Yet again help re speed problem
First todays stats
ADSL line status at 1359 on 01/04/11
Connection Information
Line state Connected
Connection time 0 days, 00:00:19
Downstream 1,151 Kbps
Upstream 888 Kbps
ADSL Settings
VPI/VCI 0/38
Type PPPoA
Modulation G.992.5 Annex A
Latency type Interleaved
Noise margin (Down/Up) 23.1 dB / 14.4 dB
Line attenuation (Down/Up) 21.6 dB / 4.6 dB
Output power (Down/Up) 20.2 dBm / 1.3 dBm
Loss of Framing (Local/Remote) 0 / 0
Loss of Signal (Local/Remote) 0 / 0
Loss of Power (Local/Remote) 0 / 0
FEC Errors (Down/Up) 0 / 0
CRC Errors (Down/Up) 0 / 64
HEC Errors (Down/Up) 7 / 0
Error Seconds (Local/Remote) 0 / 0
Hub v2 is connected to filtered master socket. SN and attenuation figures look good to me but download speed is 597 Kbps.
Speedtester shows dsl set at 1151 and ip profile at 750. Is this the cause of disconnections?
Have had BT Engineer visits but no improvement
Anyone any idears please
Keith
Solved!
Go to Solution.
Imjolly
Thanks for the reply - nice to hear/speak again
Yes hub has to be reset 2/3 times per day. so far today at 1030 / 1400 and 1730. The info I was working from off another site is
Noise ratio. The higher the number the better for this measurement. In some instances interleaving can help raise the noise margin to an acceptable level.
6dB or below is bad and will experience no synch or intermittent synch problems
7dB-10dB is fair but does not leave much room for variances in conditions
11dB-20dB is good with little or no synch problems* (but see note below)
20dB-28dB is excellent Mine whis is why I said good
29dB or above is outstanding
Line Attenuation
Measure of how much the signal has degraded between the DSLAM and the modem. This is largely a function of the distance from the exchange. The lower the dB the better for this measurement.
20dB and below is outstanding
20dB-30dB is excellent Mine which is why I said good
30dB-40dB is very good
40dB-50dB is good
50dB-60dB is poor and may experience connectivity issues
60dB or above is bad and will experience connectivity issues "
Do you have other figures?
Similar Messages
-
Another problem... yet again HELP!
I am having yet another issue with my blackberry curve 8530. I already am aware the battery (CS-2) needs to be replaced due to the fact that I need to charge it 3 times a day. Additionally however, it reboots itself 2 times a day also.. Requiring me to charge it 5 times a day now. Once it reboots the battery becomes completely drained of course. Is there any specific cause to the phone rebooting? Or is it possibly linked to my battery needing to be replaced? I just don't want to spend $50 on a new battery if my phone reboot issue is unfixable.
PLEASE HELP!Hi britters,
Sorry to hear you're having issues with rebooting and battery life on your BlackBerry® Curve™ 8530 smartphone.
You can rule out any possible software issue that may be causing this by backing up your data using the BlackBerry® Desktop Software and performing a clean reload of your BlackBerry® Device Software. For further instructions, please see the following KB articles.
For Windows®: "How to perform a clean reload of the BlackBerry Device Software for Windows" http://bbry.lv/GI9beY
For Mac: "Perform a clean reload of BlackBerry smartphone application software using BlackBerry Desktop Software on a Mac computer" http://bbry.lv/J0UN1U
Please test to make sure both issues have been resolved before restoring any data from your backup file. If the software reload does not resolve the issues, I would suggest testing with another battery if possible.
Hope this helps.
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)! -
Help with speed problem please.
Hello, I need some help please with my BT broadband. My speed has dropped and now is very slow its always been up and down, at its best it's been 4mbps and has never dropped below 1mbps untill now. I have tried to provide what I think you may need, had internet with bt for a year and this is the first time I have had a problem since having broadband. I want to find out if I can why my speed has dropped.
Your connection reset tonight was that router droping connection or manual reset?
your noise margin is at 19.3db which is very high as normal is 6db. Has your connection been dropping often?
are you connected to the test socket? If not can you connect to test socket
try quiet line test. Dial 17070 option 2. Should be quiet and best with corded phone. If cordless then dull hum normal
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’. -
Fan speed problem Power Mac G5 Dual 1.8 GHz PowerPC - please help
Please HELP, I have a fan speed problem with my Power Mac G5 Dual 1.8 GHz PowerPC
This is a NOT an Intel machine. I am running Mac OS X v10.5.8
Power Mac G5 - PowerMac 7,2 - Power PC 970 (2.2) - 1.8 GHz with 2 CPUs - L2 Cache (per CPU) 512 KB - Memory 8 GB - Bus Speed 900 MHz - Boot ROM version 5.1.5b1
I have included below Links to download a sound file (.m4a) that I recorded of the fan speed problem and both a .pdf and .spx files of my system profile.
download sound file
http://homepage.mac.com/rep3/filechute/myG5dualsFans.m4a
down load .spx file of my system preferences
http://homepage.mac.com/rep3/filechute/systemProfileREP3-G5dual.spx
down load .pdf file of my system preferences
http://homepage.mac.com/rep3/filechute/systemProfileREP3-G5dual.pdf
When did the fan problem start?
After I replaced the mother board on the computer.
Why did I replace the mother board?
Because the experts at apple agreed with my diagnosis that the major crash problems & kernel panics must have some thing to do with a logic board gone bad. They would not work on it, because this Power Mac G5 dual 1.8 GHz machine is now a legacy model.
What I have done to attempt to fix my fan speed problem? yes I checked the obvious things, here is a list:
1) yes I checked to be sure that the new mother board was the same part number as the original one, and that all things that were unplugged from the old mother board - were actually plugged into the new mother board.
2) all the fans work, I can see them spinning if I use a flashlight and look at them (cover on and off to get at some of them)
3) check all RAM to make sure: a) it was installed properly b) that the RAM worked using TechTool Pro c) even started the machine with only the original RAM that came with it.
4) I installed a Temperature monitor - to see if there was something reading as very hot inside that was causing the machine to continually run the fans at a high speed. No, no heat issues that I can see. Here are the reading from the sensors in degrees fahrenheit, 2009-10-11 16:11:01 -0500
CPU A Die Temperature: 75.7℉
CPU B Die Temperature: 81.5℉
Drive Bay: 68.9℉
Main Logic Board Air Inlet: 64.8℉
Main Logic Board Ambient: 73.6℉
Main Logic Board Backside: 76.3℉
Memory Controller Heatsink: 93.2℉
Processor Card A Ambient: 77.5℉
Processor Card B Ambient: 77.0℉
5) zapped the PRAM
6) followed the SMU reset instructions for
Power Mac G5 (Late 2004)
To reset the SMU on a Power Mac G5 (Late 2004) computer, simply do the following:
• Turn off the computer by selecting Shut Down from the Apple menu or by holding the power button until the computer turns off.
• Remove the power cord from the computer.
• Wait two minutes.
• Plug in the power cord.
• Turn on the computer.
7) followed the SMU reset instructions:
Resetting the Cuda/PMU
How to reset the PMU:
• If the computer is on, turn it off.
• Disconnect ALL cables from the computer, including peripherals and power.
• If possible, move the computer to a place where you are not standing on carpet.
• Open the case and ground yourself by touching part of the metal frame inside the computer.
• Find the Cuda or PMU button
• Press the Cuda or PMU button ONCE. Do not press the button more than once before starting the computer up again.
• Wait 10 seconds, then reconnect the cables you removed in step 2 and turn the computer on.
• If the computer still does not respond after resetting the PMU, the computer may require service from an Apple Authorized Service Provider.
8) ran disk utilities, repaired permissions
9) found a setting in the system preferences that a chat room person suggested had something to do with fan speed. In Energy Saver, under options, processor performance was set to highest, I set it to automatic - this did not change anything that I could tell - BTW I checked my other G5 (a single processor that works fine) that is the setting that that it is set to, and it is nice and quiet.
10) restarted the machine, ..
11) found a Fan Control System Update - but it did not install when I tryed to install it -
12) booted from OSX install disk and ran that disk utility
13) used OnyX to fix disk permissions, clear caches and temp items
Nope - still have the same high speed fan problem. ... PLEASE HELP!!
I have been reading in the MacInTouch reader reports - found this: some one said to use this - thermal re-calibration using the Apple Authorized Service Providers' disk - but that's not available, at least I can not find it - anyone? have an answer to finding this - or can do it for me? I am in Chicago.The Genius at the downtown apple store said that because it's a "legacy machine" they would not work on it, .. so should I push them?
Well, I personally think that's ridiculous, I'd Push them, I'd call AppleCare & talk up the chain if need be... there the ones that have or should have that Disc... man o man... Personally I'll never visit an Apple Store again in my lifetime, maybe try an independent AASP if none of that helps!..
http://tinyurl.com/ykomqkn
Man-o-man, pop my cork before I explode on that one, if I had anything to do with it I'd close that store. -
I believe I have a problem when opening up my documents in finder. where upon I can view all my folders but with yet another Documents folder within this group, if I then click on this second Documents folder yet again a repeat of the do'cs folder appears. I have tried to merge the Documents folders into one but after a morning and a few hours later having completed the merge when I reopened the folders the problem was still there. Help.
SandraReset the PRAM
Reinstall the operating system from the dvd (you will not loose your data) -
Garbage broadband speeds in Shetland yet again!
Yet again I find myself on here complaining about the garbage level of broadband speeds up here in Shetland. Its been on a go-slow all day and BT once again deny any problem exists.
Results of the latest speed test:
Ping: 1018ms
Down: 0.23Mbps
Up: 0.10Mbps
Absolute tripe. Get it sorted BTHeres the result from the bt speedtester
FAQ
This Test comprises of Best Effort Test: -provides background information.
Download Speed
274 Kbps
0 Kbps
2000 Kbps
Max Achievable Speed
Download speedachieved during the test was - 274 Kbps
For your connection, the acceptable range of speeds is 400-2000 Kbps.
Additional Information:
Your DSL Connection Rate :1568 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 1250 Kbps -
Hi,
When i open my Password Reset portal then provide Username credentials in text box and click on next then asked the Securites Question Answers to me,i provide the correct Answers to the securites Question after this password reset portal asked
me New Password and Confirm Password then click on next for resetting the password then gives below Error only for 2 Users. and all other users are working fine.
An error has occurred. Please try again, and if the problem persists, contact your help desk or system administrator. (Error 3000:)
Regards
Anil KumarAnything in the event log?
-
After installed mavericks i cannot sign in to my facetime and i messages. i tried it 100 times, but it is showing couldn't sign in check your network and try again. there is no problem with my network. if anyone knows the solution please help me .
Hi,
What version of the OS did you upgrade from ?
Anything before OS X 10.8.2 may have an issue if the Logic/Mother board has been replaced and the Serial Number not "flashed" back to it.
In the Apple Icon menu use the About this Mac item.
In the new panel click twice on the line that tells you the current OS level
It will change to the Build number (and alternative count to the OS versions) and then the Serial Number.
If it is missing you need to get it replaced.
(It is supposed to be done on Repair or Refurbishment).
An Apple Store or Apple Authorised Service Provider as the best choices.
There are apps you can download (They are Mac Model specific) but needs careful typing as it is a once only trip.
8:56 pm Sunday; November 24, 2013
iMac 2.5Ghz 5i 2011 (Mavericks 10.9)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
Couple of iPhones and an iPad
Message was edited by: Ralph Johns (UK) -
My itunes radio rebuffers every 8 seconds - is there any fix or help for this problem. I am running the latest itunes on a new Mac with 4MB download speed.
You need to update your Mac OS to at least 10.5.8.
Itunes 10+ requires Mac OS 10.5.8+ -
Unable to install the GEAR driver set at this time.The GEARAspiWDM service used bz the GEAR driver set is scheduled to be deleted during the next system reboot.Please reboot the system and run iTunes again.help me..I understand this problem..thanks
Hi there, i had the exact same problem and posted a thread a few above yours, and these forums wasnt much help nobody replied, so i did a bit of research and followed all the intructions on this site: http://www.gearsoftware.com/cfknowledgebase/articledisplay.cfm?articleid=296
If you follow the steps very carefully and do as each says, this will solve your problem.. Now i am very happy i can actually install iTunes and use it for my iPod.
Remember to be carefully with the steps as the things you will be deleting are very important to your comp.
Hope this helps.
Windows XP -
My iPhone 5 frequently crackles and pops loudly during calls (while using speaker phone, as well as not using speaker phone.) After being inspected by techs at the Genius Bar, my phone has been replaced twice; thus, I am currently on my third iPhone 5. Incredibly, I am, yet again, experiencing the exact same issue. Short of getting my fourth iPhone, is anyone aware of a solution?
if it's the exact same issue, either it's a problem with your service or with your software if you're restoring from a backup each time. it's pretty darn near impossible for 3 phones to have the same exact hardware issue, so that's unlikely. is this an at&t iphone? if so, are you continuing to use the same sim card? if so, get a new one and try that out. if that's not the issue, restore the phone as new and make a few phone calls. if the issue's gone away, there's something wrong with your backup
-
My Ipad reboots over and over again could someone help with my problem?
My Ipad reboots over and over again, could someone help with my problem?
Try a reset. Hold the Sleep and Home button down for about 10 seconds until you see the Apple logo.
-
I.P Profile stuck yet again at 2Mbps
Hi,
I have had this problem 3 times in the past 6 months and its getting pretty tiresome.
My I.P profile is stuck YET AGAIN at 2Mbps. Please can:
1. Reset it back to my normal speed.
2. Give me any advice as to why it keeps happening.
I have heard that it could be down to having to restart the homebut, but I only do this maybe once every 2-3 weeks when the wifi decides that nobody should get an I.P address...
Here attached is the Wholesale test and my HomeHub 2.0 uptime.
Kind regards,
Alexthis is normally caused by your line dropping connection or manually resetting a few times in a very short period and on one of the resets the connection speed drops low that correct profile is 2mb then you reconnect again and get your normal 8128 connection and your profile should correct itself automatically in your case it gets stuck
mods will post the contact us link again
After completing the email NOT PM then you join a queue of other customers waiting for mod help. The mods will get back to you in 3/5 working days either by phone or email
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’. -
When I publish my site on one specific page where I've added {tag_pagecontent} I get the error:
'Some files on the server may be missing or incorrect. Clear browser cache and try again. If the problem persists please contact website author.'
I'm trying to get a blog module going, I've even deleted the html insert bog with the tag in and re-published which then I don't get the error but as a result no blog either. But then I add the tag in again and publish the error comes back. I've used the dev console and it says that my musicians sample.css is out of date but why is it only out of date when I add in html to my muse site?
HELP!!!! I've searched other threads and to no avail I'm publishing so no direct ftp going on. the only thing I changed in business catalyst was the module stylesheet in order to style the blog. I've tried uploading and replacing all files nothing seems to work. the site is here:
http://www.musicstudentsforhire.co.uk/musicians-samples.html
It's only this page as it has the blog on. Also I've noticed when I've re-published occasionally it will show the mobile version on my desktop and not the desktop version??? no idea why that's happening so I've had to turn that off. any explanation on why that is happening would also be much appreciated.I haven't received an answer as of yet, I'll post t on here when I do. I de-activated the mobile site because it's my clients site so he needs it to be operational during the day. I hope someone gives me an answer soon.
-
How can I stop music and movies from being automatically deleted from my phone and saved on the cloud? I've just tried to watch a movie on my 2 hour commute, but yet AGAIN it has been removed. I do NOT want to spank all of my data allowance downloading it again, especially because (believe it or not) I added it to my phone because that's precisely where I wanted it!! Any help much appreciated
FYI I had to put this link into firefox to reply - because **** back safari just wouldn't register my clicks to any of the links on the post... Despite reloadeing and even restarting my computer. Totally annoying and a massive pain in the ***.
But in terms of my initial query; thanks for responding. But no, this is NOT the cause of the problem. I have auto sync and sync over wifi activated, but have also selected manually manage music and videos. Plus, all of my music and videos are on my macbook, absolutely all of it, so if it my phone was syncing with my macbook everything would still be on the phone. Life would be peachy if my phone jsut copied everything that was on my macbook, but unfortuantely it keeps deleting tracks for no apparent reason.
Any thoughts greatly welcomed, because at the moment i can only conclude that my iphone is crap.
Maybe you are looking for
-
Hi, Is it possible to create a Report Script that would export Period data (jan, feb, ... dec) condition being that the start period is a subvar. Eg. from &FcstMonth to Dec, where &FcstMonth is Aug. Regards Leo
-
Enterprise manager Grid Control for Windows 64 bit
Hi, I am looking for Enterprise Manager Grid Control 10.2.0.3 for Microsoft Windows Server 2003 R2 64 bit. On OTN and metalink I can only find for 32 bit. Can anyone suggest where I can find the same. Thanks in Advance. SK.
-
ejb-local-ref where to put this tag in ejb-jar.xml ??
I have an ejb-jar.xml that looks like this. I have had no problem with remote interfaces. Now I want the bean to have a local interface too. Just let me know where the tag I have mentioned for the <ejb-local-ref> has to be put into. When I compile th
-
I purchased my Iphone 5 on the day of release, since then I have had a 2 day battery life on average, since upgrading to IOS 6.0.2, the battery struggles to last for 4 hours, is there any solution or fix?? If not any idea when this will be fixed??
-
Looking for advice: Purchasing a MacBook Pro
Hi everybody, I am a graduate student, and I do computational chemistry. The software we use in our lab is Windows-based, and the simulations we run require a lot of processor power. I am thinking about buying a MacBook Pro, on which I can run Window