Trying to open and install an old cd program but when I click to open it said file.osx can't be open because the PowerPC applications are no longer supported. Any suggestions thx
thx
That's what it means. The program cannot be run on your Mac. It is old PowerPC code. You need to get a version that will run on an Intel-based Mac.
Similar Messages
-
i upgraded to lion when it first came out but today i tried to open my photoshop cs2 and its telling me the powerpc applications are no longer supported is there any fix out there for this
Lion is Not compatible with PPC (Power PC) based software, such as your older version of PhotoShop. Your choices are you can either upgrade to the newer version of PhotoShop, or you can backup your data and apps, erase your harddrive and reinstall Snow Leopard.
Hope this helps -
I have installed Lion and Microsoft Office 2011. I want to uninstall Office 2004, but of course I cannot run the application to uninstall, because I get the "PowerPC applications are no longer supported" message. Suggestions?
Go to this microsoft site http://support.microsoft.com/kb/312172 and/or this microsoft site http://support.microsoft.com/kb/2398768. I would suggest removing both to start with a clean slate. I had some problems with installing Office for Mac 2011 over 2008 and found out that by completely removing both and starting from a clean slate provided the best solution. Kappy is correct but some sniglets do get left behind. Hope this helps. Cheers.
-
I am getting the PowerPC applications are no longer supported error, so I downloaded Libreoffice and can not find it on my hard drive anywhere. It did say it would install to Applications, but it's not there. How do I find it and can I put it in my dock?
In Safari's preferences:
Look in the folder displayed where you see the arrow. The actual Downloads folder is found in your Home (user) folder. -
I face a problem with my macbook air or i think it's from the lion OS cause i didn't happen with snow leopard OS the massage says ( you can't open the application ....... because powerPC applications are no longer supported). any advice ??
Mac OS X Lion has dropped support for Rosetta, the feature that allowed you to run PowerPC apps on previous OS X systems. Check if you can find a newer version of the app you are trying to run that supports Intel processors.
What application are you trying to run? Maybe I can help you find a version that runs on Lion. -
Safari and the App store icons are both deactivated. I also cannot a software update check, as it gives the 'PowerPC applications are no longer supported error'
Very frustrating, cannot do anything with this laptop now. Any help is greatly appreciated.If you don't already have a current backup, back up all data. There are ways to back up a computer that isn't fully functional. Ask if you need guidance. You can skip this step if you don't care about the data that hasn't been backed up.
Reinstall the OS.* Your data should be unaffected unless something goes wrong. If the system was upgraded from an older version of OS X, you may need the Apple ID and password you used.
If you use FileVault 2, then before running the Installer you must launch Disk Utility and select the icon of the FileVault startup volume ("Macintosh HD," unless you gave it a different name.) It will be nested below another icon with the same name. Click the Unlock button in the toolbar and enter your login password when prompted. Then quit Disk Utility to be returned to the main Recovery screen.
If you installed the Java runtime distributed by Apple and still need it, you'll have to reinstall it. The same goes for Xcode. All other data will be preserved.
*The linked support article refers to OS X 10.9 ("Mavericks"), but the procedure is the same for OS X 10.7 ("Lion") and later. -
What does "You can't open the application "Setup QuarkXPress6.1" because power PC applications are no longer supported" mean? I am trying to install an old version of Quark on my 2010 Macbook pro.
jennyba wrote:
What does "You can't open the application "Setup QuarkXPress6.1" because power PC applications are no longer supported" mean? I am trying to install an old version of Quark on my 2010 Macbook pro.
As has been mentioned, the software in Mac OS X that supported the running of PPC applications rather than current Intel applications on Intel computers such as your MBP was last seen in Snow Leopard. However, since I believe your MBP originally came with Snow Leopard, you may be able to boot from the DVD's that came with the computer and install it on an external HD and try to install Quark on that.
I think a better solution would be to buy Snow Leopard Server from Apple by phone (800-692-7753 and be specific about wanting part # MC588Z/A), installing it as a virtual machine in software like VMware Fusion, and then installing Quark 6 in that. You'll still need a license number to authorize the Quark installation. -
I installed a new hard drive and trying to reinstall FCP2 and on the install disc i get the following message - "You can't open the application FC Studio.mpkg because power PC applications are no longer supported"
Because you are running lion.. FCS 6 is a Power PC app and Lion doesn't support Power PC anymore.. So you can't install it.. Three options..
1. Revert back to Snow Leopard.
2. Purchase FCP X...
if you can't stand FCP X
3. Call apple directly, 1800-MYAPPLE and ask to purachse FCS 3 for $999... (its FCP 7)
I just got FCS 3 today through apple phone sales.. -
i purchased dvd studio pro and im trying to install it but when i go to click continue it gives me this "you cant open the application gestalt tool becasue powerpc applications are no longer supported" what does that mean and how can i fix this ?
I note this information from Wikipedia: "DVD Studio Pro was a high-end software tool published by Apple Inc. to allow users to create DVD masters to be sent out for replication at production houses. Its tight integration with other Apple applications allows users to take Final Cut Pro and Motion projects and render them into the DVD format without encoding to intermediary formats. This streamlines the production workflow and reduces overhead."
If that is your intent, finding a substitute program that will run on your Mac may not be as efficient. Others can advise you on alternatives, or you can post a new thread specifically with that question.
BTW: what Mac and what version of OS X?
If it is important to you to continue to use DVD Studio Pro, consider the option of installing Snow Leopard (with Rosetta) into Parallels on your Mac:
[click on image to enlarge]
Full Snow Leopard installation instructions are here. -
I am trying to install Final cut pro 5 studio V1.0.1 (2005) on OS X lion. I get a message "You can't open the application final cut studio.mpkg because power pc application are no longer supported. My computer is New. Is their a link I can go to get tech support?
You won't find any help at tech support ... other than telling you the facts: Intel processor Macs require FCP 5.1 or higher. FCP 5.0 and earlier were written for PowerPC processor Macs, long before Apple switched to using Intel processors.
And then there's the issue of the OS. OS 7 will allow FCP 7 (and sometimes even FCP 6) to work OK, but versions earlier than that have spotty operation on Lion.
Here's a brief history of full FCP versions and recommended OS compatibility:
* = requires PPC ** = works with both PPC and Intel *** = require Intel
FCP 1.0* OS 9
FCP 2.0* OS 9
FCP 3.0* OS 9, OS 10.1, OS 10.2
FCP 4.0* OS 10.2, 10.3
FCP 4.5* OS 10.3
FCP 5.0* OS 10.3 (OS 10.4?)
FCP 5.1** OS 10.4, 10.5
FCP 6.0** OS 10.4, 10.5, 10.6 (OS 10.7?)
FCP 7.0*** OS 10.6, OS 10.7
FCP-X*** OS 10.6, OS 10.7
Essentially, you have a newer Intel processor Mac with a new OS and very old, incompatible software. You might be able to find a used version of Final Cut Studio 3 on sites like ebay or craigslist as it is no longer offered by Apple as an upgrade.
Alternatively, you could purchase and download FCP-X, but it is an entirely different application, sharing virtually nothing with previous versions of FCP.
-DH -
Tried to install a new game that I bought (Xiii) for my MBP. All system req have been met and exceeded, however when trying to install it I get an error message saying "You can’t open the application “XIII Install” because PowerPC applications are no longer supported."
I have since read online that the operating software Yosemite has got rid of PowerPC applications, meaning I can't install my new game.
Is there anything simple that I can do to get this game to work. I'll be gutted if not as I have opened the game therefore the shop will not give a full refund, I'm sure .
Regards
SimonA lot longer ago than that. PowerPC apps haven't been supported since Lion, 10.7.x.
You may have just purchased the game, but the developers obviously haven't kept up to date with the requirements for newer versions of the Mac OS.
You have three options, depending on how old your Mac is.
1) If it were ever able to boot directly to Snow Leopard, you could create a separate partition and install SL onto that partition. Make sure to turn on the option during the installation to install Rosetta. That is OS X's PPC emulator.
2) If your Mac is too new to install Snow Leopard, then you can purchase and install Snow Leopard Server within a VM, such as Parallels, VirtualBox, or Vmware.
3) Use a separate older Mac for running outdated software. -
So I've been trying to open some Microsoft Word Documents and it says it can't be opened because PowerPC applications are no longer supported. What do I do about this?
Workarounds:
1. Restore the OS X that you formerly used to run Word 2004;
2. Partition your hard drive or attach an external hard drive and install Snow Leopard (and Rosetta) so that you can "dual-boot" into Microsoft Word 2004;
3. Upgrade to Word 2011 or use an alternative program; or
4. The solution I use: Install Snow Leopard (and Rosetta) into Parallels 7 or 8:
[click on image to enlarge]
Full Snow Leopard installation instructions here:
http://forums.macrumors.com/showthread.php?t=1365439 -
I am trying to install print controller and printer -but get this error message when trying to use the installer:
You can’t open the application “OSX installer” because PowerPC applications are no longer supported.
I also have a macbook pro running the same version OS and it installed fine there - I can't find the difference; but, NEED to print from my IMac.
Any help and/or suggestions would be greatly appreciated
Thanks!I'm guessing you've tried Fiery's website for updated drivers? I wonder whether Lion drivers would work? Anything of use here:
http://fieryforums.efi.com/showthread.php/2824-OS-10.7-compatible-drivers-availa ble?s=c8afc71d2746a67970bb42d50538898c -
i am trying to restore my mac osx 10.7.4 from an ext lacie harddrive and getting message "u can't open the application lacie backup support because power pc application are no longer supported"
Use any number of free alternatives to your nearly decade old version of MS Office.
Consider
LibreOffice (donation-supported)
NeoOffice (free)
OpenOffice (free)
In addition to the above I also recommend Apple's Pages ($19.99). I use OpenOffice and Pages and have been completely Microsoft - free for years. Life is better without Microsoft. -
I installed Lion 10.7.4. Went to use Photoshop Cs and got a popup window. You can't open the application Adobe Photoshop CS because PowerPC applications are no longer supported. Is there a way of getting this to work or do I have to get newest version of all of my Power PC apps?
Welcome to Apple Communities
PowerPC applications are unsupported in newer versions. You can upgrade Photoshop or you can install Snow Leopard in a partition.
1. Open Disk Utility (Applications > Utilities) and select your drive
2. Go to Partitions tab, press + button, create a new partition and press Apply
3. Insert the Snow Leopard install DVD and reboot pressing C key
4. Install it in the new partition
5. If you want to change boot, go to System Preferences > Startup Disk and select 10.7
Maybe you are looking for
-
hi All, URGENT REQUIREMENT PLEASE HELP ME I have a table of type DefaultTableModel .The table has rowheaders and columnheaders which are dynamically generated from the DB. On action i want to add/remove a rowheader which should be update the rowheade
-
After upgrading to OS X Lion Aperture 3.1.3 runs very slowly and crashes
After upgrading to OS X Lion Aperture 3.1.3 runs very slowly and crashes regularly when editing and/or exporting images. Prior to the upgrade these problems did not exist - has anyone else encountered this behavior and found a resolution? My iMac ha
-
Change Publisher name in AppStore
Apple, I submitted my Application in iTunes Connect and it got approved. In AppStore and iTunes my App is displaying as AppName and underneath Publisher name and category . I would like to remove Publisher name and display as Appname and in
-
Dear Experts, I am implementing GRC AC RAR 5.3, i need to connect my grc dev system to two back end systems(ecc6 dev, ecc qa) how i need to create connectors. should i use local system or do i need to create connecters seperately.. which one is the
-
The little "x" on my safari tabs isn't appearing anymore, what is that?
to close its tabs i gotta click with the right button and choose ''close tab'', it *****!! it was much better with the little ''x'' does anyone know what should i do to have it back?