3D graph plot properties - cannot be changed

Hi all,
I still cannot change the plot properties of the 3D graph. I open the Plot Properties tab up and it gets stuck on the first page.
This means that I cannot release any VIs which use the 3D graph - a big problem.
Has anyone else experience this? What do you suggest to fix it.
Thanks,
Battler.

I have experienced exactly the same behavior (can not change 3D graph plot properties) with 3D plots (scatter and surface) in LabVIEW 2011. The 3D plot properties page works correctly at first but then fails to switch pages after larger data sets have been loaded to the graph. For example, my scatter graph contains 13 plots, each with 320 points of data. Once the page "gets stuck" it is stuck for all 3D graphs until the offending graph is deleted and re-created. To reproduce this issue create at least one 3D plot with a large number of plots in it.
On a related note, if there was a programmatic method for deleting plots from a 3D graph then it's possible that this issue could be worked around.

Similar Messages

Problems with XY Graph "forgetting" plot properties

I am having trouble with an XT Graph in my loop.
The graph has 10 plots which at any time can have anything from 0 to ~1000 points, often some plots will have significantly less ploints than others. There is a user selectable option to display all points or just the most recent set.
My problem is that I want the graph to reflect the input data by plotting a single point at the time of an update, so I have a string of points rather than a line.
When I right click the graph and go into properties, I change the point style to solid circle and turn off line interpolation. I then click save these values as default, and save the vi.
However, once I run the vi, the graph always reverts plots 1 to 9 (not plot 0, this stays as I want it) to have no points displayed and line interpolation on.
Has anyone had this problem before? Ho did you fix it?
I know it can be fixed, as I had this probelm a few months ago on a similar vi and after weeks of struggle I solved it, however I just cannot remember how I did it.
Thank you for any help, at the moment I can't post any code. Note that the data the graph shows is all perfectly fine, just the plot properties are being forgotten.
Solved!
Go to Solution.

HI DarraghCorrigan,
In relation to the problem expressed in your initial post:
"once I run the vi, the graph always reverts plots 1 to 9 (not plot 0, this stays as I want it) to have no points displayed and line interpolation on"
This is due to a bug in the LabVIEW software whereby any changes that are made to the plot properties (e.g. to change the colour of a plot) will not be retained, except in plot 0 which is unaffected. Our R&D department are currently investigating this problem so that it can be fixed in future version of the software. The recommended workaround for this problem is to pragmatically set the plot settings at the beginning of the code using property nodes.
As I understand it, this is not the main problem that you are experiencing. If you set up the properties for a plot (using some of the described property nodes) which is subsequently removed or rewritten on an XY Graph, my understanding is that there is no way that LabVIEW can remember and retain these properties.
As you rightly suggested, one way of conveniently overcoming this problem would be to set default plot properties so that when you remove/rewrite a plot and then add it again, it will always default to those properties. Unfortunately, it is not currently possible to do this though it has been recommended as a product suggestion so it is a feature that is under consideration for implementation in future releases of LabVIEW.
I think the issue you need to be addressing is the fact that you are at some point resetting the graph by sending an empty array to it such that all of your properties are lost. If you can find and remove this section in your code, you should be able to overcome your problem.
I hope this helps.
Best Regards,
Christian Hartshorne
NIUK

Changing Graph Plot Legend

I have no problem changing a normal graphs plot legend with a property node, but I'm trying to display three different sets of data on one graph. I tried doing it using a plot reference with the Plot Legend and using Caption Text. They should be settable when the VI is running, but the way I was trying to do it I got a reference error (1055 Reference Invalid). Setting either the Plot Legend or Caption Text would be acceptable if I could just figure it out.
I'm trying to display 32 spectrums, but only use 8 graphs and have the name of the particular channel change. Doing this without doing an FFT the channel name gets brought into the graph, but when I use the Power Spectrum VI I don't have the Spectrum Info wired into anything. So, I'm bringing my original channel name array over and trying to do an iteration to pick the correct plot reference and channel name.
I've extracted only the part of my code for this question, so hopefully it is easy to look at what I'm doing.
The first VI and SubVI are functional. The second SubVI is where I was attempting to change the Caption Text. I've tried other things too, but I just wanted to show one way I was attempting to do it.
Solved!
Go to Solution.
Attachments:
Part of Analyzer - Displaying Graph Legend.vi ‏1432 KB
Calc Channel Indices 1_35.vi ‏27 KB

I don't have the SV add on so I can't check out your main program. I looked at your sub vi and you're doing more code than you need to. Take a look at my example, I've put your 8 graphs into a cluster then used an array of references along with arrays for your chanel indecies. Maybe it can give you some ideas for your program.
Attachments:
Calc Channel Indices 1_35 mod.vi ‏766 KB

Change order of wpf graph plots

I'm trying to solve following issue. Let's say I'm sampling data once per second and showing it on the graph. I want to show history of the data, say last 20 plots using the same color with fading. What I do now:
- create 21 plots, say Plots[0]..Plots[20]
- at meas 1, set Data[0] = data
- set Plots[0] opacity to 1
- at meas 2, set Data[1] = data
- set Plots[1] opacity to 1, Plots[0] opacity to 0.5
- at meas 3, set Data[2] = data
- set Plots[2] opacity to 1, Plots[1] opacity to 0.6, Plots[0] opacity to 0.3
- at meas 21, set Data[20] = data
- set opacity to 0.1..1
// we're fine as of now, here comes the tricky part
- at meas 22 I need to remove the data of meas 0 (stored at Data[0]) and replace it with the new data
- so I set Data[0] = data
- set Plots[0] opacity to 1 (it's the newest result)
- set other plots opacity 0.1..0.9
// and here is the problem: Plots[0] is now at the bottom of the plot stack and is covered by 20 other plots, thus is barely visible
so I somehow need to move Plots[0] to the top of the stack
I've tried removing Plot and Data of the farthest plot and adding creating plot with the most recent data, but it leads to incorrect indices (Plot.Index grows all the time, but Data array stays the same)
Another option would be to fix plots order and opacity in advance, and change data for all plots all the time. But I assume this would be very slow (think of 20-50 copies of the plot with say 1000 points).
So, any bright ideas here?

Idea 1) Pre-allocate all of the fade plots, use BeginInit/EndInit when updating the Data collection, and always apply the newest data to the last plot. In pseudo-code:
    // initial setup
    for( opacity = 0..1 )
        var renderer = new Renderer( opacity )
        graph.Plots.Add( new Plot { Renderer = renderer } )
    // on data update
    graph.BeginInit()
    for( i = 1..graph.Data.Count )
        graph.Data[i - 1] = graph.Data[i] /* shift old data down */
    graph.Data[20] = /* assign new data to the last plot */
    graph.EndInit()
Idea 2) If you just want the historic data visible in the graph (i.e. you do not need to query or interact with the old data through the graph), and if your range is stable, then you could have one plot in the graph and use a PhosphorColorRamp to get the visual fade effect. In pseudo-code:
    // initial setup
    var brush = new SolidColorBrush( C )
    Graph.SetPhosphorMode( brush, Immediate )
    graph.Plots.Add( new Plot { Renderer = new Renderer( brush ) } )
    graph.RenderMode = Raster
    graph.PhosphorColorRamp = new FadeRamp { Color = C, Duration = 20, DurationKind = Frames }
    // on data update
    graph.Data[0] = /* assign new data to first plot */
(Note that the phosphor effect is one of the areas being updated, so the syntax will be changing in the next release of Measurement Studio.)
~ Paul H

How do you change multiple plot properties programatically?

How would you programatically change the color and line size of different plots? I know you create a property node but when I do that I don't seem to be able to specify which plot I want to change.
For example: plot 1 is green w/ dotted line, plot 2 is red with solid line.
I want to programatically change say plot 1 to a blue solid line and plot 2 to a yellow line.
There is a "plot name" property but no matter what name I specify it changes all the plots.

First, you have to use the "Active plot" property, as in the attached example...
CC
Chilly Charly (aka CC)
E-List Master - Kudos glutton - Press the yellow button on the left...
Attachments:
MultiPlot colors.vi ‏49 KB

Is it best to set waveform graph scale properties before or after sending new data to the graph?

Hi I'm wondering when is the best time to update waveform graph scale properties.
I am sampling data every 15 minutes for 192 samples, i.e. 48 hours. I want to plot these samples with the x scale in absolute time mode so that x scale maximum is the current time and x scale minimum is x max minus 48 hours (172800 seconds). I also want the intermediate scale markers to be 6 hours apart and to be multiples of whole 6 hours. e.g. at 06:00, 12:00, 18:00. This works OK using property nodes but sometimes the intermediate markers are on the 6 hour multiples and sometimes they are at 6 hours after the min scale marker. e.g. 09:15, 15:15, 21:15. Is there a way of guaranteeing that the intermediate markers will be on the 6 hour multiples?
Thanks,
Neville
Solved!
Go to Solution.

Hi Bryan,
Thanks for your reply. I have discovered that I can achieve what I want by using an XY graph instead of a waveform graph. I want X max to be the current time and X min the be 48 hours earlier with intermediate scale markers on multiple of 6 hours. The XY graph in the attached VI does exactly that but I can't get the waveform graph to behave as I would like. Is there a way of getting the waveform graph to behave as I would like?
Thanks,
Neville
Attachments:
waveform graph x axis scale.vi ‏16 KB

Create graphs with properties values

Hello!
I want to create a Bar Graph or a normal graph with properties contained in ChannelGroup level. Is there any easy solution to this?, so far is seems that the only option is to create a channel with this values, but I don't want to duplicate the information since I have a considerable number of channels in each Channel Group.
Thanks in advance for the support!

hello!
I know that you can get even the values or whathever property live values, name, etc. with the expresion form "@@ @@". However I want to plot, for example a bar graph that contains a numeric property of the group. Let's say that I have 3 Datasets all with a property "TotalFuel" and different values in each group, So what I will like to do is to plot this values in a 2DAxis object. But it seems that all the plots or graphs are meant to be only channel oriented.
Do you understand my issue? Please let me know if not to clarified better this.
Thanks!

Bode plot instrument reading differs when compared to grapher plot

Good Day,
Need some help to understand why the bode plot instrument plot (clicking the instrument to see plot) is different from the grapher plot when run in "simulate >>> analysis >>> AC analysis >>> vertical scale (db) >>> simulate.
Problem happens if the AC source AC analysis magnitude is changed from 1(default) to another value. i.e 6.
Please help advise, it seems the bode plotter is only considering the default AC analysis default magnitude value of 1?.
Appreciate comment on this. Thank you
The circuit being simulated is AC source connected to an RLC circuit and Vo is accross C. L and C assume some small series resistances.

Hi educ,
In the AC Analysis I set the stop frequency to 100 KHz which is the stop frequency of the Bode Plotter instrument. When I ran the analysis after doing this and compared it to the bode plotter, it was a nearly identical output. Try to configure the start and stop frequency to match in the AC Analysis and in the Bode Plotter and you should see much better results.
Regards,
Tayyab R,
National Instruments.

The item contains one or more busy items that cannot be changed

We have a Windows 2003 file server and we are having issues with Macs retrieving files/folders from it. There is a folder on the Windows share named "dropbin" that UserA has full permissions on. UserB has the following NTFS permissions on the dropbin folder.
Traverse Folder / Execute File Allow
List Folder / Read Data Allow
Create Files / Write Data Allow
Create Folders / Append Data Allow
Write Attributes Allow
Write Extended Attributes Allow
This gives UserB the ability to look inside the dropbin folder and place content in there. This same user cannot delete or pull down anything that a different user (UserC) has put in there. UserA (the person with full permissions) should be able to pull down anything put in there.
This works fine from an XP box if an XP user (UserB) puts content in there UserA from a Mac or a PC can get and manipulate the data. If a Mac user (UserB) puts a file up there (it seems to happen with a .txt file, a .cp file, or a .zip file) UserA from a Mac gets the following error when trying to download the file:
"You may need to enter the name and password for an administrator on this computer to change the item named item.txt"
When you hit continue you get the following error:
"The item item.txt contains one or more busy items that cannot be changed"
If you proceed to enter in the admin credentials, the file doesn't copy down to the local Mac and fails without an error.
A couple of things we noticed....
1. If Mac UserB puts up a Word document or a .dmg file then UserA from a Mac can pull it down fine without errors.
2. On the Windows 2003 server we noticed that for each file we tried to upload it creates a ._ corresponding hidden file. For example, item.txt also has ._item.txt. If we go up on the server and remove the hidden file, Mac UserA can pull down the file fine.
3. We tried zipping the files (or files and folders) locally on Mac UserB's desktop then putting the .zip file up there but since it creates a ._file.zip Mac UserA still can't pull it down.
4. The fix we found for this is to have Mac UserB place the files they want to upload into a folder on the desktop, then upload that folder. When Mac UserA comes by they can pull down that folder's worth of stuff.
We are accessing the Windows 2003 file share by going to the finder and using the "Go" menu and entering in:
smb://servername/sharename
and they use their Windows domain credentials to log in.

We may have figured this out but it requires some more testing. The reason why the file upload creates the ._ files in the dropbin folder when UserB puts content in there is because UserB does not have the "Delete" permission in that folder. My guess is that it creates the ._ file when the file is in transit but then deletes that file after it has completed the transfer (but without the delete permission it couldn't remove the ._ file). What we did was added another user to the NTFS permissions for that folder, we added the built in "CREATOR OWNER" account and gave that user the "Delete" permission, now the ._ files do not appear under there and UserA can come along and manage the uploaded file okay.
Hope this helps someone else out.

One or more busy items cannot be changed

I've dragged songs out of iTunes to a folder on the desktop, dragging this folder to my external HD the message "the item "..." contains one or more busy items that cannot be changed" comes up. The permissions for this folder are read and write so not sure what else to do. I've done this before and had no problems...

I finally sorted out a similar problem.
Discover which files are involved by copying the *contents* of the source folder to a destination.
The offending folder (or folders) should display by name. If the item is a file, the file name should display. You can drill down within a folder by the same process: copy the contents (not the entire folder) to a destination, to find the offending folder or item.
I ran across and old (2002) posting which mentioned file type as preventing deletion:
http://hints.macworld.com/article.php?story=20020920055805577
I found an old application which can display file creator and type on OS X:
http://www.frederikseiffert.de/filetype/
How old is it? The System Requirements are:
"FileType runs on Mac OS X v10.0 or later and on Mac OS 8.6 or later with CarbonLib 1.3."
It runs on 10.4. Haven't tested anything later.
I discovered that the file types on the offending files were "brok". It so happens they were all tiffs, so I changed them to "TIFF". I still got a message about needing to enter an admin user and password, but the copy then worked.

I am trying to authorize my computer and I get an error message: The required directory was not found or has a permissions error. Correct this permissions problem and try again, or deauthorize this computer if the permissions cannot be changed. Help?

I am trying to authorize my computer and I get an error message: The required directory was not found or has a permissions error. Correct this permissions problem and try again, or deauthorize this computer if the permissions cannot be changed. Help?

I used Terminal to change the permissions on the folder in question. I followed the instructions in this article:
iTunes: Missing folder or incorrect permissions may prevent authorization
In my case, the folder was there, so I needed the command to change permissions on the folder, not to create one. I was hesitant to use Terminal b/c I know that if I made an error I could wipe out my hard drive or render my computer unusable. So to be SURE I didn't make an error, I carefully copied the command from that page and *pasted* it into Terminal. Also, before I could do anything in Terminal, I had to go change my admin password (it had been a blank password before and that's not acceptable for making changes in Terminal). I was just super careful when entering my password or doing anything else while Terminal was open (making sure I didn't accidently hit the spacebar or another key, etc.) And it fixed the problem right away.
What was confusing for me was that the iTunes error message said to change permissions in the FINDER, which is what I was trying to do. It didn't mention Terminal. What would really be helpful is if Apple included a link to a page like this in their error message.

HT1296 I have a problem synching calendar data between my iPhone 3GS iOS 5.1 & Outlook 2007 on MS7. The basic calendar is OK but the birthdays (little box icon) are a day early & cannot be changed to the correct date. How can I fix this?

I have a problem synching calendar data between my iPhone 3GS iOS 5.1 & Outlook 2007 on MS7. The basic calendar data transfer is OK but the birthdays (little box icon) are a day early & cannot be changed to the correct date. The birthday entries in my Outlook contacts have correct dates.How can I fix this?

The following peocess corrects the calendar entry:
edit the contact & change the birthday, save the change; edit the contact & change the birthday to the correct value, save the change again. The calendar entry then displays on the correct date. Alternatively as a temp solution I can just de-select the "birthdays" calendar which stops the icon being displayed.
Thanks for your advice, I think that it's n going to be a slow process to fix all the entries for not much return.

Exchange Connector 3.0 (Hotfix Release) Error - Error Message=The key value of an object cannot be changed.

Hello,
I am running Service Manager 2012 with the Exchange Connector 3.0 RTM (Re-release Version). The issue I have is that when an e-mail is processed that is trying to update the status or event log of an incident, the Exchange Connector encounters an error
and will not update the object. The Operations Manager log denotes:
Exchange Connector: Unable to process mail item. Subject="Close Ticket: [IRXXXXX]", Error Message=The key value of an object cannot be changed.
This will happen on a seemingly random selection of Incident work items. I cannot correlate them with a specific template, exchange connector, or incident tier queue that could be causing the issue. I can recreate the way a specific ticket
was created and update it through e-mail without issue, and the next ticket can cause the error to trigger.
I have already opened a Microsoft Support Case using our Software Assurance agreement. After a few months of troubleshooting the issue and trying different fixes, Microsoft support said they were unable to fix the problem and that we would need to
purchase Premier support to go further. At this point I thought I would reach out to the community for ideas.
The setup I have for the Exchange connectors is as follows.
I have three separate Exchange connectors set up to three different mailboxes. One Exchange connector processes external support tickets and applies a specific template. Another processes client support tickets and applies a different template.
And the last Exchange connector processes internal tickets and also processes the updates of tickets created by the other two exchange connectors.
Here are the fixes I've attempted so far:
1. Changed the templates that each Exchange connector applies.
2. Changed the management pack that each template is stored in.
3. Checked my management pack(s) for extended classes by searching for Extension="true" (This was also checked by Microsoft support)
4. Deleted each Exchange connector and recreated each connector
5. Deleted each Exchange connector, deleted the management pack, and reinstalled the management pack and connectors
6. Repeated Step 5, deleted Microsoft.SystemCenter.ExchangeConnector.dll and Microsoft.SystemCenter.ExchangeConnector.resources.dll and then installed the Exchange connector Re-release version 3.0 Published 10/7/2013 (which is supposed to address this
issue)
7. Deleted the HealthServiceState folder and restarted the Management Service
I'm not really sure what to do at this point. I've put many hours into customizing my installation to get it working for my organization so reformatting and starting from scratch would be a nightmare scenario. This environment is in production.
I do have a band-aid in place using Orchestrator. Basically I have a monitor task searching for the error message and when it finds one it searches the mailbox for the offending e-mail and applies either the Resolve or Close status change that is requested
from the user. However, I do not have it working to update the ticket if a comment is applied to the incident. If anyone is in this position and needs to know how to apply this Orchestrator task I am willing to provide my workflow.
I am new to the community and am already impressed with the amount of help and effort there is in this forum. I appreciate in advance any help that is provided and am open to any ideas at this point. I can post more information as needed.
Thank you,
John

Yes that is the whole template. However, I did confirm that this is only happening to incidents where either of two situations triggers a runbook to fire and modify the incident. When I remove the activity from the incident it does clear the
issue. For some background the first Runbook Activity set's the first response date when an incident is resolved if the first response value is null. The second assigns the incident to a user upon creation if the title contains assignto:username;
1.)
<ObjectTemplate ID="Template.d33b5bbcaf3c49b18d8b72bc1e5e1ee4" TypeID="IncidentManagement!System.WorkItem.Incident.ProjectionType">
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Incident_Library!System.WorkItem.Incident']/Escalated$">False</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Incident_Library!System.WorkItem.Incident']/NeedsKnowledgeArticle$">False</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Incident_Library!System.WorkItem.Incident']/HasCreatedKnowledgeArticle$">False</Property>
<Object Path="$Context/Path[Relationship='CustomSystem_WorkItem_Activity_Library!System.WorkItemContainsActivity' TypeConstraint='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity']$">
<Property Path="$Context/Property[Type='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity.Base']/RunbookId$">4085f0da-ab83-48e5-bbe3-1f3b5fa2dc4a</Property>
<Property Path="$Context/Property[Type='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity.Base']/TemplateId$">Template.d33b5bbcaf3c49b18d8b72bc1e5e1ee4</Property>
<Property Path="$Context/Property[Type='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity.Base']/IsReadyForAutomation$">True</Property>
<Property Path="$Context/Property[Type='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity.Base']/PropertyMapping$"><?xml version="1.0" encoding="utf-16"?>
<ParameterMapping xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
<ParameterList>
<RunbookParameterItem>
<Name>Get RA Guid</Name>
<Id>344b15effc1a44528e517c5b4227179c</Id>
<Type>String</Type>
<Value>Generic::Id</Value>
<Direction>In</Direction>
<ContextInfo />
</RunbookParameterItem>
</ParameterList>
<RunbookId>4085f0da-ab83-48e5-bbe3-1f3b5fa2dc4a</RunbookId>
</ParameterMapping></Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Activity_Library!System.WorkItem.Activity']/ChildId$">1906</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Activity_Library!System.WorkItem.Activity']/Status$">$MPElement[Name='CustomSystem_WorkItem_Activity_Library!ActivityStatusEnum.Active']$</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Activity_Library!System.WorkItem.Activity']/Skip$">False</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Library!System.WorkItem']/Title$">Set First Response on Resolve</Property>
</Object>
</ObjectTemplate>
2.)
<ObjectTemplate ID="Template.b311e1f9126e4e19bbbbeb65ddb220ba" TypeID="IncidentManagement!System.WorkItem.Incident.ProjectionType">
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Incident_Library!System.WorkItem.Incident']/Escalated$">False</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Incident_Library!System.WorkItem.Incident']/Status$">$MPElement[Name='CustomSystem_WorkItem_Incident_Library!IncidentStatusEnum.Active']$</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Incident_Library!System.WorkItem.Incident']/NeedsKnowledgeArticle$">False</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Incident_Library!System.WorkItem.Incident']/HasCreatedKnowledgeArticle$">False</Property>
<Object Path="$Context/Path[Relationship='CustomSystem_WorkItem_Activity_Library!System.WorkItemContainsActivity' TypeConstraint='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity']$">
<Property Path="$Context/Property[Type='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity.Base']/RunbookId$">ca88b13b-861a-4d39-a3cb-fd912d951e35</Property>
<Property Path="$Context/Property[Type='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity.Base']/TemplateId$">Template.b311e1f9126e4e19bbbbeb65ddb220ba</Property>
<Property Path="$Context/Property[Type='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity.Base']/IsReadyForAutomation$">True</Property>
<Property Path="$Context/Property[Type='CustomMicrosoft_SystemCenter_Orchestrator!Microsoft.SystemCenter.Orchestrator.RunbookAutomationActivity.Base']/PropertyMapping$"><?xml version="1.0" encoding="utf-16"?>
<ParameterMapping xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
<ParameterList>
<RunbookParameterItem>
<Name>RA Activity GUID</Name>
<Id>5677d117a0294a2c898a695032f26c72</Id>
<Type>String</Type>
<Value>Generic::Id</Value>
<Direction>In</Direction>
<ContextInfo />
</RunbookParameterItem>
</ParameterList>
<RunbookId>ca88b13b-861a-4d39-a3cb-fd912d951e35</RunbookId>
</ParameterMapping></Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Activity_Library!System.WorkItem.Activity']/ChildId$">1120</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Activity_Library!System.WorkItem.Activity']/Status$">$MPElement[Name='CustomSystem_WorkItem_Activity_Library!ActivityStatusEnum.Active']$</Property>
<Property Path="$Context/Property[Type='CustomSystem_WorkItem_Activity_Library!System.WorkItem.Activity']/Skip$">False</Property>
<Property Path="$Context/Property[Type='WorkItem!System.WorkItem']/Title$">Execute Orchestrator IR - Autoassign</Property>
</Object>
</ObjectTemplate>

Error message: iMovie cannot save changes to the library!?!

iMovie crashed my computer and now I can't creat a new movie.
Here's the full error message:
iMovie cannot save changes to the library.
The hard disk where your library is located may be full or unavailable or permissions may have changed. To avoid losing your work, quit iMovie.
What's up with this? I tried trashing the preferences, but got the same message. I have a 27-inch late 2013 iMac running Mavericks with 445.55 GB free space.
Please let me know if you have any suggestions.

You've already tried trashing iMovie preferences (By the way think in Mavericks you have to reboot as well after this for the new preferences to take effect) . One other thing to try is creating a new user account, logging in and seeing if you can create a new project in iMovie (of course you won't see your exisitng projects). If you can then iMovie itself is OK. If not then the only other thing I can think of is re-installing iMovie (see http://macs.about.com/od/usingyourmac/qt/How-To-Re-Download-Apps-From-The-Mac-Ap p-Store.htm)
Is everthing else working OK after your computer crash? Maybe you should also run Verify disk in Disk Utility.
Maybe someone-else has some other suggestions (I have not heard of this problem before)?
Geoff

Novated Purchase orders cannot be changed error

Hi Experts,
while trying to edit the PO we are getting an error as " Novated Purchase orders cannot be changed" . I am confused that which field is used to differentiate the normal PO to that of novated PO at portal level. Please let us know why this error occurs and how can we solve the issue ?
Thanks in Advance.
Thanks & Regards,
Aishwarya.M

Hello Aishwarya ,
A Novation is agreement of parties usually done in conjunction with an assignment where upon the assignment there is now a new agreement between the original party whose contract was assigned and the party to whom the contract was assigned that in effect extinguishes (cancels) the old agreement and relieves the assigning party of liability under the contract.
For example if A and B have a contract and there is an assignment and novation of that contract by B to C, the contract would now be between A and C and B would no longer be liable to A under the contract as the “novation” extinguishes their liability.
If you wanted to prevent a novation you might include something like the following:
“This contract shall be binding on the parties and their respective successors and permitted assigns. Except in the instance of an assignment or transfer by Buyer of all or any portion of this agreement, the assigning party shall remain liable for the performance of any assigned or transferred obligations hereunder.
The requirements for a novation may vary by jurisdiction. For example in New York for there to be a novation it must specifically say it is a novation. In assignment consent letters Suppliers may try to create a novation by the words they use where the language in affect would say that Buyer may only look to the new entity going forward. Please check with the PO which supplier is being used and also check is there any third party involvement in that PO.
Thanks
Gaurav Gautam

3D graph plot properties - cannot be changed

Similar Messages

Maybe you are looking for