6500 xconnect and QinQ frames

Hi, I want to pass all vlanes from a client. I have a tunnel-port in both 3560 and then I have an mpls xconnect between 6500. The 6500's are connected with a pvc with encapsulation aal5snap. This is the schema:
3560 --Gb -- 6500 -- ATM PVC -- 6500 -- Gb 3560
The problem is that the xconnect does not carry QinQ frames, it only sends the frames from the client that are untagged.
How can I pass the QinQ frames between the 6500's?
Thanks

This is the current 6500 configuration, I have tried with the same result this configuration and other using subinterfaces. The xconnect works because I could see the untagged frame int both sites. The interface Gig1/9 from the 6500 is connected with the interface Fa0/1 from the 3560.
interface GigabitEthernet1/9
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
mtu 9216
no ip address
interface Vlan3003
description VLL_CLIENT1
no ip address
xconnect 10.0.0.3 3003 encapsulation mpls
show modules:
#sh mod
Mod Ports Card Type                              Model              Serial No.
1    9 Supervisor Engine 32 8GE (Active)      WS-SUP32-GE-3B     SAL12426MVE
2    0 4-subslot SPA Interface Processor-200 7600-SIP-200       JAE1244Z5PF
Mod MAC addresses                       Hw    Fw           Sw           Status
1 0021.d89e.c846 to 0021.d89e.c851   4.6   12.2(18r)SX2 12.2(18)SXF1 Ok
2 0021.a06d.fdc0 to 0021.a06d.fdff   2.303 12.2(18)SXF1 12.2(18)SXF1 Ok
Mod Sub-Module                  Model              Serial       Hw     Status
1 Policy Feature Card 3       WS-F6K-PFC3B       SAL12405HZN 2.4    Ok
1 Cat6k MSFC 2A daughterboard WS-F6K-MSFC2A      SAL12426HJD 4.0    Ok
2/0 2xOC3 ATM SPA               SPA-2XOC3-ATM      JAE1244Z6G2 1.1    Ok
Mod Online Diag Status
1 Pass
2 Pass
2/0 Not Applicable
The 3560 configuration is this:
interface FastEthernet0/1
description 6500_Uplink
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/8
description CLIENT1
switchport access vlan 3003
switchport mode dot1q-tunnel
l2protocol-tunnel cdp
l2protocol-tunnel lldp
l2protocol-tunnel stp
l2protocol-tunnel vtp
no cdp enable
Thanks in advance

Similar Messages

Playback of clips only plays between 4 and 12 frames

Hi all,
I am fairly new to Premiere, have used After Effects CS4 to produce some clips, but need something that handles editing better, and I thought I would give Premiere CS4 a try.
Unfortunately, I can't get Source or Sequence preview working. I click the play button and the video plays for about 1/2 to 1/4 or a second (between 4 and 16 frames) and then stops, returning to the place where I hit play. Almost like I had selected an in and out of 14 frames and hit "play in to out".
The duration of the playback is random, but never more than a full second.
The computer I am on is:
Model Name: MacBook Pro
OS: Snow Leopard 10.6.2
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
L2 Cache: 3 MB
Memory: 4 GB
Bus Speed: 800 MHz
Chipset Model: GeForce 8600M GT
Bus: PCIe
VRAM (Total): 256 MB
Vendor: NVIDIA (0x10de)
RAM Size: 4 GB
Type: DDR2 SDRAM 667 MHz
HDD: 500Gb 7200RPM (50% empty)
Apple system updater says I am up to date.
I have Adobe Premiere CS4 installed (trial) 4.2.1 (003 (MC: 166418))
Adobe Updater says I am up to date.
I have done the following to try and resolve:
* Tried different source files (mp4, mov)
* Tried rendering a video in After Effects CS4 as MOV H264 and importing
* Tried putting still frames on the time line and playing those (no effects, no transitions)
* Tried playing no video, just music
* Ensure that "clear all markers" is done on the source and preview monitors
* Ensure loop is not playing
* Force in and out markers to a 5 second clip and press play
* Full deinstall and reinstall of all adobe products (I had some CS3 left overs that I cleaned out)
* Deleted all adobe application preferences folders before reinstall
* Deleted plugin cache
* Created new projects and tried all the above.
I have tried shutting down every other program before running Premiere, it is definitely not a resources problem, there is 3Gb of RAM free and CPUs sitting at 5% when I try this.
I am looking at buying Premiere, but if I can't get playback to work it's a bit of a waste
Anyway, any help or pointers would be appreciated!
Mikel

Thanks everyone for the long thread and lots of comments, unfortunately I have tried them all.
I even purchased a full copy of Premiere Pro (as part of a Masters collection set) and this still has not fixed the problem.
The screen recording of my problem is exactly the same as the one linked to here: Screen Recording 2 720p.mov, and I am also going to open a support ticket with Adobe.
Another point is that it even does not work on a tiny video that I used (320 x 240px) Still same problems.
This is very frustrating.
It should be noted that After Effects and Encore both play videos fine in a similar situation, it is just Premiere that is bombing out.
See the first post for my configuration, it is still the same, except now I own a full copy of Premiere Pro as part of CS4 Masters collection.
Any further ideas?
Mikel

Hello, 2 questionss here is it possible or is there a way to convert all object s outlines in all frames to fills at once and not frame by frame? and why sometimes erases the outline instead of converting it to fill?

Hello, 2 questionss here>is it possible or is there a way to convert all object s outlines in all frames to fills at once and not frame by frame? and why sometimes erases the outline instead of converting it to fill?

Hello, 2 questionss here>is it possible or is there a way to convert all object s outlines in all frames to fills at once and not frame by frame? and why sometimes erases the outline instead of converting it to fill?

Can only see first and last frame of clip in the timeline HELP PLEASE

Hi, my first time and I did look for an answer, but can't find one. I have premiere elements 4 and I am trying out ver. 9. In ver. 4 the clips in the timelin shows all the frames, but in ver. 9 it only shows the first and last frame of the clips. Is there any way to make all the frames show. By "all the frames", I mean the clips fill with frames.I liked to see all the frames in the timeline, it is easier for me to select and trim the bits out.
My specs are Core 2 Duo 6750, Nvidia 8600GTS, 4G Ram, Vista Home Premium. 3 HDD 3TB.
Thank you for answering
Werner

As for the GUI, PrE had one more like PrPro (the early versions), up through PrE 3. With PrE 4, they streamlined the GUI (and some of the operation), and went with the "dark look." PrPro went in that direction starting with CS3, and now, the two programs' GUI looks more alike - darker. Personally, I like PrPro 2.0's brighter GUI. Now, one can alter the brightness, but the contrast can work against doing much of that - give me the lighter GUI....
The look of PrE 4 thru PrE 9 is very similar, though things have moved about some. Still the look is similar. Same for PrPro CS 3 through CS 5.5.
As for the trial, things have changed in PrPro, as of CS 5.5. Once, the PrPro trial was very crippled, but had no watermark. No more. No crippling, and still no watermark. The trial for PrE is far less crippled, but does have the watermark. We do not know what changes might be coming with the trial of PrE10. We will just have to wait and see. One great option that Adobe offers is the 30-day, money-back guarantee. If you buy Premiere (either flavor), and use it for 29 days, but do not like it, then you return it for your money back. This is the full-paid version (both flavors) with nothing crippled, and no watermark. Not that many companies make such an offer. Basically, on can use the trial for 30 days, to see some of the powers of the program, and then buy it, and try it fully for another 29 days. If not completely satisfied, they get their money back - essentially a 59 day trial.
Were I doing AVCHD, I would definitely look at buying PrE 9, and giving it a 29 day shakedown. The only caveat is that AVCHD requires a lot of computer "horsepower," and not all computers (especially if more than a year, or so old) are up to that task. I find it amazing that a consumer format, like AVCHD, requires more computer power to process, than most professional formats, until one gets up to, say RED 2K/4K. However, that is the nature of the H.264 CODEC, and by that, I mean all H.264, not just the AVCHD version.
Good luck and happy editing,
Hunt

HP 6500 Printer and prints very faintly.

I changed my ink cartridges in my HP 6500 printer and it now prints very faintly or when I send a test print to the printer from my computer it will only feed the paper thru the printer.

The document here may help resolve black not printing on your Officejet 6500. Be sure to check the vents as shown in solution three. If this does not resolve the issue the post here may help.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Effects and key-frames not working on some clips Premiere CC 2014

Hi. I am having an issue where effects and key frames applied to both audio and video are not working, but only sometimes. Even after I render or export the video, the effects are not showing up. For example, trying to adjust volume using key-frames on some clips works fine, and not at all on others. The key-frames show up and I can see the volume changing in the effects panel, but it is not happening. Another example is changing the opacity on some video clips and it does not work sometimes. Same thing, I can see the key-frames and the values changing, but it's not actually happening. I have uninstalled and re-installed premiere pro and media encoder with no luck. I have uninstalled and re-installed the latest Nvidia drivers with no luck. Just to restate, this only happens on some clips and rendering or exporting the video does not help. My computer specs are:
MSI GT60 Laptop:
Intel Core i7 4800MQ (2.70GHz)
16GB Memory 1TB HDD 128GB SSD
NVIDIA GeForce GTX 880M 8GB
2880 x 1620 16:9 3K Display
Windows 8.1 64-Bit

Here is the exact screenshot. Now I'm also trying other effects as stated in my original post. But this effect is just an example. Is there really something that I'm doing wrong here? Or am I forgetting something? Is there some special "adobe doesn't let keyframes work on mpg's" rule or something silly like that?
I wish that I could post a video, but I don't know how.
Please let me know what I need to do to make this work properly.
TEX

AE CC 2014 Corrupted and Glitched frames when rendering to Quicktime

Ever since upgrading to the newest version of After Effects, I've been getting corrupted and glitched frames when rendering videos with a Quicktime holder. My normal workflow is rendering the video straight out of AE, but it also happens when rendering with Adobe Media Encoder, or even while using the "BG Renderer" script for AE that renders from the terminal. It happens whether I have multiprocessing enabled or not.
The corruption differs depending on what codec I'm using, but in the Cineform Codec it shows up as green frames:
On DNxHD they show up as Red frames (don't have a screencap of this one but you get the idea).
Using the QT Animation Codec they show up as static or distortion:
I have not found a codec that does not become corrupted when encased in the QT holder. Image sequences render out fine, and Cineform with an AVI holder renders out fine.
Even more strangely, I can fix the problem if I link the AE composition to Premiere, then render the QT file out through Premiere itself. The fact that Premiere calls and renders the Comp fine but AE does not, makes me think this is a bug in AE's treatment of Quicktime rather then a driver/system incompatibility on my end. But I'm certainly willing to try any suggestions the community might have for me =]
Specs:
Windows 7 64-bit
AMD Firepro V7800
AMD Phenom II X6 1090T
16 GB RAM
Rendering to a local drive
Fully Updated AE
Latest version of Quicktime

solutions for problems with QuickTime files in After Effects CC (12.0) because of conflict with DVCPROHDVideoOutput Quic…

Problems working with non drop and drop frame DVCPRO HD material in project

I am having playback problems with my non drop frame HDV material. It stutters.
All of our projects up to this point have been shot in drop frame. During our last shoot however the Bcam was recorded in non drop. I loaded both the non drop bcam tapes as non drop and the drop frame Acam tapes as drop. All of the drop frame Acam material plays back fine in the source viewer and the timeline. The non drop Bcam material seems to randomly stutter in the source viewer, or causes the system to serve a "dropped frames warning" in the timeline.
Is there a bug with fcp 5.1.2 about mixing non drop and drop frame material in a project. Or is this not possible? They are the same frame rate.
I have exported the non drop clips in a drop frame timeline and re-imported them as drop frame clips - thus correcting the problem. Is this the best solution?
All of the material was loaded thru a kona card as 1080i60 DVCPROHD 29.97
I had no problems capturing the material as long as I used the corrrect firewire setting (ndf vs df).
Anyone have a problem like this? I would greatly appreciate a response.
Thanks,
Mark

http://bssc.sel.sony.com/BroadcastandBusiness/DisplayModel?m=10014&p=2&sp=141&id =78439
The camera can record 60i, and 30F:
"HDV 1080, 50i/60i/30F/25F Recording and Playback capable"
Look at the clips...look at their frame rates. What do they say? Is one 59.94? Is the other 29.97?
You would never need to render if you mixed NDF and DF footage. The footage runs at the same speed, on the TC numbers are different. But, you would need to render if your footage had different frame rates. LOOK AT THE CLIPS.
Shane

Accessibility: Reading order of tables and anchored frames

I am creating accessible, tagged (section 508 compliant) PDFs in FrameMaker 9. The reading order for tables and frames is not correct.
When I view the PDF reading order using Adobe Acrobat Professional or another screen reader, anchored items such as tables and anchored frames are placed last in the reading order, regardless of where they appear in the document flow or page layout. The reading order skips over all tables and frames, reading all paragraphs on a page first, then reading the tables and frames as the last objects on the page. This logically doesn't make sense to skip over tables/frames as they generally apply to the content that preceeds it.
For example, the following document structure:
<Paragraph 1>
<Table 1>
<Paragraph 2>
<Anchored Frame 1>
<Paragraph 3>
<Anchor Frame 2>
<Paragraph 4>
is being read by assistive technology as:
<Paragraph 1>
<Paragraph 2>
<Paragraph 3>
<Paragraph 4>
<Table 1>
<Anchored Frame 1>
<Anchor Frame 2>
I want the document structure to be read correctly as intended.
In otherwords, the PDFs generated by FrameMaker 9 are not completely accessible because of incorrect reading order output by default. This information is not listed in the VPAT for FrameMaker 9.
I want to avoid any post processing using Acrobat's Touch Up Reading Order tool. Is there a way to automate updates to reading order?
Can FrameMaker 9 logically place tables and anchored frames into the correct reading order? How do I adjust these settings?
Thanks in advance!

As mentioned above, tables and anchored frames are inserted into thier own paragraph style "Frame". The paragraph style "Frame" is tagged. To my knowledge, there are no options for tagging or not tagging tables or anchored frames.
Regardless of which paragraph type the table or anchor frame is inserted into, and what that paragraphs tagging settings are, it is still last in the reading order.
I've tried a variety of options: tagging the "Frame" paragraph style as a sibling, child, and parent of my other paragraphs; I've even tried omitting it from the reading order. None of these options present anchored frames (and tables) in the logical reading order.
Even images that are inline (within a paragraph; not in thier own paragraph) are not being read as part of the paragraph. Inline images get skipped over by screen readers and get read at the end of the page, which makes no sense whatsoever.
All tables and images end up at the end of the reading order (after ALL paragraphs) regardless of the tagging settings.
Refer to my previous screenshot for a clear diagram of what is happening to the reading order. Each of those anchors is in it's own paragraph style. I want tables and anchored frames to be sequential in the reading order along with paragraphs. (1,2,3,4,5,6 not 1,4,2,5,3,6.)
I'm using the Tags tab of the "PDF Setup" dialog to adjust these settings. Is there somewhere else I should be making changes to the reading order?
This is a bit disturbing because FrameMaker touts creating accessible documents and this severe reading order issue impares my ability to do so. I would not consider documents that jump around the page in an illlogical, fixed order, to be accessible. I'm very suprised that no one else has encountered this issue (at least that I can find...)

In an inbuild example of can .. that CAN transmit periodic vi .. i am unable to understand how the extended and standard frame is set?

In an inbuild example of can .. that CAN transmit periodic vi .. i am unable to understand how the extended and standard frame is set?
plz help me .. stuck up very badly
thanks
mahadev
Solved!
Go to Solution.

I suggest this KB which explains usage of Ext IDs with NI-CAN
http://digital.ni.com/public.nsf/allkb/2FA120A37EDBC51D86256854004FB0C7

Copy and paste frames is CS3

I'm going from mx to cs3 and can't find the copy and paste
frames option that used to be in the edit menu. Can anyone help
with that?

select all the frames you want to copy, right click, copy
frames.. in new doc, right click on a frame, paste frames

My SD video keeps jumping between the upper and lower frames. So the video starts frame blending and blurring in and out.

My SD video keeps jumping between the upper and lower frames. So the video starts frame blending and blurring in and out. The sequence settings are set to
Editing Mode: DV NTSC 29.97 frames/second.
Pixel Aspect Ration: D1/DV NTSC (0.9091)
Fileds: Lower Field First
Display Format: 30fps Non-Drop-Frame Timecode
720 x480

What is the source of your video, and exactly what is inside your video?
Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
http://forums.adobe.com/thread/592070?tstart=30 for screen shot instructions
Free programs to get file information for PC/Mac http://mediaarea.net/en/MediaInfo/Download

I want to know the exactly when the Kinect gives depth frame and color frame in a period of one frame

Hi, I'm currently using Kinect for Windows v2 to get a blurry sequence of color frames as well as corresponding depth frames.
It seems to me that the depth frame is acquired after the exposure time of the color frame. I am using the sample in the CoordinateMappingBasic to acquire the depth frame and the color frame at the same time.
But as i've found out by the aligned depth map with color frame, i think Kinect gives depth frame at the end of the exposure time of color frame. I've tried to obtain timestamps by calling a function iColorFrame->get_relative_time, and for the same number
the timestamps show that depth frame is acquired prior to color frame, which opposes what i said above..
Is there some way that i can know the exact time the Kinect gives depth frame and color frame in a period of one frame.
Thank you in advance.

Depth is generated based on IR information so when you acquire the frame, that is when it was created. Using the Multisource Frame Reader(MSFR) this does a lot under the covers to align the color and depth frame. If you want to do your own synchronizing,
you can use a polling thread to acquire depth on one and color on the other and do your own mechanism that is similar to MSFR. You will never get Color and Depth to align exactly on a particular timestamp. Since color is its own camera, the only thing
you can be assured of is when the color frame is acquired, the runtime will give you the closest depth frame that will align to it.
Carmine Sirignano - MSFT

First and last frame disappearing off every clip

Hi,
Every clip I import in Final cut pro 6.0 loses its first and last frame.
The clips I import are in photoJpeg / 24p (verified with the -get info- of Quicktime Pro), but once in FCP they are marked as 23.98 ?!?!
In the browser the info of the clip says 23.98 and also indicates that the clip is 2 frames shorter.
When opened in the viewer the first and last frames are really missing.
It gets worse, when a clip is longer (ie: 500 frames), the first and last TWO frames are missing ?!?!
Am I alone with this problem?
Please help!!!

How are these clips getting created? Quicktime does not necessarily associate each frame with a certain TC, and the frame rate is dynamically calculated, rather than simply being hard-coded into the QT metadata. This results in Quicktimes that get created outside of FCP often showing up with different frame rates than you expect.
You might try exporting movies back out of FCP, ether from the master clips, or from sequences. I have noticed that when I export from a sequence at the correct frame rate, the missing frames come back. Other tools that might come in handy are Compressor for converting batches of files to QTs that FCP will like better, and Cinema Tools for conforming clips to a particular frame rate (like changing them from 24 to 23.98)
You might also try Dumpster which is a bare-bones utility that will allow you to view and edit the QT metadata directly.
Try some experiments and post back and let us know what you find out. I found that placing the clips in sequences at the proper frame rate and exporting new movie files worked well, but I have seen timing and frame rate shifts with some clips using this method...
Hope this helps -
Max Average

When i Place a PSD in Indesign it comes in at 200+% while the image frame is considerably smaller. How do i place so that the image and image frame match?

When i Place a PSD in Indesign it comes in at 200+% while the image frame is considerably smaller. How do i place so that the image and image frame match?

Peter,
The screenshots tell you everything.
The second one tells you how the image frame is automatically set up after a one-click place. It's the blue stroked rectangle with the eight control points at each corner and mid-way along the line. This image frame is generated at a proportionally correct height and width for the image it contains.
Now, if you look at the third screenshot (click on it to see it at a larger size), you will see I've used the direct selection tool (white arrow) to click on the image within the image frame. This CLEARLY shows the image (within the image frame) is substantially larger than the frame generated to contain it. This is indicated by the yellow stroked rectangle with the eight control points at each corner and mid-way along the line.
Notice that the blue and yellow rectangles are vastly different sizes.
In InDesign CS5.5, when i clicked to place the image, the image would fit perfectly within its image frame. the blue and yellow rectangles would match.
I had no need to go click on the proportional fill and centre buttons like i need to do now in CC.
I have a keyboard shortcut to place. I can't do File > Place for the amount of images i need to place.
So to reiterate: How do i place an image so that the image and image frame match?

6500 xconnect and QinQ frames

Similar Messages

Maybe you are looking for