Zc706-Read data from DDR, send to FMC card pins

Question

Hi,
There will no direct FMC IP available but you have to make your peripheral(s) in desing to drive the FMC card I/O interfaces.
The ZC706 evaluation board supports the FMC of the high pin count (HPC) connector at J37 and low pin count (LPC) version at J5.  FMC card interface pin details are given in page 65 of  http://www.xilinx.com/support/documentation/boards_and_kits/zc706/ug954-zc706-eval-board-xc7z045-ap-soc.pdf. This should go in to the xdc file.
Refer to the an example tutorial http://community.em.avnet.com/avnet/attachments/avnet/FMCHDMIIOVITAImageSensor/420/1/FMC_IMAGEON_GettingStarted_2014_4-Tutorial.pdf.
Regards
Praveen
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.
Give Kudos to a post which you think is helpful and reply oriented.
 

Answer 1

Dear
I made our peripheral(s) FMC card I/O interfaces and in the constraint file, to assign the output to go to fmc pins, i set like this:
set_property PACKAGE_PIN AB4 [get_ports {o_cam_d[1]}]
set_property PACKAGE_PIN AB5 [get_ports {o_cam_d[2]}]
set_property PACKAGE_PIN AB11 [get_ports {o_cam_d[3]}]
set_property PACKAGE_PIN AB1 [get_ports {o_cam_d[4]}]
set_property PACKAGE_PIN U11 [get_ports {o_cam_d[5]}]
set_property PACKAGE_PIN AA11 [get_ports {o_cam_d[6]}]
set_property PACKAGE_PIN AB2 [get_ports {o_cam_d[7]}]
set_property PACKAGE_PIN U12 [get_ports {o_cam_d[8]}]
set_property PACKAGE_PIN AA4 [get_ports {o_cam_d[9]}]
set_property PACKAGE_PIN Y4 [get_ports {o_cam_d[10]}]
set_property PACKAGE_PIN Y10 [get_ports {o_cam_d[11]}]
set_property PACKAGE_PIN Y11 [get_ports {o_cam_d[12]}]
set_property PACKAGE_PIN AB6 [get_ports {o_cam_d[13]}]
set_property PACKAGE_PIN AB7 [get_ports {o_cam_d[14]}]
set_property PACKAGE_PIN AB9 [get_ports {o_cam_d[15]}]
set_property PACKAGE_PIN AB10 [get_ports {o_cam_d[16]}]
set_property PACKAGE_PIN AB12 [get_ports {o_cam_d[17]}]
set_property PACKAGE_PIN AA12 [get_ports {o_cam_d[18]}]
set_property PACKAGE_PIN V4 [get_ports {o_cam_d[19]}]
set_property PACKAGE_PIN W12 [get_ports {o_cam_d[20]}]
set_property PACKAGE_PIN V5 [get_ports {o_cam_d[21]}]
set_property PACKAGE_PIN U9 [get_ports {o_cam_d[22]}]
set_property PACKAGE_PIN AA8 [get_ports {o_cam_d[23]}]
set_property PACKAGE_PIN V12 [get_ports {o_cam_d[24]}]
set_property PACKAGE_PIN U10 [get_ports {o_cam_d[25]}]
set_property PACKAGE_PIN T6 [get_ports {o_cam_d[26]]}]
set_property PACKAGE_PIN AA9 [get_ports {o_cam_d[27]}]
set_property PACKAGE_PIN AA6 [get_ports {o_cam_d[28]}]
set_property PACKAGE_PIN R6 [get_ports {o_cam_d[29]}]
set_property PACKAGE_PIN U4 [get_ports {o_cam_d[30]}]
set_property PACKAGE_PIN AA7 [get_ports {o_cam_d[31]}]
set_property PACKAGE_PIN T4 [get_ports {o_cam_d[0]}]
set_property PACKAGE_PIN U6 [get_ports {o_href}]
set_property PACKAGE_PIN U5 [get_ports {o_vsync}]
set_property PACKAGE_PIN Y6 [get_ports {o_px_valid}]
#set_property PACKAGE_PIN Y5 [get_ports {i_px_ready}]
set_property IOSTANDARD LVCMOS25 [get_ports o_href]
set_property IOSTANDARD LVCMOS25 [get_ports {o_cam_d*}]
set_property IOSTANDARD LVCMOS25 [get_ports {o_vsync}]
set_property IOSTANDARD LVCMOS25 [get_ports o_px_valid] 
But when I run synthesis, there are critical warnings like this:
[Common 17-69] Command failed: 'AB4' is not a valid site or package pin name. ["D:/Research/lisa/fmcprojects/fmcinterface/fmcinterface.srcs/constrs_1/new/fmcpins.xdc":2]
[Common 17-55] 'set_property' expects at least one object. ["D:/Research/lisa/fmcprojects/fmcinterface/fmcinterface.srcs/constrs_1/new/fmcpins.xdc":27]
[Vivado 12-1815] Setting property 'IOSTANDARD' is not allowed for GT terminals. ["D:/Research/lisa/fmcprojects/fmcinterface/fmcinterface.srcs/constrs_1/new/fmcpins.xdc":42]
So I couldn't do implementation. Can you give me some ideas about this problem ?