OSPF PTP with ASA
Hello
I am trying to bring up a L3 PTP between an ASA and a 6500 running IOS. The ASA is in routed mode configured for OSPF. On the ASA I configure the interface to the 6500 with an IP address and define the network type as point-to-point. I add that network to the OSPF process configuration. Likewise on the 6500 I configure the interface as a L3 interface with IP and network type as point-to-point. I add the same /30 network to that OSPF process. I can ping across the /30 both ways but the adjacency is not forming. The ASA debugs show the hello coming from the correct 6500 interface. However the ASA can't find the 6500 interface. The debug indicates "cannot locate nbr x.x.x.x (ip address of 6500 interface).
When I remove the "ospf network point-to-point nonbroadcast" command on the ASA the adjacency does form. However, on the ASA side it's "2way/drother" and on the 6500 side "full". The LSDB's look good. But the 6500 is not injecting the routes advertised from the ASA into the routing table.
Thoughts? I suspect I am missing a concept or simple command. As far as I can tell this is a supported configuration on the ASA. But have not been able to find any point-to-point configuration examples.
Any information is much appreciated.
Thanks
Chuck
On the ASA the "non-broadcast" option is required. When I try to leave it off I get a "command incomplete" message.
There are no other options available so I used "ospf network point-to-point non-broadcast" option.
On the 6500 IOS switch I can simply put in "ip ospf network point-to-point" with no further options. Here the "non-broadcast" option is not available even if I wanted it.
So with the ASA using "ospf network point-to-point nonbroadcast" and the 6500 IOS using "ip ospf network point-to-point" I can't get the adjacency up. Both network types are listed as "POINT-TO-POINT" for each interface.
Any further thougths anyone? Is there a different command on the ASA that doesn't require the non-broadcast option?
Chuck
Similar Messages
-
Problem with ASA 5505 VPN config
Hi to all,
I have a problem with ASA 5505 remote access vpn. I have site-to-site VPN and I need that my VPN clients can access IP subnets that I have behind site-to-site VPN. All that I have tried I get and error to my log “Flow is a loopback”.
So what I need : for example I need that vpn client with ip 10.0.0.1 can go to 192.168.1.2
My config:
access-list Test_splitTunnelAcl standard permit host 10.0.2.3
access-list Test_splitTunnelAcl standard permit host 10.0.2.4
access-list Test_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list nonat_outside extended permit ip 10.0.0.0 255.255.255.0 192.168.1.0 255.255.255.0
ip local pool VPN_Client_Pool2 10.0.0.1-10.0.0.200 mask 255.255.255.0
nat (outside) 0 access-list nonat_outside
nat (outside) 1 10.0.0.0 255.255.255.0
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Test_splitTunnelAcl
Site-to-Site:
crypto map outside_map 3 set peer 195.233.x.x
access-list outside_3_cryptomap extended permit ip object-group DM_INLINE_NETWORK_2 object-group DM_INLINE_NETWORK_4
object-group network DM_INLINE_NETWORK_2
network-object 10.0.2.0 255.255.255.0
network-object 10.0.3.0 255.255.255.0
object-group network DM_INLINE_NETWORK_4
network-object host 192.168.2.70
network-object host 192.168.3.55
network-object 192.168.1.0 255.255.255.0
I hope that someone can post an answer and solve my problemA few things are required:
1) You don't need the following 2 lines, so it can be removed:
nat (outside) 0 access-list nonat_outside
nat (outside) 1 10.0.0.0 255.255.255.0
2) On the ASA, you need to configure:
same-security-traffic permit intra-interface
3) Object group: DM_INLINE_NETWORK_2 needs to include 10.0.0.0/24
4) On the remote lan-to-lan end, the crypto ACL also needs to include 10.0.0.0/24 as the destination subnet.
5) The NAT exemption (NONAT) on the remote lan-to-lan end also needs to include 10.0.0.0/24 as the destination subnet.
Hope that will resolve your problem. -
Remote access VPN with ASA 5510 using DHCP server
Hi,
Can someone please share your knowledge to help me find why I am not able to receive an IP address on remote access VPN connection while I can get an IP address on local DHCP pool?
I am trying to setup remote access VPN with ASA 5510. It works with local dhcp pool but doesn't seem to work when I tried using an existing DHCP server. It is being tested in an internal network as follows:
ASA Version 8.2(5)
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.6.0.12 255.255.254.0
ip local pool testpool 10.6.240.150-10.6.240.159 mask 255.255.248.0 !(worked with this)
route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
crypto ipsec transform-set FirstSet esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map dyn1 1 set transform-set FirstSet
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface inside
crypto isakmp enable inside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
vpn-addr-assign aaa
vpn-addr-assign dhcp
group-policy testgroup internal
group-policy testgroup attributes
dhcp-network-scope 10.6.192.1
ipsec-udp enable
ipsec-udp-port 10000
username testlay password *********** encrypted
tunnel-group testgroup type remote-access
tunnel-group testgroup general-attributes
default-group-policy testgroup
dhcp-server 10.6.20.3
tunnel-group testgroup ipsec-attributes
pre-shared-key *****
I got following output when I test connect to ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDO
4024 bytesR copied in 3.41 0 secs (1341 by(tes/sec)13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ISA_KE payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received DPD VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: True Aggressive Mode: False
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received NAT-Traversal ver 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, Received Cisco Unity client VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, Connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing IKE SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA Proposal # 1, Transform # 9 acceptable Matches global IKE entry # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ISAKMP SA payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for Responder...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing ID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Computing hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing Cisco Unity VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing xauth V6 VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Traversal VID ver 02 payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing Fragmentation VID + extended capabilities payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + HASH (8) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + HASH (8) + NOTIFY (11) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Computing hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing NAT-Discovery payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, computing NAT Discovery hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Processing IOS/PIX Vendor ID payload (version: 1.0.0, capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing VID payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Received Cisco Unity client VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
kens-mgmt-012# P = 10.15.200.108, Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=d4ca48e4) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=d4ca48e4) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Processing MODE_CFG Reply attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary WINS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary WINS = cleared
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: IP Compression = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling Policy = Disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Browser Proxy Setting = no-modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Browser Proxy Bypass Local = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, User (testlay) authenticated.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=6b1b471) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=6b1b471) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Processing cfg ACK attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=49ae1bb8) with payloads : HDR + HASH (8) + ATTR (14) + NONE (0) total length : 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): Enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Processing cfg Request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for IPV4 net mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for DNS server address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for WINS server address!
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Received unsupported transaction mode attribute: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Save PW setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Default Domain Name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Split Tunnel List!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Client Browser Proxy Setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for backup ip-sec peer list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Client Smartcard Removal Disconnect Setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for Application Version!
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Client Type: WinNT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for DHCP hostname for DDNS is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: Received request for UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Duplicate Phase 2 packet detected. No last packet to retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIVED Message (msgid=b04e830f) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Duplicate Phase 2 packet detected. No last packet to retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE received response of type [] to a request from the IP address utility
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Cannot obtain an IP address for remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE TM V6 FSM error history (struct &0xd8030048) <state>, <event>: TM_DONE, EV_ERROR-->TM_BLD_REPLY, EV_IP_FAIL-->TM_BLD_REPLY, NullEvent-->TM_BLD_REPLY, EV_GET_IP-->TM_BLD_REPLY, EV_NEED_IP-->TM_WAIT_REQ, EV_PROC_MSG-->TM_WAIT_REQ, EV_HASH_OK-->TM_WAIT_REQ, NullEvent
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE AM Responder FSM error history (struct &0xd82b6740) <state>, <event>: AM_DONE, EV_ERROR-->AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL-->AM_TM_INIT_MODECFG_V6H, NullEvent-->AM_TM_INIT_MODECFG, EV_WAIT-->AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG-->AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK-->AM_TM_INIT_XAUTH_V6H, NullEvent-->AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b terminating: flags 0x0945c001, refcnt 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending delete/delete with reason message
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing blank hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing IKE delete payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing qm hash payload
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SENDING Message (msgid=9de30522) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 80
Regards,
LayFor RADIUS you need a aaa-server-definition:
aaa-server NPS-RADIUS protocol radius
aaa-server NPS-RADIUS (inside) host 10.10.18.12
key *****
authentication-port 1812
accounting-port 1813
and tell your tunnel-group to ask that server:
tunnel-group VPN general-attributes
authentication-server-group NPS-RADIUS LOCAL
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni -
How Can i Use two Different Public IP Addresses no my DMZ with ASA Firewall.
How To Using Two Different Public IP Address on My DMZ with ASA 5520
Postado por jorge decimo decimo em 28/Jan/2013 5:51:28
Hi everyone out there.
can any one please help me regarding this situation that im looking for a solution
My old range of public ip address are finished, i mean (the 41.x.x.0 range)
So now i still need to have in my DMZ another two servers that will bring some new services.
Remember that those two server, will need to be accessable both from inside and from outside users (Internet users) as well.
So as i said, my old range of public ip address is finished and we asked the ISP to gives some additional public
ip address to address the need of the two new servers on DMZ. and the ISP gave us the range of 197.216.1.24/29
So my quation is, on reall time world (on the equipment) how can i Use two different public ip address on the same DMZ
on Cisco ASA 5520 v8??
How my configuration should look like?
I was told about implementing static nat with Sub Interfaces on both Router and ASA interface
Can someone please do give me a help with a practical config sample please. i can as well be reached at [email protected]
attached is my network diagram for a better understanding
I thank every body in advance
JorgeHi,
So looking at your picture you have the original public IP address range configured on the OUTSIDE and its used for NAT for different servers behind the ASA firewall.
Now you have gotten a new public IP address range from the ISP and want to get it into use.
How do you want to use this IP address range? You want to configure the public IP addresses directly on the servers or NAT them at the ASA and have private IP addresses on the actual servers (like it seems to be for the current server)?
To get the routing working naturally the only thing needed between your Router and Firewall would be to have a static route for the new public network range pointing towards your ASA OUTSIDE IP address. The routing between your Router and the ISP core could either be handled with Static Routing or Dynamic Routing.
So you dont really need to change the interface configuration between the Router and ASA at all. You just need a Static route pointing the new public IP address towards the ASA outside IP address.
Now when the routing is handled between the ISP - ISP/Your Router - Your Firewall, you can then consider how to use those IP addresses.
Do you want to use the public IP addresses DIRECTLY on the HOSTS behind the firewall?This would require you to either configure a new physical interface with the new public IP address range OR create a new subinterface with the new public IP addresses range AND then configure the LAN devices correspondingly to the chosen method on the firewall
Do you want to use the public IP addresses DIRECLTY on the ASA OUTSIDE as NAT IP addresses?This would require for you to only start configuring Static NAT for the new servers between the inside/dmz and outside interface of the ASA. The format would be no different from the previous NAT configuration other than for the different IP addresses ofcourse
Of the above ways
The first way is good because the actual hosts will have the public IP addresses. Therefore you wont run into problems with DNS when the LAN users are trying to access the server.
The second way is the one requiring the least amount of configurations/changes on the ASA. In this case though you might run into problem with DNS (to which I refer above) as the server actually has a private IP address but the public DNS might reply to the LAN hosts with a public IP address and therefore connections from LAN could fail. This is because LAN users cant connect to the servers OUTSIDE NAT IP address (unless you NAT the server to public IP address towards LAN also)
Hopefully the above was helpfull. Naturally ask more specific questions and I'll answer them. Hopefully I didnt miss something. But please ask more
I'm currently at Cisco Live! 2013 London so in the "worst case" I might be able to answer on the weekend at earliest.
- Jouni -
Tacacs+ access issue with ASA firewall after integrating with RSA SecureID
Hi,
In my earlier post, I raised the same question but let me rephrased it again. I have configured TACACS+ in cisco ASA firewall and able to access . But when I integrated it with RSA secure ID , I am not able to enter in enable mode. It is not accepting enable password nor RSA passcode. I have created enable_15 in ASA , ACS and RSA server but no luck.
Did any one face similar issue with ASA access ?
Rgds
SiddheshHi Siddesh,
In order to help you here, I need to know few things:
1.] Show run | in aaa
2.] When you enter enable password on ASA CLI, what error do you see on ACS > Monitoring and reports > AAA protocols > tacacs authentication > "look for the error message"
3.] Turn on the debugs on ASA "debug tacacs" and "debug aaa authentication" before you duplicate the problem.
~BR
Jatin Katyal
**Do rate helpful posts** -
NAC 4.9 CAS inband with ASA 8.6
We are working on a new deployment. The user logs in, the agent pops, and posture assessment happens. The screen for posture assessment closes at the test laptop. It acts like all is working. When we look at the inband user it shows as not having transitioned frm the auth the access VLAN. This is a simple install and the VLAN mapping is definitely there. Ideas?
Steve,
Here is a configuration guide for the ASA to CAS, its not the latest and greatest but this should work:
http://www.cisco.com/en/US/products/ps6128/products_configuration_example09186a008074d641.shtml
When referrring to L2 and L3 adjacent this is different with respect to VGW and RIP.
L2 and L3 refers to how the clients are positioned with respect to the CAS (not the CAM), are they being routed to the CAS untrusted interface or are they available on a vlan that the CAS can be a part of.
VGW and RIP refers to the operation of the CAS, this is similar to the operation of the ASA, when it comes to transparent vs routed mode (you can use both the on same CAS), VGW bridges the two networks together, and RIP routes the traffic around and requires static routing since the CAS does not support dynamic routing protocols.
You can use VGW by setting the group policy to route all tunneled traffic to an ip that is present on the trusted side of the CAS, also you can use the vlan attribute in the group-policy configuration to assign the remote users to a vlan which forces their traffic to flow through the CAS.
http://cisconac.blogspot.com/2007/07/vpn-deployments-with-asa-80.html
Thanks,
Tarik Admani
*Please rate helpful posts* -
Hi ALL,
Has any one configured a WLC with ASA as the gateway, I have 3 interface 70, 80 and 90 ( 70 is the management vlan ) in the WLC, with all the gateway in the ASA. But I can ping only the gateway for vlan 70 from my wlc, none of the other gateway's are reachable.
Let me know if any one have faced this issue before
Thanks
NikhiLProbably the other ASA interfaces are configured to be non pingable ? that's quite common.
-
we will deploy waas in branch with asa so we will make wccp redirect on asa as asa will terminate vpn with headoffice so we must use wccp on asa is there is any document of sample of configuration to configure wccp with asa
hi,
here is the link:
http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/dhcp.html#wp1094445
hope it will help -
Hello,
If an LSA is received by an OSPF router which is not Demand Circuit capable, will that LSA be installed in link state database?
ThanksHow can step 2 in the sequence description say that PE2-AS1 receives an OSPF route with the Down Bit already set? This comes from the CE.
I find this all very confusing when I check out these sequences - I thought only the PE router assigns Down Bit to LSA Type 3 routes?
All the other references I see show how PE1-AS1 would normally set the Down Bit as it is redistributed back into OSPF?
Thanks for your help - I feel I am getting closer. It is just this second step that is throwing me!
Cheers
Walter -
Hello guys,
I'm designing small-medium branch office (from 100 users scalable up to 500).
My idea was to build this around a pair of 6506-E switches (as collapsed core, utilizing VSS), then at each floor (1 floor = 100 users) have a stack of 3750 switches.
Now, to my question, I want a pair of security appliances, one per each breakout. I was looking at a possibility of putting ASA module into each 6500.
Is it possible, to use 10G X2 module, which are build into 6500's SUP as WAN interface and direct everything it receives on those ports directly into ASA? (I want to have all traffic which will come to the 6500 via SUP's X2 modules to pass through ASA before any further action will be taken).
As fair as I know in order to use VSS together with ASA modules in active/active mode (I will load balance through uplinks on both 6500) I need to use SUP 720-10G, am I right?
Thanks in advance for you insights.
MichalThanks guys. Appreciate your feedback!
I will most likely go for the option "Existing ASA 5540 with IPS module" . I hope the IPS module does not limit any bandwidth capability or processing issue of the ASA. My current throughput is 250 Mbps bidirectional.
After looking at the IPS option I am sloghly confused which one I need. Cisco website say:
"...adding the broad range of intrusion prevention and advanced antiworm services delivered by the IPS modules via the AIP SSM and AIP SSC, or the comprehensive malware protection and content security services enabled by the CSC SSM."
Do I need SSM only or both SSM and SSC or CSC SSM? How many module cana be installed on 5540?
Fawad -
Question about : Securing Networks with ASA Foundation (SNAF)
Dear All,
I would like to ask about the exam Securing Networks with ASA Foundation (SNAF) as below:
1- How i can download documents before i take exam? ( i mean did it have offline file?)
2- i was pass CCNA and CCDA already so can i continuous to take this exam?
I try to find ebook and offline file from Cisco website but it don't have....
Please let me know if you know this ...:)
best regards,
RechardThere's a quick reference book for SNAF. You can find it on the cisco press website. There's also an older book called "Cisco ASA: All-in-One Firewall, IPS, and VPN Adaptive Security Appliance". It's from 2005 but it's usefull.
After CCNA I'd recommend you to pass CCNA:Security before you take SNAF. It's needed both for ASA Specialist and for CCSP.
Good luck -
Syslog message OSPF: Send with youngest Key
I receive the following yslogmessage from my corerouter(Catalyst6509)
Nov 10 18:00:00 core-gw.uni-koeln.de 17708571: Nov 10 17:59:59 MET: OSPF: Send with youngest Key 0
Nov 10 18:00:00 core-gw.uni-koeln.de 17708572: Nov 10 18:00:00 MET: OSPF: Send with youngest Key 1
Nov 10 18:00:00 core-gw.uni-koeln.de 17708573: Nov 10 18:00:00 MET: OSPF: Send with youngest Key 0
Nov 10 18:00:00 core-gw.uni-koeln.de 17708574: Nov 10 18:00:00 MET: OSPF: Send with youngest Key 1
Nov 10 18:00:00 core-gw.uni-koeln.de 17708575: Nov 10 18:00:00 MET: OSPF: Send with youngest Key 1
What does it mean ?
How to resolve the problem ?
thanks in advance
ManfredSeems you have MD5 authentication enabled but different key IDs. Do you have more than one key configured on any interface?
Daniel Dib
CCIE #37149 -
DMVPN Configuration with ASA 5510 In Front of Cisco 877-K9 HUB Router
Hi Guys,
I'm in a mess, I have Cisco 877-K9 router which sits behind an ASA 5510 FW.
The Design :
Cisco 877-K9 DSL router (DSL with Static IP) ( DMVPN HUB )
||
ASA 5510 Firewall (Outside INT with Static IP / Inside INT LAN) (PAT & ACL)
||
Switch
||
LAN
Now my problem is, My Dmvpn configuration works just fine, I'm able to ping from my Cisco 877 to any Spoke & vise versa.
I'm also able to Ping from my LAN to any Spoke Tunnel IP, but Im not able to ping any LAN IP at Spoke site nor am I able to ping my LAN from any Spoke site.
I've googled alot but have come at designs where the ASA's are behind the Cisco Routers and not infront.
Any help in this regards is highly appreciated. I really need this to work. Attached are the config files....
Thanks,
Aj.Thanks to both of you guys for replying. I should've been more descriptive in my initial post, but just thought of getting more ideas.
All the troubleshooting was done before posting the problem, and to clearify the things, Please find below the results.
1) what RProtocol r u using?
a) It's OSPF
2) if ur using OSPF, try show ip route on the hub and spoke to verify the hub/spoke routes are learned via OSPF
a) I did the "show ip route" and bothe the HUB and Spokes get their routes defined
(on the HUB if I used "network 192.9.201.0 255.255.255.0 area 0" I coudln't get routes advertised on spokes)
(I changed to "redistribute static subnests" and I was able to get Hub routes advertised")
3) are your tunnels config correctly? try show crypto ipsec sa
a) They are as they should be and "show crypto ipsec sa" comes up with proper in/out encrypted data
4) on your hub'spoke do a debug ip icmp
a) Did that as well, and If I do a debug on a Spoke and ping from my HUB to that spoke on the tunnel IP, I get proper src/dest results, but If I ping from HUB to Spoke on a client IP behind the Spoke, It pings but does not show any result on the Spoke debug.
I'm able to ping all the Spoke's Tunnel IPs and clients behind the Spokes from the HUB router, but not from either the ASA nor the clients on my LAN.
Additional to the info above, Please also note :
I did notice something that, from my HUB router, which is also my DSL Modem, I'm unable to ping any clients behind the ASA.
So I guess I'm stuck on the point that My Cisco HUB is unable to talk to my LAN, If I can get the HUB to talk to the internal LAN, I would be able to ping clients on LAN from any Spoke or clients behind Spokes.
From HUB router I'm able to ping clients behind Spokes.
Does that give any Ideas ?
Thanks in Advance.
Aj. -
Good morning,
I'm having the following problem. I configured a ASA 5505 with VPN and a VPN Remote Access Site-to-site. Everything is working, but when I reload the ASA does not work anymore VPNs, Remote Access error 412 and the Site-to-site does not connect more to solve, I have to reset and reconfigure the ASA. This is happening dopo updating the ASA, I have version 842-k8 and asdm645-106.
Does anyone have any idea what can be?
Thank you.
Running-config:
: Saved
: Written by master at 10:34:14.839 BRDT Mon Oct 10 2011
ASA Version 8.4(2)
hostname ciscoasa
domain-name default.domain.invalid
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 172.16.0.140 255.255.252.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group gvt
ip address pppoe setroute
boot system disk0:/asa842-k8.bin
ftp mode passive
clock timezone BRST -3
clock summer-time BRDT recurring 2 Sun Oct 0:00 3 Sun Feb 0:00
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network NETWORK_OBJ_172.16.0.0_22
subnet 172.16.0.0 255.255.252.0
object network NETWORK_OBJ_172.16.0.128_26
subnet 172.16.0.128 255.255.255.192
object network NETWORK_OBJ_20.0.0.0_24
subnet 20.0.0.0 255.255.255.0
object network NETWORK_OBJ_172.16.11.0_24
subnet 172.16.11.0 255.255.255.0
object-group network obj_any
access-list 1 standard permit 172.16.0.0 255.255.252.0
access-list 1 standard permit 20.0.0.0 255.255.255.0
access-list outside_cryptomap extended permit ip 172.16.0.0 255.255.252.0 20.0.0.0 255.255.255.0
access-list outside_cryptomap_1 extended permit ip 172.16.0.0 255.255.252.0 172.16.11.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool pool 172.16.0.150-172.16.0.160 mask 255.255.252.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645-106.bin
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_172.16.0.128_26 NETWORK_OBJ_172.16.0.128_26 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_20.0.0.0_24 NETWORK_OBJ_20.0.0.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_172.16.11.0_24 NETWORK_OBJ_172.16.11.0_24 no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
route outside 172.16.11.0 255.255.255.0 187.16.33.131 10
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 172.16.0.0 255.255.252.0 inside
no snmp-server location
no snmp-server contact
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 189.11.56.237
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 2 match address outside_cryptomap_1
crypto map outside_map 2 set peer 187.16.33.131
crypto map outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 2 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn group gvt request dialout pppoe
vpdn group gvt localname *******@turbonetpro
vpdn group gvt ppp authentication pap
vpdn username *******@turbonetpro password *****
dhcpd auto_config outside
dhcpd address 172.16.0.144-172.16.1.143 inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy crv internal
group-policy crv attributes
dns-server value 172.16.0.253 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value 1
default-domain value crvnatural.com.br
group-policy GroupPolicy_189.11.56.237 internal
group-policy GroupPolicy_189.11.56.237 attributes
vpn-filter value 1
vpn-tunnel-protocol ikev1 ikev2
group-policy GroupPolicy_187.16.33.131 internal
group-policy GroupPolicy_187.16.33.131 attributes
vpn-filter value 1
vpn-tunnel-protocol ikev1 ikev2
username master password kWH7f2vqtjMEg2Yp encrypted
tunnel-group crv type remote-access
tunnel-group crv general-attributes
default-group-policy crv
dhcp-server 172.16.0.253
tunnel-group crv ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 189.11.**.*** type ipsec-l2l
tunnel-group 189.11.**.*** general-attributes
default-group-policy GroupPolicy_189.11.**.***
tunnel-group 189.11.**.*** ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key ****
ikev2 local-authentication pre-shared-key *****
tunnel-group 187.16.33.*** type ipsec-l2l
tunnel-group 187.16.33.*** general-attributes
default-group-policy GroupPolicy_187.16.33.***
tunnel-group 187.16.33.*** ipsec-attributes
ikev1 pre-shared-key ******
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:50ed6f55182534a2429d065a26e9b45c
: endDavid,
In order to understand why LDAP is not working run a "debug ldap 255" and then try to login or run a AAA test.
Attach the output to find out the issue.
Please check this out as well, to make sure that you have the correct settings:
ASA 8.0: Configure LDAP Authentication for WebVPN Users
HTH.
Portu. -
Remote Access VPN Problem with ASA 5505
After about ~1 year of having the Cisco VPN Client connecting to a ASA 5505 without any problems, suddenly one day it stops working. The client is able to get a connection to the ASA and browse the local network for only about 30 seconds after connection. After that, no access is available to the network behind the ASA. I tried everything that I can think of to try and troubleshoot the problem, but at this point I am just banging my head against a wall. Does anyone know what could cause this?
Here is the running cfg of the ASA
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password xxxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxx encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http **.**.***.*** 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
And here is the logs from the Cisco VPN Client when it browses, then fails to browse the network behind the ASA:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600026
Attempting to find a Certificate using Serial Hash.
2 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600027
Found a Certificate using Serial Hash.
3 09:44:55.693 10/01/13 Sev=Info/6 GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
4 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100002
Begin connection process
5 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100004
Establish secure connection
6 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
7 09:45:02.802 10/01/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
8 09:45:02.818 10/01/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
9 09:45:02.865 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
10 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
11 09:45:02.896 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
12 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
13 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
14 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
15 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
16 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
17 09:45:02.927 10/01/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
18 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
19 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 10/01/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end is NOT behind a NAT device
21 09:45:02.927 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 09:45:02.943 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 09:45:02.943 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 09:45:02.943 10/01/13 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 09:45:03.037 10/01/13 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
26 09:45:03.037 10/01/13 Sev=Info/4 CM/0x63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
28 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
29 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
30 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
31 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
32 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
33 09:45:03.083 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
34 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
35 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
36 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
37 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
38 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
39 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
40 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
41 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
42 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
43 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
45 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
46 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0x00002710
47 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
48 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
49 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
50 09:45:03.146 10/01/13 Sev=Info/4 CM/0x63100019
Mode Config data received
51 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
52 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
53 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
54 09:45:03.177 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
55 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
56 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 1 seconds, setting expiry to 86399 seconds from now
57 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
58 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
59 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
60 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to **.**.***.***
61 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=967A3C93 OUTBOUND SPI = 0xAAAF4C1C INBOUND SPI = 0x3EBEBFC5)
62 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xAAAF4C1C
63 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 10/01/13 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
66 09:45:03.896 10/01/13 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
67 09:45:03.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 10/01/13 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
69 09:45:07.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**.**.***.*** 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 10/01/13 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
71 09:45:07.912 10/01/13 Sev=Info/4 CM/0x6310001A
One secure connection established
72 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 96.11.251.149. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 10/01/13 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
75 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
76 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
77 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x1c4cafaa into key list
78 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
79 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xc5bfbe3e into key list
80 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
81 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
83 09:45:13.459 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
84 09:45:13.459 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205276
85 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
86 09:45:13.474 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
87 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205276, seq# expected = 107205276
88 09:45:15.959 10/01/13 Sev=Info/4 IPSEC/0x63700019
Activate outbound key with SPI=0x1c4cafaa for inbound key with SPI=0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
90 09:46:00.947 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205277
91 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
92 09:46:01.529 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
93 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205277, seq# expected = 107205277
94 09:46:11.952 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
95 09:46:11.952 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205278
96 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
97 09:46:11.979 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
98 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205278, seq# expected = 107205278
Any help would be appreciated, thanks!I made the change that you requested by moving the VPN pool to the 192.168.3.0 network. Unfortunately, now traffic isn't flowing to the inside network at all. I was going to make a specific route as you suggested, but as far as I can see the routes are already being created correctly on the VPN client's end.
Here is the route print off of the computer behind the (test) client:
===========================================================================
Interface List
21...00 05 9a 3c 78 00 ......Cisco Systems VPN Adapter for 64-bit Windows
10...00 15 5d 01 02 01 ......Microsoft Hyper-V Network Adapter
15...00 15 5d 01 02 02 ......Microsoft Hyper-V Network Adapter #2
1...........................Software Loopback Interface 1
13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter
16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2
23...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
69.61.228.178 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 On-link 96.11.251.149 261
96.11.251.149 255.255.255.255 On-link 96.11.251.149 261
96.11.251.255 255.255.255.255 On-link 96.11.251.149 261
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.1.0 255.255.255.0 On-link 192.168.1.3 261
192.168.1.3 255.255.255.255 On-link 192.168.1.3 261
192.168.1.255 255.255.255.255 On-link 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.3.1 192.168.3.70 100
192.168.3.0 255.255.255.0 On-link 192.168.3.70 261
192.168.3.70 255.255.255.255 On-link 192.168.3.70 261
192.168.3.255 255.255.255.255 On-link 192.168.3.70 261
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.1.3 261
224.0.0.0 240.0.0.0 On-link 96.11.251.149 261
224.0.0.0 240.0.0.0 On-link 192.168.3.70 261
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.1.3 261
255.255.255.255 255.255.255.255 On-link 96.11.251.149 261
255.255.255.255 255.255.255.255 On-link 192.168.3.70 261
===========================================================================
Persistent Routes:
Network Address Netmask Gateway Address Metric
0.0.0.0 0.0.0.0 96.11.251.1 Default
===========================================================================
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
14 1020 ::/0 2002:c058:6301::c058:6301
14 1020 ::/0 2002:c058:6301::1
1 306 ::1/128 On-link
14 1005 2002::/16 On-link
14 261 2002:600b:fb95::600b:fb95/128
On-link
15 261 fe80::/64 On-link
10 261 fe80::/64 On-link
21 261 fe80::/64 On-link
10 261 fe80::64ae:bae7:3dc0:c8c4/128
On-link
21 261 fe80::e9f7:e24:3147:bd/128
On-link
15 261 fe80::f116:2dfd:1771:125a/128
On-link
1 306 ff00::/8 On-link
15 261 ff00::/8 On-link
10 261 ff00::/8 On-link
21 261 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
And here is the updated running config in case you need it:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
access-list outside_specific_blocks extended deny ip host 121.168.66.35 any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
ip local pool VPN_Split_Pool 192.168.3.70-192.168.3.80 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh 96.11.251.186 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Split_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Split_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Split_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:9e8466cd318c0bd35bc660fa65ba7a03
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Thanks again for your help,
Matthew
Maybe you are looking for
-
How to find serial number without using macbook?
What can be used to find serial number of my macbook outside of using my macbook? My computer was stolen and I do not have the box nor do I have it registered in iCloud, I know that iTunes holds my computer as an authorized user for my ID so I am sur
-
Number field not displaying the decimal part
Hi, In a VO I've an attribute which is of type Number. I've set the precision & scale for the attribute as 16,4 Even though the value in the database is having decimal part still in the UI it is just displaying the integer part.
-
Federating the Business explorer role
Recently we have successfully federated some reports for some business users. Now another business group is interested in federating the Business explorer role. They would like to take advantage of the BexWebanayzer iview and a few of its features.
-
Is there any way we can copy already entered data and paste into other tab or field. The system is not allowing me select the data to copy. Thanks and regards Madhu
-
I ran an Apple Hardware Test because my memory and display seems to not be working properly. Any help would be appreciated, thanks. About my Mac: MacBook Pro 15' Early 2011 Version OS X Version 10.9.4 Processor: 2GHz Intel Core i7 Memory: 8GB 133 MHz