6600GT with new cooler

I have this card MSI NX6600GT-VTD128 Geforce 6600GT AGP, and have recently bought new cooler Zalman VF700. I connected everything and started windows, coolers works perfectly but when windows starts it still reports this:
"To protect your hardware from potential damage or causing a potential system lockup, the graphics processor has lowered its performance to a level that allows continued safe operations."
I'm guessing that that is because for my card cooler need to be plugged directly on graphic card, i think its called power molex or something , but Zalman draws power from PCU and i cannot connect it to graphic card.
What should i do?
ty

PERFECT , its working. Few more things, cable which is going from zalman goes into converter and then into 4pin molex cable, what if i plug in that into VGA instead of free 4pin cable?
And are settings now back on normal? or do i need reset them somehow?
Ty alot for all help

Similar Messages

Replacing msi gt60 ( cooler boost ) with new ( cooler boost 2 )

Hello
i have msi g60 0nc and its new
can we Replace the cooling fan with the new one with lower noise and better cooling ...
( cooler boost with new cooler boost 2 technology )

Quote from: darkhawk on 03-February-14, 01:57:54
I'll be perfectly honest....it's very simple airflow mechanics. This isn't rocket science.
If you look at this logically, and understand how the airflow works in the notebook, you'll see what I mean.
The best you can really hope for is building your own cooling pad to force air into the places you need it to go. That's what I did and it works wonders for the notebook.
The fan used in this is a particular fan. If you remove the bottom panel you should see what I mean. The blades are oriented differently from a normal 'PC Case' fan, since this is actually more like a 'blower' than a fan. Because of this fact, it makes them more difficult to find. On top of that, you'd need to find one that is the same size, as well as having close to the same or similar mounting points.
Needle, meet haystack.
My friend i think gt 60/70 2012 notebooks is the same design and build as 60/70 2013 notebooks with enhanced things like the cooling and the noise and both are powerful machines
so the point if we just cold enhance something in our notebooks especially the noise !

Has anyone experienced wrist pain with new mac computer...? if so what are suggestions other than warm up and cool down exercises..**

Has anyone experienced wrist pain with new mac computer...? if so what are suggestions other than warm up and cool down exercises..**

Very good advice but no one is asking for medical advice.... Was wondering if anyone had any ergonomic suggestions that may have worked for them.. ??

B2 Error with new MSI GTX 970 :(

Hi there team!
Just registered to try and get help. I spent around 6 hours researching + trying all the suggestions throughout many different forums, but the B2 error still persists. I am currently running the following spec:
Mobo - MSI Z68A-G43 (G3), with version 4.30 ( I flashed bios last night and still no help)
CPU - Intel® Core™ i5-2500K Processor, 3.5GHz etc.etc.
RAM - Corsair Vengeance 2x4gb at 1333MHz
GPU - MSI GTX 970 GAMING Twin Frozr V 4GB GDDR5
PSU - Cooler Master Silent Pro 700W
I have tried:
-Taking out the card and using the on-board graphics to flash the bios to later version, No help. (during this process, the B2 error does NOT show up)
-Upgraded the card to latest nVidia drivers, even uninstalled and re-installed them. No help.
-Upgraded all the drivers from MSI, i.e. chipset etc. through Live Update 6. No help.
When the card is in, I cannot even access bios, it just gets stuck at B2 screen for like a minute, and then carries on with the boot process. I am able to play games etc. after the booting, but this error for sure should not be there when the PC boots up. I didn't have any issues with my old GTX 560 TI. I've read different forums saying that it might have something to do with the mobo thinking that something has to be connected to the on-board graphics; or that flashing BIOS helped a lot of users, but not me :(.
I don't have a second PC to test the card on.
Literally, I would try anything, please someone just help :(( This card is a beast and I wanna be able to properly use it and not having to worry about this error.
Thank you very much guys, hope someone can help!

Quote from: gabe_dimitrov on 08-February-15, 20:40:51
Man thank you so much! It is finally working!!! Thank you!!!! ))) It is showing correct version in BIOS, does not show B2 error whatsoever, all done! )
Thanks for your time! You can close thread, but it's very useful for anyone that has this issue!
Wich version of BIOS do you have installed? Can you OC your processor with new BIOS?

'A problem with the cooling system' error message on Satellite A660

Hi all,
Hope I can get some help here. I've had about 5 HP laptops after all of them had problems and faults. I got sick of them and therefore got a refund and bought a high spec A660-1FH.
The A660 has been a great laptop for two days until yesterday when I started getting a warning message saying 'A problem with the cooling system has been detected. Please turn off the computer immediately, and return it for service'.
The cpu fan works fine as you can here it spinning and the temperature of the i5-460m processor is around 40 degrees for both cores - which seems normal to me. I've noted that it happens only when running on battery and if you switch from eco utility to power saver mode. Its fine when running on the 'balanced' power setting. The fan is louder before when this message appears.
As its under 28 days my retailer swapped it for a brand new one straight away. Got the new one home, and the same message appears again. Has anyone else experienced this. As two laptops have had this, I'm wondering if this is normal for the A660 series laptop or if there is really a hardware issue?!
I have tried to upgrade eco utility and the bios of the laptop but both are the latest versions. Can anyone help or share if they experience a similar issue with their laptop?
Thanks

In front of me I have Satellite A660-13Q (PSAW3E) and I have it about 6 weeks now. It runs almost 10 hours daily and until now I didnt notice such message or anything else that can be suspect for hardware functionality.
I really dont know why this happen on your notebook and dont think there is anything you can do about it.
I would exchange it again. What you can also try is to contact nearest Toshiba service. Make a call, explain the situation and ask if they can help you with this.

A problem with the cooling system has been detected

I bought a new computer not to long ago, I've had it for almost a month now. It runs fine, and I've had no problems until not too long ago. I was playing a game, and I got a random error message: "A problem with the cooling system has been detected. Please turn off the computer immdiately, and return it for service." I don't understand how or why this came up, and I don't have any money to return it for any type of repairs. After I got this message, I left my computer off for about an hour. All seems well so far. Any suggestions?

What laptop do you have?
- Peter

Several problems with new itunes??!!

Getting much of the same issues with new version of itunes. Printing up cd covers, the playlist gets all jumbled up for some reason. Also, the thing that really gets me livid is before you used to be able to randomize your playlist and the order would change. This was cool if you were going to burn a cd and just wanted a random order different than the order you put the songs in your playlist. Now it seems you have to move the songs around instead of itunes "shuffle" changing the order for you. The shuffle does work for playback but not when you want to burn your cd in a different random order like the old itunes used to. I also used to like the old itunes that would show the cd artwork bigger during playback. Now it doesn't seem to have that feature. "Recently Played" folder doesn't appear to work as well. Itunes Store appears to be much slower while searching for music and tends to freeze up a lot. Sampling songs in the store also seems to need to "rebuffer" way more than the old version. Most of the time, I don't mind the updates. It takes some time getting used to it but eventually it gets easier. This update, however, I am not very happy with. Especially not being able to shuffle my "playlist" order. That ***!!

looks like this is a known issue for the album covers printing jumbled. several work arounds would be to try print in black and white theme. You can also try to save as a pdf and print from another application like word or paint or something

My new cooler

hi, i finally decided on wut heatsink to buy, finally installed it too
i got the vantec aeroflow, man what a pain to install. but temps are showing very good right now.
i was wondering. with the wire where the heatsink gets its power from it has 3 pins and 3 wires. but in speedfan, i get no readings on the fan speed the fan is running on. so i was curious if it was like this or there is something wrong somewhere.
my temps on the stock cooler was 44 idle and 63 load
on the new heatsink it is 40-43 idle and 47 load, wow that is so nice
so any of u got suggestions on how to be able to know how fast the fan is spinning?
thanks, jofrad

Quote
o and since i added the new cooler, my northbridge temp went up which was weird, know any reason for this?
jofrad,
The way I understand PC thermodynamics, this could be from 3 separate causes, separately, or in unison in some combination of any/all.
1) Your new cooler could be blocking more convecting air to/from the northbridge.
2) Your new cooler may be radiating and/or convecting more heat to surrounding components, including your northbridge.
3) Your PSU may be working a bit harder, radiating and/or convecting more heat to your surrounding components.
(Additionally, you might be ranging into the upper end of your PSU's capapbilities, slightly lowering your voltages during heavier use, which will result in drawing slightly more amperage through your motherboard, and increasing the temps. I checked your PSU's specs, as well as your current power draw [294 Watts], using the components in your sig. Considering the Antec's over-wattage capabilities, you're probably ok in this department, but only ok, as you have a combined 3.3v and 5v of 230 watts, and 330 watts with the 12v included. At this rate, your maximum PSU usage is about 90%, which is 20% higher than the recommended max of 70%, with 50% being the ideal. If you have more components than those listed, this 90% might be higher.)
Before I upgraded my PSU, I wasn't happy with my temps or stability. I added another case fan (increasing total power draw), and both problems got worse. I then upgraded my PSU, and both problems went away.
A slight rasing of your NB temps shouldn't be much of a problem, if you don't experience any instability. If you do experience instability, you might want to check out a new Antec (or similar spec'ed PSU) in the 450 to 550 range. An Antec True550 would put you at around 55% of it's 530 watt maximum, which is really close to ideal.
Hope this is of some use.

Satellite P500-12D - A problem with the cooling system has been detected

hi there everyone,
I have bought a Satellite P500-12D which was a retail return. When I start it up it runs a couple of mins and then this comes up on the screen:
Warning: A problem with the cooling system has been detected. please turn off the computer immediately and return it for service.
In the toshiba health monitor the cpu is under 50% temp and if it goes much above that the cooling fan comes on and lowers it back down and the fan stops again, I have noticed that only the r/h fan runs to cool the cpu, should both them come on together? Could it be a software problem?
Tthe unit is new without even the plastic off the screen surround or webcam. Any help or even point me in the right direction would be very appreciated, gary

The fact that the pc is a retail return would indicate that there was a fault at day one and the customer returned it. At some point the retailer turned it on and since it appeared to work re-sold it.
This is the cooling/fan report from a P500 produced by pc wizard 2010 - free from cpuid.com. Perhaps a comparison against the faulty laptop will point to the problem
<<< Voltage, Temperature and Fans >>>
> Hardware Monitoring : National LM79
> Voltage CPU : 1.02 V
> +3.3V Voltage : 1.02 V
> +5V Voltage : 0.43 V
> +12V Voltage : 1.02 V
> Chassis Fan : 42187 rpm
> Power/Aux Fan : 21093 rpm
> Processor Temperature : 64 C
> Mainboard Temperature : 16 C
> Hardware Monitoring : ACPI
> Thermal Zone : 48 C
> Processor :
> Intel Mobile Core 2 Duo (Core 1) : 57 C
> Intel Mobile Core 2 Duo (Core 2) : 58 C
> NVIDIA GeForce GT 230M : nVidia Driver
> GPU Temperature : 35 C
> GPU Diode : 35 C
> GPU Fan : 100.0%
> Hard Disk Monitoring : S.M.A.R.T
> Hard Disk TOSHIBA MK5055GSX (Assembly) : 38 C
> Hard Disk TOSHIBA MK5055GSX (Assembly) : 27 C

[GeForce 6] problems overclocking my NX6800GT with newer nvidia drivers

Hiya guys,
JUst wondering if anyone else is having issues oc,ing there 6800gt with the newer nvidia drivers?any driver newer than the 71.25 version causes freezes and corruption and does not matter what speed its at even does it at 360 1050 but at default 350 1000 everything is fine.
BUt oc,ing with the msi 71.25 and below drivers it runs without error at 400 1100 temps are at 52c load 45idle,
Have installed fresh winXP pro,thought it may have been a power problem so i ripped out my 420w thermaltake psu and replaced it with a nice new Enermax noisetaker 485w psu with dual 12v:18a rails still no go,have tried every driver availible only drivers 71.25 and below will oc,all driver up to 76.50 will not,also have tried coolbits,rivatuner,powerstrip etc..and still no go.
Has anyone come accross this?? feel free to share.....
AMD64 3200+ 2200mhz
Gigabyte k8ns pro nforce3 mobo
2x512 kingmax pc3200 memory
Msi nx6800gt 256mb agp
2x80gig westerndigital ide HDs
pioneer 107d dvdwriter
samsung dvdrom
Audigy 1 sound with 5.1 genius sound system
Black thermaltake tsunami dream case
21inch sony trinitron flatdisplay
Enermax noisetakerEG495P-VE dual 12v:18a rails +5v:32a +3.3v:32a 485w PSU

wow - this is my story also... I have been up and down the street with my MSI 6800GTs (in SLi) and they do not OC worth a damn... I am pretty bummed out due to the money, time, blood, sweat, and tears I have shovled into this rig and I only get stock... essentially... I have tried all the OC'ing utilities, different power supplies, volt modding... and I think it's got to be some bios setting or maybe the one piece GPU memory cooler design... the GPU and memory both heating this thing... I don't think it works that well... honestly... I have been around the net, on many forums... and the only peeps who have /any/ luck with OC'ing these MSI 6800GTs are water cooled... anyways... I have spent soooo much time on this and for that reason alone I doubt I will be buying MSI products in the future, but I would still like to find a solution which allows me to push my $900 worth of video cards to ultra speeds. I am really considering going with water cooling... but I really don't want to deal with the hassles of it right now... what I would really like to find or buy are some 6800 Ultras reference design coolers to install on my GTs... I think a lot of this inabillty to OC well is heat related... I know I can get 10mhz more out of my cards when my room is cool.... I have a LOT of air on these cards... and good ventilation... I have my system stats in another post on this forum entitled "nx6800GT OC issues in SLi" or something like that. Good luck man, and I will let you know if I find a solution for this.

How can I use the old Apple TV with new iTunes? It tells me to input a code in iTunes but iTunes no longer has a spot to input this code to allow sync. I can access the iTunes Store fine, just none of my Library

How can I use the old Apple TV with new iTunes? It tells me to input a code in iTunes but iTunes no longer has a spot to input this code to allow sync. I can access the iTunes Store fine, just none of my Library

read this
https://discussions.apple.com/message/20429789#20429789

How to change the Existing alias with new alias name...MAXL SCRIPT

HI Experts
I need to change alias name of the existing member with new alias name.
please send me maxl code to change the alias name .
My thought is
1) Old alias should be replaced with new alias name .
2)There is one account that should be rolled out to another parent..these parents are already exsist
3) I need a MAXL Script to change the new alias name .
please suggest ASAP.
Thanks
USER

John
I heard that we can replace existing alias name with new alias thru MAXL
i.e replace alias name XXXX member with YYYY ;
please correct me if iam wrong ,might be Maxl command is wrong but this is the idea.
Thanks
USER

WiFi no longer working with new Time Capsule-can you help please?

Hi all,
Just received my new Time Capsule (TC). It was a little problematic setting up, but probably due to my now choosing to increase my security from WEP to WPA as the TC set-up assistant suggests. Since then, I have had numerous problems getting my other computers and now my iPhone to connect with WiFi.
The problem is that despite entering all the new settings and WPA passwords for my connection with the TC, the iPhone will either momentarily recognize and go to wifi or simply stay on Edge.
On the former, with wifi active, as soon as I go to iTunes, Safari or check email, it reverts to Edge. On the latter, despite resetting, entering password, or tapping Settings and selecting my wifi connection, it will NOT connect and stays on Edge.
(Now, I'm on Edge! I'm bummed that with new hardware I have new problems that didn't exist before!)
Can someone who had this same problem tell me how they resolved it.
Here's the one clue I have, but would rather not resort to: When I first set up the TC, I had it on WEP with a WDS Network, and everything was working great and FAST! Now that I have increased the security—I will be backing up 3 computers to the TC—my iPhone and other computers seem to have intermittent or no wifi connection as a result.)

Irving Gonzales,
If your computers are 802.11N capable, you might want to try an advanced setup that might help your Time Machine speeds some. I have not personally tested it, so it is just a personal theory at this point.
First, in a mixed environment the 802.11N clients all get slowed down.
First, configure the TC for 802.11N only.
Second, connect the Airport Express via ethernet to the Time Capsule
Third, configure the Airport Express for bridged mode (doesn't give out IP addresses), and for its own wireless network with a different name than the Time Capsule.
Have any 802.11b/g clients like the iPhone join the Airport Express' network.
Thank you,
Nathan C.

TS3899 Cannot send email with new iPad air. Works fine with old iPad and iPhone.

Cannot send email with new iPad air. Works fine with old iPad and iPhone. I have deleted account and reinstalled.

Thanks. I got the problem fixed. Spent time with the Apple folks and was kicked up to a senior advisor. It seems the problem was with my internet provider - Tmie Warner. Remember I could use the old ipad and the iphone to send mail. I checked all the specifics between the three units. It seems that TW is changing over from the RR.com to TWC.com. Since the new ipad air was just set up, it fell under the new TWC mail specifics.

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed?

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed? I am using Firefox Beta for android and I also tried just Firefox.

Please check the Play Store app for any Flash updates and install them if present.

6600GT with new cooler

Similar Messages

Maybe you are looking for