ASA 5505 as hw vpn client to PIX501 or ASA5505 w network extension mode
Hi!
We have been using a PIX 501 for a couple of years now to access a
local network with Cisco VPN software client. However we now need
access from another site with multiple users so I decided to buy two
ASA 5505 UL bundle to do the job. First i tried to just hook up the
new ASA at the remote site and connect to the PIX 501 with easy vpn.
In went fine. I configured the new ASA right from the box with the old
vpn profile settings and it worked right away. But as we also need the
remote site to be accessed from the main site (PIX side) i tried to
enable "network extension mode" but then the tunnel didnt work
anymore. it connects but no traffic is coming through. I set it back
to normal mode (only client) and it worked again.
Is there anything else I need to do to be able to use network
extension mode than just enabling it in ASDM ?
The samt thing happens when using two ASA 5505 the same way.
Software versions are:
PIX: 6.3
ASA 5505: 7.2.1 (used to be 7.2.2 but I had to downgrade because of a bug in 7.2.2 - vpnclient fails after reboot)
I also did try the latest 8.2 with very little success. Seemed a bit buggy.
Thanks,
Bjorn
Hi!
Thought I could add some info. Our Head unit is 192.168.1.1 and the connecting ASA 5505 is 192.168.10.1. When I try to ping a machine (192.168.1.201) from the remote site I get this in the ASA log:
With network extension mode
302020 192.168.1.201 192.168.10.2 Built ICMP connection for faddr 192.168.1.201/0 gaddr 192.168.10.2/512 laddr 192.168.10.2/512
With only client mode
302020 192.168.1.201 192.168.10.2 Built ICMP connection for faddr 192.168.1.201/0 gaddr 192.168.1.9/1 laddr 192.168.10.2/512
It seemes to me (quite the newbie here on ASA) that the unit does not handle the gateway address correctly when using network extension mode. The PC i use to ping from is 192.168.10.2.
Any ideas from the experts ?
Regards,
B
Similar Messages
-
Getting VPN from the VPN client to see into the host network
Hello
I am a real amateur here. I have configured a cisco VPN server, group and user on an SRP527W, ADSL2+ AnnexA, 802.11n ETSI, 2FXS/1FXO. I can connect from my PC with the Cicso VPN client on it (I get the banner) but I cannot ping into the local network at all. Once I do get in I will be using shares to work on files or VNC to take over a CAD workstation.
I am sure I just have not set up something but I don't know where to look. My local network is 192.168.15.***
Please put me right.
My setup isHello Christopher
It appears that the VPN client must be on a separate network to any VLAN: If I try an address range matching a local VLAN I get this: -
Cisco ASA 5505 AnyConnect SSL VPN problem
Hi!
I have a small network, wiht ASA 5505, 8.4:
Inside network: 192.168.2.0/24
Outside: Static IP
I would like to deploy a SSL AnyConnect setup.
The state:
-I give the correct IP from my predefined VPN pool (10.10.10.0/24).
But, could not reach any resource, could not ping too. My host has given 10.10.10.1 IP, and I had a GW: 10.10.10.2. Where is this GW from?
Could you help me?
Here is my config (I omitted my PUBLIC IP, and GW):
Result of the command: "show running-config"
: Saved
ASA Version 8.4(4)1
hostname valamiASA
domain-name valami.local
enable password OeyyCrIqfUEmzen8 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 12
interface Vlan1
description LAN
no forward interface Vlan12
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
description WAN
nameif outside
security-level 0
ip address MY_STATIC_IP 255.255.255.248
interface Vlan12
description Vendegeknek a valamiHotSpot WiFi-hez
nameif guest
security-level 100
ip address 192.168.4.1 255.255.255.0
management-only
ftp mode passive
clock timezone GMT 0
dns domain-lookup inside
dns domain-lookup outside
dns domain-lookup guest
dns server-group DefaultDNS
name-server 62.112.192.4
name-server 195.70.35.66
domain-name valami.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network inside-net
subnet 192.168.2.0 255.255.255.0
object network guest-net
subnet 192.168.3.0 255.255.255.0
object network NETWORK_OBJ_192.168.2.128_25
subnet 192.168.2.128 255.255.255.128
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object icmp
access-list global_access extended permit object-group DM_INLINE_PROTOCOL_3 any any
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_2 any any
access-list outside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu guest 1500
ip local pool valami_vpn_pool 10.10.10.1-10.10.10.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
no asdm history enable
arp timeout 14400
object network inside-net
nat (inside,outside) dynamic interface
object network guest-net
nat (guest,outside) dynamic interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group global_access global
route outside 0.0.0.0 0.0.0.0 MY_STATIC_GW 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa local authentication attempts max-fail 16
http server enable
http 192.168.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable inside
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_valami_VPN internal
group-policy GroupPolicy_valami_VPN attributes
wins-server value 192.168.2.2
dns-server value 192.168.2.2
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelall
default-domain value valami.local
webvpn
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect ask enable default anyconnect timeout 30
customization none
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information.
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group valami_VPN type remote-access
tunnel-group valami_VPN general-attributes
address-pool valami_vpn_pool
default-group-policy GroupPolicy_valami_VPN
tunnel-group valami_VPN webvpn-attributes
group-alias valami_VPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:d54de340bb6794d90a9ee52c69044753
: endFirst of all thanks your link.
I know your notes, but i don't understand 1 thing:
if i check nat exemption in the anyconnect wizad, why should i make nat exemption rule?
A tried creating a roule, but it is wrong.
My steps (on ASDM):
1: create network object (10.10.10.0/24), named VPN
2: create nat rule: source any, destination VPN, protocol any
Here is my config:
Result of the command: "show running-config"
: Saved
ASA Version 8.4(4)1
hostname companyASA
domain-name company.local
enable password OeyyCrIqfUEmzen8 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 12
interface Vlan1
description LAN
no forward interface Vlan12
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
description WAN
nameif outside
security-level 0
ip address 77.111.103.106 255.255.255.248
interface Vlan12
description Vendegeknek a companyHotSpot WiFi-hez
nameif guest
security-level 100
ip address 192.168.4.1 255.255.255.0
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns domain-lookup inside
dns domain-lookup outside
dns domain-lookup guest
dns server-group DefaultDNS
name-server 62.112.192.4
name-server 195.70.35.66
domain-name company.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network inside-net
subnet 192.168.2.0 255.255.255.0
object network guest-net
subnet 192.168.3.0 255.255.255.0
object network NETWORK_OBJ_192.168.2.128_25
subnet 192.168.2.128 255.255.255.128
object network WEBSHOP
host 192.168.2.2
object network INSIDE_HOST
host 10.100.130.5
object network VOIP_management
host 192.168.2.215
object network Dev_1
host 192.168.2.2
object network Dev_2
host 192.168.2.2
object network RDP
host 192.168.2.2
object network Mediasa
host 192.168.2.17
object network VOIP_ePhone
host 192.168.2.215
object network NETWORK_OBJ_192.168.4.0_28
subnet 192.168.4.0 255.255.255.240
object network NETWORK_OBJ_10.10.10.8_29
subnet 10.10.10.8 255.255.255.248
object network VPN
subnet 10.10.10.0 255.255.255.0
object network VPN-internet
subnet 10.10.10.0 255.255.255.0
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object icmp
access-list global_access extended permit object-group DM_INLINE_PROTOCOL_3 any any
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_2 any any
access-list outside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu guest 1500
ip local pool company_vpn_pool 10.10.10.10-10.10.10.15 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
no asdm history enable
arp timeout 14400
nat (any,any) source static any any destination static VPN VPN
nat (inside,outside) source static inside-net inside-net destination static VPN VPN
object network inside-net
nat (inside,outside) dynamic interface
object network guest-net
nat (guest,outside) dynamic interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group global_access global
route outside 0.0.0.0 0.0.0.0 77.111.103.105 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa local authentication attempts max-fail 16
http server enable
http 192.168.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable inside
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_company_VPN internal
group-policy GroupPolicy_company_VPN attributes
wins-server value 192.168.2.2
dns-server value 192.168.2.2
vpn-tunnel-protocol l2tp-ipsec
split-tunnel-policy tunnelall
default-domain value company.local
webvpn
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect ask enable default anyconnect timeout 30
customization none
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information.
group-policy GroupPolicy_VPN internal
group-policy GroupPolicy_VPN attributes
wins-server none
dns-server value 62.112.192.4 195.70.35.66
vpn-tunnel-protocol ssl-client
default-domain value company.local
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group company_VPN type remote-access
tunnel-group company_VPN general-attributes
address-pool company_vpn_pool
default-group-policy GroupPolicy_company_VPN
tunnel-group company_VPN webvpn-attributes
group-alias company_VPN enable
tunnel-group VPN type remote-access
tunnel-group VPN general-attributes
address-pool company_vpn_pool
default-group-policy GroupPolicy_VPN
tunnel-group VPN webvpn-attributes
group-alias VPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect icmp error
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:33ee37a3722f228f9be9b84ef43f731e
: end
Could you give me a CLI-code?
(or ASDM steps). -
Cisco ASA 5505 - 2 questions - VPN Licensing; Routing
Hi,
I have a client that has a Cisco ASA 5505 security appliance. Currently it is setup as a "proof of concept" for clientless browser-based SSL VPN. The device came with 2 licenses for this service, and we need to increase that somewhere between 10-25 users. 25 users is the max on this device I believe.
I have searched Cisco.com and tried Googling the ASA 5505 for licensing but I can't find the correct license that I need for this.
The second question I have is routing capability. We have a WAN connection to another branch of the computer from this location where the ASA 5505 is located. A Cisco 2851 is used for this connection. We are wanting to bring in a high speed Internet connection for the VPN access and Internet access. What I need to know is can we put the WAN and Internet connections behind the ASA 5505 and have that route appropriately to the branch WAN for that traffic and all other traffic to the Internet?
Thanks!
--KentHi Kent,
Thank you for your question. This community is for Cisco Small Business products and your question is in reference to a Cisco Elite/Classic product. Please post your question in the Cisco NetPro forums located here: http://forums.cisco.com/eforum/servlet/NetProf?page=main (http://forums.cisco.com/eforum/servlet/NetProf?page=main) This forum has subject matter experts on Cisco Elite/Classic products that may be able to answer your question.
Regards,
David Dunlap
SBSC Engineer -
Hello all thanks for looking,
I need to know how to setup my cisco asa 5505 as a vpn client to services like HMA or privateinternet and other paid VPN services. If someone else has already written a guide to this then that would be great. What I want to do is route all my secure traffice through the asa and have it go across the internet as encrypted VPN stuff and have my other stuff that does not need to be encrypted just go through to my other router.
Thanks in advance,If your remote end of the services in question support IPsec IKEv1 as the VPN type then, yes - the 5505 can be a client for that service. At that point it looks like a regular LAN-LAN VPN which is documented in many Cisco and 3rd party how-to documents.
-
Hello, I have been trying to configure a VPN with Cisco Asa 5505 and Cisco VPN client 5.X for 3 weeks and I am not being able to accomplish it, so I decided to reset to factory defaults and start over again.
I used ASDM 6.4 VPN wizard to configure it (I selected exempt local network from NAT and enabled split tunneling, but I have tried other combinations as well).
Tunnel seems to be established properly since I do see an endpoint while using 'sh crypto isakmp sa' but 'sh crypto ipsec sa' shows no packets encrypted or decrypted, so VPN is not working as expected. I can't ping or rdp to internal LAN:
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
The running-config it created is:
ciscoasa# sh run
: Saved
ASA Version 8.4(2)
hostname ciscoasa
enable password XXXX encrypted
passwd XXXX encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.16.1.254 255.255.0.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ADSL_Telefonica
ip address pppoe setroute
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network NETWORK_OBJ_10.0.0.0_24
subnet 10.0.0.0 255.255.255.0
object network NETWORK_OBJ_172.16.0.0_16
subnet 172.16.0.0 255.255.0.0
access-list test_splitTunnelAcl standard permit 172.16.0.0 255.255.0.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
ip local pool test 10.0.0.1-10.0.0.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_16 NETWORK_OBJ_172.16.0.0_16 destination static NETWORK_OBJ_10.0.0.0_24 NETWORK_OBJ_10.0.0.0_24 no-proxy-arp route-lookup
object network obj_any
nat (inside,outside) dynamic interface
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 172.16.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 172.16.0.0 255.255.0.0 inside
telnet timeout 55
ssh 172.16.0.0 255.255.0.0 inside
ssh timeout 55
console timeout 0
vpdn group ADSL_Telefonica request dialout pppoe
vpdn group ADSL_Telefonica localname adslppp@telefonicanetpa
vpdn group ADSL_Telefonica ppp authentication pap
vpdn username adslppp@telefonicanetpa password *****
dhcpd auto_config outside
dhcpd address 172.16.2.2-172.16.2.129 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy test internal
group-policy test attributes
dns-server value 172.16.1.1
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value test_splitTunnelAcl
username test password XXXXXX encrypted privilege 0
username test attributes
vpn-group-policy test
username ignacio password XXXXXXX encrypted
tunnel-group test type remote-access
tunnel-group test general-attributes
address-pool test
default-group-policy test
tunnel-group test ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:c8935bd572dfd37e81c6aa9f9dc8207c
: end
Thank you very much for your helpYes, it was a VPN client problem. I was doing test with a WWAN card and it seems it is not compatible with windows 7.
• The VPN Client on Windows 7 does not support WWAN devices (also called wireless data cards).
I should have read Release Notes before. Thank you very much for your help and effort. -
I have a customer running Cisco VPN client 5,0xx on a network behind a Cisco ASA 5505 router set up as a VPN server. He can connect to the remote (external) network, but cannot browse the remote network. Are there any special settings needed on the ASA 5505 to allow vpn client traffic through?
Maybe you need to enable Nat-traversal on your VPN Headend device.
Crypto isakmp Nat-t
HTH
Saju -
ASA 5505 IPSEC VPN connected but can't access to LAN
ASA : 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
VPN Pool: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to setup IPSEC VPN via ASDM; i just simply run the Wizards, setup vpnpool, split tunnelling,etc.
I can connect to the ASA by using cisco VPN client and internet works fine on the local PC, but it cannot access to the LAN (can't ping. can't remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile i created worked fine.
Below is my configure, do I mis-configure anything?
ASA Version 8.2(5)
hostname asatest
domain-name XXX.com
enable password 8Fw1QFqthX2n4uD3 encrypted
passwd g9NiG6oUPjkYrHNt encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.1.1.253 255.255.252.0
interface Vlan2
nameif outside
security-level 0
ip address XXX.XXX.XXX.XXX 255.255.255.240
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns server-group DefaultDNS
domain-name vff.com
access-list vpntest_splitTunnelAcl standard permit 10.1.0.0 255.255.252.0
access-list inside_nat0_outbound extended permit ip 10.1.0.0 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
logging enable
logging timestamp
logging trap warnings
logging asdm informational
logging device-id hostname
logging host inside 10.1.1.230
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 172.16.10.1-172.16.10.254 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server AD protocol nt
aaa-server AD (inside) host 10.1.1.108
nt-auth-domain-controller 10.1.1.108
http server enable
http 10.1.0.0 255.255.252.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.1.0.0 255.255.252.0 inside
ssh timeout 20
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy vpntest internal
group-policy vpntest attributes
wins-server value 10.1.1.108
dns-server value 10.1.1.108
vpn-tunnel-protocol IPSec l2tp-ipsec
password-storage disable
ip-comp disable
re-xauth disable
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpntest_splitTunnelAcl
default-domain value XXX.com
split-tunnel-all-dns disable
backup-servers keep-client-config
address-pools value vpnpool
username admin password WeiepwREwT66BhE9 encrypted privilege 15
username user5 password yIWniWfceAUz1sUb encrypted privilege 5
username user3 password umNHhJnO7McrLxNQ encrypted privilege 3
tunnel-group vpntest type remote-access
tunnel-group vpntest general-attributes
address-pool vpnpool
authentication-server-group AD
authentication-server-group (inside) AD
default-group-policy vpntest
strip-realm
tunnel-group vpntest ipsec-attributes
pre-shared-key BEKey123456
peer-id-validate nocheck
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command dynamic-filter
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege clear level 3 mode exec command dynamic-filter
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: endI change a Machine's gateway to this ASA and capture again, now we can see some reply.
All ohter PCs and switches gateway are point to another ASA, maybe that's the reason why i didn't work?
what's the recommanded way to make our LAN to have two 2 gateways(for load balance or backup router, etc)?
add two gateways to all PCs and swtichwes?
1: 18:15:48.307875 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
2: 18:15:49.777685 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
3: 18:15:51.377147 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
4: 18:15:57.445777 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
5: 18:15:58.856324 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
6: 18:16:00.395090 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
7: 18:16:06.483464 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
8: 18:16:08.082805 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
9: 18:16:09.542406 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
10: 18:16:20.640424 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
11: 18:16:20.642193 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
12: 18:16:21.169607 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
13: 18:16:21.171210 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
14: 18:16:22.179556 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
15: 18:16:22.181142 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
16: 18:16:23.237673 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
17: 18:16:23.239291 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
18: 18:16:27.676402 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
19: 18:16:29.246935 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
20: 18:16:30.676921 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
21: 18:16:49.539660 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
22: 18:16:54.952602 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
23: 18:17:04.511463 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request -
Hi! First of all I appologize for posting a similar question in another forum. I think this one is the right place.
Im trying to connect to a PIX 501 with easy vpn in nem mode with a ASA 5505. Currently running 7.2.2-22 (had to download a interim release due to dhcp problems with the ISP in 7.2.2) and ASDM 5.2.
The problem is that when using nem mode i cannot ping the other side at all. When using client mode this works fine but i need the two way traffic.
Our Head unit is 192.168.1.1 and the connecting ASA 5505 is 192.168.10.1. When I try to ping a machine (192.168.1.201) from the remote site I get this in the ASA log:
With network extension mode
302020 192.168.1.201 192.168.10.2 Built ICMP connection for faddr 192.168.1.201/0 gaddr 192.168.10.2/512 laddr 192.168.10.2/512
With only client mode
302020 192.168.1.201 192.168.10.2 Built ICMP connection for faddr 192.168.1.201/0 gaddr 192.168.1.9/1 laddr 192.168.10.2/512
It seemes to me that the ASA sets an incorrect gateway address in nem mode ?
The PIX 501 has been working fine for some years with software clients connecting.
Any ideas ?
Thanks!When configured in Easy VPN Network Extension Mode, the ASA 5505 does not hide the IP addresses of local hosts by substituting a public IP address. Therefore, hosts on the other side of the VPN connection can communicate directly with hosts on the local network.
Try this link:
http://www.cisco.com/en/US/docs/security/asa/asa72/configuration/guide/site2sit.html -
ASA 5505 & VPN Cellular connection
We have a ASA 5505 setup with VPN and using Cisco client 5.0. The VPN works without a problem if we use normal internet access (from home, motel, etc). However if we use a cellular wi-fi hotspot or tether a phone it will connect to the vpn but will not allow us to get on the office network. Anyone have this problem or know a solution
Hello greentw1972,
I have ran in to this issue several times. This is mainly caused by Cisco VPN client's compatibility issues with the 3G-Dongle/Tethering-device. I have seen several workarounds for this but the best one I have found is to use a Open source vpn client.
I have used Shrewsoft VPN client and it has worked nicely without any issues so far
Find the links below for further information.
The 3rd link will show you how exactly you need to transfer information from Cisco VPN client to Shrewsoft client.
Shrewsoft latest VPN client download link : www.shrew.net/download/vpn/vpn-client-2.2.0-rc-2.exe
Shrewsoft Web site : www.shrew.net
Installation instruction as Cisco VPN alternative : http://superuser.com/questions/312947/how-to-configure-shrewsoft-vpn-to-connect-to-cisco-vpn-server
Plese rate this post if helpful -
Problem with ASA 5505 VPN config
Hi to all,
I have a problem with ASA 5505 remote access vpn. I have site-to-site VPN and I need that my VPN clients can access IP subnets that I have behind site-to-site VPN. All that I have tried I get and error to my log “Flow is a loopback”.
So what I need : for example I need that vpn client with ip 10.0.0.1 can go to 192.168.1.2
My config:
access-list Test_splitTunnelAcl standard permit host 10.0.2.3
access-list Test_splitTunnelAcl standard permit host 10.0.2.4
access-list Test_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list nonat_outside extended permit ip 10.0.0.0 255.255.255.0 192.168.1.0 255.255.255.0
ip local pool VPN_Client_Pool2 10.0.0.1-10.0.0.200 mask 255.255.255.0
nat (outside) 0 access-list nonat_outside
nat (outside) 1 10.0.0.0 255.255.255.0
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Test_splitTunnelAcl
Site-to-Site:
crypto map outside_map 3 set peer 195.233.x.x
access-list outside_3_cryptomap extended permit ip object-group DM_INLINE_NETWORK_2 object-group DM_INLINE_NETWORK_4
object-group network DM_INLINE_NETWORK_2
network-object 10.0.2.0 255.255.255.0
network-object 10.0.3.0 255.255.255.0
object-group network DM_INLINE_NETWORK_4
network-object host 192.168.2.70
network-object host 192.168.3.55
network-object 192.168.1.0 255.255.255.0
I hope that someone can post an answer and solve my problemA few things are required:
1) You don't need the following 2 lines, so it can be removed:
nat (outside) 0 access-list nonat_outside
nat (outside) 1 10.0.0.0 255.255.255.0
2) On the ASA, you need to configure:
same-security-traffic permit intra-interface
3) Object group: DM_INLINE_NETWORK_2 needs to include 10.0.0.0/24
4) On the remote lan-to-lan end, the crypto ACL also needs to include 10.0.0.0/24 as the destination subnet.
5) The NAT exemption (NONAT) on the remote lan-to-lan end also needs to include 10.0.0.0/24 as the destination subnet.
Hope that will resolve your problem. -
Cisco VPN 3002 to Cisco ASA 5505
I want to remove a Cisco VPN 3002 Hardware client and replace it with a Cisco ASA 5505. Is there a way to do this? I want to have the remote user and group authentication and no split tunneling.?
Thanks for your help.Sure can.
Here is a sample configuration for ASA5505 acting as a remote hardware easy vpn client (like the VPN3002):
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00808a61f4.shtml
If you don't want split tunneling, then I assume that it is in PAT/client mode instead of NEM mode as above sample configuration.
You can just change the "vpnclient mode network-extension-mode" to "vpnclient mode client-mode"
Hope this helps. -
ASA 5505 VPN can't access connected network
I have an ASA 5505 with ipsec VPN configured on it. I am able to connect to the ASA but I can't ping a connected network. I get a dhcp assigned address in the network I am trying to reach but can't access that network on Vlan5. Please help.
I attached the config.I think final questions, can you have two nat statements that point to the same acl ie.
access-list no_nat extended permit ip 192.168.9.0 255.255.255.0 192.168.0.0 255.255.255.0
access-list no_nat extended permit ip 192.168.9.0 255.255.255.0 172.31.1.0 255.255.255.0
access-list no_nat extended permit ip 192.168.5.0 255.255.255.0 192.168.5.0 255.255.255.0
nat (inside) 0 access-list no_nat
nat (inside) 1 192.168.9.0 255.255.255.0
nat (fw-civic) 0 access-list no_nat
nat (fw-civic) 1 192.168.5.0 255.255.255.0
Or do I need to create a new acl for the fw-civic interface?
Thanks -
Good day all,
this is my network setup in one of our branch office.
LAN ---- inside(192.168.44.1) ASA outside(10.103.1.159) ---- ISP
The ISP is doing NAT and give us a IP via DHCP (PPPoE dial-in).
Now we want to set up the branch ASA to act as EZVPN client.
But when I add the config for example this one:
vpnclient server xxx.xxx.xxx.xxx
vpnclient mode network-extension-mode
vpnclient nem-st-autoconnect
vpnclient vpngroup eznemgroup password eznemgrouppass
vpnclient username eznemuser1 password eznemuser1pass
vpnclient enable
We loss Internet connectivity after the last command << vpnclient enable >>.
Problem is that we can only configure the ASA remotely.
Is this a normal behaviour for VPN client setup? I found nothing in the documentation?
Thanks for your feedback!
Brgds,
MarkusHi Guys,
still struggling with the EZVPN setup.
This is instantaneous setup at the moment.
LAN ---- inside-(192.168.44.1) ASA outside-(DHCP private IP) ---- (private IP)-ISP Router-(public IP)
The ISP blocks UDP/500 and UDP/4500 so there is no way to setup a site-2-site VPN via IPsec.
So we tried to setup the ASA5505 as EZVPN client and configured to use TCP over IPsec. But without success. I think the problem is the private IP on our outside interface. Has someone face the same problem?
Thanks Markus -
Access Site to Site Networks behind Cisco ASA thru VPN Client
I have configured remote access thru asa for vpn clients to our main network. I can ping the required networks from vpn client. Internally I can ping remote network thru our sonicwall site to site vpn. I however cannot ping the remote network from the vpn client. I've added the network in the configuration on the ASA that I am trying to connect to. Any ideas what I can do so I can connect to Site B thru my vpn client connecting to Site A?
Thanks,
MattHello, matt0000111111.
Did you add a VPN clients network to the sit-to-site VPN settings and to the NAT list (if nat exist at the interfaces at site-to-site vpn)?
Maybe you are looking for
-
Budgeting on account & cost center level
Hi ALL, My company is planning to implement SAP in the near future and I'm taking the SAP course now. According to what SAP instrcutor said, budgeting cannot be done on account & cost center level. In my company, our current practice is to record all
-
Installing ODBC Driver for Windows Server 2008 64 bit
I have a new Windows 2008 server 64 bit in which the Oracle ODBC is missing. We are on Oracle 10.2. It looks like I need to install the developer suite first in order to get tnsnames and sql plus, but I can find only the 32 bit version. Could someone
-
Having a problem after re-install my macbook
I am having problem with my macbook. I had both window and OS 10.4 on my macbook, and I was planning to make it back into a single system with just OS on it. However, I did it kind of backward, I put in the install disc and have a new OS on the Mac s
-
Computer not authorized message for purchases from itunes
I had my computer re-built and itunes does not recognize that I purchased songs. I have "re" - authorized the computer but keep getting the same message. Also, when purchasing, I used an old email account that I cannot no longer access. Suggestio
-
Some given following requirement cloud, Can able to fullfill in cloud?
respected sir, we have no of client in area of micro finance , we are planning to shift the our application in cloud. but , we have some query like 1) while access the database or web services , how many type of security level are cloud support.? 2)