1841 with HWIC-AP multiple SSIDs to different subnets

Hi experts,
Please point me toward the right direction, how do I do this setup? Please give me some example? Is this different L3 BVIs along with sub interfaces on dot11radio interface assigned to different bridge-groups?
Thanks a lot.
Regards,
GP

Hi again,
I have managed to make it work. Just in case someone needs the same configuration within a singe Cisco1841 router.
Thanks.
dot11 ssid cisco
vlan 10
authentication open
authentication key-management wpa
wpa-psk ascii 7 05080F1C22434D000A0618
dot11 ssid cisco-guest
vlan 100
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 1511021F0725282D3B303A
bridge irb
interface Dot11Radio0/0/0
no ip address
encryption mode ciphers aes-ccm
encryption vlan 10 mode ciphers aes-ccm
encryption vlan 100 mode ciphers aes-ccm
ssid cisco
ssid cisco-guest
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root access-point
interface Dot11Radio0/0/0.10
encapsulation dot1Q 10
no cdp enable
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
interface Dot11Radio0/0/0.100
encapsulation dot1Q 100
no cdp enable
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface BVI10
ip address 10.0.0.1 255.255.255.0
interface BVI100
ip address 10.1.1.1 255.255.255.0
bridge 10 route ip
bridge 100 route ip

Similar Messages

AP groups with same vlans , same ssid but different subnet.

Hi Members,
I have a Cisco Flex 7500 in my datacenter and I need to connect 100 sites , each site with 2-3 APs , each side has its own network and is independent of other sites , the site only need to comunity locally and do not need to access any centralized applications.
I am trying to achieve this by Creating 100 different AP groups and assiging 2-3 AP in each groups for each branch, I will achieve WAN failover resiliency by creating flexconnect groug , the issue I am facing are as below .
1.Since all the sites has same setup , the AP and clients on all sites are in vlan 2 , so when I try to create 2 or more AP group with same vlan, it restricts me of doing so , I cannot create diffrent AP groups mapped to same Vlan .
2.If I keep the APs and Clients in the same subnet , I dont think it should be a problem , but I need your second opinion.
to give you an even better picture , look at the topology enclosed , and my question is if both STAFF and STUDENT APs are in same vlan but in 2 different broadcast domain , how would I create the AP groups.
Thank you

Thanks for the reply Jenn , here is my situation.
I have 2 sites lets day , site A in virginia , site B in Maryland.
SiteA - 10.1.1.0/24 - vlan 2
           10.1.2.0/24 - vlan 3
           10.1.3.0/30 - WAN to central site where controller sits.
SiteB - 10.2.1.0/24 - vlan 2
           10.2.2.0/24 - vlan 3
           10.2.3.0/30 - WAN to central site where controller sits.
both the sites will have a single ssid "XYZ" and will switch locally only.
howin my understanding the way I will deploy this is as below
1.I will create WLAN with ssid "XYZ".
2.I will create 2 AP groups lets say "Site-A" and "Site-B"
3.I will map the APs in site A to AP group "Site-A" and APs in Site B to "Site-B"
4.I will create 2 dynamic interfaces one for each AP group , now this is where I am facing problem , when I am creating dynamin interfaces , I need to specify the subnet and vlans when creating dynamic interfaces , since the vlans used is same on both sites , its not letting me create 2 interfaces with same vlan id.
in my understanding HREAP is only majorly used for WAN failover and local authentication so I am not concerned about that right not , my prime work is to udnerstand the AP group and working.
if you still need print shot let me know I will have to go at site.
also validate if my thinking is right on the 4 steps I have mentioned above , I am new to wireless and whatever I have learned I have learned in last 10 days .
Appreciate your help.
Thank you

Multiple VIPs in Different Subnets

Is there any way to setup the CSS with VIPs in different subnets. If we were using an inline configuration, I don't see how this would be possible.
Let's assume three subnets A, B, and C. We would like to have a VIP in subnet A pointing to all the web servers in subnet A. Same for subnets B and C.
I guess we could configure a trunk port with a CIRCUIT interface in each of the subnets A, B, and C. This would allow clients to route to the VIP in each subnet. My concern is the return traffic. With only one default route in the CSS, all return traffic would traverse one CIRCUIT interface. Am I correct, or am I misunderstanding something?
Thanks!
Tom

I believe you are correct. We have practically the same scenario working here. I have a /29 allocated to the front-end of the CSS and the upstream HSRP routers (call that vlan 10). Then I have multiple subnets for backend servers behind the CSS setup as an 802.1q trunk vlans (call them VLAN 100, 101, 102, etc). I route for those subnets belonging to VLANs 101, 102, etc on the upstream routers to point to the VRRP address of the CSS (the VRRP address of the CSS in VLAN 10). I also route whatever IP used as a virtual to the CSS VRRP address as well. So my upstream routes will have routes to the VIPs and the backend VLANs all pointing to the CSS's VRRP address.
Casey

Using DHCP with a cFP-20XX across a different subnet

I have a cFP-2010 that will work great when set up with a static IP or DHCP as long as it is on the same subnet. If I set it for DHCP then move it to a different subnet, MAX can no longer find it. Do I have to use a static IP when going across subnets, or is there something I'm missing?
Thanks,
Steve

Selmore,
Not 100% sure this will work for FieldPoint controllers, but for some
other NI controllers (e.g. CompactRIO) if you give a name to the
controller in MAX and set it to use DHCP, then when its IP address is
assigned by the DHCP server its name is registered as a DNS name. That
means you can use that name to communicate to it from a different
subnet. By using ping commands you should be able to demonstrate if
this works for FieldPoint or not; I believe it should.
Hope my answer is clear enough and helps.
JMota

PXE boot issue with DHCP and SCCM server on different subnets

I'm working with a client on the operating system deployment module of SCCM.
Their network configuration currently has a single large subnet for client
computers with a DHCP server on the same subnet. The SCCM subnet is
configured on a seperate subnet with no DHCP server on the subnet. We want to
configure client computers to be able to boot using the PXE client to deploy
OS images to the machines but can not get PXE-boot to work correctly.
Also, the client does not want to make changes to their network
infrastructure routers or switches to remedy this problem. Are there settings
on the DHCP or SCCM servers we can implement to make this work? If so, what
needs to be installed or configured on each server. We currently already have
WDS installed on the SCCM server and the SCCM server is configured as a PXE
Service Point within SCCM. Both WDS and the PXE Service Point seem to be working fine.
Any help would be appreciated.
Thanks,
Gary

I am Brazilian,
sorry for wrong english
My DHCP is on linux,
in my own structure VLANS
The system center is on the network
10.0.4.0/24
The machines on the network 10.0.5.0/24
The problem is that the machines that
are not on the same network system center
can not boot
I tried configuring / etc/dhcp3/dhcpd.conf
follows
option vendor-class-identifier "PXEClient";
option bootfile-name "\
\ SMSBOOT \ \ x86 \
\ wdsnbp.com";
option tftp-server-name
"10.0.4.101"; ---->
IP server
But it did not work, anyone know
how to configure?

WAP4410N and multiple SSIDs on different VLANs using RADIUS

I am trying to setup the above environment. When I connect on my guest network it does not give me an IP address from my guest network DHCP scope that is configured on my CISCO router.
Does anyone have any idea how to set this up???
Any help would be appreciated...

It is most likely (I'm not certain from the description) that
the 'sub-buttons' are a 'child' MC of the main button? if so, the
'on' handler for the 'main' button will override any handlers
attached to 'child' buttons within it. the only solution is to use
a hitTest method for either the 'parent' button or the 'child'
buttons, OR separate the two MCs and use the 'main' button to bring
a MC of the 'sub' buttons to the Stage.

Multiple SSID with different Login Web authority pages

Our current setup is one Anchor control and then several WLC’s, I want to know if I can have multiple SSID and use different Web Auth pages form them, so I can have a SSID that requires a password to Authentication access and another SSID that requires pass through Authentication but they would have different web authentication pages and go to different pages once Authenticated.
Is this possible to ?

Hi,
If you are running WLC software 4.2 and above then u can do this on per WLAN basis.. here is the link which tells on how to do it..
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008067489f.shtml#A1
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra

HT201210 my iphone 3gs keeps showing the screen with the connect to itunes display, and I've restored it multiple times on different computers, but everytime it finishes restoring, it shows the display again and the computer says it needs to be restored.

my iphone 3gs keeps showing the screen with the connect to itunes display, and I've restored it multiple times on different computers, but everytime it finishes restoring, it shows the display again and the computer says it needs to be restored. can anybody help me with this?

it was saying error code 1, i tried the things it said but none of it worked. now it is not showing an error code at all, it just keeps saying it needs to be restored.

Using multiple SSID with AP 1100 (standalone mode).

Hi, need to configure 2 SSID on the same 1100 AP: open authentication and WPA2. It's possible to configure these 2 SSID without configuring VLAN's ?
On CCO I've read the following:
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a008009483e.shtml
Q. How many service set identifiers (SSIDs) can you have per VLAN?
A. You can have only one SSID per VLAN. The use of multiple SSIDs over a single VLAN is not supported with Aironet APs.
It's also true with the latest IOS release ?

Hi Roberto,
Hopefully the attached docs will answer your question:
Cisco Aironet 1100 Series
Using VLANs with Cisco Aironet Wireless Equipment
Deprecated versions of Cisco Aironet software permit binding multiple SSIDs to one VLAN. Current versions do not.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#
Cisco IOS Software Configuration Guide for Cisco Aironet Access Points, 12.2(15)JA
Configuring Multiple SSIDs
vlan vlan-id
(Optional) Assign the SSID to a VLAN on your network. Client devices that associate using the SSID are grouped into this VLAN. You can assign only one SSID to a VLAN.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a00802085c4.html
Hope this helps!
Rob
Please remember to rate helpful posts.......

WAP200 and .1x/radius authentication with multiple SSIDs

Apparently it's not possible to define more than a single radius server when using multiple SSIDs with WAP200. Unfortunately WAP200 doesn't add the name of the SSID as a radius attribute, so it's not possible to make distinction whether the user is trying to log in to SSID A or B. Does anyone have any ideas or workarounds for this limitation? Of course the best solution would be if Cisco/Linksys fixed the firmware so that the SSID of the logging in user would be sent to the radius server as an extra attribute or appended to the client mac address.

Security option for an SSID can be unique and can be configured when you configure a SSID or under VLAN . Note that each vlan is uniquely mapped to induvidual SSID.

Authentication with Multiple SSIDs AP521G, using Autonomous

I have an AP521G access point that I am trying to setup authentication for multiple SSIDs. One SSID is for domain users with WPA/TKIP authentication to a radius server and the other SSID is for guest to have access to Internet with no authentication. Is there a way to setup both SSIDs on the AP for this configuration?

Security option for an SSID can be unique and can be configured when you configure a SSID or under VLAN . Note that each vlan is uniquely mapped to induvidual SSID.

Multiple SSIDS with VLAN ACL seperation

Hi,
I have bought a 887W and I'm new to wireless on a router, I need advice about seperating multiple SSIDs with access list.
I have configured 2 SSIDs one for 'trusted' clients and one for 'guest' clients. I want to prevent the 'guest' SSID obtaining access to the other vlan/SSID using an ACL.
Each SSID is associated with a BVI, the BVI has the IP address, then it's linked to a seperated VLAN interface, then each VLAN.
Thanks if you can help...
Dave

Solved my issue, I simply attached the ACLs to the BVI interfaces. Fairly obvious, but I read a Cisco webpage that said this could not be done, although this may have been a temporary bug that has been fixed.

Wireless Network Management with Multiple SSIDs in one Wireless Profile

Could anybody explain me about how Multiple SSIDs in one Wireless Network Name (Network Profile) ? Configuration will be pushed to Windows 7 Pro from Wins Server 2008 R2.
Objective: Multiple office locations will have different SSIDs and when the laptop user travels one location to another, he/she could connect to wireless networks at any offices without any configuration change but utilizing "Automatically use my Windows
logon name and password (and domain if any.)" setting in EAP MSCHAPv2 properties.
Network Name: Enterprise
SSIDS: SFO-WIFI, LAX-WIFI,CHI-WIFI,NYC-WIFI,
Network Type:Access Point
Security Type: WPA2-Enterprise
Encryption Type: AES
Network Authentication Method: Microsoft:Protect EAP(PEAP)
My question is: (1) Will Windows try all the SSIDs in order to get connected to the Wireless Network at the office? (Let's say, user is in NYC, but will Windows try to find SFO-WIFI SSID first, wait until time out, retry?, and moves on to LAS-WIFI SSID,
wait until time out, retry?, and moves on to CHI-WIFI and finally tries NYC-WIFI SSID and found the SSID in the beacon from Access Point and authenticates through RADIUS?
(2) If the answer is YES, what is the waiting time/timeout setting for one SSID before moves on to another?
(3) If the answer is NO, what is the process to get user connected to NYC-WIFI SSID when he/she is in NYC office within the range of that SSID?

Hello Ninjago_2224,
About the multiple office location have different SSIDs, does the location A has the signal used in
location D?
Please go to Control Panel\Network and Internet\Network and Sharing Center
, and then click Manage wireless networks.
The windows will try to connect to these networks in the order listed.
Please check if the four SSID pushed by Windows Server 2008 is listed as mentioned above.
If the location A have the location D SSID and the location D SSID has higher priority, the Windows will connect to
location D SSID.
So about the question 1, the Windows will try the SSID in order.
About the question 2, I can’t find the accurate time that test one SSID and move to another. But based on my test, it is very fast.
For more information, please take a look at the following article.
http://www.howtogeek.com/howto/27067/change-wireless-network-priority-to-make-windows-7-choose-the-right-network-first/
Please note: Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

BEx Broadcaster - Using a Workbook with multiple queries on different tabs

Hi,
I was wondering if any has used Bex Broadcaster to broadcast a workbook that contains multiple queries on different tabs in the workbook. I believe someone has mentioned that this was an issue in the past and I was wondering if this now a possibility with Bex Broadcaster
If you were able to do this successfully, please let me know.
Thanks

Hello
Of course it is possible.
But, if you want to broadcast a workbook, you have to use a Precalculation Server.
Without precalculation server, workbooks cannot be precalculated and broadcasted.
More details, please check the note below:
1461398 BW 7.X(7.20) Precalculation - General Info. & Limitations
Best regards,
Edward John

I am making multiple DVD's of roughly 50 hours of footage on DVD Studio pro with 4 separate menus for 4 different 'parts' or series if you will. 50 hours - 20 episodes - 4 parts of 5 episodes each. What are my options in terms of burning these parts on to

I am making multiple DVD's of roughly 50 hours of footage on DVD Studio pro with 4 separate menus for 4 different 'parts' or series if you will. 50 hours - 20 episodes - 4 parts of 5 episodes each. What are my options in terms of burning these parts on to separate DVD's, what is the process, what size DVD RW should I buy, what bitrate should I use, and what quality I should expect for the burn. Any advice or insight is welcome.

>>What are my options in terms of burning these parts on to separate DVD's<<
20 episodes totaling 50 hours equals about 2.5 hours per episode assuming all episodes have the same duration. Fitting 2.5 hours onto one single layer DVD would require a low bit rate which means quality wouldn't be anywhere near best, but that's a judgement call you'll have to make based on several factors. For example; if there is not much motion in the video (talking heads, etc), you can get by with a lower bit rate and may not notice any quality difference.
>>what is the process>>
The process is essentially the same as it is when authoring a regular DVD with 2 hours or less of content. However, with as many discs as you'd need to complete this "set," you'll need to create a separate DVD Studio Project for each disc. Basically, you'd use one of Compressor's DVD Presets (or customize a preset) to create an MPEG--2 video file (.m2v) and a Dolby Digital audio file (.AC3). Import both of those assets into your DVD Studio Pro project for authoring and burning.
If you want to keep one episode per disc, DVD Studio Pro does have a 150 minute preset or you could use dual-layer discs with a higher bit rate for better quality. Again; your call.
>>what size DVD RW should I buy<<
Size? 12cm. Capacity? Single layer, single sided DVD discs (DVD-5) have a rated capacity of 4.7Gb (4.37Gb actual), including menus. If you use single layer discs and want to keep the quality reasonably good, you'd need at least 50 discs to complete this "set" with each disc holding roughly 2 hours of footage if you keep the menu on each disc simple. Or, you could use dual-layer discs (DVD-9) which have a capacity of about 7.95Gb - almost doubling the recordable capacity. There are also dual-sided, dual-layer discs available (DVD-18) but they are relatively expensive and have to be manually turned over to continue playback ... but they do have roughly 15.9Gb capacity.
>>what bitrate should I use, and what quality I should expect for the burn<<
Exactly; the quality is dependent on the bit rate chosen, as well as the quality of the compression. Using compression markers where needed can greatly increase the quality of playback but will most likely increase the file size of the compressed video. For the best quality, keeping the bit rate as high as possible allowed under the DVD specification will yield the best quality but some DVD players may choke if the bit rate is too high. For best quality I typically aim for a bit rate around 7.6 to 8.0Mbps but that will only allow about one hour of footage.
Naturally, if you decrease the bit rate, you can fit more footage onto the disc but quality will be sacraficed.   Here's a chart approximating DVD bit rates and durations for single layer discs (does not include space for menus):
3.5Mbps - 120 minutes
5.0Mbps -   95 minutes
6.0Mbps -   82 minutes
7.6Mbps -   65 minutes
8.0Mbps -   60 minutes
-DH

1841 with HWIC-AP multiple SSIDs to different subnets

Similar Messages

Maybe you are looking for