A question about Kintex-7 configuration

Hi
I want to design a custom board with Kintex-7 FPGA(XC7K160T). I have a question about it's config. Can i use XCF128XFTG64 for this FPGA? If not, can you tell me what kind of Flash I can use?

Platform flash not supported in 7-series FPGA. Refer http://www.xilinx.com/support/answers/46093.html for details
As per "Table 1-1: Bitstream Length (Page-14) in configuration user guide (http://www.xilinx.com/support/documentation/user_guides/ug470_7Series_Config.pdf) the required bit stream length for XC7K160T device is 53,540,576 bits. By considering overheads the required size of flash is 64 Megabits or larger.
What version of tools are you using? What type of configuration mode are you planning? Refer “Configuration overview” topic (Page -11 onwards ) in http://www.xilinx.com/support/documentation/user_guides/ug470_7Series_Config.pdf to know different types of supported configuration modes.
You need to use CPLD/Microprocessor for slave Selectmap kind of configuration.
Impact tools(In case of using ISE tools) help topics list the supported BPI/SPI flash details in case of planning SPI/BPI kind of configuration modes.

Similar Messages

Support validity question about installing and configuring SP13 on same machine as FAST to use both as search engines for SP2010

Hi,
I have a SharePoint 2010 farm which is using its own servers.
This farm has a FAST Search for SharePoint server which is a standalone on a dedicated server.
This farm is my testing staging environment and not a Production environment, eventhough its almost an exact copy of the Production farm.
I would like to replace the FAST server with SharePoint 2013 as a search engine for my SharePoint 2010 farm.
Because i have a standalone deployment of FAST on a dedicated server and i dont have any more servers to add to this farm,
I would like to install SharePoint 2013 on same server as FAST while FAST is still active, connect it to the 2010 farm and do some tests before i will remove the FAST content and query SSA's.
I would like to know if installing a SP2013 on same machine as FAST is supported by Microsoft as long as the FAST is not connected to the SP2013? (performance is not an issue)
What about All in one machines like development servers, is it supported by Microsoft to install FAST on same machine as SP2010 farm? (again, performance is not an issue)
thanks,
Guy

I would like to know if this scenario is supported by microsoft.
This installation will be for testing purposes only, if there are any issues with installing SharePoint2013 on a FAST search machine, i would like to know what kind of problems i may run into.
I'd also like to clear out that this FAST and SharePoint2013 are not comunicating with eachother but with a SharePoint2010 farm that is configured on different servers.
I would really appreciate direct answers to these questions.
thanks for your answers,
Guy

Question about RADIUS server configuration with a MacBook Pro

Hello,
I own a modem router which is capable of WPA2 Enterprise and I want to use it with a RADIUS server for authentication and security purposes.
However, I have a few doubts about this.
MY CONFIGURATION:
The modem router would be connected to a fixed PC with Windows and to a MacBook Pro (both with Ethernet)
The RADIUS server would be running on the MacBook Pro (freeRADIUS)
The bold is the issue, that comes when I disconnect the MBP (it's a notebook, so I use it disconnected from the router sometimes).
Supposing the router would have recognized it (correct configuration), it would disconnect from it.
My questions:
Would Wi-Fi be lost in this manner? Or would the modem router automatically switch to another Wi-Fi authentication?
If I reconnected the MBP to the modem router and re-run the RADIUS server, would I need to access the control panel and re-configure the WPA2 Enterprise in order for Wi-Fi to work again?
Thanks in advance,
Tyrexionibus

"Full HD 3DD camcorder..." Marketing at it's best.
This is HDV, right? HDV has the same data rate as DV...13.6GB/hour. But because of the MPEG-2 Long GOP format the HDV format employs, it can be a bit tough to edit, but mainly when rendering effects. IT will be slower than DV, and you can't monitor thru the camera like you can with DV, but a simple FW400 drive and Intel Mac will be fine. Better if you can convert to ProRes upon ingest, but then that eats up a LOT more space and requires at least FW800...
http://library.creativecow.net/articles/poisson_chris/hdv-prores.php
Shane

Question about Active Directory Configuration

Hi All,
Portal Version : EP7.0 SP7
We want to configure Active directory as a Portal UME store.
We have 7 Domain controllers in the domain xyz.com. They are spread across locations. I assume, by default domain controller will have global catalog defined.
So in LDAP configuration, whether we to use Global Catalog (Port: 3268) to connect to ADS or LDAP connection(Port:389)?
I am not clear, when Global Catalog connection is defined to bind ADS to Portal UME?
Any suggestion?
Thanks & Regards,
Gowri

Hi Gowri,
It will work fine if you connect through port 389.
Can you please explain it in detail that How you have spread your domain controllers / your forest hierarchy?
Check if this helps.
Thanks,
Mittal

Question about transport system configure

I have two system dev & prd, the prd is domain controller, the router is from dev to prd.
I want to delete all transport configure and reconfigure it.   Now I login to prd 000, and delete dev from transport system, and use se06 to initial the stms, then I go to stms, the configure has been initialized.
But when I login dev000, the two systems configuration and the transport router is still exist in stms and I can not use se06 to inital it.   I am sure that in prd 000, the configuration has been deleted succussfully.
the configuration is still exists in dev000, and I can not do any operation from dev000 which is not domain controller, and the real control prd000 has been delete by me.
I try to use se06 , but after reinstall cts, I can still see the configuration in stms.
Could you give some solutions , Is there any problem with my operation?
thanks a lot.
Edited by: victor on Jan 11, 2009 9:17 AM
Edited by: victor on Jan 11, 2009 11:07 AM

Hello Victor,
you said PRD is the domain controller and successfully you
deleted previous configuration in PRD ,now login into DEV and
in the same delete the cofiguration in DEV too.when everything
is cleared you start from the first and start adding DEV to the
domain PRD.hope this helps.
regards,
Manjula.

Question about nForce2 memory configuration

Hi all,
I am running an MSI K7N2-L board with memory running 256|empty|256 in dual mode.
If I bought a stick of 512 and ran it 256|256|512, would it still run in dual mode?
Thanks in advance

if you have 2 sticks i think you put one in the separate slot and the other in one of the slots that are right next to each other (not sure on the colors at the moment) and if you have 3 sticks, 2 have to add up (MB wise) to the other one. (i.e. 2 256MB sticks and a 512MB stick) and you would put the 2 256MB sticks in the two slots right next to each other and the 512MB stick in the separate slot. Thats what i think anyway, i could be wrong. Its hard to explain, lol.

Question about SSLM configure

I have a question about our SSLM configure, please see the following example:
service aa-SSL
virtual ipaddr 172.25.17.15 protocol tcp port 443 secondary
server ipaddr 172.24.92.6 protocol tcp port 80
certificate rsa general-purpose trustpoint www.app.aa.com
no nat server
inservice
crypto pki trustpoint www.app.aa.com
revocation-check none
rsakeypair www.app.aa.com
crypto ca import www.app.aa.com pkcs12 tftp:xxx
======================================
Once we finish the configuration, we could find the corresponding cer in SSLM, like:
crypto pki certificate chain www.app.aa.com
My first question is how to remove this cert if we want to decommission aa-ssl environment? Is it only with âno crypto pki certificate chain www.app.aa.comâ
If we have another environment like www.pre.app.aa.com shared the same VIP with www.app.aa.com. My second question is could I create only one ssl entry with wildcard like the following configuration:
service aa-SSL
virtual ipaddr 172.25.17.15 protocol tcp port 443 secondary
server ipaddr 172.24.92.6 protocol tcp port 80
certificate rsa general-purpose trustpoint *.app.aa.com
no nat server
inservice
Please advice! I would appreciate it!

You can remove the certificate but you need to be in certificate chain configuration mode to delete certificates. An example configuration is provided here
http://www.cisco.com/en/US/docs/ios/security/command/reference/sec_c5.html#wp1043434

Some questions about configuration in MAX.

Hello,everyone!
I have some questions about configuration in MAX(I am a jackaroo for motion control development),I hope I can get your help.
I use PCI-7344+UMI-7764+Servo amplifier+Servo motor,my MAX version is 4.2 and I use NI-Motion7.5
My question as following:
1,In Axis Configuration,for motor type,why I must select stepper but not servo?my motor is servo motor!If I select Servo,my motor can't run,I don't know why.
If I select stepper,though motor can work but I can't test encoder in MAX.
2,In Stepper settings,for stepper loop mode,why I must select open-loop but not close-loop?If I select close-loop,the servo motor doesn't work too.
3,If I want my two servo motors run at different velocity,How shoud I do?It seems I just can set the same velocity in MAX for my two servo motors.
My English is poor,Pls pardon me!I come from China.
Thank you for your help!
EnquanLi
Striving is without limit!

Hi,Jochen,
Thank you for your kindly help!
The manufacturer of the drive and motor that I am using now is Japan SANYO DENKI,drive type is RS1A01AA,motor type is R2AA06020FXP00.
And I use position control mode,thehe encoder's counts per revolution is 131072.I set the electronic gear ratio to 1:1 for drive.
Now,I can use Close-Loop to control the motor but still has some problems.When I configure it to run in closed loop mode, the motors behave strangely and never move to the target position.When I configure it to run in closed loop mode, the motors behave strangely and never move to the target position.The detail situation is as following
1,Motor can't run.
2, Or motor moves to a position, then moves in the same direction agian and eventually stops.
Except for the two points mentioned above,"Following Error" is occured frequently,I don't know why.
I am still not clear why I must set the motor type be stepper in MAX .
And I have another question:what the relationship between the steps and the counts?They have the proportion relations?I notice that there are a section said like this in help document: For proper closed-loop and p-command operation, steps per revolution/counts per revolution must be in the range of 1/32,767 < steps/counts < 32,767. An incorrect counts to steps ratio can result in failure to reach the target position and erroneous closed-loop stepper operation.
I am verry sorry I have too many questions!
I am very appreciate for your kingly help!Thanks again!
EnquanLi
China
Striving is without limit!

I have a question about Configuration of Post with Clearing

I have a question about confiruation of the post with clearing which is t-doce 'FB05'.
When I make post with clearing on 'FB05', I can change the additional selections.
Where can I control the confiruation of the additional selections in t-code 'FB05'
Please, tell me the menu path.

Hi,
In SPRO, go to
Financial Accounting (New) > Accounts Receivable and Accounts Payable > Business Transactions > Incoming Payments > Manual Incoming Payments > Make Settings for Processing Open Items > Choose Selection Fields
Hope this helps.
Thanks

Question about configuring REST web service in EBS instance

I am from EBS SCM team. From one wiki page, it says OA Framework provides REST framework to expose OAF BC4J objects as web services. Can you provide more details about how to configure REST web service for one EBS instance? Any related information is also helpful.
Edited by: 936859 on Sep 7, 2012 5:45 PM

IIRC you must activate PAPI-WS for the engine. In Studio you do it by right-clicking on the project, then "engine preferences". In enterprise/standalone you must activate PAPI-WS in the Admin Center.

Questions about using Bitlocker without TPM

We currently use Bitlocker to encrypt our Windows 7 computers with TPM. Now we are looking at encrypting some Windows 7 computers without a TPM. I see how to change the group policy setting to allow Bitlocker without a TPM. I have looked at a lot of other
threads and I have a few questions about how the Bitlocker without TPM works.
1) I see a USB drive containing a key is required for Bitlocker configurations without a TPM, say the end user loses this USB drive, what are the recovery options for their computer?
This article seems to indicate that without the USB drive connected, you are unable to even access recovery options http://blogs.technet.com/b/hugofe/archive/2010/10/29/bitlocker-without-tpm.aspx
We have recovery backed up to AD when Bitlocker is enabled, but how could we do this recovery on a computer on computer where it's USB is lost? Would we have to remove the HD itself and attach it to another computer to access?
2) After enabling Bitlocker on a computer without a TPM and using the USB Drive for the key, is there a way to also add a PIN or password protection at bootup?

Hi,
Sorry for my dilatory reply,
Configuring a startup key is another method to enable a higher level of security with the TPM. The startup key is a key stored on a USB flash drive, and the USB flash drive must be inserted every time the computer starts. The startup key is used to provide
another factor of authentication in conjunction with TPM authentication. To use a USB flash drive as a startup key, the USB flash drive must be formatted by using the NTFS, FAT, or FAT32 file system.
You must have a startup key to use BitLocker on a non-TPM computer.
From: http://technet.microsoft.com/de-de/library/ee449438(v=ws.10).aspx#BKMK_Key
For more Q&A about BitLocker, you can refer to the link above.
hope this is helpful.
Roger Lu
TechNet Community Support

A lot of questions about my MacBook Air

I am really new to re-using Apple computers.The last time I used an Apple computer was back in 1987 when the school and my family had Apple IIGS computers. I have been using PC's which reqiure Microsoft. I a lot of have questions (10 questions) about my MacBook Air and I hope you good people can and will help me.
Product: MacBook Air
Operating System: Mac OS X Version 10.7.4
1) I Downloaded MacKeeper because I was fooled. I had a bad feeling just before I Downloaded it and I should have listened to my heart. However, I didn't buy it or fully Install it. It was like a test run and then they wanted me to pay almost $100 for it. Thankfully, I didn't because I read it is Malware. I spoke with an Apple Tech at Apple Care and he helped me get rid of it (or so we think). I don't see it anymore on my computer. I read it can slow down your computer. How can you tell if it's really off of the computer?
2) When I open "Finder" and I see that there are people Sharing my computer with me. I went into AirDrop and it reads, "Other people can see your Mac as (my name) MacBook Air when their computer is nearby." I bought a HotSpot and while it's turned on and I selected it as my WI-FI connection I thought it would get rid of these people, protect what I type, me, my items, computer, etc. But it didn't.
I didn't know that I have to buy a exteral CD and/or DVD Player in order to connect to the brand new Modem and Router in one by NetGear. I am so used to PCs and the CD/DVD Players being built inside.
The people at Apple Store told me that there is an internal modem inside, but I don't know how to find it and what to do then. Should I use a Firewall?, An AntiVirus, AntiMalware, AntiSpyware, etc. Apple Care tech told me I don't need to get an AntiVirus.
3) Is there a new kind of Wireless Modem and Router that doesn't require a CD-ROM?
4) When I travel or fly and I am not close to home I was told by Best Buy and Sprint that I had to buy a mobile HotSpot to use the computer (WI-FI) safely. As I typed, I have one. But it's pretty expensive and only gives me 1 hour and 15 minutes per day to Stream. What can I do to use this computer safely Online when I am out of range from a Modem and Router? What do people do when they travel on airplanes?
5) This compter won't let me use "Raid." I think you have to have a newer version. I hard about Raid on the radio from Leo (can't recall his last name) who's a Tech expert.
6) Should I buy a ZipDrive? Apple Store Tech told me that I didn't need a ZipDrive. I just remember the episode of HBO's "Sex and The City" when Carrie looses everything because her copy crashed. Now, of course, I know that's a fictional show, but with PC's and Microsoft I have lost everything when it crashed, frooze up, etc. I know there's iClouds. I heard about Carbonite, but I have read the Pros and Cons about it. Mostly they are Cons about it. I just don't want to do anything wrong and mess up this computer.
7) Should I buy a new Printer/Copier/Scanner because mine is an HP. It's not new, but it works. I even have a CD-ROM for Macs. What about the new product called, "Neat"?
8) Is there a special product that I should buy to do Online Banking and/or other important stuff?
9) I saw and read about iWork in the Apps Store and it sounds cool. I still have alot of friends and colleagues who still use Microsoft. Is iWork good to use? Should I Download it from the Apple Apps Store or can a buy it at Apple? Is there another Word Processing Program that is great and user friendly and will work with Macs and PCs?
10) Should I Update the OS with OS X Mountian Lion Pro from the Apple Apps Store or buy it at Apple Store?
In advance, I wish to thank you in this Apple Support Communites for your help. Have a safe and happy holiday weekend!

1) Here are instructions for removing MacKeeper. Since it mostly consists of manually looking for folders and specific files, if you follow the instructions you either fail to find what you are told to find (because your AppleCare guide gave you complete instructions which you followed) or you'll find some additional files that need to be replaced.
2 & 3) I assume you are looking at the sidebar of a Finder window and seeing Shared and computers under it. Those are computers that you can potentionally share. To do so you'd need an account on their computer and a password. They are not sharing your computer.
AirDrop allows you to create an adhoc network for filesharing and it only functions when you have selected the AirDop item in the SideBar. Actually doing that merely announces to computers in the same network node that your computer is available for a file to be sent to. Even then you have to explicitly allow the file to be downloaded to your computer. Similarly you'd be able to see other computers with AirDrop selected and be able to send them a file - which they'd have to accept.
The only reason your NetGear Router comes with a CD is to install and run their 'easy' step by step configuration program. It can also be done manually with a browser. Read the manual to find the IP address you must enter to access the router's configuration menu. Apple's WiFi routers don't require a CD to install the software because the configuration software is already on your computer.
I do have my firewall turned on. AntiVirus software isn't a bad idea - I use Sophos having tested it for a review for our local User Group and I found I liked it better than ClamAVx which is what I'd been using before. Both are free.
4) I think you were scammed by Sprint and BestBuy. I use hotel, coffee shop, and restaurant WiFi spots and have for years. However, because they can be unsecured, I do not shop online or bank when I'm using them. I also use 1Password and don't reuse passwords so even if a sniffer should grab an account and password that's all it would get - one account.
5) Raid doesn't really make sense with a MacBook Air - a RAID involves 2 or more disks being used as if they were one.
6) Zip drive? No. External hard drive - yes. It isn't a question of if a computer's hard drive will malfunction, it is when. OWC has a nice selection of external drives and the Mac has a built in backup system called TimeMachine. Due to the way TimeMachine works, I've found that your TimeMachine drive should be at least twice as large - and preferably 3-4 times as large as the data you are backing up.
7) if your printer works and it has Mountain Lion drivers, why replace it?
8) Online banking is done with a browser - Use Safari or FireFox
9) If trading files with Windows users is important Mac: Office is your best bet. If not, iWork, Mac:Office, or LibreOffice are all good possibilities.
10) you can only buy Mt Lion via the App Store.

Questions about Prompts -

Hi,
I have two questions about Prompt.
1) We have a dashboard with multiple tabs - We have noticed the Prompt Values copy from one tab to another. User doesn't want this to happen. Every tab should have there own default. Is it possible that previous tab prompt value should not copy to another tab prompt.
2) Is there a possible to have a prompt with Multi Select and Enterable field.
Thanks,
Poojak

hi,
Please see the answers below
1)You can set the dashboard prompt scope to 'Page'.In this way it will affect reports present only on that page
2)you can make a dashboard prompt 'Multiselect'.By default it will be drop down.If you go to your prompt there are options for these configuration.
Thanks
Sandeep

Questions about 3702i and WSM (WSSI)

I have several questions about the 3702i AP and the WSM that do not seem to be answered in the data sheets/documentation.
Any insight would be appreciated.
1. Is the WSM officially supported on the 3702 AP? The documentation seems to conflict on this.
For example, at the top of the WSM data sheet: "Flexible add-on third radio module for the Cisco Aironet 3600i or Cisco Aironet 3600e Series Access Points". Then later on in the page graphic shows the 3700 series radios too. I have found multiple pages that have similar conflicting information.
2. Can the WSM be used WITHOUT MSE and Cisco Prime? If so, are there any limitations?
3. How does the licensing work? Where is the license installed -- WLC, MSE, Prime? Do ANY of the features work without the license?
3a. How do you order the license? The SKU listed on the data sheet (L-WIPS-MM-1AP) is not a valid part number in CCW.
4. Is it possible to do sniffing with a WSM? (the idea being not having to dedicate an AP to sniffing, or taking down a client-serving AP to sniff)
Thank you.

Ok, so you are talking about off-channel scanning, which is actually a very short duration 50ms, that the AP is actually off-channel to scan.
http://mrncciew.com/2013/03/16/configuring-rrm/
Are you thinking of this bullet point?
Access points with wireless security module: The Cisco Aironet® Access Point Module for Wireless Security aggressively scans all channels without affecting the data-serving radios in the 2.4- and 5-GHz bands.
To me, that's just saying that the WSM is scanning and not interferring with the AP's normal radios.
HTH,
Steve

Two questions about SG300 DHCP server

Hi,
I have two questions about the DHCP server on the SG300:
On the Address Binding page, what does the "Declined" state mean? I have a NAS device that won't pull an address, and I think that the entry with a state of "Declined" corresponds to this device. It was previously pulling an address from a RV180, so the only difference is that it is now connected to the SG300. I worked around this by manually setting the address on the NAS device, but this won't scale if I run into a lot of other devices that can't pull an address.
I configured a static address binding for a WAP321 and found that instead of pulling the configured address that it pulled a dynamic address. I checked the Address Binding page and see that the dynamic entry that corresponds with the WAP321 has a Client Identifier rather than a MAC address. I changed the static entry for the WAP321 to use the client identifier displayed in the dynamic entry, and now the WAP321 pulls the configured static address. Is this expected behavior?
Thanks,
Bob

With the SX300/500 it is required the client identifier, it doesn't automatically insert it. If static DHCP is made on the switch and you didn't need client identifier, that is more or less fortunate behavior for you
So to answer this question, the expected behavior is to configure client identifier for static DHCP entry.
-Tom
Please mark answered for helpful posts
http://blogs.cisco.com/smallbusiness/

A question about Kintex-7 configuration

Similar Messages

Maybe you are looking for