ACARD AEC-6860M PCI RAID ATA 66 card not showing connected hard drives

I just installed an ACARD AEC-6860M PCI card in my G4 (Quicksilver 2002) and am having some difficulty getting Disk Utility to recognize the drives. I know other people in these forums have used this particular card before (Related thread: http://discussions.apple.com/thread.jspa?messageID=5688908), so I'm hoping you can help me.
The AEC-6860M is a PCI RAID card for 2 ATA drives. I've installed the drivers for the card and verified that it appears in System Profiler. However, no combination of drives or cables makes the 2 drives I have connected to it visible in System Profiler (under SCSI or ATA) or in Disk Utility, so I can't format them and actually use them.
Can anyone share any secrets? Thanks!
(See card details at http://store.mcetech.com/Merchant2/merchant.mvc?Screen=PROD&ProductCode=ACA-AEC-6860M&Category_Code=CLRNCINTCARDS&ProductCount=1)

Hello birdy.....,
Sorry to take so long responding. Major disaster! My whole wall bookcase just tumbled, and I'm still working at excavating the family (of Macs).
Your card should work. I've used the Acard cards by the dozens without problem, though I've never used that particular 6860 card or set up a RAID ARRAY. Just checked, using a 6880 (RAID) though as a controller card and not as a RAID ARRAY, and found that my 2002 QS Mac would not see a standard hard drive(#2) running OSX (10.2) that had been formatted by the OSX install disk using the stock bus on the motherboard. It would, however, see a hard drive(#3) that had been formatted while connected to an ACARD controller card (6280). I'm guessing that an OSX installer disk is prepared to see and to deal with a SCSI drive, and that Disk Utility is not.
Check that.
Just removed the controller card formatted drive(#3) and re-installed the OSX(10.2) drive(#2); this time my 2002 QS saw it right away, both on the desktop and in disk utility. I guess it needed personal messenger service.
As I recall, I've seen that happen before using controller cards; as a result, I've always taken care to format a new hard drive by connecting it to a controller card if that is the way I intend to use it. Hard drives can be capricious, sometimes. At any rate, try formatting your hard drive(s) with an OSX installer disk (hoping you have one) while connected to the ACARD controller card - just click on erase (twice) and the drive formats automatically.
I'm a little mystified by reference to drivers; never installed any drivers, and always assumed none were needed.
Hope that helps. Check back and let me know.
Jon

Similar Messages

MacBook not showing external hard drive connected to Air Port Extreme

I have a MacBook 5.2 running Mac OS X Version 10.5.7. I am running a wireless network Air Port Extreme router Version 7.4.2. I have connected a 1 TB Western Digital 10EAVS External hard drive and a printer to the Air Port Extreme router via a USB 2 hub. My MacBook sees and I am able to utilize the printer, but the Western Digital 1 TB External drive does not show up. I can see the 1 TB External drive via the Air Port Application setup, but it is not showing up on my desktop or in Utilities/Disk Utilities. I have connected the External drive directly to the USB port on my MacBook, and the drive showed up on my desktop instantly. I partitioned the External drive into two partitions and ran Time Machine which successfully backed up my MacBook. I then disconnected the External hard drive from my MacBook and reconnected it to another USB port in the hub connected to the Air Port Extreme. Once again, my MacBook does not see the External hard drive. I can see the External hard drive via the Air Port Extreme application right down to the two individual partitions. I even removed the USB hub and plugged the External hard drive directly into the Air Port Extreme router, but my MacBook still did not see the hard drive. I've restored version 7.4 and 7.4.1 on the Air Port Extreme, but it did not help. Does anyone have any insight what settings might need to be changed on my MacBook to allow it to connect to the External hard drive while it is plugged into the Air Port Extreme wireless router?

Do you have an older "dome" style AEBS or the rectangular model? The former will not work with TM. Early versions of the former may not work until you enable them to see a TM drive by doing the following:
Open the Terminal application in your Utilities folder. At the prompt paste the following command and press RETURN:
defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1
The drive should now be accessible via TM.

Does not show my hard drive when i try to install Tiger...

I have a Powerbook G4 that has no operating system installed yet, so when i try to install Tiger, i have to put the DVD in while booting up. I went to the installing screen, and i agreed to everything and all, but when i got to the part where it asks where to install, my hard drive does not show up. I went to DISK UTILITY and chose to erase the entire hard drive (I dont have anything on it yet) and I also chose to repair it. It didnt have any needed repairs, so I went back to the install screen, and it still didnt show the hard drive as an option. It is a 55.9 GB hard drive, and when i erase it, the size does not change, so I know there is nothing on it yet. In Disk Utility, the details for the Hard drive says it is named CSD CAT060L, it is a Disk, the media type is Generic, and it is Internal. I have tried this many times, but the exact same thing happens. My DVD for Tiger was unopened, and new out of the box. If you need any information about what happens or anything, just ask.
Thanks a bunch, Eshan.

Try this:
1. Boot from your Tiger DVD. After the installer loads select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.

Finder not showing connected network drives in Devices section

I have a number of network drives on my LAN, some NAS drives, some other Macs and of course a Time Machine. Prior to updating to OSX 10.9.5 when I used finder to connect to one of these shares the name of the connected share used to appear in the Finder Sidebar - under the devices section. Now when I do this nothing appears, although I do get an icon on the desktop and I can still access the remote files.
I have set/reset all the finder view settings from the Preferences panel and also tried deleting the finder and sidebar preferences files without improvement. I do have "Path Finder" installed as well and this still works as normal.
I contacted Apple support and after a hour or so they promised to get an engineer to get back to me sometime this week.
Has anyone else seen this behaviour ?
If Apple don't come up with any ideas I will have to experiment with uninstalling other apps which might indirectly case it, like Path Finder and even Paragon NTFS drivers.
It's not a show stopper, but a rather annoying inconvenience.
Thanks in advance for any replies
Dave

Hello birdy.....,
Sorry to take so long responding. Major disaster! My whole wall bookcase just tumbled, and I'm still working at excavating the family (of Macs).
Your card should work. I've used the Acard cards by the dozens without problem, though I've never used that particular 6860 card or set up a RAID ARRAY. Just checked, using a 6880 (RAID) though as a controller card and not as a RAID ARRAY, and found that my 2002 QS Mac would not see a standard hard drive(#2) running OSX (10.2) that had been formatted by the OSX install disk using the stock bus on the motherboard. It would, however, see a hard drive(#3) that had been formatted while connected to an ACARD controller card (6280). I'm guessing that an OSX installer disk is prepared to see and to deal with a SCSI drive, and that Disk Utility is not.
Check that.
Just removed the controller card formatted drive(#3) and re-installed the OSX(10.2) drive(#2); this time my 2002 QS saw it right away, both on the desktop and in disk utility. I guess it needed personal messenger service.
As I recall, I've seen that happen before using controller cards; as a result, I've always taken care to format a new hard drive by connecting it to a controller card if that is the way I intend to use it. Hard drives can be capricious, sometimes. At any rate, try formatting your hard drive(s) with an OSX installer disk (hoping you have one) while connected to the ACARD controller card - just click on erase (twice) and the drive formats automatically.
I'm a little mystified by reference to drivers; never installed any drivers, and always assumed none were needed.
Hope that helps. Check back and let me know.
Jon

WSE2012R2 Dashboard Stoage Tab Does Not Show ANY Hard Drives or Folders

I have been using WSE2012 for nearly two years as a "home" server. I recently decided to upgrade to R2. After spending several days trying to "migrate" to R2 without any success, I finally did a fresh install to my original system drive
(a 240Gb Samsung 840 Evo SSD). The install went well until I checked all of my data drives (4x2Tb, 2x1Tb, 1x3Tb and a 2Tb "storage spaces" drive). I found that only three of the drives were online and useable. The "storage spaces" drives
were not even visible in Disk Manager and all of the other drives were "offline". After doing a lot of searching with Google, I finally figured out how to make the "offline" drives "Online" with PowerShell. With much more searching,
I also finally figured out how to "bring back" the "storage spaces" drives with about four lines of PowerShell code so I thought I was finally home free... But no such luck. I then had a lot of trouble restoring my "ServerFolders"
although everything else seemed to be working. I also had rebooted several times while working on these things without any issues. After finishing up yesterday, I planning to finish working on the "ServerFolders" earlier today.
I ran into a problem right away, however, when I opened the Dashboard and went to the Storage tab only to find that NONE of the Hard Drives and "Server Folders" showed up. I had an alert that the "Server Storage Service" was
NOT running. I checked and found it to be "stopped" and in "manual" mode. After starting the service, the Storage Tab showed that it was being refreshed. After a lengthy wait, it never did refresh and the "Server Folders" item
on the Home Tab showed "N/A". I tried rebooting again. When the server came up, I checked the service again and found it to be running (although it was still on "manual")... But once again, Storage Tab never did refresh properly and still
showed nothing. This time I changed the service to "Auto" and also tried "Restarting" the service, to no avail. I rebooted again. This time, when it came back up, I first checked the service again and it was running and still on "Auto".
Before opening the Dashboard, I checked the "Files and Storage" section in "Server Manager" and everything looked good. All of my hard drives and my "storage spaces" drive appeared with no apparent issues so I thought that everything
was finally OK... Wrong!!!!! I opened the Dashboard and went back to the Storage Tab only to find that it still would NOT refresh so that NONE of my hard drives or folders were showing. I am totally lost at the moment. How can everything actually be there
and okay but NOT appear in the Dashboard which, by the way, was working fine yesterday -- and I did not make any changes whatsoever between yesterday and starting to work on the system today. I am totally lost. Can anyone please help me resolve this
issue?????
Denis W. Repke

PROBLEM SOLVED. As I was just getting ready to "bite-the-bullet" and reinstall 2012 R2, I discovered something that led me to the solution. When I was previously trying to restart the Windows Storage Service, I "thought" it was restarting
okay. I was restarting it by right-clicking on the service. When I "started" it this way without opening up the service properties, it would immediately change from "stopped" to "running". What I did not realize was that the service
was quickly stopping "without" refreshing the screen so that "running" was still displayed even though the service had stopped. Once I realized that the service was not actually restarting, I tried another Google search based on this fact
which led me to some forum threads that helped me solve the problem since I found others with essentially the same problem. I found two corrupted registry keys under Windows Server\Storage Services. One of the keys was a major entry, the other was in the "Folders"
subfolder. After deleting BOTH keys, the service restarted without any issues and my drives and folders reappeared in the dashboard. A reboot was "not" required. What a pain! But everything is good now.
Denis W. Repke

Mac Mini server not showing second hard drive

early 2009 mini server suddenly won't show the second hard drive for time machine. All I get in the system profiler is this?
Is my hard drive toast or is there any idea out there of how to recover it?
Thanks for the help! Running 10.6.8 server by the way.

Maybe the connector to the HD come loose. That happend abount a month ago on my 2009 Mini

Help my computer does not recognise my hard drive

Hi All,
Yesterday I turned my computer on to find that it would not start up. I tried following advice etc about starting up in safe mode etc but no help what I have found is that he computer does not recognise the hard drive anymore so when I out the osx install disk in and run system profiler and disk utility it does not show a hard drive. I have not done anything for this to happen. Can anyone help me with this.
Thanks.
Paul

Instead of using older OS X CD/DVD install to a new drive.
Where is your backup and clone?
Buy some drives! that is a must.
Pick up a FW case, you will need it to put the old drive in, and later, so you have an external and off line drive for backups and maintenance.
A copy of TechTool Pro 4/5 and Disk Warrior (DW first).
SuperDuper to clone your drives.
Demo of Prosoft Data Rescue 3 to scan the drive once you have a system and you put the 'dead' drive in FW case.
Then do backups and preventative maintenance on a very regular basis and have at least two backup sets.
If you have been doing that, and know and have read those instructions in the past....

SD Card not showing after Mountain Lion Update

This matter has been discussed for some time now in
Apple Support Communities > Desktop Computers > iMac (Intel) > Discussions
SD Card not showing after Mountain lion Update
Since the update to Mountain Lion, the SD slot does not show up in Finder.
Someone gave a fix using the killall in Terminal, and that worked only once. I have not been able to get that fix to work again.
The only saving grace for me is that my SD Card us is always from my Nikon camera, and Nikon ViewNX 2 software is able to see and read from the card.
Killall may have worked partially in that I no longer get the error message telling me that I have removed the SD card improperly, and need to dismount it first.
However, Finder still cannot see it.

BrianForbesColgate wrote:
Thanks, Barney ...
Those are basics ... Been there, done that, first.
Then you should hava posted all the troubleshooting you already accomplished.
Does the card show up in System Information? Or is that another one of the "basics" you've already looked into?
Does it show up in Disk Utility? If so, have you tried formatting it there to determine if it is a formatting problem?

BlackMagic Intensity Pro Capture Card & (3) 1TB Internal Hard Drives

Hello,
This is my first time using BM Intensity Pro. Prior to tonight all I used was FW400 & iMovie/iDVD.
I have now upgraded to Final Cut Studio with a BM Intensity Pro Capture Card and Three 1TB Hard Drives (7200 RPM with 32MB cache) - Striped as a RAID set to create ONE 2.7 TB HD for Video Storage.
I have a few questions that I would like some help with.
I would like to capture at the highest video quality possible.
I'm worried that Hard Drives wont be able to handle the capture speed or file size?
I ran the BM Disk Speed Test. I'm just not sure what all these numbers mean?
Can someone please explain to me what the following information is telling me?
Do the results mean that I'm good to go with uncompressed HDV via HDMI?
The first is my OEM Mac Hard Drive. The second is my 3TB RAID set.
Blackmagic Disk Speed Test Results
Date: 2009-06-07 22:10:23 -0400
Mac OS X Version: 10.5.7
Physical Memory: 2047 MB
QuickTime Version: 7.6.2
Read Speed: 62.5 MB/s
Write Speed: 60.9 MB/s
Blackmagic Disk Speed Test Results
Date: 2009-06-07 22:13:26 -0400
Mac OS X Version: 10.5.7
Physical Memory: 2047 MB
QuickTime Version: 7.6.2
Read Speed: 314.9 MB/s
Write Speed: 310.0 MB/s

About using the speed test:
http://forums.creativecow.net/thread/124/864289
I would invest in an external RAID controller.
You can find a variety of such from AMUG in RAID5/6 that will support higher sustained thruput.
http://www.amug.org/amug-web/html/amug/reviews/reviews.html
http://www.amug.org/amug-web/html/amug/reviews/articles/highpoint/4322/
http://www.barefeats.com/hard115.html
http://www.amug.org/amug-web/html/amug/reviews/articles/highpoint/3522/
http://www.barefeats.com/hard101.html
Those should also give you a better feel for what to do with those numbers and what to look for.

System Profiler will not recognize installed hard drive if drive is in use by VMWare

System Information will not recognize installed Hard Drive (Boot Camp) when in use by VMWare.
I work in IT for a School District and I am creating a Script that system information about the computer. I am testing this on a Mac Pro with two internal hard drives. One drive is Mac OS 10.8 and the other drive is a Boot Camp Drive that is used by VMWare Fusion.
When I run System Information via the GUI or system_profiler via Terminal, both drives show up just fine. However, if I launch VMWare Fusion and run Windows from my Boot Camp drive, then run System Information via the GUI or system_profiler via Terminal, the Boot Camp Drive is no longer listed as an installed drive.
Example:
In the Terminal, I enter the following command.
system_profiler SPStorageDataType
Then it returns this information.
Storage:
    Lion Client:
      Available: 217.84 GB (217,836,306,432 bytes)
      Capacity: 639.28 GB (639,275,270,144 bytes)
      Mount Point: /
      File System: Journaled HFS+
      Writable: Yes
      Ignore Ownership: No
      BSD Name: disk0s2
      Volume UUID: CCB501BF-AF24-30E7-A938-5A4E52DF14D7
      Physical Drive:
          Media Name: WDC WD6400AAKS-41H2B0 Media
          Medium Type: Rotational
          Protocol: SATA
          Internal: Yes
          Partition Map Type: GPT (GUID Partition Table)
          S.M.A.R.T. Status: Verified
    BOOTCAMP:
      Available: 255.58 GB (255,575,560,192 bytes)
      Capacity: 319.79 GB (319,790,510,080 bytes)
      Mount Point: /Volumes/BOOTCAMP
      File System: NTFS
      Writable: No
      Ignore Ownership: Yes
      BSD Name: disk1s2
      Volume UUID: D4B39D4E-E244-403C-AE4D-4D58397130DE
      Physical Drive:
          Media Name: WDC WD6400AAKS-41H2B0 Media
          Medium Type: Rotational
          Protocol: SATA
          Internal: Yes
          Partition Map Type: GPT (GUID Partition Table)
          S.M.A.R.T. Status: Verified
Then I launch VMWare, which uses the Boot Camp drive. The once again run the same command from the Terminal Command and I get this.
Storage:
    Lion Client:
      Available: 213.39 GB (213,392,244,736 bytes)
      Capacity: 639.28 GB (639,275,270,144 bytes)
      Mount Point: /
      File System: Journaled HFS+
      Writable: Yes
      Ignore Ownership: No
      BSD Name: disk0s2
      Volume UUID: CCB501BF-AF24-30E7-A938-5A4E52DF14D7
      Physical Drive:
          Media Name: WDC WD6400AAKS-41H2B0 Media
          Medium Type: Rotational
          Protocol: SATA
          Internal: Yes
          Partition Map Type: GPT (GUID Partition Table)
          S.M.A.R.T. Status: Verified
The Boot Camp Drive is no longer listed.
I assume this is due to the the fact that the drive is "In Use" however is seems odd since the Mac drive is also in use and it appears without problem. I assume there is no "fix" for this, I was just wondering if someone may have an explaination why?
Also, I do realize that I can query the various interface types like system_profiler SPSerialATADataType to get all the properly installed phycial drives, but then I would have to query all possible interface types, isolate only devices containing Volumes, then consoldate the information to just the information that I need. I was hoping for a cleaner query.

Thank you for your response.
VMWare may be the cause, but the actual issue I am having is with Apple's System Information. I anticipated resistance from VMWare if I went to them with a question about an Apple software issue (even though VMWare software is part of the equation). I was trying to avoid the inevitable finger pointing game. I thought I would try with Apple Forums first since the issues presents itself within the Apple Software. However, you are correct that VMWare may have an explanation on why Fusion might be interfering with System Information. I will check with them next.
To answer your question. Yes, In most cases I do use Fusion to run Windows side-by-side with the Mac OS. However, that is not always the case. There are a few reasons why I have it setup using a Dual Boot configuration.
One, in some cases, due to the intense programs I occasionally run (graphic applications), I prefer to simply boot straight into Windows via Boot Camp so I may allocate all hardware resources to Windows. Additionally, some graphic applications like to have direct access to hardware and the extra layer of the VM environment can cause problems when an application is trying to directly access specific hardware like a graphics card.
Second, I often use either side, both Mac and PC, for testing. There is an advantage to not having to rely on the Mac OS to run Windows. If, for whatever reason, my Mac becomes unstable due to testing, I can still jump right into Windows to do work if necessary.
Third, I love the Mac OS, but I work in a PC centric organization. If there is a "problem" with my system, it is too easy for other system admins to say, "it's because it's a Mac". Having the definitive separation of the OS's allows me to prove that the Mac OS is not a factor.

I cannot get my photos to download off my memory card to an external hard drive through bridge on a mac book pro.

i cannot get my photos to download off my memory card to an external hard drive through bridge on a mac book pro. it comes up with a message Cannot write to specified directory. Please choose a different directory.

Do not store them in the Cloud. It isn't really storage. For iTunes purchases, for example, it is just re-downloading a purchase. If a label decides to no longer make the item available it will disap[pear from the cloud and that will be it for you.
You can't store items on an external drive simply by dragging them there. That's too complicated for iTunes and how it is set up to work. I know I post on this 10x a week and there's many other posts discussing this. I suggest you browse a bit first. Your options are basically to either put your whole library on the eternal drive (which is a nuisance if you don't want to drag it everywhere with you), or to copy individual items to the external drive, delete them from the internal drive, then re-add them as new items (re-adding to playlists, etc.).

IPad as intermediary between cf card reader and external hard drive?

Would it be possible, using any combination of accessories, to use an ipad to facilitate the download of my canon 7d's video files from a cf card to an external hard drive? I bought a netbook to do this and I just hate it. Not that it doesn't do it's job but that's all i need it for and i'd rather use the ipad if possible. any ideas?

No - you cannot connect an external drive to the iPad.

Msi Live Update....not Show The Last Driver

Hi
whe MSI Live Monitor (MSI Live Update 3), search.. not show, the last driver...and bios....
I have a G4MX460-VTP
and the driver in the MSI Live Update is:
Online Ver. 4403 (MSI Version)
but when visit the MSI webpage (http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=154) the last driver is:
Nvidia driver 45.32 for Win2000/WinXP/Server2003 OS
and in the Nvidia webpage is 50.16.....
and the same happend with the VGA Bios...
y fix my vga cad update the VGA bios....but...this update don't show in the Live Update 3
How fix it???
thanks

Do not update the VGA BIOS unless you have a good reason to. It is not like a motherboard.
Go to nVidia Drivers if you want the latest drivers.
Live Update may not have been updated OR the version reported by the Live Update utility has been tested successfully with that card. Newer drivers sometimes cause problems with older cards. The only way to know for sure is got to the nVidia site and try the latest.

Windows XP re-installation does not recognize any hard drive - help

Hi,
I have X60s Model: 17044JU
I have original XP installed.
My computer is very slow and I am trying to reinstall XP from my CD (and format HD so I clean everything).
When Windows installations blue screen shows up and loads drivers etc then it tells me that it does not recognize any hard drive.
I thought I may need SCSI or RAID drivers but since I don't have floppy I can not load them.
Any help how to install new XP would be appreciated.
Thank you
Miron
Moderator edit: Masked serial number to prevent mis-use.
Solved!
Go to Solution.

Hi
I changed BIOS setup from AHCI to Compatibility and indeed it worked.
However there is easier way to reload new system on thinkpad.
I didn't know that but you can press ThinkVantage button when you start your laptop and IBM utilities start up.
Then there is an option to reload the system to be in original state as shipped from the factory. It loads or drivers and initial programs. It also formats your hard drive.
I found it pretty convenient.
Thanks for help.
mc

Mac Not Recognizing External Hard Drive, I Want to Use the HDD to boot Windows

Let's get this stuff straight first:
The Hard Drive is from a PC that I am not using
The Hard Drive already has Windows 8.1 installed as well as all my documents and data. (from the old PC, of course.)
It does work, however after connecting it to my iMac (late 2014 / 5K Retina) it isn't recognized by Finder, Disk Utility or the (Option) Boot screen.
Yes, I understand I will need to install drivers, so I'll need help doing that as soon as we get Yosemite to recognize the HDD.
What I am wanting to do is use this external drive to run Windows from the boot up screen. But I need OS X to actually recognize the drive in the first place. Then I'll need a little help installing the drivers for Windows onto the Drive, unless those are already installed, since it was originally used in my PC? (I'm not sure how drivers work.)
Nonetheless, if it's not possible to be used as an external boot for Windows, I'd still like to use it to obtain and store files/documents on.
Thanks guys!
-Austin

How do you have the drive hooked up to your computer? Did you but an adapter? If so, is it one that is supposed to work with a Mac? Did it come with a power supply?
Some of those USB adapters don't work well with Macs and that could be causing problems. Test it on a PC if possible, just to make sure the adapter itself isn't bad.
~Lyssa

ACARD AEC-6860M PCI RAID ATA 66 card not showing connected hard drives

Similar Messages

Maybe you are looking for