802.11x device drivers in Solaris 10

Can any one point me to a list of 802.11x devices supported by Solaris 10
Thanks
Enzo

http://www.sun.com/bigadmin/hcl/

Similar Messages

  • Compatible USB 802.11x devices?

    Hi, my mac mini is tucked near a TV in a corner behind a wall, and has very poor reception. Ideally, I'd like an antenna on a cable maybe >1 meter long in order to get to an area with much stronger signal. Since this can't be done, I'm looking for a USB wireless card, but I'm not sure if one that is designed for windows will work. I'd rather not fork out ~£30 only to find the NIC is Windows only.
    Are there USB wireless cards that'll work on the mac or are we restricted to airport only?
    Many thanks in advance!
    Mac mini, intel   Mac OS X (10.4.7)  

    In my opinion a better option would be an external ethernet wireless bridge such as the Linksys WET54G.
    This has
    a) an external aerial which should improve reception
    b) is connected to the Mac mini by ethernet cable and therefore could be placed in a better location for better reception, rather than stuck behind the mini.
    It should be noted most USB adapters:
    a) do not work with OS X
    b) those that do rely on drivers which have been known to "break" following OS updates or similar.
    c) people have problems getting them working.
    iFelix

  • Solaris10 : Looking for block device drivers samples

    Hi,
    where can I find complete examples of block device drivers for solaris 10 ? Ramdisk driver for example.
    It's for educationnal purpose.
    Thanks,

    OK, i got the driver now.
    I tried to install it on solaris 10/sparc.
    No problem at compilation, no problem at installation.
    But something goes wrong when trying to mkfs the ramdisk :
    # mkfs -F ufs -o nsect=8,ntrack=8,free=5 /devices/pseudo/toto@0:c,raw 1024
    Can not determine partition size: No such device or address
    # ls -l /devices/pseudo/toto@0:c,raw
    crw------- 1 root sys 98, 0 Jun 14 03:15 /devices/pseudo/toto@0:c,raw
    Any ideas ?

  • Will Solaris 2.7 device drivers work in Solaris 2.6

    I have three systems running Solaris 2.6 for a customer application. My customer has requested a fourth system. The new system has the newer SCSI host adapter AIC-7890. Solaris 2.6 does not recognize the adapter and will not allow me to boot from the installation CD. I downloaded to Solaris 2.7 boot disk and it recognized the hardware. I tried using the Solaris 2.6 CD only to find out that it does not have the driver for the CD.The message I receive is:
    " can't load drivers for pci@0,0/pci9005,f@6/sd@3,0:a.
    can't load filesystem"
    How much trouble would it be to get the 2.7 device drivers and use them in Solaris 2.6? Or would I better off upgrading to Solaris 2.7? I am trying to avoid maintaining multiple versions of the operating system and not have to recertify my applications on the other existing systems.
    Any suggestions would be greatly appreciated.
    Eddie Morris - Lockheed Martin Mission Systems

    * Hi Eddie,
    You may use Solaris 2.7 for the new system and retain Solaris 2.6 on the 3 old systems. There shouldnot be any operational problems if you have a mix of Solaris 2.6 and 2.7 systems. However, if you really do not want to maintain multiple versions of the OS, you may upgrade the Solaris 2.6 systems to Solaris 2.7.
    Thanks

  • I did every step including reinstall intunes to get my IPod touch to sych with intunes and not show up as a camera and nothing works. I even updated the device drivers. Genius bar at apple store told me the ipod was fine, the problem was my intunes. Help

    I did every step including reinstall intunes to get my IPod touch to sych with Itunes but it fail to recognize it as anything other than a camera. It still recognize my Ishuffle as a device. The Genius bar as an Apple store told me the Ipod worked on their Apple PC, my pc is not an apple, I attemped every step to rectify the situation including updating the device drivers. I wonder if I need to eliminate every old residue with the word Apple in it on my computer to get it up and going again. Please help !

    If not this:
    iOS: Wi-Fi or Bluetooth settings grayed out or dim
    One user reported that placing the iPod in the freezer fixed the problem.
    Also heating sometimes works. See:
    Why can't I select my wifi settings?
    A trick that works frequently with iPhones:
    Settings > AirPlane Mode ON, Do Not Disturb ON
    Power down and wait 5-10 minutes
    Power up
    Settings > AirPlane Mode OFF, Do Not Disturb OFF
    If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
    Apple Retail Store - Genius Bar
    Then:
    Does the iOS device connect to other networks? See other networks? If yes that tends to indicate a problem with your network.
    Does the iOS device see the network?
    Any error messages?
    Do other devices now connect?
    Did the iOS device connect before?
    Try the following to rule out a software problem:                
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    .- Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network      
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • Using Solaris 8 drivers under Solaris 10?

    I have a Mylex AcceleRAID 352 SCSI RAID controller card I would like to use under Solaris 10/11. It has drivers for Solaris 8 and is reported to work unofficially under Solaris 9.
    What are the chances this will function reliably under Solaris 10/11? Has the driver format changed appreciably? Can anyone comment on using older drivers in newer versions of Solaris?
    Many thanks for any advice, comments, or tips.
    Regards,
    Andrew

    <i>should I try the big monitor with the 13w3 connector</i>
    Yes, this is the primary output.
    Attach the monitor to the 13W3 output and change the <b>output-device</b> to the integrated video.
    Michael

  • Using transforms and filters without device drivers

    Hello,
    I came across NIMS as a possible solution for some transforms and filtering, possibly even generating test signal data, for a seismic application. I'm in the process of evaluating NIMS for best possible fit for what we need/want to accomplish.
    Basically, we've got some seismic data, and we want to process that data through a series of transforms and filters to denoise and pick the data for seismic analysis. No sense reinventing the wheel if we can adopt and then adapt a third-party library like NIMS into our app.
    We do not necessarily need any device drivers, although I noticed installing NIMS requires them. Hopefully we can opt in or out depending on what's actually required. Can someone help clarify the nature of the driver dependency?
    Anyhow, like I said I am evaluating it for best possible fit in our application, but in the meantime if someone can shed some light on the above concerns, questions, etc, would begreat.
    Thank you...
    Best regards.
    Solved!
    Go to Solution.

    Glad to hear it!
    -Mike
    Applications Engineer
    National Instuments

  • Re: Satellite C855 - How do I install device drivers without WLan connection?

    I had to reset my son's Toshiba C855-1GP yesterday.
    Bought it about a month ago and windows 7 was pre-installed.
    I upgraded to Windows 8 Pro via online download.
    I was able to reinstall Windows 8 via USB, but when I turn it on now, it's completely empty of programmes and applications.
    I realise I need to download Windows 8 device drivers for the model in question (writing this from another laptop), but not sure how to do this as the wireless device is not being recognised and I am being told to connect via ethernet. Is this just a matter of buying a cable and connecting it from laptop to router?
    Will establishing an ethernet connection enable me to download the relevant drivers?
    I can't figure out which Wireless driver to download either, as 4 different options are coming up (is that because I'm searching from a different computer?)
    Could someone list the hardware spec for the C855-1GP here so that I know which drivers to download?
    Thanks in advance, and sorry for all the basic questions!

    Thanks so much for your reply - I actually found an old ethernet cable that was lying around the house and downloaded WLAN driver from Toshiba website - 1st driver didn't work but 2nd one did! Now that I have internet on the computer I will be able to download drivers individually as I need them. Good to know I could have downloaded the driver onto a USB and installed that way - will keep it in mind for the next disaster!! Appreciate the helpful advice.

  • Looking for device drivers for HP Pavilion 23-b012 all in one pc

    where do I find device drivers for my pavilion 23 for windows 7 32bit.

    Hi:
    Your PC is not supported by HP for Windows 7 and Windows 7 32 bit will be particularly harder to find drivers for since OEMs have moved on to furnishing 64 bit operating systems on their PC's.
    I can't get to the support pages to find out what model wireless network card your PC has, but here are the links to some of the drivers you need.
    1. Install the AMD chipset drivers and reboot.  These should install the smbus and usb 3 controllers.
    http://support.amd.com/en-us/download/chipset?os=Windows%207%20-%2032
    2. Install the AMD graphics driver and reboot.
    http://support.amd.com/en-us/download/desktop?os=Windows%207%20-%2032
    3. Install the audio driver and reboot.  Accept the agreement.  DL and install the first driver on the list.
    http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=24&PFid=24&Level=4&Conn=3&DownT...
    4. Ethernet:  DL and install the second driver on the list.
    http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=7&Level=5&Conn=4&DownTy...
    5. Card reader:  DL and install the first driver on the list.
    http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=15&PFid=25&Level=4&Conn=3&DownT...
    If you know what model wireless card that PC has, let me know and I will find the W7 32 bit driver for it.

  • MAX 14.0 broken and database corrupt after installing LV2014 and latest device drivers

    I have LV2012 and 2013 (both 32-bit) installed on my Win8.1 64-bit system and have used them without problem.  I recently went through the agony of installing LV2014 32-bit from Dev Suite 2014 DS2 and the latest device drivers from the August 2014 DVD, and now MAX (v14.0) does not work.  Firstly, it is slow to populate the System information display, secondly when I try to expand a tree I get a MAX Database Connection Error (see attached), and there is no software listed at all.  Thirdly, devices are not listed properly even though appearing in Device Manager (eg. a CAN interface no longer lists CAN0 but does show the device but no configuration, same for USB DAQ devices I(see attached), and I do have CAN 14.0 installed), and there is nothing under Data Neighborhood. 
    Initial attempts to install LV2014 were prevented by the NI mDNS Responder and related services not stopping when required by the installer.  This also affected attempts to repair MAX.
    All 3 versions of LabVIEW run OK, but projects no longer include remote or RIO/FPGA hardware - possibly due to uninstalled support software - but without the software list in MAX I cannot tell what is and isn't installed.
    I have performed a Reset Configuration Data, repaired MAX several times, uninstalled it (any all dependencies), turned of the firewall and virus software, and completely reinstalled LV2012, LV2013, LV2014, and device drivers, but with no change to the problem.  I have now lost 2 whole days and I am getting desperate for a fix.  Surely this cannot be the only case of this in the whole world.
    Mike
    CLD & Alliance Member, UK
    Solved!
    Go to Solution.
    Attachments:
    MAX problems.jpg ‏218 KB
    NI mDNS errors.jpg ‏102 KB
    MAX Devices.jpg ‏83 KB

    Hi Dr.M
    In order to workaround and repair your MAX problems , please see the following article (the Knowledge based article mentionned in the error):
    I know you have been through a couple of these steps , but there may be some related links that could help as well.
    http://digital.ni.com/public.nsf/allkb/B9107A7F281​F9B408625720B0078E5A8?OpenDocument
    As for your installation errors:
    This error happens when a service gets hung up in a "stopping" state that does not allow the installer or uninstaller to remove it.  This can happen with a number of different services, but it has appeared to happen mostly with the Lookout Citadel Server (lkcitadel server) and National Instruments Time Synchronization (lkTimeSync).
    -To resolve the issue, open up the Services application by going to Start»Run and typing "services.msc" without the quotes.  In the window that opens, find the service that the error message references.  It will usually have a status of "Stopping." 
    -Double-click on the service to open the service's properties window as seen below.
    -Try clicking Stop to stop the service.  If this does not stop the service, set the service's type to Manualand restart the computer.  It is safe to set the service to Manual because it will be started manually if it needs to run.  After the restart, the service will not start automatically and you will be able to install or uninstall your software as necessary.
    As for the devices not being visible have you downloaded the NI DAQmx drivers correctly(after installing LabVIEW).
    Regards,
    Mark 
    Applications Engineer Intern
    National Instruments UK and Ireland

  • ITunes 10.3.1.55 on Windows 7 64bit device drivers are not signed

    I have Windows 7 Ultimate and upgraded to iTunes 10.3.1.55.  Now iTunes will not reconize my device. It appears that Apple has incorrectly signed the device drivers and Windows will not install them. Has anyone come up with a solution to this, short of disabling didital driver enforcement?
    Tom

    Perhaps let's first try updating your Apple Software Update.
    Launch Apple Software Update ("Start > All Programs > Apple Software Update"). Does it launch and offer you a newer version of Apple Software Update? If so, choose to install just that update to Apple Software Update. (Deselect any other software offered at the same time.)
    If the ASU update goes through okay, try another iTunes install. Does it go through without the errors this time?

  • Device drivers

    Hi I have an issue with my touchsmart PC following a update a few weeks ago. The PC no longer connects to my wireless network automatically and has been trying do do an update and failing when powering up.  The PC also no longer recognizes devices plugged into the usb port and now it wont recognize the wiresless printer. When trying to reinstall the device drivers It tells me it is unable to access the registration key and wont proceed. Any help gratefully recieved. Thanks

    Hello perksm,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how your desktop computer is not able to connect to the Internet and cannot register new devices or configure them. I would be happy to assist you! To begin, I will need to ask you a few questions:
    What is the Product and Model Number of your desktop computer?
    What version of Windows do you have installed on your computer?
    What model of router are you using?
    Do you have other wireless devices that can connect successfully?
    Is this an on-going, or recent issue?
    Is the BIOS on your computer up to date? If not, you can follow this document on how to Updating the BIOS.
    In the meantime, I recommend following this document on Using Microsoft System Restore (Windows 7). This should help restore your Operating System back to an earlier restore point.
    Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
    Regards  
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Availabili​ty of Windows 7 Beta Device Drivers for some Lenovo Thinkpads

    Good Day
       Lenovo will be posting 10 Windows 7 Beta device drivers* to it's public
    Windows 7 beta webpage before the end of May. The drivers posted will be:
      1)  Lenovo System Interface Driver
    2)  ThinkVantage Active Protection System
    3)  UltraNav Driver with support for single and multi touchpad systems
    4)  UltraNav Utility
    5)  ThinkVantage Power Manager
    6)  ThinkVantage Power Management Driver
    7)  FingerPrint Driver
    8)  Hotkey Features
    9)  ThinkVantage Access Connections ver 5.40
    10) WWAN 
       The drivers will be available at   www.lenovo.com/windows7beta
       These drivers are STRICTLY beta and have NO public support.  Please do not
    call the Lenovo HelpCenter seeking support as they will not assist you.
    Feedback on driver issues via this thread is encouraged and those concerns will
    be send back to the individual device driver development teams. 
      There will be 32 bit and 64 bit versions of some device drivers are available.
      *Drivers are supported on RC Build 7100 and later. The drivers may work on earlier builds
    Terry  Lenovo Win 7 TestLenovo Enterprise System Experts  

    <chuckle> we are all excited to try them
    Message Edited by Darksaber on 05-16-2009 10:28 AM
    x200 7454-CTO; 320GB HD; 4GB; Win 7 64bit - Now on RTM.
    - 2nd SSD with Win 7 Enterprise RTM
    T61p - RTM - Win 7 Enterprise
    S10 4231 for my wife - now on Win 7 Ultimate RTM

  • Mass Storage Device Drivers have been corrupted itunes 7.0.2 cant fix it

    My ipods mass storage device drivers have been corrupted (Device cannot be started Code 10). Itunes 7.0.2 cant fix it. Im not willing to uninstall itunes and reinstall it to fix problem. I have 2 librarys on my hard drive with the guts of 120g of tunes/vids i know i wont lose the data but just dont want to mess with it. Is there any other way to fix the corrupted driver? Itunes 7 is great but they really should have the ipods driver seperate

    I have uninstalled itunes 7.0.2 and installed the default itunes 6 software and ipod software then i updated to 7.0.2 and still same problem. Obviously the corruption is Windows related, but still cant work out the problem

  • Unable to install windows 7 on X60 says "no device drivers found"

    Hi all
    I have working lenevo think pad X60 32bit with windows XP installed on it, first time I was able to succesfuuly installed to windows 7 using clean install,everthing works great.
    Then some how my PC got infected  with virus and not able to boot it always says "recover from windows"  but could not succeded, finally wanted to re install again using windows 7 DVD
    First I set boot order from CD but it always booting from infected image from HD and displays same message.
    I have tried another option by getting into command prompt where I did access to my DVD drive and issued setup.exe
    I went couple of instructions and finally stuck where it is unable to install windows 7 by giving below error
    it says "no device drivers found" on the bottom of window and top of the window it says "where to install windows 7"
    On window I think it will expect partition details but window is empty
    I am not sure why my hard drive is not recognizing, I tried some of the drivers from this site but it could not recognize even if I select via browse
    Any one sees this beviour ? which drivers I shoud install ? in order to see my hard drive
    I still found some of my drives under X:windows\system32 but could not selecting those with windows 7 setup

    you can download pc doc http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-56222 and erase your HDD then install win. 7 this download makes a bootable disc & you can run  diagnostics with this disc
    Thinkpad R61 7733-1GU
    Thinkpad X61T 7762-54U
    Thinkpad X60T 6363-4GU
    Did a member help you today? Thank them with a Kudo!
    If a post answers your question, please mark it as an "Accepted Solution"!
    Regards,
    GMAC

Maybe you are looking for