone know if it's possible to do this with a USB Ethernet adapter?
Would it have to be a Lenovo-branded apdater, or can any brand Belkin, TP-Link, etc) work?

How did you get this to work sir?? I have been trying for a solid week and it never see the Lenovo ethernet dongle as a boot option no matter what I choose in the BIOS. I have the X1 Carbon and it works as you would expect it to. But it NEVER works on the YOGA 2 PRO. CAn anyone help me?? The BIOS clearly has an option to boot the dongle thats made by LENOVO but the dongle never ever shows any lights no matter what port its in or regardless of the settings vchanged in the very small bios. I have wasted atleast 60 hrs + trying to figure out how to boot with it and it doesnt work at all. I had to end up making a bootable discover USB to help it find my wds server. Altough now when ever I attempt to drop an image to it it fails right at FINISHING up and finishes with a "corrupt installation file" error message. To make things more confusing is I can drop this same "Corrupt" image to our X1 carbons without a problem. Can anyone guess why??

Can't PXE boot a Surface Pro 3 after already successfully imaging it

hey guys. To try to eliminate a lot of the initial question that come up with this issue, I figure I will start with established info. Our SCCM environment is healthy, and all images, drivers and apps are distributed to all of our DP's. We can image
PC's and laptops with no issue at all. We use network PXE booting. Using a 64 bit boot image. Needed drivers are injected into the boot image. Firmware on the Surface was updated. Using the Surface NIC dongle. THis dongle was only used to image
this Surface Pro 3 tablet one time. There is no record of the MAC of the dongle in SCCM since I deleted the Surface out, to make it an unknown again.
So, with a lot of trial and error, I was finally able to get this tab to PXE boot, and then successfully image. Was testing out the new windows 8.1 image I had built.
Since it ewas successful I wanted to add all of our apps to the TS and test them out in imaging. Well, I can no longer get this thing to PXE boot. It shows trying to Start PXE over IPv4, then just skips to IPv6, then boots up into windows.
I have delted the secure keys form ther BIOS, then reloaded them. I have tried hte full shut down method (Holding Volume Up and Power for 15 seconds, then waiting for 10 seconds or longer, then trying to PXE boot. I am getting a valid connection fro
mthe dongle.
Nothinhg I try works. Its tries to PXE boot over IPv4, but never gets there. But I can PXE boot any of our PC's or Laptops,m so its just an issue with this damn Surface Pro 3.
ANy advice?

So I finally got our server guy to enable the logging and get that smspxe.log file to be accessible. So here is the info from the log, when I attempt to PXE boot the Surface. I see the last 2 lines where it ignores the request, I just don't know why its
ignoring it.
PXE::CNotifyTimer::TimerSignalFunc SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
PXE::CNotifyTimer::ProcessTimer SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
Potentially missed device 50:1A:C5:FE:D6:E9 SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
Cleared Old Devices: 1 / 1 SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
PXE::CBootImageManager::PerformMaintenenceTasks SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
PXE::CBootImageManager::PurgeOldImages SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
Purging old images: 0 SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
PXE::CNotifyTimer::Init SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
PXE::CNotifyTimer::CancelTimer SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
PXE::CNotifyTimer::RegisterTimeout SMSPXE 4/14/2015 3:04:18 PM 8896 (0x22C0)
[172.028.000.223:67] Recv From:[172.028.011.002:67] Len:347 1ad0230 SMSPXE 4/14/2015 3:04:37 PM 5928 (0x1728)
============> Received from client: SMSPXE 4/14/2015 3:04:37 PM 5928 (0x1728)
DHCP message:
Operation: BootRequest (1)
Hardware Address type: 1
Hardware Address Length: 6
Hop Count: 1
Transaction ID: 24038353
Seconds Since Boot: 0
Client IP Address: 000.000.000.000
Your IP Address: 000.000.000.000
Server IP Address: 000.000.000.000
Relay Agent IP Address: 172.028.011.002
Hardware Address: 50:1a:c5:fe:d6:e9:
Magic Cookie: 63538263
Options:
    Type = 53 DHCP Message Type: 1=DHCPDiscover
    Type = 57 Max DHCP Message Size: 05b8
    Type = 55 Paramerter Request List: 0102030405060c0d0f111216171c28292a2b3233363a3b3c4243618081828384858687
    Type = 97 UUID: 0068745ee6b94c0e21b76054522b6a7e02
    Type = 94 UNDI: 010310
    Type = 93 Client system Arch: 0007
    Type = 60 ClassIdentifier: PXEClient:Arch:00007:UNDI:003016 SMSPXE 4/14/2015 3:04:37 PM 5928 (0x1728)
<============ SMSPXE 4/14/2015 3:04:37 PM 5928 (0x1728)
ProcessMessage: Context:0241DF40 dTime:0 SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
50:1A:C5:FE:D6:E9, E65E7468-4CB9-210E-B760-54522B6A7E02: DHCP Discover received. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
[172.028.000.223:67] Recv From:[172.028.011.003:67] Len:347 159d1f0 SMSPXE 4/14/2015 3:04:37 PM 5928 (0x1728)
============> Received from client: SMSPXE 4/14/2015 3:04:37 PM 5928 (0x1728)
DHCP message:
Operation: BootRequest (1)
Hardware Address type: 1
Hardware Address Length: 6
Hop Count: 1
Transaction ID: 24038353
Seconds Since Boot: 0
Client IP Address: 000.000.000.000
Your IP Address: 000.000.000.000
Server IP Address: 000.000.000.000
Relay Agent IP Address: 172.028.011.003
Hardware Address: 50:1a:c5:fe:d6:e9:
Magic Cookie: 63538263
Options:
    Type = 53 DHCP Message Type: 1=DHCPDiscover
    Type = 57 Max DHCP Message Size: 05b8
    Type = 55 Paramerter Request List: 0102030405060c0d0f111216171c28292a2b3233363a3b3c4243618081828384858687
    Type = 97 UUID: 0068745ee6b94c0e21b76054522b6a7e02
    Type = 94 UNDI: 010310
    Type = 93 Client system Arch: 0007
    Type = 60 ClassIdentifier: PXEClient:Arch:00007:UNDI:003016 SMSPXE 4/14/2015 3:04:37 PM 5928 (0x1728)
<============ SMSPXE 4/14/2015 3:04:37 PM 5928 (0x1728)
ProcessMessage: Context:0241DE50 dTime:0 SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
50:1A:C5:FE:D6:E9, E65E7468-4CB9-210E-B760-54522B6A7E02: DHCP Discover received. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Initialized CStringStream object with string: c7c22c7d-4f40-49f1-b7ed-871c18a07b05;2015-04-14T19:04:37Z. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Initialized CStringStream object with string: c7c22c7d-4f40-49f1-b7ed-871c18a07b05;2015-04-14T19:04:37Z. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Set enterpirse certificate in transport SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Set enterpirse certificate in transport SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Set media certificate in transport SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Set authenticator in transport SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
CLibSMSMessageWinHttpTransport::Send: URL: JAG-SCCM-01E.jonesapparel.com:443 GET /SMS_MP_AltAuth/.sms_aut?MPKEYINFORMATIONEX SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
In SSL, but with no client cert SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Set media certificate in transport SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Set authenticator in transport SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
CLibSMSMessageWinHttpTransport::Send: URL: JAG-SCCM-01E.jonesapparel.com:443 GET /SMS_MP_AltAuth/.sms_aut?MPKEYINFORMATIONEX SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
In SSL, but with no client cert SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Request was successful. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Request was successful. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Set authenticator in transport SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Set authenticator in transport SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Setting message signatures. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Setting the authenticator. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
CLibSMSMessageWinHttpTransport::Send: URL: JAG-SCCM-01E.jonesapparel.com:443 CCM_POST /ccm_system_AltAuth/request SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
In SSL, but with no client cert SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Setting message signatures. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Setting the authenticator. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
CLibSMSMessageWinHttpTransport::Send: URL: JAG-SCCM-01E.jonesapparel.com:443 CCM_POST /ccm_system_AltAuth/request SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
In SSL, but with no client cert SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Request was successful. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
::DecompressBuffer(65536) SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Decompression (zlib) succeeded: original size 148, uncompressed size 298. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Client lookup reply: <ClientIDReply><Identification Unknown="0" ItemKey="0" ServerName=""><Machine><ClientID/><NetbiosName/></Machine></Identification></ClientIDReply>
SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
MP_LookupDevice succeeded: 0 1 0 1 0 SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
50:1A:C5:FE:D6:E9, E65E7468-4CB9-210E-B760-54522B6A7E02: device is not in the database. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Getting boot action for unknown machine: item key: 2046820352 SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Request was successful. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
::DecompressBuffer(65536) SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Decompression (zlib) succeeded: original size 148, uncompressed size 298. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Client lookup reply: <ClientIDReply><Identification Unknown="0" ItemKey="0" ServerName=""><Machine><ClientID/><NetbiosName/></Machine></Identification></ClientIDReply>
SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
MP_LookupDevice succeeded: 0 1 0 1 0 SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
50:1A:C5:FE:D6:E9, E65E7468-4CB9-210E-B760-54522B6A7E02: device is not in the database. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Getting boot action for unknown machine: item key: 2046820352 SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Initialized CStringStream object with string: c7c22c7d-4f40-49f1-b7ed-871c18a07b05;2015-04-14T19:04:37Z. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Set enterpirse certificate in transport SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Initialized CStringStream object with string: c7c22c7d-4f40-49f1-b7ed-871c18a07b05;2015-04-14T19:04:37Z. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Set enterpirse certificate in transport SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Set media certificate in transport SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Set authenticator in transport SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
CLibSMSMessageWinHttpTransport::Send: URL: JAG-SCCM-01E.jonesapparel.com:443 GET /SMS_MP_AltAuth/.sms_aut?MPKEYINFORMATIONEX SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
In SSL, but with no client cert SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Set media certificate in transport SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Set authenticator in transport SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
CLibSMSMessageWinHttpTransport::Send: URL: JAG-SCCM-01E.jonesapparel.com:443 GET /SMS_MP_AltAuth/.sms_aut?MPKEYINFORMATIONEX SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
In SSL, but with no client cert SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Request was successful. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Request was successful. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Set authenticator in transport SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Set authenticator in transport SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Setting message signatures. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Setting the authenticator. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
CLibSMSMessageWinHttpTransport::Send: URL: JAG-SCCM-01E.jonesapparel.com:443 CCM_POST /ccm_system_AltAuth/request SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
In SSL, but with no client cert SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Setting message signatures. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Setting the authenticator. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
CLibSMSMessageWinHttpTransport::Send: URL: JAG-SCCM-01E.jonesapparel.com:443 CCM_POST /ccm_system_AltAuth/request SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
In SSL, but with no client cert SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Request was successful. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
::DecompressBuffer(65536) SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Decompression (zlib) succeeded: original size 409, uncompressed size 950. SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="2046820352" ServerName=""><Machine><ClientID>c70485df-9130-4b41-b61b-6c9e11b2f69a</ClientID><NetbiosName/></Machine></Identification><PXEBootAction
LastPXEAdvertisementID="" LastPXEAdvertisementTime="" OfferID="10020125" OfferIDTime="4/2/2015 11:12:00 AM" PkgID="100000D0" PackageVersion="" PackagePath BootImageID="10000087" Mandatory="0"/></ClientIDReply>
SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Client Identity: c70485df-9130-4b41-b61b-6c9e11b2f69a SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
50:1A:C5:FE:D6:E9, E65E7468-4CB9-210E-B760-54522B6A7E02: SMSID=c70485df-9130-4b41-b61b-6c9e11b2f69a OfferID=10020125, PackageID=100000D0, PackageVersion=, BootImageID=10000087, PackagePath=http://JAG-SCCM-01E.jonesapparel.com/SMS_DP_SMSPKG$/10000087, Mandatory=0 SMSPXE 4/14/2015
3:04:37 PM 7484 (0x1D3C)
50:1A:C5:FE:D6:E9, E65E7468-4CB9-210E-B760-54522B6A7E02: found optional advertisement 10020125 SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
============> Reply to client (DHCPDISCOVER): SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
DHCP message:
Operation: BootReply (2)
Hardware Address type: 1
Hardware Address Length: 6
Hop Count: 0
Transaction ID: 24038353
Seconds Since Boot: 0
Client IP Address: 000.000.000.000
Your IP Address: 000.000.000.000
Server IP Address: 172.028.000.223
Relay Agent IP Address: 172.028.011.002
Hardware Address: 50:1a:c5:fe:d6:e9:
Magic Cookie: 63538263
Options:
    Type = 53 DHCP Message Type: 2=DHCPOffer
    Type = 54 Server idenitifier: 172.028.000.223
    Type = 97 UUID: 0068745ee6b94c0e21b76054522b6a7e02
    Type = 60 ClassIdentifier: PXEClient SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
<============ SMSPXE 4/14/2015 3:04:37 PM 7484 (0x1D3C)
Request was successful. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
::DecompressBuffer(65536) SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Decompression (zlib) succeeded: original size 409, uncompressed size 950. SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="2046820352" ServerName=""><Machine><ClientID>c70485df-9130-4b41-b61b-6c9e11b2f69a</ClientID><NetbiosName/></Machine></Identification><PXEBootAction
LastPXEAdvertisementID="" LastPXEAdvertisementTime="" OfferID="10020125" OfferIDTime="4/2/2015 11:12:00 AM" PkgID="100000D0" PackageVersion="" PackagePath="xx
BootImageID="10000087" Mandatory="0"/></ClientIDReply>
SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
Client Identity: c70485df-9130-4b41-b61b-6c9e11b2f69a SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
50:1A:C5:FE:D6:E9, E65E7468-4CB9-210E-B760-54522B6A7E02: SMSID=c70485df-9130-4b41-b61b-6c9e11b2f69a OfferID=10020125, PackageID=100000D0, PackageVersion=, BootImageID=10000087, PackagePath=http://JAG-SCCM-01E.jonesapparel.com/SMS_DP_SMSPKG$/10000087, Mandatory=0 SMSPXE 4/14/2015
3:04:37 PM 7480 (0x1D38)
50:1A:C5:FE:D6:E9, E65E7468-4CB9-210E-B760-54522B6A7E02: found optional advertisement 10020125 SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
============> Reply to client (DHCPDISCOVER): SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
DHCP message:
Operation: BootReply (2)
Hardware Address type: 1
Hardware Address Length: 6
Hop Count: 0
Transaction ID: 24038353
Seconds Since Boot: 0
Client IP Address: 000.000.000.000
Your IP Address: 000.000.000.000
Server IP Address: 172.028.000.223
Relay Agent IP Address: 172.028.011.003
Hardware Address: 50:1a:c5:fe:d6:e9:
Magic Cookie: 63538263
Options:
    Type = 53 DHCP Message Type: 2=DHCPOffer
    Type = 54 Server idenitifier: 172.028.000.223
    Type = 97 UUID: 0068745ee6b94c0e21b76054522b6a7e02
    Type = 60 ClassIdentifier: PXEClient SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
<============ SMSPXE 4/14/2015 3:04:37 PM 7480 (0x1D38)
[172.028.000.223:67] Recv From:[172.028.011.003:67] Len:359 1acbeb0 SMSPXE 4/14/2015 3:04:40 PM 5928 (0x1728)
[172.028.000.223:67] Recv From:[172.028.011.002:67] Len:359 15a41f0 SMSPXE 4/14/2015 3:04:40 PM 5972 (0x1754)
============> Received from client: SMSPXE 4/14/2015 3:04:40 PM 5928 (0x1728)
============> Received from client: SMSPXE 4/14/2015 3:04:40 PM 5972 (0x1754)
DHCP message:
Operation: BootRequest (1)
Hardware Address type: 1
Hardware Address Length: 6
Hop Count: 1
Transaction ID: 24038353
Seconds Since Boot: 0
Client IP Address: 000.000.000.000
Your IP Address: 000.000.000.000
Server IP Address: 000.000.000.000
Relay Agent IP Address: 172.028.011.003
Hardware Address: 50:1a:c5:fe:d6:e9:
Magic Cookie: 63538263
Options:
    Type = 53 DHCP Message Type: 3=DHCPRequest
    Type = 54 Server idenitifier: 172.028.000.015
    Type = 50 Requested IP: 172.028.011.052
    Type = 57 Max DHCP Message Size: ff00
    Type = 55 Paramerter Request List: 0102030405060c0d0f111216171c28292a2b3233363a3b3c4243618081828384858687
    Type = 97 UUID: 0068745ee6b94c0e21b76054522b6a7e02
    Type = 94 UNDI: 010310
    Type = 93 Client system Arch: 0007
    Type = 60 ClassIdentifier: PXEClient:Arch:00007:UNDI:003016 SMSPXE 4/14/2015 3:04:40 PM 5928 (0x1728)
DHCP message:
Operation: BootRequest (1)
Hardware Address type: 1
Hardware Address Length: 6
Hop Count: 1
Transaction ID: 24038353
Seconds Since Boot: 0
Client IP Address: 000.000.000.000
Your IP Address: 000.000.000.000
Server IP Address: 000.000.000.000
Relay Agent IP Address: 172.028.011.002
Hardware Address: 50:1a:c5:fe:d6:e9:
Magic Cookie: 63538263
Options:
    Type = 53 DHCP Message Type: 3=DHCPRequest
    Type = 54 Server idenitifier: 172.028.000.015
    Type = 50 Requested IP: 172.028.011.052
    Type = 57 Max DHCP Message Size: ff00
    Type = 55 Paramerter Request List: 0102030405060c0d0f111216171c28292a2b3233363a3b3c4243618081828384858687
    Type = 97 UUID: 0068745ee6b94c0e21b76054522b6a7e02
    Type = 94 UNDI: 010310
    Type = 93 Client system Arch: 0007
    Type = 60 ClassIdentifier: PXEClient:Arch:00007:UNDI:003016 SMSPXE 4/14/2015 3:04:40 PM 5972 (0x1754)
<============ SMSPXE 4/14/2015 3:04:40 PM 5928 (0x1728)
<============ SMSPXE 4/14/2015 3:04:40 PM 5972 (0x1754)
Ignoring req from [172.028.011.003:67] Dest Server:[172.028.000.015] SMSPXE 4/14/2015 3:04:40 PM 5928 (0x1728)
Ignoring req from [172.028.011.002:67] Dest Server:[172.028.000.015] SMSPXE 4/14/2015 3:04:40 PM 5972 (0x1754)

Problems PXE booting Gen 2 Virtual Machines after Upgrading to Windows Server 2012 R2

My Current Setup:
I have two virtual machines set up with Hyper V on my Windows Server 2012 Server.
VM1: Configured to boot from an ISO file and runs Clonezilla server.
VM2: Configured to PXE boot using a legacy network adapter, and with a passthrough 250Gb hard disk.
These two VMs are connected to an external Virtual Switch, which allows physical machines to PXE boot to the Clonezilla server.
For the past few months I have been using this setup for two purposes:
1. To clone physical machines to the Clonezilla virtual server (as a backup).
2. To restore those image to the second VM if I find that need to get access to the files on the original image..
This has worked perfectly, except for the fact that the speed of the legacy network adapter on the second VM (which is required to PXE boot) is very slow. But I know this is because of the limitations in how the legacy adapter works...
Now my problem:
I found out that Gen 2 VMs allow you to PXE boot without having use a legacy network adapter, allowing me to image back to the VM faster. So I upgraded the Server to Server 2012 R2 . I then created the same two virtual machines on the R2 server. I can still
PXE boot the Gen 1 VM to the Clonezilla Server but I cannot get the Gen 2 VMs to PXE boot properly. They get an IP address from the Clonezilla Server but then just stop with the following screen. (note: I have disabled the Secure Boot).
Are Gen 2 VMs unable to pull down images from anything other than a WDS Server?

Hi J,
>>Unfortunately WDS is not a solution for us as it is dependent on the PC being part of a domain
If you would like to make the client not join to the domain, please check the box before “Do not join the client to a domain after an installation.” In addition, make sure not to set the client to the domain in the unattend file and do not prestage
the computer in AD. "
It is quoted from following thread :
https://social.technet.microsoft.com/Forums/windowsserver/en-US/1026c3a9-0a10-4a58-a48f-5391659a96c8/wds-set-unattend-file-for-workgroup?forum=winserversetup
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

PXE boot no longer working - blank cmd windows shown. If run Scripts/Litetouch file from target machine wizards runs as expected??

Hi, My MDT server no longer works as expected via PXE boot. After the target machine loads the .wim file an empty command windows is shown. I have returned the custom settings.ini and bootstrap files to default and ensured nothing is being skipped within
the task sequence within both files in hope of viewing the wizard.
However from the same target machine if I map drive to my Deploymentshare/Scripts directory and run LiteTouch file I am asked for domain credentials and the Deployment wizard is displayed asking for task sequence to be selected.
I believe this error is a result of two things:
1) I applied some windows updates to my mdt server (running on 2008 r2).
2) I was implementing changes to
ZTIWindowsUpdate.wsf which i have now returned to default settings.
I have also regenerated boot images and re added to WDS.
Any help much appreciated?
Regards,
Paul

Hi Paul,
This sounds familiar; I only encounter this behaviour with certain kinds of laptops (Latitude E65x0) but I usually just provide the "wpeutil reboot" command in the empty command window to keep things going. All other hardware is deployed with the
same task sequence and this behaviour does not occur anywhere else...
A bit obvious maybe, but did you check if there is still a "Next Phase" step present and enabled following directly after the "Install Operating System" step?

Windows Deployment Services Unable to PXE boot clients PXE-E53: No Boot Filename Received

Hi
I'm trying to configure WDS/MDT to deploy Windows 8.1. I've captured an image and I'm ready to deploy the image to a workstation, as per the above title when I attempt to PXE boot a test workstation it just times out with the following error message PXE-E52:No
Boot Filename Recieved. I've tried a few tweaks to get it working however no such luck.
The setup is as follows it's a virtual Windows 2012 R2 machine, just a fresh member server with microsoft deployment toolkit installed and WDS role installed with the nesscary framework features installed.
I've tried tweaking the properties of most of the settings within the server settings in WDS with no such luck.
I'm a novice at WDS but from what I've read I shouldn't need configure that much in the first place to get it working.
I'm willing to bet it will be something I've overlooked so I need a 2nd opinon, could anyone provide any troubleshooting tips. If you require anymore information please let me know.
Cheers

Hi Joel,
This error may caused by the WDS server is not pushing the images because PXE Clients are not able to download or communicate with the TFTP server.
The image can’t be download generally caused by the the Vlan is not enabled IP helper/DHCP relay agent configured on it, all DHCP broadcasts on UDP port 67 by client computers
should be forwarded directly to both the DHCP server and the Windows Deployment Services PXE server.
The related KB:
PXE clients computers do not start when you configure the Dynamic Host Configuration Protocol server to use options 60, 66, 67
http://support.microsoft.com/kb/259670
The similar thread:
PXE-E53: No boot filename received
http://social.technet.microsoft.com/Forums/systemcenter/en-US/8de3bd6a-f8ec-41d9-ae0f-5b2fdb9e5831/pxee53-no-boot-filename-recieved?forum=configmgrosd
WDSServer (Windows Deployment Server) Fails to Start
http://social.microsoft.com/Forums/en-US/d96b0b86-f2b0-49a5-8946-19ab515f23e6/wdsserver-windows-deployment-server-fails-to-start?forum=windowshpcitpros
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

PXE boot issue with DHCP and SCCM server on different subnets

I'm working with a client on the operating system deployment module of SCCM.
Their network configuration currently has a single large subnet for client
computers with a DHCP server on the same subnet. The SCCM subnet is
configured on a seperate subnet with no DHCP server on the subnet. We want to
configure client computers to be able to boot using the PXE client to deploy
OS images to the machines but can not get PXE-boot to work correctly.
Also, the client does not want to make changes to their network
infrastructure routers or switches to remedy this problem. Are there settings
on the DHCP or SCCM servers we can implement to make this work? If so, what
needs to be installed or configured on each server. We currently already have
WDS installed on the SCCM server and the SCCM server is configured as a PXE
Service Point within SCCM. Both WDS and the PXE Service Point seem to be working fine.
Any help would be appreciated.
Thanks,
Gary

I am Brazilian,
sorry for wrong english
My DHCP is on linux,
in my own structure VLANS
The system center is on the network
10.0.4.0/24
The machines on the network 10.0.5.0/24
The problem is that the machines that
are not on the same network system center
can not boot
I tried configuring / etc/dhcp3/dhcpd.conf
follows
option vendor-class-identifier "PXEClient";
option bootfile-name "\
\ SMSBOOT \ \ x86 \
\ wdsnbp.com";
option tftp-server-name
"10.0.4.101"; ---->
IP server
But it did not work, anyone know
how to configure?

Machines cannot PXE boot using SCCM 2012 DP

There are a lot of posts about PXE boot, but I can't find the common thread to tie them all together. My test machines cannot PXE boot.
My lab environment is very simple:
10.10.0.0/24 subnet
10.10.0.10 = W2k8 R2 DC, DHCP, DNS
10.10.0.11 = SCCM2012 (on W2k8R2 with SQL Server 2008 SP3 and CU4)
All machines are Hyper-V virtual machines connecting through the same virtual network.
Setup the PXE service from DP properties. I let SCCM install WDS. WDS in Server Manager does not have a server node, but the WDS service is running. DP PXE tab is configured as follows:
"Enable PXE support for clients" is checked
"Allow this distribution point to resond to incoming PXE requests" is checked
"Enable unknown computer support" is checked
"Require a password when computers use PXE" is not checked
"User device affinity" is set to "Allow user device affinity with automatic approval"
PXE is configured to respond on all network interfaces
The PXE server response delay is 0 seconds
The DHCP server has options configured as follows:
Option 66: 10.10.0.11
Option 67: smsboot\x86\wdsnbp.com
Both DP and MP on SCCM server are configured for HTTP.
Both x86 and x64 boot images have been distributed to DP. The media was updated after PXE was enabled on the DP.
Both x86 and x64 boot images have "Deploy this image from the PXE service point" enabled on the Data Source tab of their properties.
I have tried both unknown computer task sequence and a computer import task sequence (old computer association). They all end in abortpxe.com
Complete PXE response is as follows:
=================================================================
PXE Network Boot 03.23.2009
(C) Copyright 2009 Microsoft Corporation, All Rights Reserved
CLIENT MAC ADDR: 00 DD CC BB AA 00 GUID: 532D27E3-A184-4D27-A822-30A8B6F4A39D
CLIENT IP: 10.10.0.106 MASK: 255.255.255.0 DHCP IP: 10.10.0.10
GATEWAY IP: 10.10.0.5
Download WDSNBP...
Architecture: x64
WDSNBP started using DHCP Referral.
Contacting Server: 10.10.0.11 (Gateway: 0.0.0.0)
The detalis below show the information relating to the PXE boot request for
this computer. Please provide these details to your Windows Deployment Services
Administrator so that this request can be approved.
Pending Request ID: 6
Contacting Server: 10.10.0.11
TFTP Download: smsboot\x64\abortpxe.com
PXE Boot aborted. Booting to next device
===========================================================
From the smspxe.log:
]LOG]!><time="16:31:39.445+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:6402">
<![LOG[Client Identity: {C9929C4D-735A-4973-8659-4D3D5D5E4F92}]LOG]!><time="16:31:39.445+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:6428">
<![LOG[Set enterpirse certificate in transport]LOG]!><time="16:31:39.480+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:9207">
<![LOG[Set media certificate in transport]LOG]!><time="16:31:39.505+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:9220">
<![LOG[Set authenticator in transport]LOG]!><time="16:31:39.505+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:7592">
<![LOG[Set authenticator in transport]LOG]!><time="16:31:39.533+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:7592">
<![LOG[PXE::CBootImageManager::FindMatchingArchitectureBootImage]LOG]!><time="16:31:39.553+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="bootimagemgr.cpp:1736">
<![LOG[PXE::CBootImageManager::FindMatchingArchitectureBootImage]LOG]!><time="16:32:00.963+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="bootimagemgr.cpp:1736">
<![LOG[Set enterpirse certificate in transport]LOG]!><time="16:32:01.008+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:9207">
<![LOG[Set media certificate in transport]LOG]!><time="16:32:01.027+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:9220">
<![LOG[Set authenticator in transport]LOG]!><time="16:32:01.027+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:7592">
<![LOG[Set authenticator in transport]LOG]!><time="16:32:01.084+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:7592">
<![LOG[Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="16777218" ServerName="" ServerRemoteName=""><Machine><ClientID/><NetbiosName/></Machine></Identification><PXEBootAction LastPXEAdvertisementID=""
LastPXEAdvertisementTime="" OfferID="" OfferIDTime="" PkgID="" PackageVersion="" PackagePath="" BootImageID="" Mandatory=""/></ClientIDReply>
]LOG]!><time="16:32:01.108+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:6402">
<![LOG[Client Identity: {C9929C4D-735A-4973-8659-4D3D5D5E4F92}]LOG]!><time="16:32:01.108+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:6428">
<![LOG[Set enterpirse certificate in transport]LOG]!><time="16:32:01.151+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:9207">
<![LOG[Set media certificate in transport]LOG]!><time="16:32:01.174+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:9220">
<![LOG[Set authenticator in transport]LOG]!><time="16:32:01.174+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:7592">
<![LOG[Set authenticator in transport]LOG]!><time="16:32:01.209+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:7592">
<![LOG[PXE::CBootImageManager::FindMatchingArchitectureBootImage]LOG]!><time="16:32:05.230+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="bootimagemgr.cpp:1736">
<![LOG[Set enterpirse certificate in transport]LOG]!><time="16:32:05.290+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:9207">
<![LOG[Set media certificate in transport]LOG]!><time="16:32:05.325+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:9220">
<![LOG[Set authenticator in transport]LOG]!><time="16:32:05.325+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:7592">
<![LOG[Set authenticator in transport]LOG]!><time="16:32:05.366+240" date="05-06-2012" component="SMSPXE" context="" type="1" thread="3600" file="libsmsmessaging.cpp:7592">
<![LOG[Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="16777218" ServerName="" ServerRemoteName=""><Machine><ClientID/><NetbiosName/></Machine></Identification><PXEBootAction LastPXEAdvertisementID=""
LastPXEAdvertisementTime="" OfferID="" OfferIDTime="" PkgID="" PackageVersion="" PackagePath="" BootImageID="" Mandatory=""/></ClientIDReply>
=============================================================================================
I've been hammering this for about 10 hours now (or to be honest, it's been hammering me) and it must be something very simple I'm missing. I have a feeling that I'm doing something I used to do in 2007 and whatever that is, it does not work in
2012.
If I connect using boot media, Task Sequences execute perfectly.
TIA,
Tom

Option 66: 10.10.0.11
Option 67: smsboot\x86\wdsnbp.com
Pending Request ID: 6
Contacting Server: 10.10.0.11
TFTP Download: smsboot\x64\abortpxe.com
PXE Boot aborted. Booting to next device
<![LOG[Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="16777218" ServerName="" ServerRemoteName=""><Machine><ClientID/><NetbiosName/></Machine></Identification><PXEBootAction
LastPXEAdvertisementID="" LastPXEAdvertisementTime="" OfferID="" OfferIDTime="" PkgID="" PackageVersion="" PackagePath="" BootImageID="" Mandatory=""/></ClientIDReply>
Those options are fine when using DHCP options. They must be configured right because ConfigMgr does send a reply to the client ("abortpxe"). It basically tells you that ConfigMgr knows the MAC address and/or SMBIOSGUID of the client, but cannot find
a deployment for it.
Just find ResourceID 16777218 in the console (you might have to add the ResourceID column) and double check if there's an deployment available (properties of the client with resourceID 16777218).
Torsten Meringer | http://www.mssccmfaq.de
Your answer really helped me. I was searching for 2 days trying to find a computer in Config Manager. Your suggestion to "Just
find ResourceID 16777218 in the console (you might have to add the ResourceID column) and double check if there" was the trick to finding the computer in Config Manager. Thanks for all of your help
Gregory Campbell System Administrator

SCCM 2012 pxe boot issue

My test machines cannot PXE boot.
My lab environment is very simple:
10.10.0.0/24 subnet
10.10.0.5 = Server2012, DHCP, DNS, SQL Server 2008 R2 Sp2
10.10.0.7 = Server2012, SCCM2012
All machines are Oracle VM Box virtual machines connecting through the same virtual network.
Setup the PXE service from DP properties. I let SCCM install WDS. WDS in Server
Manager does not have a server node, but the WDS service is running. DP PXE tab is configured as follows:
"Enable PXE support for clients" is checked
"Allow this distribution point to respond to incoming PXE requests" is checked
"Enable unknown computer support" is checked
"Require a password when computers use PXE" is not checked
"User device affinity" is set to "Allow user device affinity with automatic approval"
PXE is configured to respond on all network interfaces
The PXE server response delay is 0 seconds
The DHCP server has options configured as follows:
Option 66: 10.10.0.7
Option 67: smsboot\x86\wdsnbp.com
Both DP and MP on SCCM server are configured for HTTP.
Both x86 and x64 boot images have been distributed to DP. The media was updated after
PXE was enabled on the DP.
Both x86 and x64 boot images have "Deploy this image from the PXE service point" enabled on the Data Source tab of their properties
SMSPXE.Log
<![LOG[Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="16777219" ServerName=""><Machine><ClientID/><NetbiosName/></Machine></Identification><PXEBootAction
LastPXEAdvertisementID="" LastPXEAdvertisementTime="" OfferID="" OfferIDTime="" PkgID="" PackageVersion="" PackagePath="" BootImageID="" Mandatory=""/></ClientIDReply>
]LOG]!><time="15:05:09.346-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592" file="libsmsmessaging.cpp:6544">
<![LOG[08:00:27:61:59:79, BF2ACCDD-1455-E149-963C-9A845B9C111E: no advertisements found]LOG]!><time="15:05:09.346-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592"
file="database.cpp:483">
<![LOG[08:00:27:61:59:79, BF2ACCDD-1455-E149-963C-9A845B9C111E: No boot action. Aborted.]LOG]!><time="15:05:09.441-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592"
file="database.cpp:483">
<![LOG[08:00:27:61:59:79, BF2ACCDD-1455-E149-963C-9A845B9C111E: Not serviced.]LOG]!><time="15:05:09.441-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592" file="database.cpp:483">
<![LOG[Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="16777219" ServerName=""><Machine><ClientID/><NetbiosName/></Machine></Identification><PXEBootAction
LastPXEAdvertisementID="" LastPXEAdvertisementTime="" OfferID="" OfferIDTime="" PkgID="" PackageVersion="" PackagePath="" BootImageID="" Mandatory=""/></ClientIDReply>
]LOG]!><time="15:05:09.705-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592" file="libsmsmessaging.cpp:6544">
<![LOG[08:00:27:61:59:79, BF2ACCDD-1455-E149-963C-9A845B9C111E: no advertisements found]LOG]!><time="15:05:09.705-330" date="07-07-2014" component="SMSPXE" context="" type="1" thread="13592"
file="database.cpp:483">

Resource ID is already present in the Unknown Computer (Windows 7) Properties please look into it and
OSD Task Sequences is there :(.

Installing Windows 7, 8 and 8.1 using ISOs, Answer Files and Driver files over PXE boot

I have a validation lab that uses Windows 7, 8 and 8.1 on several completely different systems. I am looking for an easy way for the techs to PXE boot from a 2012 Server, select the OS to install and have the OS installed with drivers so when they come back
to the system it has the OS installed with no Bangs in Device Manager.
I have done this in the past (7-8 years ago) and it was fairly easy. Now from what I read it appears I have to create "Image" files for each system type? I hope I am misreading this because that method is counter-productive to create 10 different
images for 10 different systems.
I thought I used WDS and AIK on a 2K3 Server but I don't remember.
Is there a method/tool to install the operating systems as I described above using original OS ISOs, unattended answer files and driver files? WDS or SCCM? AM I misreading how it works?

Consider using newer Windows ADK
http://www.microsoft.com/en-us/download/details.aspx?id=39982

Screen resolution when PXE boot from WDS vs Install Windows 8.1 from USB

Hi all
I own a Lenovo ThinkPad T430s, X230 Tablet, and now have my hands on a T440. All three machines have UEFI Secure Boot enabled properly, i.e. Windows boot screen shows Lenovo logo instead of Windows logo.
However, if I do a PXE boot (using Windows Deployment Services from Windows Server 2012, not R2) and boot to the same boot.wim provided on a Windows 8.1 ISO image, the boot screen resolution turns crap, and the WinPE environment runs in 640x480. Also, as opposed
to the Lenovo logo showing on the boot screen, the Windows logo shows up instead, indicating it's not doing a secure boot?
When booting from a USB stick however, using the same Windows 8.1 boot.wim (copied from ISO), the screen resolution in Windows Setup is detected correctly, and the Lenovo logo shows up.
This occurs on all three machines since MDT was upgraded to MDT 2013 or when I replaced Windows 8 boot.wim with Windows 8.1 boot.wim (as the Windows ADK 8 --> ADK 8.1).
Is there a fix for this? Do others have the same problem elsewhere?
Many thanks

Hi,
When boot UEFI-based computer from PXE you should take more into consideration.
For some computers, you might have to perform additional steps to make sure that Windows is installed in UEFI mode, and not in legacy BIOS-compatibility mode.
Some computers might support UEFI. However, they do not support a PXE-initiated boot when in UEFI mode.
How to Create a PXE-Initiated Windows 8 Deployment for UEFI-Based or BIOS-Based Computers in Configuration Manager
http://technet.microsoft.com/en-us/library/jj938037.aspx
Especially for “Pre-Deployment Considerations”
If you still cannot find a way to make it boot from UEFI mode, you should contact with manufacture to confirm if PXE-initiated boot is supported.
Hope this helps.

Can't PXE boot Windows 8 models

We load the PCs with our own OS image as they come in. The process works off a PXE (network) boot image.
We recently started ording the same X230s, only with a Windows 8 license. Lenovo indicated that there should be no changes needed with our image.
However, we can not PXE boot these machines. We shut them down and bring them back up with an F12 on the bios splash screen and select PCI LAN.
We get a message saying >>Start PXE over IPv4
It hangs there a while, then tries IPv6, then goes back to the boot device ment.
We got a solid green and a flashing yellow light on the network connector. And we've PXE booted off of this connection many, many times
What are we missing?
Thank you.
Solved!
Go to Solution.

Hey there DOTJKO,
I've seen over on another thread, that they were having the same issue. They were able to get the PXE Boot process to finally go by:
1) Go to BIOS
2) SECURITY tab --> Secure Boot --> set SECURE BOOT to [DISABLED]
3) Go to STARTUP tab --> UEFI/Legacy Boot --> set to [BOTH]
Hopefully this assists you in getting those X230s loaded up with your image. Good Luck, and keep us posted on your progress.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

X1 Carbon (20A7) wont pxe boot

Similar Messages

Maybe you are looking for