After installing an application that was created using the Application Builder

After installing an application that I created using the Application Builder I get this error if I try to run " ANY " LabVIEW App's that I have built. "Executable Version 7.1.1 doesn't match Resource File 7.1. Check your configuration."
The way that I tried to fix this is to reload LabVIEW 7.1 and DAQmx 8.0. I am using two NI-6528 switch cards.
After I reload LabVIEW and DAQmx I can run my applications but as soon as I install one on this development machine the error begins again.
The executable that I built works fine on the development machine and any other machine that I try it on but it appears that the Run-Time engine 7.1 becomes corrupt after I run setup.exe for the newly created application.
I have built numerous Installers, setup.exe's in the past without this error. Just this latest one caused this problem to start.
I can NOT upgrade to 7.1.1. I am doing work for many different sections of this factory and I can not force them to upgrade. I've asked. Others supply code for the same machines using LabVIEW 7.1.
I am stuck creating executables and manualing moving the correct files to the target machines.
What can be done?

No. The KB article was talking about a machine with 7.1.1 installed. I have LabVIEW 7.1 installed.
The machine that I am having trouble with is my development machine. LabVIEW 7.1, DAQmx 8.0.
If I build the executable all is fine. I can still run old executables including the one I just built.
If I create the installer all is fine. I can still run old executables including the one I just built.
When I install the app on my development machine the corruption occurs. I can " NOT " run old executables including the one I just built. The subject error pops up.
I have not moved any executables to the other machines yet. I don't want to corrupt others.

Similar Messages

Is it possible to change the first page of a web application that was built using the UI?

Hello Community
    Using Sharepoint 2010 Server and the UI I built and application and would like
to continue building the web application using the UI.
    The application's first page was built using a Blank Site template and
the subsequent subsites were built using the Team Site template.
    In retrospect the first page should also have been built using a Team Site template.
    It may be unnecessary to make to delete the application
and create the first page as a Team Site and then have to create all of the
subsites (Team Sites) all over again.
    As a solution to prevent deleting the whole application and creating application
with all of the subsites all over again whether it is possible to do any of the
following:
    - Convert the Blank Site page into a Team Site page which would allow
me to leave all of the subsites as is.
    - rename the Blank site page which would in effect would be renaming the application
then create a new Team Site page which would be essentially creating a new application and
then adding all of the subsites contained in the renamed application that has the first page
as a Blank page.
    And if is possible to add, copy or move the subsites from existing sites to a new Team Site
page, how do you add, copy or move the subsites from one application to a diffent application?
    Thank you
    Shabeaut

Hi Shabeaut,
According to your description, my understanding is that you want to change the template of the root site without creating the susites in another web application.
I recommend to export all the existing subsites and import them to new web application.
More references:
http://social.technet.microsoft.com/Forums/sharepoint/en-US/cc7c11ec-e4da-4ddb-babd-db76ccb35664/move-subsite-to-new-site-collection?forum=sharepointadminprevious
http://social.technet.microsoft.com/Forums/sharepoint/en-US/fd321bac-16a7-47e4-842e-00b7ca0f7f05/move-subsite-to-other-site-collection-as-subsite?forum=sharepointadminprevious
Best regards.
Thanks
Victoria Xia
TechNet Community Support

I can not open ff4(after installed) with a note you cannot use the application "firefox. app" with this version of Mac OS X.

I had ff3, but I upgraded to ff4. But in process of upgrading to ff4 I almost 70 times of dragging from ff simbol to applications, I am so tired of repeating it, So I stopped. and as last step I dragged ff simbol from appplication to side ff simbol. Next day I tried re-download over it, But it happen same thing, it says "you cannot use application"firefox. app" with this version of Mac OS X."

Firefox 4 requires at least OS X 10.5 and an Intel Mac.
* http://www.mozilla.com/firefox/4.0/system-requirements/
For Mac OS X 10.4.11 or Mac OS X 10.5.8 you can look at:
* http://www.floodgap.com/software/tenfourfox/
Firefox 3.6.x can be found here:
* http://www.mozilla.com/en-US/firefox/all-older.html

How to include a .lvlib in a build that was created using a custom .dll

I am trying to build an executable in LV2010 that uses a .lvlib that was created using a .dll from Keyence. I have added the .lvlib to the source files as "Always Included" and I have also added all of the .vi files of the library to "Always Included." I still get the error saying "Missing External Function" when running the program. The executable seems to open fine on the development computer but not on a secondary computer. Any ideas?
Solved!
Go to Solution.

...I assumed too quickly that the problem was resolved. By specifying the path I was actually able to open the executable after installing but none of the .dll functions worked. I noticed that when I specified a path on the diagram, the .dll was no longer included in the dependencies and was no longer included in the build. I guess this would explain why none of the functions were working. I copied the .dll over to the path specified on the diagram and it still did not function.
This brings me back to the original problem I was facing. I actually removed the .lvlib. I replaced all of the library vi references with the Call Library Function and deselected the "Specify path on diagram" Boolean. When I do this, the build includes the .dll in the dependencies list and it includes the .dll file in the destination folder of the install. However, when running the executable I get a list of errors that read, "Missing external function …” I have attached an image of this error. This is the same error that occurred when I was using the library, but I thought maybe the library was the cause of the problem, which is why I used the Call Library Function instead.
*I have tried adding the .dll to the support files and I receive the same error when trying to run the executable.
*I have tried adding the .dll to the support files and making it an “always include” in the installer properties under source files. This returns the same error.
I’m really not sure where to go from here. Any help is greatly appreciated!
Attachments:
Call Library Function.jpg ‏56 KB
Error.JPG ‏23 KB

Why do vector lines appear different in my Photoshop document compared to the PDF that was created using "Scripts Layer Comps to PDF"? And how do I get them to look the same?

Why do vector lines appear different in my Photoshop document compared to the PDF that was created using "Scripts > Layer Comps to PDF"? And how do I get them to look the same?

BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

Convert an integer value that was created with the Excel DATEVALUE formula to a valid date?

Hello everyone,
How can I convert an integer value that was created with the Excel DATEVALUE formula to a valid date in SSIS?
Is this even possible?
For example:
=DATEVALUE("8/22/2008") will format the cell to display 39682.
Reading the column as a string to get the int value (39682) - how can I turn this into a valid date using SSIS and then importing the real date to sql server?
Thank you!

You can use Script component for this and convert your integer values to Date. An example here is following:
CultureInfo provider = CultureInfo.InvariantCulture;
string dateString = "08082010";
string format = "MMddyyyy";
DateTime result = DateTime.ParseExact(dateString, format, provider);
Source: http://stackoverflow.com/questions/2441405/converting-8-digit-number-to-datetime-type
Vikash Kumar Singh || www.singhvikash.in

How to get the vendor number that was created using xk01..?

Suppose i am creating a vendor with all the information by using a bdc program.
In the same program if i want to go to the XK02 of that particular vendor that was created recently....how it possible..?
Means how to get that particular vendor number that was created recently...?

Hi...
You Can Get the Vendor number after Calling the Transaction 'XK01' as below.
Declare a table for Collecting messages :
DATA: T_MSG TYPE TABLE OF BDCMSGCOLL,
 WA_MSG TYPE BDCMSGCOLL.
Then Call Transaction Statment:
CALL TRANSACTION 'XK01'
 USING T_BDCDATA
 MODE 'N'
 MESSAGES INTO t_msg.
if sy-subrc = 0.
READ TABLE T_MSG INTO WA_MSG WITH MSGTYP = 'S'.
 MSGID = 'F2'
 MSGNR = '175'.
Note: Bcoz the XK01 will issue this message
if sy-subrc = 0.
write: / WA_MSG-MSGV1. "This will contrain Vendor Number
endif.
endif.
And you can also Try the Other method i.e. after the Call transaction statement
 GET PARAMETER ID 'LIF' field V_LIFNR.
WRITE:/ V_LIFNR.
Reward if Helpful.

Using a environment variable that was created during the Task Sequence process - SCCM 2012 R2

Hi,
I'm triyng to use a environment variable that is create in the beginning of the Task Sequence.
1. I'm using a VBScript that get the Exit Code of an application, and create the environment variable "iReturn" with the value of the exit code. (This is working)
2. I add this variable in the CustomSettings.ini, like this "iReturn=%iReturn%
3. After the step that I run the VBScript I put the "Gather" step to get the variables, but looking in the BDD.log the iReturn variable appears the same as the CustomSettings.ini configuration "iReturn=%iReturn%". (But, if I put a "Restart
Computer" step after the VBScript, the BDD.log shows the iReturn variable with the right code.)
Question: How can I update the environment variable of Windonws XP to use in the Task Sequence without restart.
OR
How can I configure autologon in SCCM 2012 (if have no way to update withou restart computer).
I already tried the autologon with registry settings and a specific user, If I starts the process with this user works, but If I starts the process with other user, after the autologon the process doesnt continue, I have to do logoff and login with the user
that I started the process.
PS: All this steps have to be executed before the WinPE phase.

Environment variables must be explicitly set every time a system boots so unless you have a process to repopulate it after the reboot, it won't persist automatically.
Why not store the value in a task sequence variable so that it persists after a reboot?
Jason | http://blog.configmgrftw.com | @jasonsandys

Safari is the only application that can successfully use the internet.

Dear all,
I have been having internet problems for the past couple of weeks, that started fairly suddenly. The problem is that any of my internet-using applications cannot use the internet, apart from Safari. Browsing and downloading through Safari work seamlessly, but all other uses of the internet fail.
For example, Messenger for Mac gives me a message indicating that I am not connected to the internet. Skype also does this, and the iTunes Store tells me that the host is down, and that I should check my internet connection and try again. Software Update is another application that cannot function as a result of this problem.
I am living in student halls at university, so my internet connection is an ethernet cable plugged into the wall, and therefore I have no access to the behind-the-scenes things. I have contacted my internet provider (Ask4), to ask if they'd changed anything, but they said not, but are very willing to do anything they can to help me.
It has been suggested to me that I simply create a new location in network settings, and that this would remedy the problem, but it didn't work.
Another suggestion was to temporarily disable the firewall, but this also didn't help.
Does anyone have any suggestions as to what I could try next, because I'm all out of ideas, and I can't find anyone with the same problem.
Any help would be well-appreciated.
Thanks
Tom

i figured it out. reboot the phone. its an ios4 bug that once you turn the orientation lock on once and back off, the photos wont rotate and you have to reboot. hopefully a fix comes soon

How do I disable the feature that asks, "...is an application that was downloaded from the Internet. Are you sure you want to open it?" I get this message every time I double-click to unpack a zip file.

I am using Firefox 6.0 (I know it's an older version, but I am a doctoral student at a university that is whose system is, at this time, only compatible with this version) on an Intel Mac.

If using a mouse, you can right click on the application installer this will give you an "Open with" popup and you can chooes to open the application installer using the standard installer.
Another method to do the same exact thing is to hold the Control key while left clicking on the Application installer will give you the exact same popup menu.

Is there anything that you can do to fix a pdf that was created with the wrong orientation?

Someone sent me 40-page pdf created from a document with landscape orientation that was output with portrait orientation. The pages are clipped off on the right and left. There is no way that I can see that you can change the orientation in Acrobat Pro and if it is converted into a Word document you can see most of the text, but there is still some missing, especially where there are tables. I don't have access to the original document. I was just curious if there was a way around this?

Thanks, that is what I figured. Just thought I would ask. Some of the text that was clipped off did appear when the pdf was converted into a word file, but not all of it.
Mary Jane

Cannot fill a form in Reader 9.x that was created using Professional 8.1.3

I created a form using Acrobat Professional 8.1.3 that our students must fill out using Acrobat Reader 9.x
My computer and the Reader 9.x computers have Windows XP installed.
The form opens in Reader 9, but none of the fields show. There are no drop down boxes or areas to type the info showing and the save option does not show. The form opens fine in Reader 8. Reader 9.x is the only version installed on the problem computers.

Susan,
I'd be interested in looking at the file if you are free to email it to me.
George

How can I cancel an order, that was created using Guest Checkout? Or how can I associate in with my account?

Wanted to buy ipod nano, but got a problems with payment information. And now can't cancel an order.

Where did you try and order it? From Apple's website? Perhaps this page can help.
Viewing & Changing Orders
B-rock

Deleting applications that are not in the application folder

I recently downloaded an app called Liteswitch. I didn't want it so I ctrl clicked on its icon in the System Preferences and removed the Liteswitch prefpane. But the app is still installed and working - how do I get rid of it?
Thanks

It's not only the Liteswitch app. It's more in general. I can't figure out if the apps are deleted when you ctrl click on their icon in the system prefs and remove it. The app still works after you have done this so it seems that it doesn't delete it. However after logging out the app doesn't work after logging back in, so maybe OSX waits to delete the app till you log out?

Issue with using a form saved in ES3 that was created in ES2

I have a base doc form that was created using ES2 designer. This file is stitched together with several other documents to create a application pdf. The file contains javascript, etc. Everything works correctly when I run the process that stitches the documents together. When I open the file in ES3 and save it and check it in, the process no longer works. I get a unable to stich document error. Any ideas?

not really, someone else mentioned that it could be done and they said they saw it before. I've been beating myself up for a while trying to figure out how to get it to happen. Is there an easy way to get the content of the pdf form into an email body with plain text when pressing a submit by email button?
Such as...
<label name>: <txtfield content>
First name: <txtfield content>
...etc..

After installing an application that was created using the Application Builder

Similar Messages

Maybe you are looking for