[875P Neo Series] Not booting

Components : 875 P motherboard. 1.5gb 3200 RAM, Two pairs of 256 and 500 respectively. Two 150gb HHD's set up as Raid for speed.
Changed components to put in a new case to assist in cooling. Jeantech Apollo. Discovered hadn't wired up fans correctly when system kept switching off automatically. Rectified but now when starts up, hear slight HHD activity but nothing else. Fans running. No graphics.
Any ideas. Is there a way of testing components - ie Motherboard and CPU

Check the powerconnectors ( 4-pin cpu and 20pin MoBo ) and try to boot with only 2x256 or 1 x512 RAM and as few other USB and IDE devices as possible and see if i makes any differans.

Similar Messages

[875P Neo Series] USB Flash Drive Boot?

I've got a 875P Neo-FIS2R MB, MS-6758 (v.1.x) with AMI Bios 1.6. Before purchasing a USB Flash drive, I'd like to know whether this MB can boot from it.
Any help appreciated

See the link in my signature. You should be able to.

[875P Neo Series] To Upgrade or not??

I have a 875P neo-LSR 6758, Im trying to decide what I should upgrade too? This is what I have P4 2.6, 160gig/ 512Mb 333mhz memory single dimm, with a spectrum 7f Geforce MX440, I want to use this with a 2O or 24inch monitor in my room as a media center p/c. I want it to be capable to gaming, surfing, some small video editing of Family vids and tv recording once or twice a week ( history channel) and just be a all around very capable computer. Im thinking of going to a 3.2 extreme 478 pin, 2Gb (2dimms) of RAM, add 2 more hard drives probably 250's and a all in wonder xt800 card AGp of course b/c of mother Board. All this will equal to about 900-1000$. Should I put this into this mother board??? I believe everything will work and I can latter switch to a pci compatible board and new processor the transfer everything else over.Will take any info you guys want to dish out. Todd

Quote from: Streifenkarl on 02-December-05, 05:47:18
Two generations? I thought its last generation, I mean the S775 9xx boards are the latest generation, right?
I think he might be right about the Two generations thing.
Next Gen = 975X (Can't Wait!!! )
Current Gen = 945 & 955 (These mobos support Dual Core)
Last Gen = 915 & 925 (True DDR2 came into play w/ these mobos)
Two Gen = 865 & 875 (These boards support DDR400 & 8X AGP + SATA)

[875P Neo Series] trouble shooting assistance

I have a 875p neo with a pentium4 3.2ghz processor...i have a few diff profiles set up for gaming, normal use ect....the system booted up went to my selection screen for profile selection and hung up ...after a few minutes i shut it down and restarted now all i get is all the fans work including my video board ones theD Bracket lights all start as green and none change ....no beeps at all....im suspecting the processor is damaged...i do use a zalman pure copper heat sink for cooling ...other than that im guessing memory or video board...but memory id be supprised both sticks are bad at once and ive tried each seperately...im real supprised this has happened my system for the most part has been trouble free.....im using a gig of 3200 series kingston...a msi video board the 256 meg 5900 model... and a westen digital 80gig hard drive, sony cdrw...any suggestions would be appreciated
thanks in advance...
weez

i would not even try to power up the sys untill the psu is in place,if the cpu failed and needs a warranty replacement i dont think you will get any fuss out of intel,BUT you may have other problems looming that may appear at some time or another,lack of AMPERAGE {not voltage} can have a very NEGATIVE affect on the sys as a whole,if it is a mobo failure you should be ok with that also,it just takes a long time during a RMA process since it usually takes 4 to 6 weeks to complete each,mark it up to a learning experence,the PSU {imo} IS the most important piece of hardware that you or anyone will purchase for a computer !
Quote
does anyone use the dlink lights at all...and is it a reliable troubleshooting tool
,i donot use it but many here do and find it very usefull. also look here https://forum-en.msi.com/index.php?topic=34535.0;all
also the battery can have a bad contact which can cause a no post,also the psu connector pins can become dislodged and push back and cause arching {because of current jumping} that can be harmfull to the pins and sockets.
hope this helps!

[875P Neo Series] problems powering up when sata on ich5r is enabled

Hello, there is a problem on my 875 neo fis2r motherboard.
In the "integrated peripherals"-->"on chip ide" section on the bios (v2.4), when i leave the option "sata keep enabled" to yes, i have problems on system power up.
I switch on my computer and there might be half a minute or more until i here the "beep" on the motherboard and boot from my HD.
Could anybody know what is wrong?
Thanks in advance for your help
Mobo: MSI 875P NEO-FIS2R
CPU: Intel P4 Northwood 3.0Ghz, 800FSB, 512KB L2 Cache
RAM: 1x512mb kingston PC3200 CL2.5
HDD: 1x160Gb Maxtor 8mb 7,200RPM S-ATA
Optical: 1x Plextor 716a, 1x Plexwriter Premium, 1xPlextor 116A
Floppy: Mitsumi MTM43W 1.44MB 3.5in
Display: ATI Radeon 9800XT 256mb
Sound: Soundmax digital audio
Case: ANTEC Performance Plus Series PlusView1000AMG
Power : Antec TruePower 550
Fans: 4x 80mm
Display : LG Flatron F700P

Hey Grigo,
For that set up, I would recommend trying the following settings:
On Chip Operate Mode: Native
ATA Configuration: S-ATA Only
SATA Keep enabled : Yes
PATA Keep enabled : Yes
That's how I set up my old 875P without trouble when I installed a pair of drives in RAID 0. In your sig I don't see two drives, so I'm not sure what else to provide. (whether you are building a new comp or upgrading to RAID 0 etc)
For further reference, have a look at Vango's guide to RAID setup here: https://forum-en.msi.com/index.php?topic=38845.0

[875P Neo Series] Dead mobo or dying ??

-Motherboard type and model (MSI 875P NEO-FISR)
-Bios type and revision (Latest)
-CPU type and model (3,2 P4 HT)
-Memory name, model and quantity (2 x Kingston KVR400X72C3A/512)
-Video card name and model plus drivers and version (ATI AX800 PRO)
-Power Supply name, model and the amp rating for the +3.3V, +5V and +12V lines plus any limitation on the +3.3/+5V combined watts. This information can be found on a sticker on the side of the supply. (Q-TEQ ATX 350, 3.3V = 20A, 5V = 0,5A + 35A, 12V = 0,5A + 17A, 5VSB = 2A)
-Hard Drives: (2 X 200 GB WD)
-Optical Drives: Manufacturer and type and which IDE ports they are located on: (NONE)
-Operating system and service pack level: XP SP2
the short version:
the mobo went unstable and started hanging when playing 3D aplications like medal of honour, wolfenstein ET and others...
then the hangs started occuring more rapidly, and now the pc starts VERY randomly
i often have to try to start it 10-15 times before it starts....
the chipset and cpu fan starts, the hd drives starts and the ROM starts, but no signal to vga card.
i have tried to reset chmos, changed vga card, stripped the pc, but nothing works..
and: it has worked for over 7 months without any probs...
is it possible a virus did this ??
can anybody help ???
please ???

350 watts is far to low for your system............
Min AMPS on +12V rail for your system should 24AMPS
Q-Tec do not have good rep and have caused at lot of problems
Try a brand name 450+Watt PSU Enermax or Antec or Hiper series (These I have personally tested)

875P Neo FIS2R DRAMM / Boot Problems

After having significant difficulties with my new machine
I thought it may be helpful to others to know how I fixed the Mother Board problems. I have the following configuration:
875P Neo-FISR
P4 3.02 GHz 478P 800fsb
Two Geil PC 3200 400MHz 500mb DDR’s at positions 1 & 3
( CAS 2 6-3-3 1T; 2.6-2.9 V)
Two Seagate 120 Gb 7200rpm SATA drives on Promise Raid 0
Generic Cd Reader
Pioneer DVD Writer DVRA05
ATI 9700 Pro
Aquarius Liquid Cooler
Enermax Fan Monitor
( Addictions are bad )
Open all the boxes and put everything together. Boots up once and then starts active unstable.
Clear the CMOS and then it fails to post at all.
No monitor at all.
Looking at this web site I thought that putting the Aquarius Fan on the SFAN 1 slot may not be playing with CoreCell Chip well. Switched to the Enermax and it boots. Remains very unstable. Reading an email here I changed the DDR voltage to 2.7. System stable but I can’t get the Promise RAID to engage.
Looked at another email ( Thanks Mr. K. Keenan)
and set the BIOS as follows:
Frequency / Voltage Control:
CPU Ratio Selection: Locked
Dram Frequency : AUTO
Spread Spectrum : DISABLED
Adj. CPU BUS Clock: 230
DDR Clock: 460
Adj. AGP/PCI Clock: 67.1/33.50
CPU Vcore Adjust: YES
CPU Vcore: 1.5750V
DDR Power Voltage: 2.70 ( KK suggested 2.65)
AGP Power Voltage : 1.75
Everything stabilized.
Start adjusting the Promise RAID settings (following M. Johnson’s advice)
as follows in the BIOS:
ON CHIP IDE Configuration
ON Chip ATA Operate Mode: Native Mode
ATA Configuration : S-ATA Only
P-ATA Keep Enabled : YES
P-ATA Channel Select : BOTH
S-ATA Ports Definition: PO-1st/P1-2nd
Configure S-ATA as Raid : YES
Back to
INTEGRATED PHERIPHERALS
ONBOARD Promise IDE: as RAID
Run Windows 2000 prof and it finds the array but can’t format ( ???)
Tried formating with Millenium Boot disk ( Bad move).
Windows ME won’t let Win 2000 boot.
Clear CMOS and then the system dies.
Spent days trying to get at least the monitor to fire with no luck.
Reread web site and picked up on the Low Latency Memory issues noted
in a note ( Thanks Mr. K. Keenan again). Put in some Kingston cas2.5
333 DDR’s at 1 & 3 positions.
Fires up immediately.
Windows 2000 boots and loads. Totally stable.
Never to be one that leaves well enough alone…
Set the BIOS under
ADVANCED CHIP FEATURES as follows:
Under dram Timing Setting:
Configure DRAM Timing by SPD : Disabled
Cas Latency: 2
RAS # Precharge 3
RAS # to CAS# Delay: 3
Precharge Delay: 6
Burst Length : 8
AGP Aperture Size: 128 MB
Shut down and replaced the 1GB ( 2 x 500) Geil DDR 400’s.
Rock stable and faster.
Evidently when you clear the CMOS, the board resets
the DDR Power Voltage to 2.50 which is too low for
some of the faster DDR SDRAM’s. Unless you put
slower chips in you can’t adjust the bios to a higher voltage.
I would love to know why MSI did that.
Hope this trail helps somebody else.
Best RBC

Quote
Originally posted by Undergrid
Quote
Evidently when you clear the CMOS, the board resets
the DDR Power Voltage to 2.50 which is too low for
some of the faster DDR SDRAM’s. Unless you put
slower chips in you can’t adjust the bios to a higher voltage.
I would love to know why MSI did that.
Simply, when you use the jumpers to reset the BIOS all the settings, including the voltages, get reset to the default. The default power setting for RAM is 2.5v, and I would assume that its difficult to find RAM that doesn't run at that voltage at least well enough to get into the BIOS. What use would the jumper reset be if it only selectivly reset settings?
Hi all,
The system will reset the performance to Slow and the DDR ram timing to default by just 4 unsuccessful boot up.
Meaning just press reset button for about 4 times and the system will boot with the default setting for the performance and RAM Timing.
So I do not need to do jumper reseting or open the CPU casing.
Cheers.

[875P Neo Series] 875P NEO FIS2R - Bootup delay with disk attached to Promise RAID

Hi,
I have a problem with my 875P NEO FIS2R mobo. I just added a 400GB SATA RAID-0 array to the Promise controller and now I get a 50 second bootup delay after the BIOS has run through everything and beeped and before the first WinXP splash screen.
I boot up from a 160GB SATA RAID-0 array on the intel ICH5R controller. Both arrays work fine from within Windows. I have two DVD drives on the ICH5R PATA connection but nothing else on the Promise.
If I disable the Promise controller in BIOS the delay goes away.
I have tried disabling SMART, turning off the quick-boot option with no effect.
When I first installed my system I tested performance with booting from a single SATA drive on ICH5R vs Promise and I noticed the same issue, but didn't care then because I only needed one disk so I just kept Promise disabled in BIOS.
Any ideas how I can get around this?
Regards,
Jonathan

Sorry I have been a away for a few days.
Details requested...
Quote from: redeyedog on 21-June-05, 05:50:27
If the Promise controller was out of the picture (Disabled), and you have the SCSI adaptor and its devices setup:
1. What is the adaptor's SCSI ID?
7
Quote
2. List devices, position in the chain and their corresponding SCSI ID's.
#7 Adaptec 2930CU card
#4 Nikon Coolscan LS30 scanner
#3 Umax Astra 1220S scanner
#5 Iomega ZIP 100 drive
Quote
3. What type of terminination are you using?
Adaptec card has auto-termination.
ZIP drive has a termination connector attached.
Quote
4. Are the devices in the chain functioning properly?
Yes.
Quote
I agree that your problem is your SCSI controller. There may not be anything actually wrong with it. The 2930 was an agressive controller card and its BIOS simply may not coexist with your motherboard's BIOS optimally. Even with the BIOS disabled, it may be competing with the motherboard's request for handlers.
You may want to check to see if there is a BIOS update on Adaptec's website. Adaptec usually released 1 or 2 updates for each SCSI generation they produced. It may or may not help but we need to make sure you have the latest BIOS released.
Unfortunately, this card cannot be reflashed.
Quote
At any rate, I think you have found the component which is responsible for the delay. I'm willing to assist in diagnosing the issue but I need you to provide the specific information I'm requesting.
Also, try to do a CTRL-Pause to catch exactly what the BIOS version is and any other information which is showing up with the BIOS disabled. The SCSI adaptor BIOS, in fact, should not be enabled in your SCSI configuration as you have described thus far.
Adaptec AHA 2930CU SCSI BIOS v1.34.1.
There seems to be a difference between BIOS and host adapter BIOS. You always get the BIOS screen, but you can disable the host adapter BIOS if it is not required.
I am pretty sure it is not the SCSI chain that is wonr because the pause happens with nothing connected to the card.
Jonathan

875P NEO-FIS2R no boot with memory problems

I just got a NEO FIS2R board, a P4 2.6C, and two 512MB sticks of OCZ PC3200 Premier DDR. I installed the board and connected only my hard drive, video card (GeForce4 Ti4200), both sticks of memory, and CPU (on a 300W PSU). At first, the board would eventually make it to the "booting OS" stage, after spending a little time on "initializing video" (normal) and "assigning ISA" or something like that (don't know what that is, since the board has no ISA slot). Unfortunately, although my monitor's light changed from yellow to green, meaning it was getting a signal, the screen remained blank. I gave it a few minutes and finally turned off the computer. After reseating the video card and memory and disconnecting the hard drive, the same problem occurred. Finally, I took out one of the sticks. After this, the computer hung on that ISA thing for about ten seconds, and then went back to "detecting memory" and gave a 2-1 error beep. I switched between the two OCZ sticks and also two sticks slow generic PC2100 memory that I had in my old computer and I know work fine. Eventually the computer stopped pausing at the ISA stage and went to the memory detection after only a second or so. Since the video was obviously acting strange, I disconnected the video card so the computer contained only CPU and memory. The bootup sequence was the same, except that in place of the single beep during video intialization, it gave me a 2-8 error code. Finally, I took the board out of my case and laid it flat on the wooden table and tried again. Still no boot. I also cleared CMOS several times throughout this procedure, so that shouldn't be the problem.
Can anyone figure out what's going on here? It's especially confusing to me that the computer booted all the way (sans video) at first, then started having memory problems, and that the system passes the initial memory test but then goes back to it after that ISA thing (this is all according to the D-Bracket).

Quote
On the compatability list, it says
"Kingston KVR400X64C25/512
W942508BH-5 (Winbond)"
Since the memory I am looking at is CL2, does that mean it might not be compatible after all?
If you're wondering whether the Kingston HyperX RAM you're looking at is the same as the Kingston RAM you've found on the compatibililty list, the answer is NO. The RAM from the list that you're referring to has a model number that starts with "KVR", which stands for "Kingston Value RAM". HyperX RAM has model numbers that start with the letters "KHX".
You might also note that there is no listing for any of the HyperX stuff on that compatibility chart. However, I have seen posts from several people on this forum who seem to be using HyperX RAM with no problem. I suspect that MSI hasn't updated that list in awhile, because there are no listings for many of the newer PC 3500, 3700, and 4000 RAM models.
I personally went 512mb (2x256) of OCZ PC3200EL DDR RAM, it is listed as 'OCZ (PN- OCZ400256EL ) PN- OCZ400256EL' on the compatibility chart. I had plenty of problems trying to run a set of Corsair TwinX 3200PCT ver. 1.2 on my 875P NEO board, and I settled them by switching over to the OCZ RAM only because it was listed. While it wasn't my first choice I'm pretty happy with it because so far it's been running stable at CAS 2,2,3,6, with the voltage at 2.65.

[875P Neo Series] MSI 875P Neo-FISR adn ECC registered DIMMS

I have purchased the MSI 875P Neo-FISR (PCB 2.0) and installed a 512MB DDR333, PC2700, CL2.5, ECC registered dimm (HYS72D64300GBR-6-C) but the system won't boot up. I have a Intel Pentium 4 3 GHZ CPU, 512K cache, 800 MHZ bus installed. When I install a 512MB PC2100 unregistered the system works OK, but not with the registered ECC registered DIMM. In the manual it is quoted as saying it supports this type of memory. I have updated the BIOS to the latest version from the MSI website. Any ideas ????

I have currently have
P4 3 GHZ 800 MHZ bus on MSI 875P Neo-FISR, 2x512MB PC2100 RAM (currently working OK)
2 x seagate 250 GB SATA drives in RAID 0 ccombination
Sony 8 x DVD writer
32MB GeForce GTS AGP graphics card
Matrox RT.x100 Extreme Pro video editing card
Craetive sounblaster live 5.1
but would like to add the 2x 512MB PC2700 registered ECC dimms I just bought if at all possible !!!!!!!!!!!!!!!!!!!
damn manual giving me incorrect information !!!!!

875P Neo FIS2R-Slow boot with Raid on Intel + Raid on Promise

Hello all.
Here is the configuration I'm trying to set up (and almost did)
SI 875P Neo FIS2R,MS-6758 BIOS v2.4
P4 2.6 GHz HT
500W 6fan total
2x1G Kit DDR 400
2x74 G WD Raptor Raid0 (Intel S1-2) Win XP inst
2x36 G WD Raptor Raid0 (Promise S3-4)
GeCube X1600Pro
DVD-RW (IDE 2 )
Win XP SP2 (All latest updates installed)
I followed the instructions as they are listed in the sticky (great job btw) and configured the 2 SATA 74G WD Raptor on Intel Raid controller(serial1&2) as Raid0 and install WindowsXP Prof sp 2 on it.
Then I configured the 2 SATA 36G WD Raptor on Promise controller(serial3&4) as Raid0 and added this Raid to the existing WindowsXP installation.
This set up is working very good once I'm logged into Windows with no problems at all.
The glitch is that I need 3 min waiting time till I see the windows loading logo.
I have all the latest drivers installed also IAA and INFs and my bios is as the default values except the changes mentioned in the sticky
Onboard Promise IDE - as Raid
ON-Chip IDE Configuration:
Native Mode
SATA Only
Keep SATA Active - Yes
Keep PATA Active - Yes
PATA Channel selection - Both
Configure SATA as Raid - Yes
I did the Win XP installation twice till now, taking care to install INFs and drivers in the right order but the result is the same...3-5 mins till I have a fully operational windows environment and after that all is running like a dream.
Now, I've searched in the forum and saw that many more people have the same problem but never read the solution to it, so if someone has ever found the way to solve this or has the same configuration please tell me how he did it. Even if someone knows that it can't be solved just drop me a line telling me so. Altough the system is running smoothly I find the 3 min waiting time unacceptable and frustrating. I've run out of ideas so please help me.
Thanks in advance

Hello Blazer and thank you for replying.
Answering one at a time...
are both raid arrays setup with the same stripe size?--> Yes Both arrays are configured at 16k stripes
do you see both the intel and the promise bios setup screens?-->Yes both screens (Intel(R) RAID... and Fast Built (tm) ...)appear almost instantly after MSI's logo screen showing my Raid arrays in Normal status. The delay starts after the Promise's screen till the Windows Loading logo screen.
how is the raid bootable drive identified in the boot from menu?-->
Boot Device Priority:
1st BBS-0 (Raid): Intel <name> (---> this is the OS drive on Intel controller)
2nd Disabled
3rd Disabled
Try other boot devices NO
I have also the option to select the the Drive on Promise which shows as BBS-1 (Raid) FT 378 Ary 1 but I have left it out cause it doesn't have the OS on it.
is the OS drive labeled as C: and seen as 200GB drive [as one] from the four drive array]--> No as it shouldn't cause these are two different Raid Arrays. The first Raid on Intel's controller with the 2x74G WD Disks indeed shows as one C: 137 G and has the OS on it. The second on Promise controller with 2x36G WD Disks also shows as one D: 70G.These are two separate Arrays with 2 disks each and they show as indented.
is network boot enabled causing a delayed boot?--> I don't quit understand what you mean. In case you mean what happens if I unplug the 2 disks from the promise controller then yes if I do that the system boots fast in the Windows even if I leave the Bios setting "configure promise as raid"!!!
My problem is similar with this post: https://forum-en.msi.com/index.php?topic=69994.0
other posts that have reported the same trouble:
https://forum-en.msi.com/index.php?topic=94944.msg683258#msg683258
https://forum-en.msi.com/index.php?topic=81901.0
https://forum-en.msi.com/index.php?topic=66662.0
https://forum-en.msi.com/index.php?topic=98005.0 ---> I wish it was that simple, I did it as with all other drivers
I hope that info helps you helping me.

MSI 875P Neo-FIS2R support booting from USB devices?

I am building a super computer using the MSI 875P Neo-FIS2R. I would like to either get a USB pen drive, or an external Floppy Disk Drive in place of an internal Floppy Disk Drive.
Does anyone know if this board supports booting from a USB device?

I ordered my board as well, however, they were out of stock and it may be as long as 2 weeks before they get more in. If you don't mind me asking, where did you get yours from? I am VERY much excited about getting this board as I only await the MB and CPU. What all are you putting in yours??
Mine:
MB- Obvious
CPU- 2.4 800Mhz
RAM- 2 sticks, 256 PC 3200 XMS Corsair using dual channel, at first I think I will use the 512 pc3200 I already have though.
HDD- 80GIG W/D 7200 RPM ( May get another to run RAID 0)
VGU- Chaintech TI4200 at 8x w/ 128 DDR
CD#1- 52x cd rom
CD#2- dvd 16x, cdr 48 cdrw24 cdrom 48
500W raidmax Pwr Sup
Koolcases Panther case w/ window and 3 80MM/ 1 60MM fans
For now I will even use the old 3.5 A drive. Just in case.
Red light internaly
Digidoc 5 for thermal monitoring on:
1.cpu 2.ram 3.VGU 4.case 5.HDD 6.other ram 7.chipset 8.dvd for curiousity sake. just curious of the temps they produce. but always able to move it to a more vital area if the need arises.
Will be upgrading to liquid cooling in the future, that way when I am deployed the temps stay in the blue. (HOPEFULLY)

BIOS 1.8 for 875P NEO Series

Just curious if anyone has downloaded and successfully flashed their 875P NEO boards to the current BIOS version of 1.8. If so, is your system stable?
Is another BIOS update just around the corner for the 875P or is the 1.8 the latest and greatest BIOS update?
Thanks for any info,

Quote
... what did they correct in the 1.93 Beta?
As advised:
875P Neo MS-6758 BIOS V1.9 Beta 3 (1.93) dated 2003/10/02
This BIOS fixes the following problems of the previous version:
- update microcodes,
- modify HT support,
- Prescott support,
- fixed ICH5 SATA HDD incompatibilities issue,
- remove chinese language support
The promised DOT option still isn't available in BIOS setup!
Note some of the changes from the previous 1.82 Beta were not put in the 1.80 Release ... so which new fixes go in the final release (and when) is still uncertain.

P35 Neo does not boot

Hi,
I have just bought a P35 neo F and a Code 2 Duo E6550 processor.
When I switch the power on, the cpu fan starts and stop and then start again which looks OK for this motherboard - My problem is that the system does not boot after this - I have tried different combinations (with or without memory, with or without hard drive, with or without graphic card, I have tried 2 different graphic cards, 2 different power supply... no result - Could someone help me ?
My config :
MB P35 Neo F
Proc Intel core 2 duo E6550
Power supply Enermax extreme power 500W
Graphic card Asus EN 8600 GTS
Thanks

Quote from: gatebill on 25-January-08, 22:06:15
I've tried a Kingston PC2 6400 CL5 - the system still do not boot up - I can see the keybord blinking at the beginning of the boot process but the screen noes not receive any signal - I get a bip after about 20 sec and another one again after 20 sec.
The processor or the mother board must be faulty...but how to know which ?
MSI P35 Neo2-FIR (bios v1.5)
Intel E2180
Tuniq Tower 120
2 x 1GB Ballistix PC2-8500
XFX GeForce 8600GT
Maxtor 80GB
Seagate 250 GB
Advance 550 watt PSU
I just finished building this rig, and had exactly the same "no boot" issue using Ballistix RAM. The board powered up, then it did the auto shutdown thing which is normal, and then it started up for real, the diagnostic LEDs on the mobo light up, the CPU fan spins, I get a single beep but then just a blank screen, no POST screen, can't enter the BIOS
I tried a minimal build outside the case using just the graphics card, monitor, keyboard, and a single stick of Ballistix RAM in four different slots, re-setting the CMOS at each attempt, But still no POST
I was advised the Ballistix may be the problem as they're rated at 2.2v and the MSI board sets 1.8v until you change the voltages in BIOS, so I ordered 2 sticks Kingston Value RAM 667MHz rated at 1.8v, Inserted a single stick then powered up, but still no POST, Inserted the second stick and the board fired up! I needed both sticks inserted to boot, glad I ordered 2 sticks of Kingston instead of one, I'm keeping them as a backup if the Ballistix fail. Inserted the Ballistix and they're running fine @ 1160 MHz CAS 5: 5: 5: 15: 2T 2.3v

Pt880 Neo will not boot. Help please

Here is my setup. I just picked up a brand new msi pt880 neo series and a p4. 2.8 fsb800/1mbcache.
I was current using a ati 9800 pro and crucial 512 pc3200 ram. i installed two maxtor 160g hd and i was going to run raid in a pci slot raid controller. so far i know the ram works and the video card and the one of the hd. My power supply supports up to 400watts. I have a btc dvd burner, floppy and a liteon dvd rom. im also running 4 fans.
My problem is that when i turn it on, it powers up but nothing else works. On the D-bracket 2 i get 4 red lights lite up and nothing else.
Im stuck and not sure what to do now? Is it my mb or chip or a combination of things? Thank you very much for your time.

Heya,-
Sounds interesting enough to me aswell... I had the same problems with my Mobo too... But it turned out to be the CPU. Intel has release some 'C' versions of that 2.8GHz CPU, which might be some scaled-down Extreme Edition CPU's or even a down-graded Prescott CPU.
So what I needed for my mobo to get it work was:
- Updated BIOS version
- Another CPU (working) to get the new BIOS version on my mobo...
The shop that helped me, gave me some information from Intel. You can check your exact type of CPU in their website... They gave me the link to the Intel P4 CPU Specification Update. And in that document on page 17 I found out that my CPU with package ID: SL6Z5 is in fact a down-graded Extreme Edition CPU, and should have been sold as a tray-CPU, and not as a boxed CPU... DAMN INTEL!... But anyway, they gave me a headache and some nights of incredible sleeplessness...
Just for your information... This is how I found out that it was my CPU causing all this problem:
- Assemble the system with only mainboard and PSU (no memory, no vga, no keyboard)
- Connect the CPU fan to see if the system will start running
- Turn-on the system and see if the CPU fan will keep running
- Shut down the system
- Insert the CPU
- Turn-on the system again... If it fails on your CPU, it should shutdown after 5 seconds...
> To find out if it's related to any of your other peripherals, insert all the things step by step (first memory, then vga, etc...) and see if your system will fail on any of these peripherals.
It just might turn out to be a harddisk that's drawing too much current from your power-supply....
ANyway, just to share some thoughts! Good luck!

[875P Neo Series] Not booting

Similar Messages

Maybe you are looking for