Xinerama/Nvidia configuration difficulties...Help!
I'm having difficulties setting up Xorg to Xinerama across both of my monitors. I'm running Arch Linux witih kernel 2.6.7, fluxbox and two Nvidia video cards (Geforce 5200 AGP and Geforce2 MX 400 PCI). P4 2.4, 1 Gig of RAM...What else? I'm posting my /etc/X11/xorg.conf file below.
When I startx, there's a screen flicker on my main monitor, then nothing shows up at all, and I have to press the reset button.
This happens when I try to use the second screen as the main (and only) screen as well.
I've looked through the Xorg logs. There is a line that says "(WW) NVIDIA: No matching Device section for instace (BusID PCI:2:5:0) found".
I think I have a device section for the GPU?
I still startx with "startx -- +xinerama". Is this necessary even though I have "Option 'xinerama' 'true'"???
I could post any additional info requested if seomeone would be kind enough to help me.
Thanks very much.
Section "Module"
Load "dbe" # Double buffer extension
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "type1"
Load "speedo"
Load "freetype"
EndSection
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/artwiz-fonts/"
FontPAth "/usr/X11R6/lib/X11/fonts/TTF/"
EndSection
Section "ServerFlags"
Option "Xinerama" "True"
EndSection
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
Option "AutoRepeat" "500 30"
Option "XkbRules" "xorg"
Option "XkbModel" "pc101"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/psaux"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons"
EndSection
Section "Monitor"
Identifier "Monitor0"
HorizSync 30-95
VertRefresh 50-160
EndSection
Section "Monitor"
Identifier "Monitor1"
HorizSync 30-69
VertRefresh 50-120
EndSection
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
Driver "vga"
EndSection
Section "Device"
Identifier "VideoCard0"
Driver "nvidia"
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "VideoCard1"
Driver "nvidia"
BusID "PCI:2:5:0"
EndSection
Section "Screen"
Identifier "Screen 1"
Device "VideoCard0"
Monitor "Monitor0"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1280x960" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1280x960" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1280x960" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection
Section "Screen"
Identifier "Screen 2"
Device "VideoCard1"
Monitor "Monitor1"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection
Section "ServerLayout"
Identifier "Simple Layout"
Screen 0 "Screen 1" 0 0
Screen 1 "Screen 2" Rightof "Screen 1"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
Also, if I comment out the "Screen 1 'Screen 2' Rightof 'Screen 1'" Line, the display works fine on my main monitor.
I added the part about:
I've looked through the Xorg logs. There is a line that says "(WW) NVIDIA: No matching Device section for instace (BusID PCI:2:5:0) found".
Similar Messages
-
Hi,
I want to configure online help for my SAP GUI. It is Netweaver 7.0. Can anybody provide me any inputs on this?
Regards,
SrideviHi, I too do not have any Library file installed in my SAP Server, because when I click on Help in GUI and then click on SAP Library, it shows No documentation available.
So I had went through your given following steps, but still I am getting the same error
Login into SAP system (DEV) with user having auths as sap*/DDIC in client 000 or production client
Client should be Open
Run transaction SR13
PlainHtmlHttp TAB selected
Clicked on "New Entries"
Variant: SAP_HELP
Platform: WINDOWS NT (My OS is windows2k8 64bit)
Area: IWBHELP
server names: http://help.sap.com
path:
(Mymachine)\saphelp_nw70\helpdata
language:EN
default: put it check marked
Clicked on Save button
then ceated new request called SAP_Help
Then clicked on Save button
Then clicked on back button
and then Clicked on Help -> SAP Library
But still is says No Documentation Available
Please guide. I would appreciate your help
Thanks & Regards,
Prashant -
I bought an HP ENVY TouchSmart 15-j013ea about 6 months ago and I have had a major problem with the graphics that I cannot seem to solve. I think it started when I updated to Windows 8.1, even though I am not 100% certain.
I have noticed the following three problems, and I think they are related:
Some windows (such as Chrome, Skype, or even Device Manager or other windows) are very blurry compared to others.
The firefox menu window has some deformed black arrows instead of the normal ones.
When playing a game (specifically, Star Wars the Force Unleashed 2), after a while I get an error that the computer has ran out of memory. However, according to task manager, only about 50% is in use, not to mention that I have 8 GB of RAM + 2 GB graphics memory. At the same time, the computer gets rather loud (like a fan working overtime) and hot.
The laptop has both Intel and NVidia graphics, and both are enabled in Device Manager. To be honest, I have no idea which is used when, or how to check that (let me know if there is a way)
I have tried the following without success:
Uninstalling the Intel graphics driver from device manager and installing a version I downloaded from the HP website for my laptop and OS. After that, Windows would NOT BOOT, and I had to do a system restore.
Uninstalling the Intel graphics from Programs and Features, and installing 2 different versions from the Intel website. Nothing changed.
Updating Nvidia driver through GeForce Experience. Nothing changed.
Updating Intel drivers from Windows Update. Nothing changed.
Quite frankly I am not sure what the problem could be, since the graphics versions are supposed to be compatible with WIndows 8.1. I also don't get why some windows are blurry and others are not. I am thinking the computer uses only the Intel graphics and not the Nvidia (at least in the blurry windows), but even if that was the case (and it shouldn't be), I don't think I should be having this problem.
At this point, I really need help. My graphics details are:
Intel HD Graphics 4600: Driver version: 10.18.10.3412
NVidia GeForce GT 740M: Driver version: 335.23
NVidia GeForce Experience version: 1.8.2
I am attaching screenshots that show driver details and the problems.
Thank you.
Blurry Chrome:
Firefox menu problem:
Device Manager and driver windows are also blurry, both graphics are shownI had a similar problem with a Dell laptop. I found the problem was the laptop wanted to switch between the Intel and NYIDIA video cards. It would switch to the Intel when high graphics was not required then to the NIVIDIA when high graphics was required. The laptop does this to save power when high graphics is not required but it caused problems with some applications, specifically high graphics games.
For me the solution was to disable the Intel graphics processor. You can do this by right clicking on your Wallpaper, select the NIVIDIA Control Panel, then select Set Physx Configuration. You will see a dropdown box labeled Select Physx Processor. It is set to Auto by default. This allows the switching I described. Select this dropdown box and select your NIVIDIA processor. This will prevent the laptop from switching and force it to use your NVIDIA processor exclusively.
Hope this helps.
Sacto Fred
Owner and CEO
H&O PC Soultions -
Bumblebee configuration - need help
Recently I bought notebook with NVIDIA Optimus technology, and i'm stuck in bumblebee installation.
optirun -vv glxgears:
[ 175.078111] [DEBUG]Reading file: /etc/bumblebee/bumblebee.conf
[ 175.078715] [INFO]Configured driver: nvidia
[ 175.257402] [DEBUG]optirun version 3.0.1 starting...
[ 175.257459] [DEBUG]Active configuration:
[ 175.257474] [DEBUG] bumblebeed config file: /etc/bumblebee/bumblebee.conf
[ 175.257487] [DEBUG] X display: :8
[ 175.257498] [DEBUG] LD_LIBRARY_PATH: /usr/lib/nvidia-bumblebee:/usr/lib32/nvidia-bumblebee
[ 175.257510] [DEBUG] Socket path: /var/run/bumblebee.socket
[ 175.257520] [DEBUG] VGL Compression: proxy
[ 178.550730] [INFO]Response: No - error: X did not start properly
[ 178.550800] [ERROR]Cannot access secondary GPU - error: X did not start properly
[ 178.550813] [DEBUG]Socket closed.
[ 178.550842] [ERROR]Aborting because fallback start is disabled.
[ 178.550846] [DEBUG]Killing all remaining processes.
After [DEBUG] VGL Compression:proxy I get thrown into tty console with X process failure. After couple of Ctrl-Alt-F1/F7 state returns back to graphical interface and I see the rest of the message.
Xorg.8.log:
[ 175.934]
X.Org X Server 1.12.4
Release Date: 2012-08-27
[ 175.934] X Protocol Version 11, Revision 0
[ 175.934] Build Operating System: Linux 3.4.8-1-ARCH x86_64
[ 175.934] Current Operating System: Linux jediknight-comp 3.4.9-1-ARCH #1 SMP PREEMPT Wed Aug 15 18:59:31 CEST 2012 x86_64
[ 175.934] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=1e8827f3-dea2-496c-b3e4-5b9c67c7c5bc ro quiet
[ 175.934] Build Date: 27 August 2012 08:04:39AM
[ 175.934]
[ 175.934] Current version of pixman: 0.26.2
[ 175.934] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 175.934] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 175.934] (==) Log file: "/var/log/Xorg.8.log", Time: Wed Aug 29 15:27:45 2012
[ 175.934] (++) Using config file: "/etc/bumblebee/xorg.conf.nvidia"
[ 175.934] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 175.949] (==) ServerLayout "Layout0"
[ 175.949] (==) No screen section available. Using defaults.
[ 175.949] (**) |-->Screen "Default Screen Section" (0)
[ 175.949] (**) | |-->Monitor "<default monitor>"
[ 175.949] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 175.949] (**) | |-->Device "Device1"
[ 175.949] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 175.949] (**) Option "AutoAddDevices" "false"
[ 175.949] (**) Not automatically adding devices
[ 175.949] (==) Automatically enabling devices
[ 175.949] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 175.949] Entry deleted from font path.
[ 175.949] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 175.949] Entry deleted from font path.
[ 175.949] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 175.949] Entry deleted from font path.
[ 175.949] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 175.950] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 175.950] Entry deleted from font path.
[ 175.950] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 175.950] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 175.950] (++) ModulePath set to "/usr/lib/nvidia-bumblebee/xorg/,/usr/lib/xorg/modules"
[ 175.950] (==) |-->Input Device "<default pointer>"
[ 175.950] (==) |-->Input Device "<default keyboard>"
[ 175.950] (==) The core pointer device wasn't specified explicitly in the layout.
Using the default mouse configuration.
[ 175.950] (==) The core keyboard device wasn't specified explicitly in the layout.
Using the default keyboard configuration.
[ 175.950] (II) Loader magic: 0x7c8b00
[ 175.950] (II) Module ABI versions:
[ 175.950] X.Org ANSI C Emulation: 0.4
[ 175.950] X.Org Video Driver: 12.1
[ 175.950] X.Org XInput driver : 16.0
[ 175.950] X.Org Server Extension : 6.0
[ 175.950] (--) PCI:*(0:1:0:0) 10de:1051:144d:c0b6 rev 161, Mem @ 0xe0000000/16777216, 0xb0000000/268435456, 0xc0000000/33554432, I/O @ 0x00003000/128
[ 175.950] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 175.950] (II) LoadModule: "extmod"
[ 175.951] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 175.951] (II) Module extmod: vendor="X.Org Foundation"
[ 175.951] compiled for 1.12.4, module version = 1.0.0
[ 175.951] Module class: X.Org Server Extension
[ 175.951] ABI class: X.Org Server Extension, version 6.0
[ 175.951] (II) Loading extension MIT-SCREEN-SAVER
[ 175.951] (II) Loading extension XFree86-VidModeExtension
[ 175.951] (II) Loading extension XFree86-DGA
[ 175.951] (II) Loading extension DPMS
[ 175.951] (II) Loading extension XVideo
[ 175.951] (II) Loading extension XVideo-MotionCompensation
[ 175.951] (II) Loading extension X-Resource
[ 175.951] (II) LoadModule: "dbe"
[ 175.951] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 175.951] (II) Module dbe: vendor="X.Org Foundation"
[ 175.951] compiled for 1.12.4, module version = 1.0.0
[ 175.951] Module class: X.Org Server Extension
[ 175.951] ABI class: X.Org Server Extension, version 6.0
[ 175.951] (II) Loading extension DOUBLE-BUFFER
[ 175.951] (II) LoadModule: "glx"
[ 175.951] (II) Loading /usr/lib/nvidia-bumblebee/xorg/modules/extensions/libglx.so
[ 176.815] (II) Module glx: vendor="NVIDIA Corporation"
[ 176.815] compiled for 4.0.2, module version = 1.0.0
[ 176.815] Module class: X.Org Server Extension
[ 176.815] (II) NVIDIA GLX Module 304.37 Wed Aug 8 20:16:03 PDT 2012
[ 176.815] (II) Loading extension GLX
[ 176.815] (II) LoadModule: "record"
[ 176.816] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 176.816] (II) Module record: vendor="X.Org Foundation"
[ 176.816] compiled for 1.12.4, module version = 1.13.0
[ 176.816] Module class: X.Org Server Extension
[ 176.816] ABI class: X.Org Server Extension, version 6.0
[ 176.816] (II) Loading extension RECORD
[ 176.816] (II) LoadModule: "dri"
[ 176.816] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 176.817] (II) Module dri: vendor="X.Org Foundation"
[ 176.817] compiled for 1.12.4, module version = 1.0.0
[ 176.817] ABI class: X.Org Server Extension, version 6.0
[ 176.817] (II) Loading extension XFree86-DRI
[ 176.817] (II) LoadModule: "dri2"
[ 176.817] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 176.817] (II) Module dri2: vendor="X.Org Foundation"
[ 176.817] compiled for 1.12.4, module version = 1.2.0
[ 176.817] ABI class: X.Org Server Extension, version 6.0
[ 176.817] (II) Loading extension DRI2
[ 176.817] (II) LoadModule: "nvidia"
[ 176.818] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 176.922] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 176.922] compiled for 4.0.2, module version = 1.0.0
[ 176.922] Module class: X.Org Video Driver
[ 176.952] (II) LoadModule: "mouse"
[ 176.953] (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
[ 176.960] (II) Module mouse: vendor="X.Org Foundation"
[ 176.960] compiled for 1.12.3, module version = 1.8.1
[ 176.960] Module class: X.Org XInput Driver
[ 176.960] ABI class: X.Org XInput driver, version 16.0
[ 176.960] (II) LoadModule: "kbd"
[ 176.960] (WW) Warning, couldn't open module kbd
[ 176.960] (II) UnloadModule: "kbd"
[ 176.960] (II) Unloading kbd
[ 176.960] (EE) Failed to load module "kbd" (module does not exist, 0)
[ 176.960] (II) NVIDIA dlloader X Driver 304.37 Wed Aug 8 19:54:47 PDT 2012
[ 176.960] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 176.966] (--) using VT number 7
[ 176.979] (II) Loading sub module "fb"
[ 176.979] (II) LoadModule: "fb"
[ 176.979] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 176.979] (II) Module fb: vendor="X.Org Foundation"
[ 176.979] compiled for 1.12.4, module version = 1.0.0
[ 176.979] ABI class: X.Org ANSI C Emulation, version 0.4
[ 176.979] (II) Loading sub module "wfb"
[ 176.979] (II) LoadModule: "wfb"
[ 176.979] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 176.991] (II) Module wfb: vendor="X.Org Foundation"
[ 176.991] compiled for 1.12.4, module version = 1.0.0
[ 176.991] ABI class: X.Org ANSI C Emulation, version 0.4
[ 176.991] (II) Loading sub module "ramdac"
[ 176.991] (II) LoadModule: "ramdac"
[ 176.991] (II) Module "ramdac" already built-in
[ 177.008] (II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 177.008] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 177.008] (==) NVIDIA(0): RGB weight 888
[ 177.008] (==) NVIDIA(0): Default visual is TrueColor
[ 177.008] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 177.008] (**) NVIDIA(0): Option "NoLogo" "true"
[ 177.008] (**) NVIDIA(0): Option "UseEDID" "false"
[ 177.008] (**) NVIDIA(0): Option "ConnectedMonitor" "CRT-0"
[ 177.008] (**) NVIDIA(0): Enabling 2D acceleration
[ 177.008] (**) NVIDIA(0): ConnectedMonitor string: "CRT-0"
[ 177.008] (**) NVIDIA(0): Ignoring EDIDs
/etc/bumblebee/xorg.conf.nvidia
Section "ServerLayout"
Identifier "Layout0"
Option "AutoAddDevices" "false"
EndSection
Section "Files"
ModulePath "/usr/lib/nvidia-bumblebee,/usr/lib/xorg/modules"
EndSection
Section "Device"
Identifier "Device1"
Driver "nvidia"
VendorName "NVIDIA Corporation"
Option "NoLogo" "true"
Option "UseEDID" "false"
Option "ConnectedMonitor" "CRT-0"
BusID "PCI:01:00:0"
EndSection
/etc/bumblebee/bumblebee.conf
[bumblebeed]
VirtualDisplay=:8
KeepUnusedXServer=false
ServerGroup=bumblebee
TurnCardOffAtExit=false
NoEcoModeOverride=false
Driver=nvidia
[optirun]
VGLTransport=proxy
AllowFallbackToIGC=false
[driver-nvidia]
KernelDriver=nvidia
Module=nvidia
PMMethod=auto
LibraryPath=/usr/lib/nvidia-bumblebee:/usr/lib32/nvidia-bumblebee
XorgModulePath=/usr/lib/nvidia-bumblebee/xorg/,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau
/etc/X11/xorg.conf: empty
What am I doing wrong? Tired of cracking configuration files...I left my ambitions to install proprietary driver behind, and tried to install bumblebee with opensource driver, thinking that everything is going to be fine... But, I got into pretty messy situation again, and i didn't find any useful information on the Internet.
So, i removed blacklist for nouveau module, and all instances of nvidia driver: tools, blob, etc. Then I installed xf86-video-nouveau, nouveau-dri, mesa packages. After that, I configured bumblebee.conf to work with nouveau.
Now i got another error:
[jediknight@jediknight-comp ~]$ optirun -vv glxgears
[ 2912.873563] [DEBUG]Reading file: /etc/bumblebee/bumblebee.conf
[ 2912.874274] [INFO]Configured driver: nouveau
[ 2913.025119] [DEBUG]optirun version 3.0.1 starting...
[ 2913.025225] [DEBUG]Active configuration:
[ 2913.025269] [DEBUG] bumblebeed config file: /etc/bumblebee/bumblebee.conf
[ 2913.025320] [DEBUG] X display: :8
[ 2913.025403] [DEBUG] LD_LIBRARY_PATH:
[ 2913.025483] [DEBUG] Socket path: /var/run/bumblebee.socket
[ 2913.025549] [DEBUG] VGL Compression: proxy
[ 2913.142592] [INFO]Response: No - error: [XORG] (EE) No devices detected.
[ 2913.142700] [ERROR]Cannot access secondary GPU - error: [XORG] (EE) No devices detected.
[ 2913.142762] [DEBUG]Socket closed.
[ 2913.142841] [ERROR]Aborting because fallback start is disabled.
[ 2913.142898] [DEBUG]Killing all remaining processes.
Xorg.8.log:
[jediknight@jediknight-comp ~]$ cat /var/log/Xorg.8.log
[ 3458.807]
X.Org X Server 1.12.4
Release Date: 2012-08-27
[ 3458.807] X Protocol Version 11, Revision 0
[ 3458.807] Build Operating System: Linux 3.4.8-1-ARCH x86_64
[ 3458.807] Current Operating System: Linux jediknight-comp 3.5.3-1-ARCH #1 SMP PREEMPT Sun Aug 26 09:14:51 CEST 2012 x86_64
[ 3458.807] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=1e8827f3-dea2-496c-b3e4-5b9c67c7c5bc ro quiet
[ 3458.807] Build Date: 27 August 2012 08:04:39AM
[ 3458.807]
[ 3458.807] Current version of pixman: 0.26.2
[ 3458.807] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 3458.807] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 3458.808] (==) Log file: "/var/log/Xorg.8.log", Time: Sun Sep 2 17:58:40 2012
[ 3458.808] (++) Using config file: "/etc/bumblebee/xorg.conf.nouveau"
[ 3458.808] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 3458.808] (==) ServerLayout "Layout0"
[ 3458.808] (**) |-->Screen "Screen0" (0)
[ 3458.808] (**) | |-->Monitor "<default monitor>"
[ 3458.808] (**) | |-->Device "Device0"
[ 3458.808] (==) No monitor specified for screen "Screen0".
Using a default monitor configuration.
[ 3458.808] (**) Option "AutoAddDevices" "false"
[ 3458.809] (**) Not automatically adding devices
[ 3458.809] (==) Automatically enabling devices
[ 3458.809] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 3458.809] Entry deleted from font path.
[ 3458.809] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 3458.809] Entry deleted from font path.
[ 3458.809] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 3458.809] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 3458.809] Entry deleted from font path.
[ 3458.809] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 3458.809] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 3458.809] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 3458.809] (==) |-->Input Device "<default pointer>"
[ 3458.809] (==) |-->Input Device "<default keyboard>"
[ 3458.809] (==) The core pointer device wasn't specified explicitly in the layout.
Using the default mouse configuration.
[ 3458.809] (==) The core keyboard device wasn't specified explicitly in the layout.
Using the default keyboard configuration.
[ 3458.809] (II) Loader magic: 0x7c8b00
[ 3458.809] (II) Module ABI versions:
[ 3458.809] X.Org ANSI C Emulation: 0.4
[ 3458.809] X.Org Video Driver: 12.1
[ 3458.809] X.Org XInput driver : 16.0
[ 3458.809] X.Org Server Extension : 6.0
[ 3458.810] (--) PCI:*(0:1:0:0) 10de:1051:144d:c0b6 rev 161, Mem @ 0xe0000000/16777216, 0xb0000000/268435456, 0xc0000000/33554432, I/O @ 0x00003000/128
[ 3458.811] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 3458.811] (II) LoadModule: "extmod"
[ 3458.811] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 3458.811] (II) Module extmod: vendor="X.Org Foundation"
[ 3458.811] compiled for 1.12.4, module version = 1.0.0
[ 3458.811] Module class: X.Org Server Extension
[ 3458.811] ABI class: X.Org Server Extension, version 6.0
[ 3458.811] (II) Loading extension MIT-SCREEN-SAVER
[ 3458.811] (II) Loading extension XFree86-VidModeExtension
[ 3458.811] (II) Loading extension XFree86-DGA
[ 3458.811] (II) Loading extension DPMS
[ 3458.812] (II) Loading extension XVideo
[ 3458.812] (II) Loading extension XVideo-MotionCompensation
[ 3458.812] (II) Loading extension X-Resource
[ 3458.812] (II) LoadModule: "dbe"
[ 3458.812] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 3458.812] (II) Module dbe: vendor="X.Org Foundation"
[ 3458.812] compiled for 1.12.4, module version = 1.0.0
[ 3458.812] Module class: X.Org Server Extension
[ 3458.812] ABI class: X.Org Server Extension, version 6.0
[ 3458.812] (II) Loading extension DOUBLE-BUFFER
[ 3458.812] (II) LoadModule: "glx"
[ 3458.812] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 3458.812] (II) Module glx: vendor="X.Org Foundation"
[ 3458.812] compiled for 1.12.4, module version = 1.0.0
[ 3458.812] ABI class: X.Org Server Extension, version 6.0
[ 3458.812] (==) AIGLX enabled
[ 3458.812] (II) Loading extension GLX
[ 3458.813] (II) LoadModule: "record"
[ 3458.813] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 3458.813] (II) Module record: vendor="X.Org Foundation"
[ 3458.813] compiled for 1.12.4, module version = 1.13.0
[ 3458.813] Module class: X.Org Server Extension
[ 3458.813] ABI class: X.Org Server Extension, version 6.0
[ 3458.813] (II) Loading extension RECORD
[ 3458.813] (II) LoadModule: "dri"
[ 3458.813] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 3458.813] (II) Module dri: vendor="X.Org Foundation"
[ 3458.813] compiled for 1.12.4, module version = 1.0.0
[ 3458.813] ABI class: X.Org Server Extension, version 6.0
[ 3458.813] (II) Loading extension XFree86-DRI
[ 3458.814] (II) LoadModule: "dri2"
[ 3458.814] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 3458.814] (II) Module dri2: vendor="X.Org Foundation"
[ 3458.814] compiled for 1.12.4, module version = 1.2.0
[ 3458.814] ABI class: X.Org Server Extension, version 6.0
[ 3458.814] (II) Loading extension DRI2
[ 3458.814] (II) LoadModule: "nouveau"
[ 3458.814] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 3458.814] (II) Module nouveau: vendor="X.Org Foundation"
[ 3458.814] compiled for 1.12.2, module version = 1.0.1
[ 3458.814] Module class: X.Org Video Driver
[ 3458.814] ABI class: X.Org Video Driver, version 12.0
[ 3458.814] (II) LoadModule: "mouse"
[ 3458.815] (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
[ 3458.815] (II) Module mouse: vendor="X.Org Foundation"
[ 3458.815] compiled for 1.12.3, module version = 1.8.1
[ 3458.815] Module class: X.Org XInput Driver
[ 3458.815] ABI class: X.Org XInput driver, version 16.0
[ 3458.815] (II) LoadModule: "kbd"
[ 3458.815] (WW) Warning, couldn't open module kbd
[ 3458.815] (II) UnloadModule: "kbd"
[ 3458.815] (II) Unloading kbd
[ 3458.816] (EE) Failed to load module "kbd" (module does not exist, 0)
[ 3458.816] (II) NOUVEAU driver
[ 3458.816] (II) NOUVEAU driver for NVIDIA chipset families :
[ 3458.816] RIVA TNT (NV04)
[ 3458.816] RIVA TNT2 (NV05)
[ 3458.816] GeForce 256 (NV10)
[ 3458.816] GeForce 2 (NV11, NV15)
[ 3458.816] GeForce 4MX (NV17, NV18)
[ 3458.816] GeForce 3 (NV20)
[ 3458.816] GeForce 4Ti (NV25, NV28)
[ 3458.816] GeForce FX (NV3x)
[ 3458.816] GeForce 6 (NV4x)
[ 3458.816] GeForce 7 (G7x)
[ 3458.816] GeForce 8 (G8x)
[ 3458.816] GeForce GTX 200 (NVA0)
[ 3458.816] GeForce GTX 400 (NVC0)
[ 3458.816] (--) using VT number 7
[ 3458.816] (EE) No devices detected.
[ 3458.816]
Fatal server error:
[ 3458.816] no screens found
[ 3458.816]
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 3458.816] Please also check the log file at "/var/log/Xorg.8.log" for additional information.
[ 3458.816]
Devices are online:
[jediknight@jediknight-comp ~]$ lspci|grep VGA
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
[jediknight@jediknight-comp ~]$ lspci|grep 3D
01:00.0 3D controller: NVIDIA Corporation GF119 [GeForce GT 520MX] (rev a1)
After that, i noticed strange message during boot time, telling that VBIOS image not found.
dmesg:
[jediknight@jediknight-comp ~]$ dmesg|grep drm
[ 1.263009] [drm] Initialized drm 1.1.0 20060810
[ 1.267833] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 1.293316] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 1.293318] [drm] Driver supports precise vblank timestamp query.
[ 2.035641] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 2.170467] fbcon: inteldrmfb (fb0) is primary device
[ 2.426027] fb0: inteldrmfb frame buffer device
[ 2.426028] drm: registered panic notifier
[ 2.428364] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 2.432322] [drm] nouveau 0000:01:00.0: Detected an NVd0 generation card (0x0d9110a1)
[ 2.433051] [drm] nouveau 0000:01:00.0: acceleration disabled by default, pass noaccel=0 to force enable
[ 2.435870] [drm] nouveau 0000:01:00.0: Checking PRAMIN for VBIOS
[ 2.483929] [drm] nouveau 0000:01:00.0: ... BIOS signature not found
[ 2.483931] [drm] nouveau 0000:01:00.0: Checking PROM for VBIOS
[ 2.483996] [drm] nouveau 0000:01:00.0: ... BIOS signature not found
[ 2.483997] [drm] nouveau 0000:01:00.0: Checking ACPI for VBIOS
[ 2.483998] [drm] nouveau 0000:01:00.0: ... BIOS signature not found
[ 2.483999] [drm] nouveau 0000:01:00.0: Checking PCIROM for VBIOS
[ 2.484000] [drm] nouveau 0000:01:00.0: ... BIOS signature not found
[ 2.484001] [drm] nouveau 0000:01:00.0: No valid VBIOS image found
1. Why does it happen?
2. How to fix it?
Last edited by JediKnight (2012-09-02 14:34:30) -
Cisco ASA 5505 Configurations. Help... Beyond Frustrated
Hello All,
I'm fairly new to Cisco products and Network management in general. At my place of employment, I was hired as an IT Tech- Repair and Building computers, most aspects of Physical networking, and software refresh/upgrades as well as solving compatibility issues among a plethora of other things. I've configured APs, a couple Catalyst switches, a router or two, and that is about the breadth of my Cisco knowledge. I was kind of thrown into a project which is to update the current inventory of computers which all run Windows XP Professional. We are making a capital purchase of 20 Laptops and 40 Desktops all of which will run Windows 7. This means the outdated PIX they were using is now useless. I purchased a Cisco ASA 5505 (Version 8.2(1)) because it is compatible with Windows XP and Windows 7. I have spent several days and sleepless nights trying to figure out how to configure this thing. I was hoping to use SSL for the VPN. I did some basic configurations just to get started but like I said, I have no real experience with Adaptive Security Appliances and I am so frustrated right now. I tried using the Wizard to no avail. I did a write erase using CLI and tried to configure that way but I'm doing something wrong as far as I can tell. The configurations were mostly pulled from here, the Cisco Community, and a couple other web sites.
I’m connecting the ASA 5505 to a cable modem (gateway 24.39.245.33) and to our Netvanta for VPN purposes. Here are the commands/what I have configured so far:
hostname AMDASA
domain-name asa.(mydomain).com
enable password (encrypted)
passwd (encrypted)
interface Ethernet0/0
description TWCoutside
switchport access vlan 2
no shutdown
write mem
exit
interface Ethernet0/1
description Port1inside
switchport access vlan 1
no shutdown
write mem
exit
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.250 255.255.255.0
write mem
exit
interface Vlan2
nameif outside
security-level 0
ip address 24.39.245.36 255.255.255.240
write mem
exit
object-group icmp-type DefaultICMP
description Default ICMP Types permitted
icmp-object echo-reply
icmp-object unreachable
icmp-object time-exceeded
write mem
exit
ftp mode passive
write mem
clock timezone EST -5
clock summer-time EDT recurring
write mem
exit
dns server-group DefaultDNS
domain-name asa.adcmotors.com
write mem
exit
access-list acl_outside extended permit icmp any any object-group DefaultICMP
access-group acl_outside in interface outside
access-list acl_inside extended permit icmp any any object-group DefaultICMP
access-group acl_inside in interface inside
write mem
exit
write mem
That is the extent of the configurations I made via CLI. I don't know how to set the DNS lookup from a static port and I have no idea what else I'm supposed to do after the above configurations I have done. Is there a place to actually obtain ALL of the configurations needed to VPN in? Is there an easier way to make this thing work? I've seriously grown a patch of gray hair because of this device. Please help me if you can!!!!!!Hi our desperate friend .
First I would suggest to use the Cisco VPN client instead of SSL VPN (AnyConnect). The configuration is a bit simpler and for the SSL VPN you would need to install the client on the ASA and purchase additional license if you plan to have more than 2 clients. The VPN Client usually comes with the ASA. If you dont have it or dont have access to download it from cisco.com go to the person from which you purchased your ASA and ask him how to get it.
That said, I also think that your ASA lacks of some basic configuration as of now. If you are planning to use this in replacement for your current PIX. You would need to configure a default route and some basic NAT:
route outside 0.0.0.0 0.0.0.0 24.39.245.33
global (outside) 1 interface
nat (inside) 1 192.168.0.0 255.255.255.0
Now regarding the VPN Client configuration you would need to something like this:
Create an isakmp policy:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
Create a couple of ACLs that we will use later:
access-list nonat permit ip 192.168.0.0 255.255.255.0 192.168.100.0 255.255.255.0
access-list split_tun standard permit 192.168.0.0 255.255.255.0
Create a Pool for the VPN Clients to use:
ip local pool TestPool 192.168.100.1-192.168.100.20 mask 255.255.255.0
Create a Group Policy:
group-policy TEST internal
group-policy TEST attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split_tun
Create a group:
tunnel-group TEST type ipsec-ra
tunnel-group TEST general-attributes
address-pool TestPool
authentication-server-group ABTVPN
default-group-policy TEST
tunnel-group TEST ipsec-attributes
pre-shared-key cisco123
Create crypto map and do a NAT 0:
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map Outside_dyn_map 10 set transform-set ESP-3DES-SHA
crypto map Outside_map 10 ipsec-isakmp dynamic Outside_dyn_map
crypto map Outside_map interface outside
nat (inside) 0 access-l nonat
Finally create a user that you will use to connect:
username test password test123
Then you would need to configure your VPN Client to connect with the ASA.
Here is a config Example of VPN clients to the ASA. It uses an external server for the authentication but just skip those parts. For the initial config you might want to keep the authentication local.
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806de37e.shtml
I hope this helps. Feel free to ask if you have any questions. Also it would very usefull if you could upload the current config (show run) of the ASA in case you need to ask something else.
Have fun.
Raga -
8 devices, one account, iTunes being difficult - help?
OK, here goes:
We have two MacBook Pros, two iPhone3G, one iPhone 3GS, one iPhone 4S, an iPod Nano (1st gen) and an AppleTV (1st Gen).
Home network is on a Time Capsule (3rd Gen), which has USB connections for drives/printers/etc. I have two USB drives available to use.
The laptops are our main computers, used for everything including entertainment.
The 3G phones are used as iPod Touches by the kids (little kids, no phone service for them yet).
The 3GS is my active phone and the 4S is my wife's.
iTunes is kept updated to current versions: with 10,000 or so songs, 120 movies, many TV shows, many podcasts... etc etc.
We originally had two iTunes accounts, one mine, one my wife's. A long time back before even adding the 4G and 3GS into this mix, we abandoned using my wife's account because iTunes will not let HER listen to what I buy, and vice versa, becuase of the idiotic rules of purchase/licencing. So we have been just using my account for a long time. We have also been forced to sync the AppleTV to my laptop.
All this adds up to my laptop having to 'host' all the data for all the devices, which must all sync with it. This is a huge pain in my a*s, takes up a lot of my disk storage, and it seems dumb as dirt that we must use such an awkward method to use all of our devices.
Please note: I AM NOT GOING TO PAY TO USE 'THE CLOUD'. I have plenty of storage space of my own, thanks, and I don't need to pay subscription fees just to do what I can already do remotely - get to my data at home from elsewhere....
So here's what I hope to find out here in the support community:
Based on the equipment listed, and assuming I can manage configuring stuff (or will ask how),
1) Can I put the iTunes 'library' and data (the actual files) on a USB drive attached to the Time Capsule? {If Y goto A, if N goto 2.}
A) If yes to (1), can I then use iTunes from BOTH laptops and access this SINGLE library (assuming they both use the same iTunes account info)?
B) If yes to (1), can each laptop sync whatever device it wants to?
C) Can the AppleTV be told to sync itself to the library without iTunes running on a laptop? (Don't care if I need to hack it to do this, warranty is over)
2) If I cannot put the library and the files on a remote drive, HOW THE **** can I achieve this sort of functionality:
Access one library and one set of files from both laptops, sync any device from either laptop.
(Access WITHOUT having to have BOTH laptops on the same network, 'awake', and running iTunes)
BTW - "Home Sharing" does not seem to let me do anything more than "see" my library from my wife's laptop - useless for our needs unlessI'm missing something there. Seems to be set up for letting to teens access each others music.Nixt wrote:
1) Can I put the iTunes 'library' and data (the actual files) on a USB drive attached to the Time Capsule? {If Y goto A, if N goto 2.}
Yes.
Nixt wrote:
A) If yes to (1), can I then use iTunes from BOTH laptops and access this SINGLE library (assuming they both use the same iTunes account info)?
Yes, but... the two iTunes will not necessarily automatically stay in sync. If music is added to the iTunes library of one computer that same music will need to be manually added to the iTunes library of the other computer. However you may be able find some scripts at Doug's AppleScripts to help keep things up to date.
Nixt wrote:
B) If yes to (1), can each laptop sync whatever device it wants to?
No. iOS devices and iPods can only be synced with one computer at a time. However one computer can sync to an unlimited number of iOS devices or iPods.
Nixt wrote:
C) Can the AppleTV be told to sync itself to the library without iTunes running on a laptop? (Don't care if I need to hack it to do this, warranty is over)
No. iTunes must be running for the ATV to sync.
You might want to think about getting a refurbished Mac Mini and making it your central media server. That would dramatically simplify your setup. -
Problem with Design Console configuration - please help
Dear All,
I am trying to configure design console. It is installed on Windows XP and should point to remote server. I am getting the following error on OIM Server and Port screen:
INST-07057: Error in validating the Hostname field value. Entered host is not up and running
Make sure that the host is up and running
But host is up and running. I can ping it successfully and oim admin interface is working. I suspect this is permission issue.
If you can help me to resolve this I would appreciate it very much.
Kind regards
MariaIt seems xlclient.cmd got modified. Check if your xlclient.cmd looks like this:
@echo off
setlocal
call classpath
REM SET DEBUG_OPTS=-classic -Xdebug -Xnoagent -Djava.compiler=NONE -Xrunjdwp:transport=dt_socket,server=y,suspend=n,address=5001 -DXL.RedirectSysOutErrToFile=TRUE -DXL.SysOutErrLogFile=.\logs\Client.System.Out.Err.log
REM Make sure to remove java.naming.provider.url and read it from the configuration
REM once the JNDI Profiles are implemented.
REM make sure you are using j2sdk1.4.2_05
"<your java home>" %DEBUG_OPTS% ^
-DXL.ExtendedErrorOptions=TRUE -DXL.HomeDir=C:\Oracle\Middleware\Oracle_IDM1\designconsole ^
-Djava.security.policy=config\xl.policy ^
-Dlog4j.configuration=config\log.properties ^
-Djava.security.manager -Djava.security.auth.login.config=config\authwl.conf ^
com.thortech.xl.client.base.tcAppWindow -server server
endlocal -
Solution manager service desk - configuration -pls help
Hi Forum,
I have completed basic configuration of service desk (solution manager 7.1) and able to realize things like create/process/confirm message and email notification after automatic support team determination (which works well based on component). However facing below issues and have few requirement.
1. Once the support team gets determined automaitcally based on component field 'Support Team' gets filled with a predeifined value which is obvious however furhter to that when i wish to change the 'Support Team' manually its grayed out i.e. i am not able to change it as it goes to non-edit mode. how to solve this issue?
2. In mail notification if message is raised from the satellite system or solution manager itself i am receiving the details of the system e.g. products installed and software components which makes message unneccesarily long. Can i configure system to produce e-mail noification without system info so that a notification can be kept short. (This is required as client needs to use service desk for internal purpose and not happy to see the system information as its increasing the length of the message)
3. While creating organizational structure in /nppoma_crm . i have created organizational unit/Support team/support employees..now in support team determination e-mail notification goes to the determined supoport team (to bp for which e-mail id is entered) however it doesnt goes to the employees mapped under support team as members (pls note bp for each member is maintained along with the e-mail id)
4. I would like to know the method used for automatic sold-to-party determination as like support team determination & is it possible to reset the number range as while test plenty of messages got created e.g. 8000000584/8000000585/8000000586 to be reset to 8000000001 again so client can start from 8000000001.
Please help by sharing your thought on this at earliest.
Regards,
Rupesh
Edited by: rupesh_modi12 on Dec 23, 2011 12:25 PMHi Jitu,
Thank you very much for sharing the links. However sad to say after succesful configuration still the issues mentioned below remains same :
1. Once the support team gets determined automaitcally based on component field 'Support Team' gets filled with a predeifined value which is obvious however furhter to that when i wish to change the 'Support Team' manually its grayed out i.e. i am not able to change it as it goes to non-edit mode. how to solve this issue?
2. In mail notification if message is raised from the satellite system or solution manager itself i am receiving the details of the system e.g. products installed and software components which makes message unneccesarily long. Can i configure system to produce e-mail noification without system info so that a notification can be kept short. (This is required as client needs to use service desk for internal purpose and not happy to see the system information as its increasing the length of the message)
3. While creating organizational structure in /nppoma_crm . i have created organizational unit/Support team/support employees..now in support team determination e-mail notification goes to the determined supoport team (to bp for which e-mail id is entered) however it doesnt goes to the employees mapped under support team as members (pls note bp for each member is maintained along with the e-mail id)
4. I would like to know the method used for automatic sold-to-party determination as like support team determination & is it possible to reset the number range as while test plenty of messages got created e.g. 8000000584/8000000585/8000000586 to be reset to 8000000001 again so client can start from 8000000001.
Regards,
Rupesh -
Problem in ADS configuration .please help me.....
HI experts,
I am new to Interactive forms in WebDynPro for java.
I have installed CE7.1 Dev_studio and J2EEServer.To Develop Adobe Interactive Forms i have installed Adobe Designer7.1.
I am unable to Install a PKCS #12 Credential.
B'coz to paste *.pfx file in my system i don't have folder structure like /global/AdobeDocumentServices/
TrustManagerService/trust/credentials.
i don't have folders from AdobeDocumentServices .
and tried to Configure the credential attributes in Configuration Management ® Infrastructure Management ® Adobe Document Services
There no AdobeDocumentServices.
Can you please help me out from this issues. how to configure ADS in CE7.1.
If i run application i am getting following error.
com.sap.engine.services.webservices.jaxrpc.exceptions.InvalidResponseCodeException: Invalid Response Code: (403) Forbidden. The requested URL was:"http://10.10.20.158:50000/inspection.wsil/, used user to connect: ADSUser"
at com.sap.esi.esp.service.server.query.discovery.WSTransportSettingsResolver.resolveEntity(WSTransportSettingsResolver.java:366)
at com.sap.esi.esp.service.server.query.discovery.WSTransportSettingsResolver.resolveEntity(WSTransportSettingsResolver.java:354)
at com.sap.engine.services.webservices.espbase.query.WSQueryImpl.initialize(WSQueryImpl.java:281)
at com.sap.engine.services.webservices.espbase.query.WSQueryImpl.findWSEndpoints(WSQueryImpl.java:165)
at com.sap.esi.esp.service.server.query.discovery.DestinationsHelperImpl.getEndpointConfigurations(DestinationsHelperImpl.java:924)
... 74 more
Can you please help me out from this issue......
Thanks and Regards,
Shashikiran.BHi,
You can manually create the required folders and deploy the .pfx file. It should then work.
Also, It seems like you have multiple posts on the same issue. Can you please close the rest so that we can resolve this issue on a single thread.
Rao -
ITunes cannot run because of a problem with your audio configuration. HELP
hi guys, i updated to the new version of ituned and hten all of a sudden received this problem. Please help me resolve this situation, as it was working fine 5 minutes before i upgraded to the new version. Is there something i can do? i just bought my shuffle, and am tryign to make it work, but because of this problem, i cant use it. please help
Have you had a chance to look at this troubleshooting page? It may be of some help: iTunes 7 for Windows: iTunes has detected an audio configuration problem
-
Itunes won't run because of some problem with my audio configuration? help!
it specifically says "itunes cannot run because it has detected a problem with your audio configuration". anybody know how to fix that. all i did was when my itunes was werking perfectly fine i was uploading some videos onto it but wen i did it was freezing so i did it again and it froze again so i deleted itunes and installed it again. thats when the problem happened. i tried installing quicktime again. that didn't work then i organized my music and video files but it still wouldn't work. my speakers work good. id on't know what the problem is. CAN ANYBODY HELP????!!!!
Perhaps this Apple KnowledgeBase article will help:
iTunes 7 for Windows: iTunes had detected an audio configuration problem
Good luck.
Forum Tip: Since you're new here, you've probably not discovered the Search feature available on every Discussions page, but next time, it might save you time (and everyone else from having to answer the same question multiple times) if you search a couple of ways for a topic, both in the relevant forums, in the User Tips Library and in the Apple Knowledge Base before you post a question.
Regards. -
Switch configuration urgent help (edge and core)
hi
i have new project in with the bellow product :
20 X WS-C2960-24TC-S
2 X WS-C3750X-48T-S
2 X WS-C2960S-24TS-S
i need to configure this switch in order to work without having vlan, first the 2 core switch for redundancy, then each catalyst switch 2960(edge Switch) connected to the two core with 2 uplink each uplink will be connected to single core switch(i have 2 core switch and i want to configure it in stack mode redundancy)
i need help to configure this switch to work perfectly with each other in best redundancy mode any configuration for this switch will be very helpfull for me
thank youHey,
This is a very open question but i believe the document below is a good point to start:
http://www.cisco.com/c/dam/en/us/td/docs/solutions/Enterprise/Small_Enterprise_Design_Profile/chap2sba.pdf
HTH.
Regards,
RS. -
IMac SPDIF configuration advice - help!
Hi,
I have a mid 2010 iMac and am trying to record into Garageband using the SPDIF input and just cannot figure out which part I havent got right.
I am taking a digital signal from a Fractal Audio Axe FX Ultra on an RCA Coaxial jack, into an optical convertor, the toslink then goes to the mini toslink connector on the input jack of the iMac - all good - the optical cable is lit at the end, so I know it's live.
I can see from the hardware config that the Digital Optical Audio Input and Output are present (and I even plugged the cable into the output to check it would light - it did).
BUT
Where oh where do i make any form of selection for the input to be SPDIF - all the iMac lets me select from System Preference is the Internal Microphone or Line in - no SPDIF. If its not selected or configured here, where is it selected?
Are there settings I need to adjust like the clock rate (I know the Fractal is fixed at 48Khz). If yes, where are they located?
Any help would be much appreciated, it doesnt seem to make sense why it doesnt work, but I know that if the Mac has no option for me to select SPDIF input then its not going to be available in Garageband either...Sorted!
Turned out I had a bad connection at the Coax to SPDIF convertor, clicked the connectors into place and the "Built-In Input" locked onto Digital as the input.
I then had a latency issue with Garage Band, but this disappeared when I changed the sampling rate to 16bit instead of 24. Funnily enough it didnt come back when I switched it back to 24 bit... -
Vonage, dsl and airport configuration need help!
Vonage is not Mac proficient. I cannot get a technician on their end to help me connect the router they sent me to configure it to work with my airport base station and dsl modem. Is there anyone out there who is actually up and running wirelessly via airport extreme base station with a Zyxel P-660R modem from Earthlink DSL with Linksys RT31P2 broadband router from Vonage?
From a quick google, it looks like you should take the ethernet connection from the Zyxel into the RT31P2's "Internet" port. Connect a second ethernet cable between one of the RT31P2's LAN ports and your Airport base station. Set the Airport as a bridge--connect using Ethernet, configure using DHCP, don't distribute IP addresses.
-
FI-CO Configuration "Urgent Help"
Hello SAP Gurus,
Simulate Inventory Mgmt; Entry of Simulation Data
Plant appears as error. Can any of you help in rectifying this . My plant # is not showing in the drop down menu.
If the plant was not created let me know the path and how to rectify this in future.
Thanks !!! [email protected]IMG for SAP Plant Maintain
How to Configure a New Plant in SAP?
Plant 0001 is the SAP default provide for your reference.
OX14 - Define Valuation Area (Tick one only- Once your system go live, no more changes)
Most company take the SAP recommended choice - Value Material Stock at Plant level
Value Material Stock at Plant or Company Level
If you valuate material stocks at plant level, the plant is the valuation area.
If you valuate material stocks at company code level, the company code is the valuation area.
The decision you make applies to the whole client.
OX10 - Create / Change / View Plants
OVXB - Create / Change / View Division
OX18 - Assign Plant to company code
e.g. 0001 - 0001 - All Plants
Px1 - Plant Px1
Px2 - Plant Px2
OX19 - Assignment of company code to the Controlling Area
OB38 - Assign company code to Credit Control Area
OMJ7 - Assign business area to Plant/Valuation area and division
e.g. Plant Px1 - Business Area Bx1
Bx2
Assign Valuation area to the Business Area
.e.g. Valuation area Vx1 - Business Area Bx1
Business Area Bx2
OMS0 - Assign Factory Calendar to the Plant and Business Area
The plant plays an important role in the following areas:
Material Valuation - If the valuation level is the plant, the material stocks are valuated at plant level. Each plant can have its own material prices and account determination.
Inventory Management - The material stocks are managed within a plant.
MRP - Material requirements are planned for each plant. Each plant has its own MRP data. Analyses for materials planning can be made across plants.
Production - Each plant having they own production/planning.
Costing - In costing, valuation prices are defined only within a plant.
Plant Maintenance - If a plant performs plant maintenance planning tasks, it is defined as a maintenance planning plant. A maintenance planning plant can also carry out planning tasks for other plants (maintenance plants).
If you want to use the application PP (production planning) or product costing and job-order costing, you must set valuation at plant level.
The valuation level that you choose affects
the maintenance of material master records
the G/L accounts in which material stocks are managed
the G/L accounts to which transactions are posted in Materials Management
Effect on the maintenance of material master records:
Depending on the valuation level chosen,
you maintain accounting data in the material master record for each plant or for each company code
you define a valuation price for the material in each plant or in each company code
Effect on G/L accounts:
If material stocks are valuated at company code level, all plant stocks of a material are managed in a joint stock account for each company code.
If material stocks are valuated at plant level, you can manage the material stocks for each plant in different accounts. For each plant, you can define a separate determination.
If several plants are to use account determination, you can group these plants in "Valuation and Account Assignment" Customizing.
Maybe you are looking for
-
i am trying to reinstall itunes 10.5 and am getting the following error message. An error occurred during the installation of assembly "Microsoft.VC80.CRT.type="win32".version="8.0.50727.6195".publicKeyToken="1fc8b 3b9a1e18e3b".processorArchitecture=
-
I moved my itunes library to external drive and now itunes wont work.
I moved my itunes library to an external drive and now itunes cannot find the library. I followed a youtube video and all seemed to work fine until i deleted the old library and emptied the trash. Prior to deleting and emptying the trash I checked pr
-
Episode 1: Weblog: Logistic Cockpit Delta Mechanism
Hi, I just completed reading this document (Logistic Cockpit Delta Mechanism Episode 1) by Roberto and I will appreciate if you can clarify these for me: 1. The entire document(Episode 1) is about V3 Update, the Serializer but if the superior Updat
-
Error after XDK 9.2.0.4.0 upgrade
After upgrading from XDK 9.2.0.1.0 to XDK 9.2.0.4.0 I started logging the following error during an XML document post (which has never occurred in previous XDK versions): java.lang.NoClassDefFoundError: oracle/sql/OPAQUE at java.lang.Throwable.fillIn
-
I Can't Open Any of my Pages 08 Documents
I never upgraded to Pages 09 because by the time I was ready to purchase it, I figured a new one was just around the corner. (Clearly this was a bad decision as I was kept waiting for 4 years, and then even then the upgrade is being offered for free