915P Neo2 PE and stupid beeps

hi everybody, sorry for english,
i've a new mobo - 915P neo2 PE
2.8GHz Intel P4(775)
2x256MB DDR2 Apacer (533MHz) in dual channel mode
ASUS AX600XT
500W Mercury Silent PS
after start i get 4 short beeps everytime i start my comp.
if i disconnect one of my usb devices i get just 3 beeps
if 2 i get 2 beeps etc.
if i disable usb controller in bios - no beeps
but it's not everything - i cannot install liveupdate, becouse by initializing of liveupdate my comp crash, also i cannot install sp2 for wxp, becouse it after next restart crash
i manually updated BIOS to 1.5, but no result.
i put DDR2 in normal mode - the same
i put DDR2 to other mobo - everything OK
i changed my VGA - the same
i changed my power supply for one with 24 pins - the same
i changed my CPU - the same
i changed mobo for other 915P neo2 PE - the same
no idea
pls help me, i'm short of brain

add one> those aren't classical beeps, one is high tone and three are low, i don't know what does it means
add two>there's no chance install wxp without sp1 on this chipset, if i install sp2 or live update utility it will crash by boot periodicaly

Similar Messages

915P Neo2 Platinum (V1.0B) and SATA setup HELP !!

Hi,
Can any one help me with the BIOS settings for my SATA HDD on an 915P Neo2 Platinum motherboard ?
Configuration:
- Antec Sonata II 450 Watt
- Intel Pentium 4 630, Socket 775
- Corsair ValueSelect DDR2 SDRAM, 1 GB, PC4300, 533 MHz
- 915P Neo2 Platinum (V1.0B)
- 2x NEC ND-4550 16 connected to EDI 1
- 1x Maxtor DiamondMax Plus 10 250 GB, 7.200 rpm, 16 MB, SATA/150 connected to SATA_1
I have tested with the following settings:
1)
   ATA/IDE Configuration [Enhanced]
   Configure SATA as [IDE]
Result:
   Can't format with Windows Setup CD (sp2)
   If it formatted with 3rd party utils, then performance of the system is very poor.
Thanks in advance !

Hi, I suggest you to set the ATA/IDE config as Legacy and check that all your HDDs are detected, if not all, at least your HDD and optical drive. Then continue with the installation. After WinXP installation settled down, then go back to the BIOS and switch to Enhanced again, and then continue boot up to windows and install Intel INF.

A few bios problems with my 915p Neo2 platinum board

I'm wondering af anyone here can help me.
I just got a new system and a friend of mine helped set up the bios for me, afterwards he failed to tell me how he had configured the bios (my first big mistake).
Since the buidling of the system there have been 3 short beeps at the beginning of startup. I was told that it was a warning system of some sort and when i looked it up, the informations pointed towards a problem with the RAM.
I ran memtest86 and it found no problems with the RAM, so i contacted the site i bought the parts from and they suggested i reset the bios.
I did so and the beeps remained, but my DVD and DVD-writer drives arent being detected anymore.
I took my PC around to another friends house with only his keyboard and monitor connected. The beeping had stopped before we changed anything. Bringing it back around to my house resulted in the beeping returning.
From this i gathered that the only things different may have been his power source and the peripherals i have attached to the back of the case. (speakers, printer, kb/m, etc)
Going by the manual map, my 2 HDDs are connected as slave/master in IDE port 1 and my two DVD drives are connected to the yellow IDE port that is closest to IDE port 1 (it's either IDE 2 or 3, the map isnt too clear on which is which).
Long story short, can anyone help me in identifying the source of the beeps and their meaning, an optimum setup for my bios and how to get my DVD drives to work.
Thanks in advance to anyone who can help me. I'm fairly new to building computers and my friends are the type to suddenly become unavailable as soon as a problem arises.
edit: just noticed i missed the spec description part menitoned in the rules.
MSI s775 915P-Neo2-Platinum
Version 1.4 of bios
Pentium 4 540 LGA775 3.2GHz
Corsair VS 1GB DDR2 240 pin RAM
256 MSI PCI-express GF6800GT, latest drivers
600W 3XS-EzCool PPFC
Western digital WDC WD1600JB-00EVA0 (160GB) (master)
Seagate U series 5 HDD ST340823A (40GB) (slave) Both on IDE slot 1
Liteon DVD-ROM (spec unavailable)
MSI 4x DVD-RW +/- (part no: G57-CB00243, this is all i could find on this part form the box)
Sound Blaster Audigy
Windows XP SP2
second attempt at clearing up the garbled mess from above.
Motherboard is making 3 short beeps on startup. Indication of a problem with memory. I've established that it's something external that causing the beeps as the memory has checked out fine with memtest86. Hence i will be checking all the attached devices.
I was guided to reset the bios in an attempt to clear up this problem above. Doing so has resulted in my bios being unable to detect my DVD drives.
My DVD-drives are connected to IDE port 2/3 (manual is unclear on which is which).
Everything was in working order (with the exception of the beeping) before the bios was reset but due to my lack of knowledge/involvement with the original configuration of the bios, i'm at a loss as to how to fix it.
If anyone could recommend me any updates for the bios, or could advise me on how to configure my bios accordingly to the parts i have i would be most appreciative. Also, if osmeone would be abel to shed some light on the beeping issue i would be thankful also.

Quote
Originally posted by Danny
The board uses a Via raid controller for the IDE 2 and 3 channels, and you do have that enabled.
Under SATA devices configuration you should select Enhanced instead of compatible. But this should effect your problem.
I see there is a 1.5 bios released that mentions the via controller
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=601&kind=1
Maybe someone with this board will pitch in and help.
I saw this and was wondering if i should install it. It would be the equivelent of resetting the bios again wouldnt it? So it wouldnt be that much of a step back from where i am at the moment and it might be able to sort my IDE problems.

915P Neo2 Platinum problems

I'm hoping someone will be able to help me as I've been tweaking bios settings for 3 days and not managed to get anywhere with this.
I've have the following:
1x 915p Neo2 Platinum Mboard
1x Sapphire x600 235MB Graphics
1x Corsair PC2-4200 512 MB DDR2
1x 40GB Western Digital IDE drive
1x 30GB Western Digital IDE drive
When I first switched it all on, the board powered up but I got no display and no beeps. After pulling out all wires and adding the minimum of devices I got it to start up properly and got into bios. Eventually, after tweaking some settings and then systematically adding each device in turn I got everything connected whilst maintaining stability so it would still boot up.
Next problem I has was that it wouldn't boot from a floppy. It kept giving me "Disk I/O error". I tried several different floppy disks - same problem. I changed the floppy cable and still got the same error. I then bought a new floppy drive and tried that but still got the same problem. Decided to carry on and install XP incase floppy started to work later.
When installing, I pressed F6 to load RAID drivers. I selected the IDE RAID driver, it chugged away and carried on loading setup. My 2 IDE drives were successfully identified and I selected the installation drive and formatted it (tried quick and full format), after it had done this, it then tried to load the RAID driver again from the disk. At this point, the driver disk is still in the floppy drive, but it then says that it can not load the file from the disk and to try another. Again I tried several disks all of which gave the same problem.
I've searched this forum to help me with my earlier issues and found answers but couldn't find any info on this one. Can anyone help? I'm starting to think that my mboard has a poorly floppy controller. Also, I've got completly confused about the RAID setup, I currently have both my drives, 1 as master and 1 as slave, in IDE2 and have not touched the RAID BOIS setup - does this mean I will still be able to use these as 2 different drives? Eventaull I will add SATA RAID.

Quote
Originally posted by Del UK
Hi Masjj,
Could list some details of the PSU you using please, as this would help. Please see sig below as a guide.
Confirm please:
You can boot and format, then when install happens, failure????
Del
My spec is as follows:
No OS yet
- tried Win XP (blue screen after RAID driver load)
- trie Win XP with SP1a ("can not load viaraid.sys" error after disk format)
MSI 915P Neo2 Platinum (MS-7028 Ver 10A)
BIOS - Shows "915P/G NEO2 A7028IMS V1.0 05/27/04" on first screen, in BIOS setup screen shows v02.56
Intel P4 3.0GHz PRESCOTT, 1MB L2-Cache, 800MHz FSB
Sapphire X600 256MB + 19" TFT
Soundblaster 5.1 Live card with LiveDrive
Western Digital 30GB IDE (Master)
Western Digital 40GB IDE (Slave)
Pioneer DVR-105 DVD/RW Burner
DVD-ROM
WD 800JB+CD-RW
1* Corsair Value 512MB PC4200 DDR2 Ram
PSU - eTech 460 +3.3v-28A +5v-30A +12V-30A
I cannot boot from Floppy, can boot from CD. When I try to install WinXP with SP1a, I hit F6 to load RAID drivers, choose driver from list. Setup then detects HDDs, I format install drive, then it tries to load RAID driver again from disk and gives a fail message of "unable to load VIAMRAID.SYS" and will not continue. If I try to install without RAID drivers, it says that there is no storage device connected.

915P Neo2 Platinum Hard Drive/Optical Drive Configuration

My main drive is the 120Gb SATA drive listed below but I'd like to utilise a 160Gb PATA h/d that I used to use for backups on my previous system.
I have the SATA drive configured as my boot drive. ATM, my DVD drives are connected to IDE1 as I have a recovery CD which needs to be booted should I need to use my backups.
I've been tinkering with this system and would prefer to have the parallel IDE drive permanently connected to IDE1 but still boot from the SATA drive. To this end, if I connect my DVD drives (configured as master & slave) on a single IDE cable to IDE2 and boot, they aren't recognized as bootable devices when I hit F11 after POST. However, when Windows boots they do appear. With this configuration I can't restore data because I need to boot from a recovery CD-ROM.
Is it possible to have optical drives connected to one of the RAID IDE connectors and make them bootable?
If not, and since I do have 2 drives, I assume someone will suggest going down the RAID route. Can RAID1 be configured across 2 hard drives if I have 1 x SATA and 1 x PATA?
TIA.
915P Neo2 Platinum PCI-E (MS-7028) motherboard
BIOS v1.6
Pentium 4 550 3.4GHz 'Prescott' processor
Crucial DDR2 PC2-4200 512Mb RAM
Asus Extreme GeForce PCX6600 GT 128MB (PCI-E) graphics
Maxtor DiamondMax +9 7200RPM SATA 120GB h/d
Floppy drive
Thermaltake 480W ATX PSU Xaser Silent Edition
Thermaltake Tsunami Aluminium Case
LiteOn DVD-ROM
LiteOn Dual Layer 16x DVD±RW ReWriter
Windows XP Pro SP2

Quote from: NovJoe on 05-April-05, 21:25:01
To what I know, it is not possible to get Optical drives to work on IDE 2 and 3 since they are mainly for RAIDs and HDDs.
Keep the Optical drives to IDE 1 and the IDE HDD to IDE 2.
Thanks for your quick reply.
I've tried that - get the same problem with boot devices in that the h/d on IDE2 won't boot. (It holds a copy of my C partition.)

915P Neo2 - Live Update - IAA

I have a problem with Live Update on my 915p Neo2.
Live Update reports the latest IAA version as 4.5.0.6515 the installed version as 4.5.0.6515 but the actual installed version is 4.7.0.6815.
I have updated IAA separately outside of Live Update, but Live Update should show the installed version correctly as 4.7.0.6815 but it does'nt.
Anyone?

I think you need to dig to the device manager and check the real driver version. Live Update may report the wrong thing? Or you actually didn't manage to install the later version?

No picture with 4 sticks of ram (915P Neo2)

Hey, wonder if anyone can help. I am having trouble getting 4 sticks of ram to work with my motherboard... There seems to be a lot of threads around about this but I've not been able to find an answer. A few people have suggested it could be a problem with the motherboard
I get no picture on the screen if I have the ram in:
-All 4 slots.
-2 sticks in Channel A.
-Sticks in slots 1 + 3.
-Sticks in slots 2 + 4.
The only way I can get a picture is to have 2 sticks of ram in Channel B. I have updated the bios to the latest version (1.80) I have also tried lowering the memory speed to 400mhz and increasing the ddr voltage to 2.00v.
Spec:
motherboard: 915P Neo2 Platinum
ram: Geil ddr2 512mb pc2-4300 533mhz. x4
cpu: p4 3.2 lga775
If ive missed any info that you would need just let me know. Any reponse will be appreciated, as this has been puzzling me
Thanks,
John

Quote from: elektroscience on 07-June-06, 05:30:28
I have updated the bios to the latest version (2.80)
915P Neo2 Platinum doesn't have this bios. Where have you downloaded it?
915P Neo2 Platinum BIOS versions: 1.x
915P Neo2 Platinum (V1.0B) BIOS versions: 3.x
Please make sure you have flashed the proper bios.
What your PSU spec. It is better to create your own rig signature as others did.

915P Neo2 Hard drive incompatibility?

Greetings everyone,
I've been searching the forums for a while but haven't found any solutions. I'm trying to put together my new computer:
Intel 915p Neo2 LGA 775 platinum
P4 2.8
Corsair 512 DDR2
Quantum Fireball CX 3.5 series 15G (kinda old)
Maxtor 60G
At best, I can get the CMOS to recognize the hard drives as secondary master and slave and windows constantly fails to load. I've never had a problem like this in all the comps I've put together and none of my buddies are familiar with the board.
I've tried almost all cable and jumper combinations and the board still fails to recognize my hard drives as primary. We were able to get an old 5G hard drive to work even though it was a secondary, but only in safe mode. Is this a problem with RAID? I'm terribly unfamiliar with it. I would also not like to wipe my drives.
Has anyone had a similar problem? I would love to chat.
Best regards,
Scott

hi,
Are your HDDs SATA or IDE? I guess they are IDE, and in which IDE will be assigned as secondary, while Primary belongs to SATA.
There is nothing to do with RAID. You still have the options in the BIOS to choose the first drive to boot regardless primary or secondary.
Next is to take Danny advice and go for a fresh WinXP installation.

915P neo2 pl sound problem - still!!!

What up. I got:
Intel 915P neo2 platinum
P4 2.8
2x 512 MB DDR 533 Mhz
5.1 Philips speakers
Yes, I read the sticky topic in this section, yes I did the thing with manual installing driver but the problem is still here.
Here's my story:
I get brand new computer year and few months ago. I don't remember how I installed it cause most of it did my friend, but it was SURELY nothing special about it, cause I didn't even had and Internet connection in that house at the time so I didn't download anything special. Just drivers from CD. Everything was cool but last weekend I had to reinstall my Windows XP. I did that but after few hours of work in it I realized that subwoofer is not workin. The weird thing is, that it worked/work when I click on the pictures of speakers in that C Media driver... you know... the room with speakers where you can setup it's volume and girl is speakin "Left front", "Center"", "Subwoofer" etc. It work OK.
The problem is that it not work in normal applications, like BSplayer, Winamp, WMP or whatever. Not even 5.1 sound, only 2. Yes, I made setup in windows in sound settings to 5.1.
So I reinstalled Win again and installed the other one - without SP2 (I used SP2 before, didn't expect any problems). Couldn't install even the drivers from CD, at least SP1 required :-(
I'm soooo sick of this, I want finally solve it so PLEASE HELP ME!!!
Please write me step by step what to do, no matter if I have to reinstall Win again... I'll do it I just want it to be finally OK.
Thank you!

What up, thanks for replies.
Actually, what I did different was that thing with Realtek drivers. And after that finally those newest Cmedia drivers could find my device. It's better then it was. At least 5.1 works... but not in a good way. When I play 5.1 movie I hear only left & right channel, no surround or voices (center). :-(
I tried HL2 game and I think it was OK, 5.1. When I play any stereo music/video or anything I can hear it in ALL speakers. I always wanted it but what if I want to turn it off? What if I want stereo in stereo as it should be?

915P Neo2 - 54G Platinum CD needed (URGENT!!)

Please Please Please Please Please... has anyone got, or can make me a copy of the CD for this motherboard:
915P Neo2 - 54G Platinum
I stepped on the original accidentally, and with me at 18 stone it didn't stand much of a chance.
I can pay for postage etc and if it makes it easier, I have a paypal account. If anyone is local to me and has one of these boards all the better; I live in Mansfield, Nottinghamshire, UK.
All the best Lee
PS: if ya want a bit of resume check out my eBay feedback (http://feedback.ebay.co.uk/ws/eBayISAPI.dll?ViewFeedback&userid=darkan9el&ssPageName=STRK:ME:UFS)
Tried a bit of home research and well, I am totally confused now, I have never had such an awkward Motherboard to install and find files for as this one. nowhere on MSI's website is there a reference to an MSI 915P Neo2-54G Platinum. They make it but they don't acknowledge its existence!! ??? everything on the PC is new and has been tested using things like memtest etc and installing in other systems... I have 3 systems running. I've always had AMD systems before but thought I would try intel... never again!!
Is this the same moby as the: 915P Neo2 Platinum but with a wireless card added or is it a differnet moby altogether?
XP Pro SP2 comes up with errors on install, the disc tested fine in other systems, I even changed the CDwriter to an MSI one but it still kicked up a stink.

Hi Lee,
Sorry! I thought I had an answer for you that I posted here. I've modified my post to remove my suggestion after re-reading your request. I thought when I first read your post that the 54G in your model must have been a mistake on your part but after the re-read I see I was wrong.
Good luck finding a cd.
Mike

SLOW performance SATA HDD on the 915P Neo2 Platinum

Almost for a week I have tried to setup Windows XP prof. with SP2. Unfortunately the performance of the system is very poor.
For this reason I extended let test the system and compare the results with an other system.
My System Other system with diamond-maximum one 10, 160GB ATA133 disk
Disk - Sequential Read = 3.37 Disk - Sequential Read = 63.04
Disk - Sequential Write = 3.51 Disk - Sequential Write = 55.99
Disk - Random Seek + RW = 1.91 Disk - Random Seek + RW = 2.7
Disk Mark = 31.08 Disk Mark = 440.24
As you can see the result is awful.
Have tried all settings for a single HDD in the BIOS, but unfortunately no plausibly results got.
Is there people have the same problem ?
Kan any one help me out of this ?
My system configuration:
- Antec Sonata II 450 Watt
- Intel Pentium 4 630, Socket 775
- Corsair ValueSelect DDR2 SDRAM, 1 GB, PC4300, 533 MHz
- 915P Neo2 Platinum (V1.0B)
- 2x NEC ND-4550 16 connected to EDI 1
- 1x Maxtor DiamondMax Plus 10 250 GB, 7.200 rpm, 16 MB, SATA/150 connected to SATA_1
Thanks in advance !!

Can you try with HDSPEED? goto http://www.georgebreese.com/net/software/ and download HDSPEED. Look for the Bandwidth and Sequential. Sequential is the actual throughput speed of your HDD, some 55~65MB/s is pretty good. Bandwidth is your HDD cache throughput speed, which should be some 100MB/s.

Wich bios driver for 915P neo2 platinum-54g

915P neo2 platinum-54g m-board
P4 630 3,0GHZ cpu
2*512M Kingston 533MHz DDR2
Club3d 128MB Radeon x300se hypermem PCI-E
not sure of the power, but think it's 300w, 20-pin connector. (waiting a new power on monday, 400w ultra-low noise)
Sound Blaster Live! Platinum
So I read from the MSI site that the 915p neo2 platinum doesnt support p4 630, but the cpu support list says it does after the bios update..
But now Im not sure wich bios driver to use cause I cant find the exact model from the site.
I use that comp as a music studio comp and I get a crash in about half an hour the comp is on.. (using cubase program)
At first the crash appeared at cubase startup, but after I updated the g-card & s-card drivers the crash was post-poned to that half an hour..
But still, when I try the Core Center programs Auto overclocking test it crashes almost straight away.. Once I got from 200MHz to 205 MHz
Other times it crashed straight away..
So I think myself that the bios driver is the key, but Im not sure of it.
Or wich driver to use.. the 915P Neo2 Platinum (7028v18) or 915P Neo2 Platinum v1.0b (7028v36)

Quote from: ant3202 on 07-November-05, 08:00:33
use MSI life update to update your BIOS, to minimise to kill your mobo.
its not connected to the internet and I dont want to connect it cause its for music only...

Plz help 915P Neo2 Platinum temperature problem

Hi All
i have 915P Neo2 Platinum (V1.0B) main board
one day my computer stop working and when i press power button nothing happen
i change power supply and it work but when i log into windows it freez and stop responed
when i press restart button the computer didn`t work i had to remove power cable and put it again to work
i try linux it work for some time and stop respond and i had to remove power cable and put it again
my cpu temperature say it`s 59 but when i but my hand on fan i didn`t find it hot
i updated bios version
from this page
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=626&kind=1
to 3.6 because it said that fixed bios detect wrong CPU temperature.
some time the cpu temp say`s 104 c !!! put when i toutch the fan i didn`t find that it`s hot like that
some times when i press restart button it make shutdown not restart
i can`t install windows because it freez when i try to do that
i didn`t know why the computer work for some time and freez
and some times it didn`t work and i had to leave it for some time and try again
can any one help me to find why this happen is the problem in power supply that i replace it or what plz help
sorry for my language i speak english littel
Regards

Quote from: BOSSKILLER on 28-March-07, 19:38:10
what is your newest PSU? can you provide PSU details(can be found into PSU sticker), and remaining parts of your hardware e.g. what VGA you got?
"some time the cpu temp say`s 104 c !!! put when i toutch the fan i didn`t find that it`s hot like that "
seems your CPU heatsink is not making good contact with CPU surface, or there is too much thermal paste or CPU cooler is going down.
power down PC, remove power cord from the PSU and re seat CPU cooler, clean CPU socket from any dust, clean CPU surface from existing paste and apply a new one. then mount CPU cooler (ensure its mounted property, ensure CPU FAN is spinning at expected RPM). re-test, if no go, change your CPU cooler with new better one which gonna do the job.
thank you very much for your response
i change the PSU again with other and the computer work fine now
and use new cooler and the temp between 40-55 is this good ? new fan speed 3000 -4000 rpm
and sys temp is between 30-40
my hardware is
P4 3.0 LGA 1 MB cache
256 DDR2 x2
915P Neo2 Platinum v 1.0B
magic power supply 300W
Western Digital 80 GB x 2 @ ATA
VGA pci express 128 ATI
WinXP + SP2 + all latest Windows Updates

915P-Neo2 Platinum - Live Update Crashes

Is anyone else having trouble loading MSI's "Live Update", especially "Live Monitor" on the 915P Neo2 Platinum? Every time I load it the entire system collapes in the Blue Screen of Death upon reboot.
I've tried loading Live Update from both the enclosed "Drivers & Utilities" diskette and from the MSI Website where the latest version of Live Update (I guess) is located.
Both crash my new system the same. It just keeps looping at the Boot-Blue Screen-CRASH!-Boot-Blue Screen - CRASH!
The only way to recover is to do a Restore in Safe Mode.
Very disapponted with the 915P Neo2 Platinum board in general, i.e., the above reason and the slow, ragged - even sloppy - boot.
And if there is any advantage in these high-priced PCI-Express videocards that justifies the money, I can't find it. My old 875P Neo (signature system) smokes this new 915P even with its ungodly high-priced DDR2-675 memory.
Stay clear of 'em.

Quote
Originally posted by mike315
Is anyone else having trouble loading MSI's "Live Update", especially "Live Monitor" on the 915P Neo2 Platinum? Every time I load it the entire system collapes in the Blue Screen of Death upon reboot.
I've tried loading Live Update from both the enclosed "Drivers & Utilities" diskette and from the MSI Website where the latest version of Live Update (I guess) is located.
Both crash my new system the same. It just keeps looping at the Boot-Blue Screen-CRASH!-Boot-Blue Screen - CRASH!
The only way to recover is to do a Restore in Safe Mode.
Very disapponted with the 915P Neo2 Platinum board in general, i.e., the above reason and the slow, ragged - even sloppy - boot.
And if there is any advantage in these high-priced PCI-Express videocards that justifies the money, I can't find it. My old 875P Neo (signature system) smokes this new 915P even with its ungodly high-priced DDR2-675 memory.
Stay clear of 'em.
i 2nd this motion very disapointed with its compabiltiy and abillity to find drives
try harder MSI (Sorry very annoyed at this point)

915P Neo2 Platinum

Hope you guys can help i have the 915P Neo2 Platinum "NOT"(V1.0B) with the Broadcom BCM5751 onboard lan i had alot of the same problems with the sound and lan as others in this group and was able to fix it with the bios update. Every thing was fine untill i had to do a fresh install of xp home "dam kids" now my lan does not show up i made sure it was turned on in the bios and did another fresh install with no luck, hope you can help
Antec true430
+5V -5V +12V -12V +3.3V +5VSB
Max. Load 36A 0.5A 26A 1.0A 28.0A 2.0A
Min. Load 0A 0A 0.8A 0A 0A 0A
Load Reg. ±3% ±5% ±3% ±5% ±3% ±5%
Ripple V(p-p) 50mV 50mV 120mV 120mV 50mV 50mV

The very first thing to do after fresh installation is to install Intel INF driver. Have you done that?

915P Neo2 PE and stupid beeps

Similar Messages

Maybe you are looking for